4 ADC/8 DAC with PLL,
192 kHz, 24-Bit CODEC
AD1939
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
2006 Analog Devices, Inc. All rights reserved.
FEATURES
PLL generated or direct master clock
Low EMI design
112 dB DAC/107 dB ADC dynamic range and SNR
-94 dB THD + N
Single 3.3 V supply
Tolerance for 5 V logic inputs
Supports 24-bits and 8 kHz to 192 kHz sample rates
Differential ADC input
Differential DAC output
Log volume control with autoramp function
SPI controllable for flexibility
Software controllable clickless mute
Software power-down
Right-justified, left-justified, I
2
S, and TDM modes
Master and slave modes up to 16-channel in/out
64-lead LQFP package
APPLICATIONS
Automotive audio systems
Home Theater Systems
Set-top boxes
Digital audio effects processors
GENERAL DESCRIPTION
The AD1939 is a high performance, single-chip codec that
provides four analog-to-digital converters (ADCs) with
differential input and eight digital-to-analog converters (DACs)
with differential output using the Analog Devices, Inc. patented
multibit sigma-delta (-) architecture. An SPI port is included,
allowing a microcontroller to adjust volume and many other
parameters. The AD1939 operates from 3.3 V digital and analog
supplies. The AD1939 is available in a 64-lead (differential
output) LQFP package.
The AD1939 is designed for low EMI. This consideration is
apparent in both the system and circuit design architectures.
By using the on-board PLL to derive the master clock from the
LR clock or from an external crystal, the AD1939 eliminates
the need for a separate high frequency master clock and can
also be used with a suppressed bit clock. The digital-to-analog
and analog-to-digital converters are designed using the latest
ADI continuous time architectures to further minimize EMI.
By using 3.3 V supplies, power consumption is minimized,
further reducing emissions.
FUNCTIONAL BLOCK DIAGRAM
DIGITAL
FILTER
SERIAL DATA PORT
DIGITAL AUDIO
INPUT/OUTPUT
PRECISION
VOLTAGE
REFERENCE
TIMING MANAGEMENT
AND CONTROL
(CLOCK AND PLL)
CONTROL PORT
SPI/I
2
C
CONTROL DATA
INPUT/OUTPUT
AD1939
ADC
ADC
ADC
ADC
ANALOG
AUDIO
INPUTS
ANALOG
AUDIO
OUTPUTS
DAC
DAC
DAC
DAC
DAC
DAC
DAC
DAC
DIGITAL
FILTER
AND
VOLUME
CONTROL
SDATA
OUT
SDATA
IN
CLOCKS
06
07
1-
0
01
Figure 1.
AD1939
Rev. 0 | Page 2 of 32
TABLE OF CONTENTS
Features .............................................................................................. 1
Applications....................................................................................... 1
General Description ......................................................................... 1
Functional Block Diagram .............................................................. 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Test Conditions............................................................................. 3
Analog Performance Specifications ........................................... 3
Crystal Oscillator Specifications................................................. 4
Digital Input/Output Specifications........................................... 5
Power Supply Specifications........................................................ 5
Digital Filters................................................................................. 6
Timing Specifications .................................................................. 6
Absolute Maximum Ratings............................................................ 8
Thermal Resistance ...................................................................... 8
ESD Caution.................................................................................. 8
Pin Configuration and Function Descriptions............................. 9
Typical Performance Characteristics ........................................... 11
Theory of Operation ...................................................................... 13
Analog-to-Digital Converters (ADCs).................................... 13
Digital-to-Analog Converters (DACs) .................................... 13
Clock Signals............................................................................... 13
Reset and Power-Down ............................................................. 14
Serial Control Port ..................................................................... 14
Power Supply and Voltage Reference....................................... 15
Serial Data Ports--Data Format............................................... 15
Time-Division Multiplexed (TDM) Modes............................ 15
Daisy-Chain Mode ..................................................................... 19
Control Registers ............................................................................ 24
Definitions................................................................................... 24
PLL and Clock Control Registers............................................. 24
DAC Control Registers .............................................................. 25
ADC Control Registers.............................................................. 27
Additional Modes....................................................................... 29
Application Circuits ....................................................................... 30
Outline Dimensions ....................................................................... 31
Ordering Guide .......................................................................... 31
REVISION HISTORY
7/06--Revision 0: Initial Version
AD1939
Rev. 0 | Page 3 of 32
SPECIFICATIONS
TEST CONDITIONS
Performance of all channels is identical, exclusive of the interchannel gain mismatch and interchannel phase deviation specifications.
Supply voltages (AVDD, DVDD)
3.3 V
Temperature range
1
as specified in Table 1 and Table 2
Master clock
12.288 MHz (48 kHz f
S
, 256 f
S
mode)
Input sample rate
48 kHz
Measurement bandwidth
20 Hz to 20 kHz
Word width
24 bits
Load capacitance (digital output)
20 pF
Load current (digital output)
1 mA or 1.5 k to DVDD supply
Input voltage HI
2.0 V
Input voltage LO
0.8 V
1
Functionally guaranteed at -40C to +125C case temperature.
ANALOG PERFORMANCE SPECIFICATIONS
Specifications guaranteed at 25C (ambient).
Table 1.
Parameter Conditions/Comments
Min
Typ
Max
Unit
ANALOG-TO-DIGITAL
CONVERTERS
ADC Resolution
All ADCs
24
Bits
Dynamic Range
20 Hz to 20 kHz, -60 dB input
No Filter (RMS)
96
102
dB
With A-Weighted Filter (RMS)
98
105
dB
Total Harmonic Distortion + Noise
-1 dBFS
-96
-87
dB
Gain
Error
-10
+10 %
Interchannel Gain Mismatch
-0.25
+0.25
dB
Offset
Error
-10 0
+10 mV
Gain
Drift
100 ppm/C
Interchannel
Isolation
-110 dB
CMRR
100 mV rms, 1 kHz
55
dB
100 mV rms, 20 kHz
55
dB
Input
Resistance
14
k
Input
Capacitance
10
pF
Input Common-Mode Bias Voltage
1.5
V
DIGITAL-TO-ANALOG
CONVERTERS
Dynamic Range
20 Hz to 20 kHz, -60 dB input
No Filter (RMS)
102
107
dB
With A-Weighted Filter (RMS)
105
110
dB
With A-Weighted Filter (Avg)
112
dB
Total Harmonic Distortion + Noise
0 dBFS
Two channels running
-94
dB
Eight channels running
-86
-76
dB
Full-Scale Output Voltage
1.76 (4.96)
V rms (V p-p)
Gain
Error
-10
+10 %
Interchannel Gain Mismatch
-0.2
+0.2
dB
Offset
Error
-25 -6
+25 mV
Gain
Drift
-30
+30 ppm/C
Interchannel
Isolation
100 dB
Interchannel Phase Deviation
0
Degrees
AD1939
Rev. 0 | Page 4 of 32
Parameter Conditions/Comments
Min
Typ
Max
Unit
Volume
Control
Step
0.375 dB
Volume
Control
Range
95
dB
De-emphasis Gain Error
0.6
dB
Output Resistance at Each Pin
100
REFERENCE
Internal Reference Voltage
FILTR pin
1.50
V
External Reference Voltage
FILTR pin
1.32
1.50
1.68
V
Common-Mode Reference Output
CM pin
1.50
V
REGULATOR
Input Supply Voltage
VSUPPLY pin
4.5
5
5.5
V
Regulated Output Voltage
VSENSE pin
3.19
3.37
3.55
V
Specifications measured at 130C (case).
Table 2.
Parameter Conditions/Comments
Min
Typ
Max
Unit
ANALOG-TO-DIGITAL CONVERTERS
ADC Resolution
All ADCs
24
Bits
Dynamic Range
20 Hz to 20 kHz, -60 dB input
No Filter (RMS)
93
102
dB
With A-Weighted Filter (RMS)
96
104
dB
Total Harmonic Distortion + Noise
-1 dBFS
-96
-87
dB
Gain Error
-10
+10
%
Interchannel Gain Mismatch
-0.25
+0.25
dB
Offset Error
-10
0
+10
mV
DIGITAL-TO-ANALOG CONVERTERS
Dynamic Range
20 Hz to 20 kHz, -60 dB input
No Filter (RMS)
101
107
dB
With A-Weighted Filter (RMS)
104
110
dB
With A-Weighted Filter (Average)
112
dB
Total Harmonic Distortion + Noise
0 dBFS
Two channels running
-94
dB
Eight channels running
-86
-70
dB
Full-Scale Output Voltage
1.76 (4.96)
V rms (V p-p)
Gain Error
-10
+10
%
Interchannel Gain Mismatch
-0.2
+0.2
dB
Offset Error
-25
-6
+25
mV
Gain Drift
-30
+30
ppm/C
REFERENCE
Internal Reference Voltage
FILTR pin
1.50
V
External Reference Voltage
FILTR pin
1.32
1.50
1.68
V
Common-Mode Reference Output
CM pin
1.50
V
REGULATOR
Input Supply Voltage
VSUPPLY pin
4.5
5
5.5
V
Regulated Output Voltage
VSENSE pin
3.2
3.43
3.65
V
CRYSTAL OSCILLATOR SPECIFICATIONS
Table 3.
Parameter
Min
Typ
Max
Unit
Transconductance
3.5
mmhos
AD1939
Rev. 0 | Page 5 of 32
DIGITAL INPUT/OUTPUT SPECIFICATIONS
-40C < T
A
< +130C, DVDD = 3.3 V 10%.
Table 4.
Parameter Conditions/Comments
Min
Typ
Max
Unit
Input Voltage HI (V
IH
)
2.0
V
Input Voltage HI (V
IH
) MCLKI/XI
pin
2.2
V
Input Voltage LO (V
IL
)
0.8
V
Input Leakage
I
IH
@ V
IH
= 2.4 V
10
A
I
IL
@ V
IL
= 0.8 V
10
A
High Level Output Voltage (V
OH
)
I
OH
= 1 mA
DVDD - 0.60
V
Low Level Output Voltage (V
OL
)
I
OL
= 1 mA
0.4
V
Input Capacitance
5
pF
POWER SUPPLY SPECIFICATIONS
Table 5.
Parameter Conditions/Comments
Min
Typ
Max
Unit
SUPPLIES
Voltage
DVDD
3.0
3.3
3.6
V
AVDD
3.0
3.3
3.6
V
Digital Current
MCLK = 256 f
S
Normal Operation
f
S
= 48 kHz
56
mA
f
S
= 96 kHz
65
mA
f
S
= 192 kHz
95
mA
Power-Down f
S
= 48 kHz to 192 kHz
2.0
mA
Analog Current
Normal Operation
74
mA
Power-Down
23
mA
DISSIPATION
Operation
MCLK = 256 f
S
, 48 kHz
All Supplies
429
mW
Digital Supply
185
mW
Analog Supply
244
mW
Power-Down, All Supplies
83
mW
POWER SUPPLY REJECTION RATIO
Signal at Analog Supply Pins
1 kHz 200 mV p-p
50
dB
20 kHz 200 mV p-p
50
dB
AD1939
Rev. 0 | Page 6 of 32
DIGITAL FILTERS
Table 6.
Parameter Mode
Factor
Min
Typ
Max
Unit
ADC DECIMATION FILTER
All modes, typ @ 48 kHz
Pass Band
0.4375 f
S
21 kHz
Pass-Band Ripple
0.015
dB
Transition Band
0.5 f
S
24 kHz
Stop Band
0.5625 f
S
27 kHz
Stop-Band Attenuation
79
dB
Group Delay
22.9844/f
S
479 s
DAC INTERPOLATION FILTER
Pass Band
48 kHz mode, typ @ 48 kHz
0.4535 f
S
22 kHz
96 kHz mode, typ @ 96 kHz
0.3646 f
S
35
kHz
192 kHz mode, typ @ 192 kHz
0.3646 f
S
70 kHz
Pass-Band Ripple
48 kHz mode, typ @ 48 kHz
0.01
dB
96 kHz mode, typ @ 96 kHz
0.05
dB
192 kHz mode, typ @ 192 kHz
0.1
dB
Transition Band
48 kHz mode, typ @ 48 kHz
0.5 f
S
24 kHz
96 kHz mode, typ @ 96 kHz
0.5 f
S
48 kHz
192 kHz mode, typ @ 192 kHz
0.5 f
S
96 kHz
Stop Band
48 kHz mode, typ @ 48 kHz
0.5465 f
S
26 kHz
96 kHz mode, typ @ 96 kHz
0.6354 f
S
61 kHz
192 kHz mode, typ @ 192 kHz
0.6354 f
S
122 kHz
Stop-Band Attenuation
48 kHz mode, typ @ 48 kHz
70
dB
96 kHz mode, typ @ 96 kHz
70
dB
192 kHz mode, typ @ 192 kHz
70
dB
Group Delay
48 kHz mode, typ @ 48 kHz
25/f
S
521 s
96 kHz mode, typ @ 96 kHz
11/f
S
115 s
192 kHz mode, typ @ 192 kHz
8/f
S
42 s
TIMING SPECIFICATIONS
-40C < T
A
< +130C, DVDD = 3.3 V 10%.
Table 7.
Parameter Condition
Comments
Min
Max
Unit
INPUT MASTER CLOCK (MCLK)
AND RESET
t
MH
MCLK duty cycle
DAC/ADC clock source = PLL clock @ 256 f
S
, 384 f
S
,
512 f
S
, 768 f
S
40 60 %
t
MH
DAC/ADC clock source = direct MCLK @ 512 f
S
(bypass
on-chip PLL)
40 60 %
f
MCLK
MCLK frequency
PLL mode, 256 f
S
reference
6.9
13.8
MHz
f
MCLK
Direct 512 f
S
mode
27.6
MHz
t
PDR
Low
15
ns
t
PDRR
Recovery
Reset to active output
4096
t
MCLK
PLL
Lock time
MCLK and LRCLK
input
10
ms
256 f
S
VCO Clock
40
60
%
Output Duty Cycle
MCLKO/XO pin
AD1939
Rev. 0 | Page 7 of 32
Parameter Condition
Comments
Min
Max
Unit
SPI PORT
See Figure 11
t
CCH
CCLK high
35
ns
t
CCL
CCLK low
35
ns
f
CCLK
CCLK frequency
f
CCLK
= 1/t
CCP
; only t
CCP
shown in Figure 11
10
MHz
t
CDS
CDATA setup
To CCLK rising
10
ns
t
CDH
CDATA hold
From CCLK rising
10
ns
t
CLS
CLATCH setup
To CCLK rising
10
ns
t
CLH
CLATCH hold
From CCLK falling
10
ns
t
CLHIGH
CLATCH high
Not shown in Figure 11
10 ns
t
COE
COUT enable
From CCLK falling
30
ns
t
COD
COUT delay
From CCLK falling
30
ns
t
COH
COUT hold
From CCLK falling, not shown in Figure 11
30 ns
t
COTS
COUT tri-state
From CCLK falling
30
ns
DAC SERIAL PORT
See Figure 24
t
DBH
DBCLK high
Slave mode
10
ns
t
DBL
DBCLK low
Slave mode
10
ns
t
DLS
DLRCLK setup
To DBCLK rising, slave mode
10
ns
t
DLH
DLRCLK hold
From DBCLK rising, slave mode
5
ns
t
DLS
DLRCLK skew
From DBCLK falling, master mode
-8
+8
ns
t
DDS
DSDATA setup
To DBCLK rising
10
ns
t
DDH
DSDATA hold
From DBCLK rising
5
ns
ADC SERIAL PORT
See Figure 25
t
ABH
ABCLK high
Slave mode
10
ns
t
ABL
ABCLK low
Slave mode
10
ns
t
ALS
ALRCLK setup
To ABCLK rising, slave mode
10
ns
t
ALH
ALRCLK hold
From ABCLK rising, slave mode
5
ns
t
ALS
ALRCLK skew
From ABCLK falling, master mode
-8
+8
ns
t
ABDD
ASDATA delay
From ABCLK falling
18
ns
AUXILIARY INTERFACE
t
AXDS
AAUXDATA setup
To AUXBCLK rising
10
ns
t
AXDH
AAUXDATA hold
From AUXBCLK rising
5
ns
t
DXDD
DAUXDATA delay
From AUXBCLK falling
18
ns
t
XBH
AUXBCLK high
10
ns
t
XBL
AUXBCLK low
10
ns
t
DLS
AUXLRCLK setup
To AUXBCLK rising
10
ns
t
DLH
AUXLRCLK hold
From AUXBCLK rising
5
ns
AD1939
Rev. 0 | Page 8 of 32
ABSOLUTE MAXIMUM RATINGS
Table 8.
Parameter Rating
Analog (AVDD)
-0.3 V to +3.6 V
Digital (DVDD)
-0.3 V to +3.6 V
VSUPPLY
-0.3 V to +6.0 V
Input Current (Except Supply Pins)
20 mA
Analog Input Voltage (Signal Pins)
0.3 V to AVDD + 0.3 V
Digital Input Voltage (Signal Pins)
-0.3 V to DVDD + 0.3 V
Operating Temperature Range (Case)
-40C to +125C
Storage Temperature Range
-65C to +150C
Stresses above those listed under the Absolute Maximum
Ratings may cause permanent damage to the device. This is a
stress rating only; functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
THERMAL RESISTANCE
JA
represents thermal resistance, junction-to-ambient;
JC
represents the thermal resistance, junction-to-case.
All characteristics are for a 4-layer board.
Table 9. Thermal Resistance
Package Type
JA
JC
Unit
64-lead LQFP
47
11.1
C/W
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
AD1939
Rev. 0 | Page 9 of 32
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
NC
64
NC
63
AV
DD
62
LF
61
ADC2RN
60
ADC2RP
59
ADC2L
N
58
ADC2L
P
57
ADC1RN
56
ADC1RP
55
ADC1L
N
54
ADC1L
P
53
CM
52
AV
DD
51
NC
50
NC
49
DV
D
D
17
DS
DA
T
A3
18
DS
DA
T
A2
19
DS
DA
T
A1
20
D
BCL
K
21
D
L
RCL
K
22
VS
U
P
PL
Y
23
V
SEN
S
E
24
V
DRI
V
E
25
AS
DA
T
A2
26
AS
DA
T
A1
27
A
BCL
K
28
A
L
RCL
K
29
CI
N/
ADR0
30
CO
UT
/
S
D
A
31
DV
D
D
32
AGND
1
MCLKI/XI
2
MCLKO/XO
3
AGND
4
AVDD
5
OL3P
6
OL3N
7
OR3P
8
OR3N
9
OL4P
10
OL4N
11
OR4P
12
OR4N
13
PD/RST
14
DSDATA4
15
DGND
16
AGND
48
FILTR
47
AGND
46
AVDD
45
AGND
44
OR2N
43
OR2P
42
OL2N
41
OL2P
40
OR1N
39
OR1P
38
OL1P
36
CLATCH/ADR1
35
CCLK/SCL
34
DGND
33
OL1N
37
AD1939
TOP VIEW
(Not to Scale)
DIFFERENTIAL
OUTPUT
NC = NO CONNECT
06
07
1-
0
21
Figure 2. 64-Lead LQFP, Differential Output, Pin Configuration
Table 10. Pin Function Descriptions
Pin No.
In/Out
Mnemonic
Description
1 I AGND
Analog
Ground.
2
I
MCLKI/XI
Master Clock Input/Crystal Oscillator Input.
3
O
MCLKO/XO
Master Clock Output/Crystal Oscillator Output.
4 I AGND
Analog
Ground.
5
I
AVDD
Analog Power Supply. Connect to analog 3.3 V supply.
6
O
OL3P
DAC 3 Left Positive Output.
7
O
OL3N
DAC 3 Left Negative Output.
8
O
OR3P
DAC 3 Right Positive Output.
9
O
OR3N
DAC 3 Right Negative Output.
10
O
OL4P
DAC 4 Left Positive Output.
11
O
OL4N
DAC 4 Left Negative Output.
12
O
OR4P
DAC 4 Right Positive Output.
13
O
OR4N
DAC 4 Right Negative Output
14 I PD/RST
Power-Down Reset (Active Low).
15
I/O
DSDATA4
DAC Input 4 (Input to DAC 4 L and R)/DAC TDM Data Out 2/AUX ADC 1 Data In.
16 I DGND
Digital
Ground.
17
I
DVDD
Digital Power Supply. Connect to digital 3.3 V supply.
18
I/O
DSDATA3
DAC Input 3 (Input to DAC 3 L and R)/DAC TDM Data In 2/Aux DAC 2 Data Output.
19
I/O
DSDATA2
DAC Input 2 (Input to DAC 2 L and R)/DAC TDM Data Out 1/AUX ADC 1 Data In.
20
I
DSDATA1
DAC Input 1 (Input to DAC 1 L and R)/DAC TDM Data In 1/AUX ADC 2 Data In.
21
I/O
DBCLK
Bit Clock for DACs.
22
I/O
DLRCLK
LR Clock for DACs.
23
I
VSUPPLY
+5 V Input to Regulator, Emitter of Pass Transistor.
24
I
VSENSE
+3.3 V Output of Regulator, Collector of Pass Transistor.
AD1939
Rev. 0 | Page 10 of 32
Pin No.
In/Out
Mnemonic
Description
25
O
VDRIVE
Drive for Base of Pass Transistor.
26
I/O
ASDATA2
ADC Serial Data Output 2 (ADC 2 L and R)/ADC TDM Data Input/Aux DAC 1 Data Output.
27
O
ASDATA1
ADC Serial Data Output 1 (ADC 1 L and R)/ADC TDM Data Output.
28
I/O
ABCLK
Bit Clock for ADCs.
29
I/O
ALRCLK
LR Clock for ADCs.
30
I
CIN/ADR0
Control Data Input (SPI).
31
I/O
COUT/SDA
Control Data Output (SPI).
32
I
DVDD
Digital Power Supply. Connect to digital 3.3 V supply.
33 I DGND
Digital
Ground.
34
I
CCLK/SCL
Control Clock Input (SPI).
35 I CLATCH/ADR1
Latch Input for Control Data (SPI).
36
O
OL1P
DAC 1 Left Positive Output.
37
O
OL1N
DAC 1 Left Negative Output.
38
O
OR1P
DAC 1 Right Positive Output.
39
O
OR1N
DAC 1 Right Negative Output.
40
O
OL2P
DAC 2 Left Positive Output.
41
O
OL2N
DAC 2 Left Negative Output.
42
O
OR2P
DAC 2 Right Positive Output.
43
O
OR2N
DAC 2 Right Negative Output
44 I AGND
Analog
Ground.
45
I
AVDD
Analog Power Supply. Connect to analog 3.3 V supply.
46 I AGND
Analog
Ground.
47
O
FILTR
Voltage Reference Filter Capacitor Connection. Bypass with 10 F||100 nF to AGND.
48 I AGND
Analog
Ground.
49 NC
No
Connect.
50 NC
No
Connect.
51
I
AVDD
Analog Power Supply. Connect to analog 3.3 V supply.
52 O CM
Common-Mode Reference Filter Capacitor Connection. Bypass with
47 F||100 nF to AGND.
53
I
ADC1LP
ADC1 Left Positive Input.
54
I
ADC1LN
ADC1 Left Negative Input.
55
I
ADC1RP
ADC1 Right Positive Input.
56
I
ADC1RN
ADC1 Right Negative Input.
57
I
ADC2LP
ADC2 Left Positive Input.
58
I
ADC2LN
ADC2 Left Negative Input.
59
I
ADC2RP
ADC2 Right Positive Input.
60
I
ADC2RN
ADC2 Right Negative Input.
61
O
LF
PLL Loop Filter, Return to AVDD.
62
I
AVDD
Analog Power Supply. Connect to analog 3.3 V supply.
63 NC
No
Connect.
64 NC
No
Connect.
AD1939
Rev. 0 | Page 11 of 32
8
TYPICAL PERFORMANCE CHARACTERISTICS
0.10
0.08
0.06
0.04
0.02
0
0.10
0.08
0.06
0.04
0.02
0
1
16
14
12
10
8
6
4
2
M
AG
NI
T
UD
E
(
d
B)
FREQUENCY (kHz)
06
07
1-
00
2
Figure 3. ADC Pass-Band Filter Response, 48 kHz
0
10
20
30
40
50
60
70
80
90
100
0
4
5
10
15
20
25
30
35
M
AG
NI
T
UDE
(
d
B)
FREQUENCY (kHz)
0
06
07
1
-
00
3
Figure 4. ADC Stop-Band Filter Response, 48 kHz
0.06
0.04
0.02
0.06
0.04
0.02
0
0
24
16
8
M
AG
N
I
T
UDE
(
d
B)
FREQUENCY (kHz)
06
07
1-
0
04
Figure 5. DAC Pass-Band Filter Response, 48 kHz
0
150
100
50
0
4
12
24
36
M
AG
NI
T
UDE
(
d
B)
FREQUENCY (kHz)
8
06
07
1-
005
Figure 6. DAC Stop-Band Filter Response, 48 kHz
0.10
0.10
0.05
0
0.05
0
9
72
48
24
M
AG
N
I
T
UDE
(
d
B)
FREQUENCY (kHz)
6
06
07
1-
0
06
Figure 7. DAC Pass-Band Filter Response, 96 kHz
0
150
100
50
0
96
24
48
72
M
AG
NI
T
UDE
(
d
B)
FREQUENCY (kHz)
06
07
1-
007
Figure 8. DAC Stop-Band Filter Response, 96 kHz
AD1939
Rev. 0 | Page 12 of 32
0.5
0.5
0.4
0.3
0.2
0.1
0
0.1
0.2
0.3
0.4
0
6
8
16
32
M
A
G
N
I
T
UDE
(
d
B)
FREQUENCY (kHz)
4
06
07
1-
0
08
Figure 9. DAC Pass-Band Filter Response, 192 kHz
10
8
6
4
2
0
48
96
64
80
M
AG
NI
T
UDE
(
d
B)
FREQUENCY (kHz)
06
07
1-
009
Figure 10. DAC Stop-Band Filter Response, 192 kHz
AD1939
Rev. 0 | Page 13 of 32
THEORY OF OPERATION
ANALOG-TO-DIGITAL CONVERTERS (ADCS)
There are four analog-to-digital converter (ADC) channels in
the AD1939 configured as two stereo pairs with differential
inputs. The ADCs can operate at a nominal sample rate of 48 kHz,
96 kHz, or 192 kHz. The ADCs include on-board digital anti-
aliasing filters with 79 dB stop-band attenuation and linear
phase response, operating at an oversampling ratio of 128
(48 kHz, 96 kHz, and 192 kHz modes). Digital outputs are
supplied through two serial data output pins (one for each
stereo pair) and a common frame clock (ALRCLK) and bit
clock (ABCLK). Alternatively, one of the TDM modes can be
used to access up to 16 channels on a single TDM data line.
The ADCs must be driven from a differential signal source for
best performance. The input pins of the ADCs connect to internal
switched capacitors. To isolate the external driving op amp from
the glitches caused by the internal switched capacitors, each in-
put pin should be isolated by using a series-connected external
100 resistor together with a 1 nF capacitor connected from
each input to ground. This capacitor must be of high quality, for
example, ceramic NPO or polypropylene film.
The differential inputs have a nominal common-mode voltage
of 1.5 V. The voltage at the common-mode reference pin (CM)
can be used to bias external op amps to buffer the input signals
(see the Power Supply and Voltage Reference section). The
inputs can also be ac-coupled and do not need an external dc
bias to CM.
A digital high-pass filter can be switched in line with the ADCs
under serial control to remove residual dc offsets. It has a 1.4 Hz,
6 dB per octave cutoff at a 48 kHz sample rate. The cutoff fre-
quency scales directly with sample frequency.
DIGITAL-TO-ANALOG CONVERTERS (DACS)
The AD1939 digital-to-analog converter (DAC) channels are
arranged as differential, four stereo pairs giving eight analog
outputs for improved noise and distortion performance. The
DACs include on-board digital reconstruction filters with 70 dB
stop-band attenuation and linear phase response, operating at an
oversampling ratio of 4 (48 kHz or 96 kHz modes) or 2 (192 kHz
mode). Each channel has its own independently programmable
attenuator, adjustable in 255 steps in increments of 0.375 dB.
Digital inputs are supplied through four serial data input pins
(one for each stereo pair) and a common frame clock (DLRCLK)
and bit clock (DBCLK). Alternatively, one of the TDM modes can
be used to access up to 16 channels on a single TDM data line.
Each output pin has a nominal common-mode dc level of 1.5 V
and swings 1.27 V for a 0 dBFS digital input signal. A single op
amp, third-order, external, low-pass filter is recommended to
remove high frequency noise present on the output pins, as well
as to provide differential-to-single-ended conversion in the case
of the differential output. Note that the use of op amps with low
slew rate or low bandwidth can cause high frequency noise and
tones to fold down into the audio band; exercise care in
selecting these components.
The voltage at CM, the common-mode reference pin, can be
used to bias the external op amps that buffer the output signals
(see the Power Supply and Voltage Reference section).
CLOCK SIGNALS
The on-chip phase locked loop (PLL) can be selected to
reference the input sample rate from either of the LRCLK pins
or 256, 384, 512, or 768 times the sample rate, referenced to the
48 kHz mode from the MCLKI/XI pin. The default at power-up
is 256 f
S
from MCLKI/XI. In 96 kHz mode, the master clock
frequency stays at the same absolute frequency; therefore, the
actual multiplication rate is divided by 2. In 192 kHz mode,
the actual multiplication rate is divided by 4. For example, if a
device in the AD1939 family is programmed in 256 f
S
mode, the
frequency of the master clock input is 256 48 kHz = 12.288 MHz.
If the AD1939 is then switched to 96 kHz operation (by writing
to the SPI or I
2
C port), the frequency of the master clock
should remain at 12.288 MHz, which is 128 f
S
in this example.
In 192 kHz mode, this becomes 64 f
S
.
The internal clock for the ADCs is 256 f
S
for all clock modes.
The internal clock for the DACs varies by mode: 512 f
S
(48 kHz
mode), 256 f
S
(96 kHz mode), or 128 f
S
(192 kHz mode). By
default, the on-board PLL generates this internal master clock
from an external clock. A direct 512 f
S
(referenced to 48 kHz
mode) master clock can be used for either the ADCs or DACs if
selected in PLL and Clock Control 1 register.
Note that it is not possible to use a direct clock for the ADCs set
to the 192 kHz mode. It is required that the on-chip PLL be
used in this mode.
The PLL can be powered down in the PLL and Clock Control 0
register. To ensure reliable locking when changing PLL modes,
or if the reference clock is unstable at power-on, power down
the PLL and then power it back up when the reference clock has
stabilized.
The internal master clock (MCLK) can be disabled in the PLL
and Clock Control 0 register to reduce power dissipation when
the AD1939 is idle. The clock should be stable before it is
enabled. Unless a standalone mode is selected (see the Serial
Control Port section), the clock is disabled by reset and must be
enabled by writing to the SPI or I
2
C port for normal operation.
To maintain the highest performance possible, it is recommended
that the clock jitter of the internal master clock signal be limited
to less than 300 ps rms TIE (time interval error). Even at these
levels, extra noise or tones can appear in the DAC outputs if the
jitter spectrum contains large spectral peaks. If the internal PLL
is not being used, it is best to use an independent crystal oscillator
AD1939
Rev. 0 | Page 14 of 32
to generate the master clock. In addition, it is especially
important that the clock signal should not be passed through an
FPGA, CPLD, or other large digital chip (such as a DSP) before
being applied to the AD1939. In most cases, this induces clock
jitter due to the sharing of common power and ground
connections with other unrelated digital output signals. When
the PLL is used, jitter in the reference clock is attenuated above
a certain frequency depending on the loop filter.
RESET AND POWER-DOWN
Reset sets all the control registers to their default settings. To
avoid pops, reset does not power down the analog outputs.
After reset is deasserted and the PLL acquires lock condition,
an initialization routine runs inside the AD1939. This
initialization lasts for approximately 256 MCLKs.
The power-down bits in the PLL and Clock Control 0, DAC
Control 1, and ADC Control 1 registers power down the
respective sections. All other register settings are retained. The
reset pin should be pulled low by an external resistor to
guarantee proper startup.
SERIAL CONTROL PORT
The AD1939 has an SPI control port that permits programming
and reading back of the internal control registers for the ADCs,
DACs, and clock system. A standalone mode is also available for
operation without serial control; it is configured at reset using the
serial control pins. All registers are set to default, except the
internal MCLK enable is set to 1 and ADC BCLK and LRCLK
master/slave is set by the COUT/SDA pin. Standalone mode
only supports stereo mode with an I
2
S data format and 256 f
S
MCLK rate. Refer to Table 11 for details. It is recommended to
use a weak pull-up resistor on CLATCH in applications that
have a microcontroller. This pull-up resistor ensures that the
AD1939 recognizes the presence of a microcontroller.
The SPI control port of the AD1939 is a 4-wire serial control
port. The format is similar to the Motorola SPI format except
the input data-word is 24 bits wide. The serial bit clock and
latch can be completely asynchronous to the sample rate of the
ADCs and DACs. Figure 11 shows the format of the SPI signal.
The first byte is a global address with a read/write bit. For the
AD1939 the address is 0x04, shifted left one bit due to the R/W
bit. The second byte is the AD1939 register address and the
third byte is the data.
Table 11. Standalone Mode Selection
ADC Clocks
CIN/ADR0
COUT/SDA
CCLK/SCL
CLATCH/ADR1
Slave 0 0
0 0
Master 0
1
0 0
D0
D0
D8
D8
D22
D23
D9
D9
CLATCH
CCLK
CIN
COUT
t
CCH
t
CCL
t
CDS
t
CDH
t
CLS
t
CCP
t
CLH
t
COTS
t
COD
t
COE
06
07
1-
0
10
Figure 11. Format of SPI Signal
AD1939
Rev. 0 | Page 15 of 32
POWER SUPPLY AND VOLTAGE REFERENCE
The AD1939 is designed for 3.3 V supplies. Separate power
supply pins are provided for the analog and digital sections.
To minimize noise pickup, these pins should be bypassed with
100 nF ceramic chip capacitors placed as close to the pins as
possible. A bulk aluminum electrolytic capacitor of at least
22 F should also be provided on the same PC board as the
codec. For critical applications, improved performance is
obtained with separate supplies for the analog and digital sections.
If this is not possible, it is recommended that the analog and
digital supplies be isolated by means of a ferrite bead in series
with each supply. It is important that the analog supply be as
clean as possible.
The AD1939 includes a 3.3 V regulator driver that only requires
an external pass transistor and bypass capacitors to make a 5 V
to 3.3 V regulator. If the regulator driver is not used, connect
VSUPPLY, VDRIVE, and VSENSE to DGND.
All digital inputs are compatible with TTL and CMOS levels.
All outputs are driven from the 3.3 V DVDD supply and are
compatible with TTL and 3.3 V CMOS levels.
The ADC and DAC internal voltage reference (V
REF
) is brought
out on FILTR and should be bypassed as close as possible to the
chip with a parallel combination of 10 F and 100 nF. Any
external current drawn should be limited to less than 50 A.
The internal reference can be disabled in the PLL and Clock
Control 1 register and FILTR can be driven from an external
source. This can be used to scale the DAC output to the clipping
level of a power amplifier based on its power supply voltage.
The ADC input gain varies by the inverse ratio. The total gain
from ADC input to DAC output remains constant.
The CM pin is the internal common-mode reference. It should
be bypassed as close as possible to the chip, with a parallel
combination of 47 F and 100 nF. This voltage can be used to
bias external op amps to the common-mode voltage of the input
and output signal pins. The output current should be limited to
less than 0.5 mA source and 2 mA sink.
SERIAL DATA PORTS--DATA FORMAT
The eight DAC channels use a common serial bit clock (DBCLK)
and a common left-right framing clock (DLRCLK) in the serial
data port. The four ADC channels use a common serial bit
clock (ABCLK) and left-right framing clock (ALRCLK) in the
serial data port. The clock signals are all synchronous with the
sample rate. The normal stereo serial modes are shown in
Figure 23.
The ADC and DAC serial data modes default to I
2
S. The ports
can also be programmed for left-justified, right-justified, and
TDM modes. The word width is 24 bits by default and can be
programmed for 16 or 20 bits. The DAC serial formats are
programmable according to the DAC Control 0 register. The
polarity of DBCLK and DLRCLK is programmable according to
the DAC Control 1 register. The ADC serial formats and serial
clock polarity are programmable according to the ADC Control 1
register. Both DAC and ADC serial ports are programmable to
become the bus masters according to DAC Control 1 register
and ADC Control 2 register. By default, both ADC and DAC
serial ports are in the slave mode.
TIME-DIVISION MULTIPLEXED (TDM) MODES
The AD1939 serial ports also have several different TDM serial
data modes. The first and most commonly used configurations
are shown in Figure 12 and Figure 13. In Figure 12, the ADC
serial port outputs one data stream consisting of four on-chip
ADCs followed by four unused slots. In Figure 13, the eight on-
chip DAC data slots are packed into one TDM stream. In this
mode, both DBCLK and ABCLK are 256 f
S
.
SLOT 1
LEFT 1
SLOT 2
RIGHT 1
SLOT 3
LEFT 2
SLOT 4
RIGHT 2
MSB
MSB1
MSB2
DATA
BCLK
LRCLK
SLOT 5
SLOT 6
SLOT 7
SLOT 8
LRCLK
BCLK
DATA
256 BCLKs
32 BCLKs
060
71-
016
Figure 12. ADC TDM (8-Channel I
2
S Mode)
SLOT 1
LEFT 1
SLOT 2
RIGHT 1
SLOT 3
LEFT 2
SLOT 4
RIGHT 2
MSB
MSB1
MSB2
DATA
BCLK
LRCLK
SLOT 5
LEFT 3
SLOT 6
RIGHT 3
SLOT 7
LEFT 4
SLOT 8
RIGHT 4
LRCLK
BCLK
DATA
256 BCLKs
32 BCLKs
0
607
1-
0
17
Figure 13. DAC TDM (8-Channel I
2
S Mode)
The I/O pins of the serial ports are defined according to the
serial mode that is selected. For a detailed description of the
function of each pin in TDM and AUX modes, see Table 12.
The AD1939 allows systems with more than eight DAC channels
to be easily configured by the use of an auxiliary serial data port.
The DAC TDM-AUX mode is shown in Figure 14. In this mode,
the AUX channels are the last four slots of the TDM data stream.
These slots are extracted and output to the AUX serial port. It
should be noted that due to the high DBCLK frequency, this mode
is available only in the 48 kHz/44.1 kHz/32 kHz sample rate.
The AD1939 also allows system configurations with more than
four ADC channels as shown in Figure 15 (using 8 ADCs) and
Figure 16 (using 16 ADCs). Again, due to the high ABCLK fre-
quency, this mode is available only in the 48 kHz/44.1 kHz/32 kHz
sample rate.
AD1939
Rev. 0 | Page 16 of 32
Combining the AUX ADC and DAC modes results in a system
configuration of 8 ADCs and 12 DACs. The system, then, con-
sists of two external stereo ADCs, two external stereo DACs,
and one AD1939. This mode is shown in Figure 17 (combined
AUX DAC and ADC modes).
Table 12. Pin Function Changes in TDM and AUX Modes
Mnemonic
Stereo Modes
TDM Modes
AUX Modes
ASDATA1
ADC1 Data Out
ADC TDM Data Out
TDM Data Out
ASDATA2
ADC2 Data Out
ADC TDM Data In
AUX Data Out 1 (to Ext. DAC 1)
DSDATA1
DAC1 Data In
DAC TDM Data In
TDM Data In
DSDATA2
DAC2 Data In
DAC TDM Data Out
AUX Data In 1 (from Ext. ADC 1)
DSDATA3
DAC3 Data In
DAC TDM Data In 2 (Dual-Line Mode)
AUX Data In 2 (from Ext. ADC 2)
DSDATA4
DAC4 Data In
DAC TDM Data Out 2 (Dual-Line Mode)
AUX Data Out 2 (to Ext. DAC 2)
ALRCLK
ADC LRCLK In/Out
ADC TDM Frame Sync In/Out
TDM Frame Sync In/Out
ABCLK
ADC BCLK In/Out
ADC TDM BCLK In/Out
TDM BCLK In/Out
DLRCLK
DAC LRCLK In/Out
DAC TDM Frame Sync In/Out
AUX LRCLK In/Out
DBCLK
DAC BCLK In/Out
DAC TDM BCLK In/Out
AUX BCLK In/Out
LEFT
RIGHT
MSB
MSB
MSB
MSB
ALRCLK
ABCLK
DSDATA1
(TDM_IN)
DLRCLK
(AUX PORT)
DBCLK
(AUX PORT)
ASDATA2
(AUX1_OUT)
DSDATA4
(AUX2_OUT)
MSB
EMPTY
EMPTY
EMPTY
EMPTY
DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4 AUX L1 AUX R1 AUX L2 AUX R2
8-ON-CHIP DAC CHANNELS
AUXILIARY DAC CHANNELS
WILL APPEAR AT
AUX DAC PORTS
UNUSED SLOTS
32 BITS
0
60
71
-
051
Figure 14. 16-Channel DAC TDM-AUX Mode
AD1939
Rev. 0 | Page 17 of 32
ALRCLK
ABCLK
DSDATA1
(TDM_IN)
ASDATA1
(TDM_OUT)
DLRCLK
(AUX PORT)
DBCLK
(AUX PORT)
DSDATA2
(AUX1_IN)
DSDATA3
(AUX2_IN)
DAC L1
DAC R1
DAC L2
DAC R2
DAC L3
DAC R3
DAC L4
DAC R4
ADC L1
ADC R1
ADC L2
ADC R2
AUX L1
AUX R1
AUX L2
AUX R2
8-ON-CHIP DAC CHANNELS
4-ON-CHIP ADC CHANNELS
4-AUX ADC CHANNELS
32 BITS
LEFT
RIGHT
MSB
MSB
MSB
MSB
MSB
0
60
71
-
0
50
Figure 15. 8-Channel AUX ADC Mode
LEFT
RIGHT
MSB
MSB
MSB
MSB
DLRCLK
(AUX PORT)
DBCLK
(AUX PORT)
DSDATA2
(AUX1_IN)
DSDATA3
(AUX2_IN)
ALRCLK
ABCLK
ASDATA1
(TDM_OUT)
MSB
ADC L1 ADC R1 ADC L2 ADC R2 AUX L1 AUX R1 AUX L2 AUX R2
UNUSED UNUSED UNUSED UNUSED
UNUSED UNUSED UNUSED UNUSED
4-ON-CHIP ADC CHANNELS
AUXILIARY ADC CHANNELS
UNUSED SLOTS
32 BITS
06
07
1-
0
52
Figure 16. 16-Channel AUX ADC Mode
AD1939
Rev. 0 | Page 18 of 32
LEFT
RIGHT
DLRCLK
(AUX PORT)
DBCLK
(AUX PORT)
MSB
MSB
DSDATA2
(AUX1_IN)
MSB
MSB
DSDATA3
(AUX2_IN)
MSB
MSB
ASDATA2
(AUX1_OUT)
MSB
MSB
DSDATA4
(AUX2_OUT)
ALRCLK
ABCLK
DSDATA1
(TDM_IN)
EMPTY
EMPTY
EMPTY
EMPTY
DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4 AUX L1 AUX R1 AUX L2 AUX R2
8-ON-CHIP DAC CHANNELS
AUXILIARY DAC CHANNELS
WILL APPEAR AT
AUX DAC PORTS
UNUSED SLOTS
ASDATA1
(TDM_OUT)
ADC L1 ADC R1 ADC L2 ADC R2
AUX L1 AUX R1 AUX L2 AUX R2
UNUSED UNUSED UNUSED UNUSED
UNUSED UNUSED UNUSED UNUSED
4-ON-CHIP ADC CHANNELS
AUXILIARY ADC CHANNELS
UNUSED SLOTS
0
60
71
-
0
53
Figure 17. Combined AUX DAC and ADC Mode
AD1939
Rev. 0 | Page 19 of 32
DAISY-CHAIN MODE
The AD1939 also allows a daisy-chain configuration to expand
the system to 8 ADCs and 16 DACs (see Figure 18). In this
mode, the DBCLK frequency is 512 f
S
. The first eight slots of the
DAC TDM data stream belong to the first AD1939 in the chain
and the last eight slots belong to the second AD1939. The second
AD1939 is the device attached to the DSP TDM port.
To accommodate 16 channels at a 96 kHz sample rate, the
AD1939 can be configured into a dual-line, TDM mode as
shown in Figure 19. This mode allows a slower DBCLK than
normally required by the one-line TDM mode.
Again, the first four channels of each TDM input belong to the
first AD1939 in the chain and the last four channels belong to
the second AD1939.
The dual-line TDM mode can also be used to send data at a
192 kHz sample rate into the AD1939 as shown in Figure 20.
There are two configurations for the ADC port to work in
daisy-chain mode. The first one is with an ABCLK at 256 f
S
shown in Figure 21. The second configuration is shown in
Figure 22. Note that in the 512 f
S
ABCLK mode, the ADC
channels occupy the first eight slots; the second eight slots are
empty. The TDM_IN of the first AD1939 must be grounded in
all modes of operation.
The I/O pins of the serial ports are defined according to the
serial mode selected. See Table 13 for a detailed description of
the function of each pin. See Figure 26 for a typical AD1939
configuration with two external stereo DACs and two external
stereo ADCs.
Figure 23 through Figure 25 show the serial mode formats. For
maximum flexibility, the polarity of LRCLK and BCLK are
programmable. In these figures, all of the clocks are shown with
their normal polarity. The default mode is I
2
S.
DLRCLK
DBCLK
8 DAC CHANNELS OF THE FIRST IC IN THE CHAIN
8 UNUSED SLOTS
8 DAC CHANNELS OF THE SECOND IC IN THE CHAIN
MSB
DSDATA1 (TDM_IN)
OF THE SECOND AD1939
DSDATA2 (TDM_OUT)
OF THE SECOND AD1939
THIS IS THE TDM
TO THE FIRST AD1939
DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4 DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4
DAC L1 DAC R1 DAC L2 DAC R2 DAC L3 DAC R3 DAC L4 DAC R4
32 BITS
DSP
SECOND
AD1939
FIRST
AD1939
06
07
1-
0
54
Figure 18. Single-Line DAC TDM Daisy-Chain Mode (Applicable to 48 kHz Sample Rate, 16-Channel, Two-AD1939 Daisy Chain)
AD1939
Rev. 0 | Page 20 of 32
06
07
1-
05
5
DLRCLK
DBCLK
8 DAC CHANNELS OF THE SECOND IC IN THE CHAIN
8 DAC CHANNELS OF THE FIRST IC IN THE CHAIN
DSDATA1
(IN)
DAC L1
DAC R1
DAC L2
DAC R2
DAC L1
DAC R1
DAC L2
DAC R2
DSDATA3
(IN)
DAC L3
DAC R3
DAC L4
DAC R4
DAC L3
DAC R3
DAC L4
DAC R4
DSDATA2
(OUT)
DAC L1
DAC R1
DAC L2
DAC R2
DSDATA4
(OUT)
DAC L3
DAC R3
DAC L4
DAC R4
32 BITS
DSP
SECOND
AD1939
FIRST
AD1939
MSB
Figure 19. Dual-Line DAC TDM Mode (Applicable to 96 kHz Sample Rate, 16-Channel, Two-AD1939 Daisy Chain); DSDATA3 and DSDATA4 Are the Daisy Chain
DLRCLK
DBCLK
DSDATA1
DAC L1
DAC R1
DAC L2
DAC R2
DSDATA2
DAC L3
DAC R3
DAC L4
DAC R4
32 BITS
MSB
06
07
1-
0
58
Figure 20. Dual-Line DAC TDM Mode (Applicable to 192 kHz Sample Rate, 8-Channel Mode)
ALRCLK
ABCLK
ASDATA2 (TDM_IN
OF THE SECOND AD1939
IN THE CHAIN)
ADC L1
ADC R1
ADC L2
ADC R2
4 ADC CHANNELS OF FIRST IC IN THE CHAIN
4 ADC CHANNELS OF SECOND IC IN THE CHAIN
ASDATA1 (TDM_OUT
OF THE SECOND AD1939
IN THE CHAIN)
ADC L1
ADC R1
ADC L2
ADC R2
ADC L1
ADC R1
ADC L2
ADC R2
32 BITS
MSB
DSP
SECOND
AD1939
FIRST
AD1939
06
07
1-
05
6
Figure 21. ADC TDM Daisy-Chain Mode (256 f
S
ABCLK, Two-AD1939 Daisy Chain)
AD1939
Rev. 0 | Page 21 of 32
ALRCLK
ABCLK
4 ADC CHANNELS OF
SECOND IC IN THE CHAIN
4 ADC CHANNELS OF
FIRST IC IN THE CHAIN
ADC L1 ADC R1 ADC L2 ADC R2 ADC L1 ADC R1 ADC L2 ADC R2
ASDATA1 (TDM_OUT
OF THE SECOND AD1939
IN THE CHAIN)
ADC L1 ADC R1 ADC L2 ADC R2
ASDATA2 (TDM_IN
OF THE SECOND AD1939
IN THE CHAIN)
32 BITS
MSB
DSP
SECOND
AD1939
FIRST
AD1939
06
07
1-
05
7
Figure 22. ADC TDM Daisy-Chain Mode (512 f
S
ABCLK, Two-AD1939 Daisy Chain)
LRCLK
BCLK
SDATA
LRCLK
BCLK
SDATA
LRCLK
BCLK
SDATA
LSB
LSB
LSB
LSB
LSB
LSB
LEFT CHANNEL
RIGHT CHANNEL
RIGHT CHANNEL
LEFT CHANNEL
LEFT CHANNEL
RIGHT CHANNEL
MSB
MSB
MSB
MSB
MSB
MSB
RIGHT-JUSTIFIED MODE--SELECT NUMBER OF BITS PER CHANNEL
DSP MODE--16 BITS TO 24 BITS PER CHANNEL
I
2
S MODE--16 BITS TO 24 BITS PER CHANNEL
LEFT-JUSTIFIED MODE--16 BITS TO 24 BITS PER CHANNEL
LRCLK
BCLK
SDATA
LSB
LSB
NOTES
1. DSP MODE DOES NOT IDENTIFY CHANNEL.
2. LRCLK NORMALLY OPERATES AT
f
S
EXCEPT FOR DSP MODE, WHICH IS 2
f
S
.
3. BCLK FREQUENCY IS NORMALLY 64 LRCLK BUT MAY BE OPERATED IN BURST MODE.
MSB
MSB
1/
f
S
06
07
1-
0
13
Figure 23. Stereo Serial Modes
AD1939
Rev. 0 | Page 22 of 32
DBCLK
DLRCLK
DSDATA
LEFT-JUSTIFIED
MODE
DSDATA
RIGHT-JUSTIFIED
MODE
DSDATA
I
2
S-JUSTIFIED
MODE
t
DLH
t
DBH
t
DBL
t
DLS
t
DDS
MSB
MSB
MSB
LSB
MSB1
t
DDH
t
DDS
t
DDH
t
DDS
t
DDH
t
DDH
t
DDS
06
07
1-
0
14
Figure 24. DAC Serial Timing
ABCLK
ALRCLK
ASDATA
LEFT-JUSTIFIED
MODE
ASDATA
RIGHT-JUSTIFIED
MODE
ASDATA
I
2
S-JUSTIFIED
MODE
t
ABH
LSB
MSB
MSB
MSB
MSB1
t
ABL
t
ALS
t
ABDD
t
ABDD
t
ABDD
t
ALH
0
60
71
-
0
15
Figure 25. ADC Serial Timing
AD1939
Rev. 0 | Page 23 of 32
Table 13. Pin Function Changes in TDM and AUX Modes (Replication of Table 12)
Mnemonic
Stereo Modes
TDM Modes
AUX Modes
ASDATA1
ADC1 Data Out
ADC TDM Data Out
TDM Data Out
ASDATA2
ADC2 Data Out
ADC TDM Data In
AUX Data Out 1 (to Ext. DAC 1)
DSDATA1
DAC1 Data In
DAC TDM Data In
TDM Data In
DSDATA2
DAC2 Data In
DAC TDM Data Out
AUX Data In 1 (from Ext. ADC 1)
DSDATA3
DAC3 Data In
DAC TDM Data In 2 (Dual-Line Mode)
AUX Data In 2 (from Ext. ADC 2)
DSDATA4
DAC4 Data In
DAC TDM Data Out 2 (Dual-Line Mode)
AUX Data Out 2 (to Ext. DAC 2)
ALRCLK
ADC LRCLK In/Out
ADC TDM Frame Sync In/Out
TDM Frame Sync In/Out
ABCLK
ADC BCLK In/Out
ADC TDM BCLK In/Out
TDM BCLK In/Out
DLRCLK
DAC LRCLK In/Out
DAC TDM Frame Sync In/Out
AUX LRCLK In/Out
DBCLK
DAC BCLK In/Out
DAC TDM BCLK In/Out
AUX BCLK In/Out
AUX
ADC 1
LRCLK
BCLK
DATA
MCLK
AUX
ADC 2
LRCLK
BCLK
DATA
MCLK
AUX
DAC 1
AUX
DAC 2
LRCLK
BCLK
DATA
MCLK
LRCLK
BCLK
DATA
MCLK
30MHz
12.288MHz
SHARC IS RUNNING IN SLAVE MODE
(INTERRUPT-DRIVEN)
SHARC
AD1939
TDM MASTER
AUX MASTER
F
S
Y
N
C
-
TD
M (
R
FS
)
RxCL
K
RxDAT
A
Tx
C
L
K
Tx
D
A
TA
T
F
S
(
NC)
ASDATA2
DSDATA4
DBCLK
DLRCLK
DSDATA2
DSDATA3
MCLK
ASDATA1 ALRCLK ABCLK DSDATA1
06
071
-
01
9
Figure 26. Example of AUX Mode Connection to SHARC (AD1939 as TDM Master/AUX Master Shown)
AD1939
Rev. 0 | Page 24 of 32
CONTROL REGISTERS
DEFINITIONS
The format is the same for I
2
C and SPI ports. The global address for the AD1939 is 0x04, shifted left one bit due to the R/W bit. However,
in I
2
C, ADR0 and ADR1 are OR'ed into Bit 17 and Bit 8 to provide multiple chip addressing. All registers are reset to 0, except for the
DAC volume registers that are set to full volume.
Note that the first setting in each control register parameter is the default setting.
Table 14. Register Format
Global
Address
R/W
Register Address
Data
Bit
23:17 16
15:8
7:0
Table 15. Register Addresses and Functions
Address Function
0
PLL and Clock Control 0
1
PLL and Clock Control 1
2
DAC Control 0
3
DAC Control 1
4
DAC Control 2
5
DAC individual channel mutes
6
DAC 1L volume control
7
DAC 1R volume control
8
DAC 2L volume control
9
DAC 2R volume control
10
DAC 3L volume control
11
DAC 3R volume control
12
DAC 4L volume control
13
DAC 4R volume control
14
ADC Control 0
15
ADC Control 1
16
ADC Control 2
PLL AND CLOCK CONTROL REGISTERS
Table 16. PLL and Clock Control 0 Register
Bit Value Function
Description
0
0
Normal operation
PLL power-down
1 Power-down
2:1
00
INPUT 256 (44.1 kHz or 48 kHz)
MCLKI/XI
01
INPUT 384 (44.1 kHz or 48 kHz)
10
INPUT 512 (44.1 kHz or 48 kHz)
11
INPUT 768 (44.1 kHz or 48 kHz)
4:3
00
XTAL oscillator enabled
MCLKO/XO pin
01
256 f
S
VCO output
10
512 f
S
VCO output
11 Off
6:5 00
MCLKI
PLL
input
01 DLRCLK
10 ALRCLK
11 Reserved
7
0
Disable: ADC and DAC idle
Internal master clock enable
1
Enable: ADC and DAC active
AD1939
Rev. 0 | Page 25 of 32
Table 17. PLL and Clock Control 1 Register
Bit Value Function
Description
0
0
PLL clock
DAC clock source select
1
MCLK
1
0
PLL clock
ADC clock source select
1
MCLK
2 0
Enabled
On-chip
voltage
reference
1
Disabled
3
0
Not locked
PLL lock indicator (read only)
1
Locked
7:4 0000
Reserved
DAC CONTROL REGISTERS
Table 18. DAC Control 0 Register
Bit
Value
Function
Description
0 0
Normal
Power-down
1
Power-down
2:1
00
32 kHz/44.1 kHz/48 kHz
Sample rate
01
64 kHz/88.2 kHz/96 kHz
10
128 kHz/176.4 kHz/192 kHz
11
Reserved
5:3
000
1
SDATA delay (BCLK periods)
001 0
010 8
011 12
100 16
101 Reserved
110 Reserved
111 Reserved
7:6
00
Stereo (normal)
Serial format
01
TDM
(daisy
chain)
10
DAC AUX mode (ADC-, DAC-, TDM-coupled)
11
Dual-line
TDM
Table 19. DAC Control 1 Register
Bit Value Function
Description
0
0
Latch in mid cycle (normal)
BCLK active edge (TDM in)
1
Latch in at end of cycle (pipeline)
2:1
00
64 (2 channels)
BCLKs per frame
01
128 (4 channels)
10
256 (8 channels)
11
512 (16 channels)
3
0
Left low
LRCLK polarity
1
Left
high
4 0
Slave
LRCLK
master/slave
1
Master
5 0
Slave
BCLK
master/slave
1
Master
6
0
DBCLK pin
BCLK source
1
Internally
generated
7 0
Normal
BCLK
polarity
1
Inverted
AD1939
Rev. 0 | Page 26 of 32
Table 20. DAC Control 2 Register
Bit Value
Function
Description
0 0
Unmute
Master
mute
1
Mute
2:1
00
Flat
De-emphasis (32 kHz/44.1 kHz/48 kHz mode only)
01
48 kHz curve
10
44.1 kHz curve
11
32 kHz curve
4:3 00
24
Word
width
01
20
10
Reserved
11
16
5
0
Noninverted
DAC output polarity
1
Inverted
7:6 00
Reserved
Table 21. DAC Individual Channel Mutes
Bit Value
Function
Description
0
0
Unmute
DAC 1 left mute
1
Mute
1
0
Unmute
DAC 1 right mute
1
Mute
2
0
Unmute
DAC 2 left mute
1
Mute
3
0
Unmute
DAC 2 right mute
1
Mute
4
0
Unmute
DAC 3 left mute
1
Mute
5
0
Unmute
DAC 3 right mute
1
Mute
6
0
Unmute
DAC 4 left mute
1
Mute
7
0
Unmute
DAC 4 right mute
1
Mute
Table 22. DAC Volume Controls
Bit Value
Function
Description
7:0
0
No attenuation
DAC volume control
1 to 254
-3/8 dB per step
255
Full
attenuation
AD1939
Rev. 0 | Page 27 of 32
ADC CONTROL REGISTERS
Table 23. ADC Control 0 Register
Bit Value
Function
Description
0 0 Normal
Power-down
1
Power
down
1 0 Off
High-pass
filter
1
On
2
0
Unmute
ADC 1L mute
1
Mute
3
0
Unmute
ADC 1R mute
1
Mute
4
0
Unmute
ADC 2L mute
1
Mute
5
0
Unmute
ADC 2R mute
1
Mute
7:6
00
32 kHz/44.1 kHz/48 kHz
Output sample rate
01
64 kHz/88.2 kHz/96 kHz
10
128 kHz/176.4 kHz/192 kHz
11
Reserved
Table 24. ADC Control 1 Register
Bit Value
Function
Description
1:0 00 24
Word
width
01
20
10
Reserved
11
16
4:2
000
1
SDATA delay (BCLK periods)
001
0
010
8
011
12
100
16
101
Reserved
110
Reserved
111
Reserved
6:5 00 Stereo
Serial
format
01
TDM
(daisy
chain)
10
ADC Aux mode (ADC-, DAC, TDM-coupled)
11
Reserved
7
0
Latch in mid cycle (normal)
BCLK active edge (TDM in)
1
Latch in at end of cycle (pipeline)
AD1939
Rev. 0 | Page 28 of 32
Table 25. ADC Control 2 Register
Bit
Value
Function
Description
0
0
50/50 (allows 32-/24-/20-/16-BCLK/channel)
LRCLK format
1
Pulse
(32-BCLK/channel)
1
0
Drive out on falling edge (DEF)
BCLK polarity
1
Drive out on rising edge
2
0
Left low
LRCLK polarity
1
Left
high
3 0
Slave
LRCLK
master/slave
1
Master
5:4
00
64
BCLKs per frame
01
128
10
256
11
512
6 0
Slave
BCLK
master/slave
1
Master
7
0
ABCLK pin
BCLK source
1
Internally
generated
AD1939
Rev. 0 | Page 29 of 32
To relax the requirement for the setup time of the AD1939 in
cases of high speed TDM data transmission, the AD1939 can
latch in the data using the falling edge of DBCLK. This effec-
tively dedicates the entire BCLK period to the setup time. This
mode is useful in cases where the source has a large delay time
in the serial data driver. Figure 28 shows this pipeline mode of
data transmission.
ADDITIONAL MODES
The AD1939 offers several additional modes for board level
design enhancements. To reduce the EMI in board level design,
serial data can be transmitted without an explicit BCLK. See
Figure 27 for an example of a DAC TDM data transmission
mode that does not require high speed DBCLK. This configura-
tion is applicable when the AD1939 master clock is generated
by the PLL with the DLRCLK as the PLL reference frequency.
Both the BCLK-less and pipeline modes are available on the
ADC serial data port.
DLRCLK
INTERNAL
DBCLK
DSDATA
DLRCLK
INTERNAL
DBCLK
TDM-DSDATA
32 BITS
06
07
1-
0
59
Figure 27. Serial DAC Data Transmission in TDM Format Without DBCLK
(Applicable Only If PLL Locks to DLRCLK, This Model Is Also Available in the ADC Serial Data Port)
DLRCLK
DBCLK
DSDATA
DATA MUST BE VALID
AT THIS BCLK EDGE
MSB
0
60
71
-
06
0
Figure 28. I
2
S Pipeline Mode in DAC Serial Data Transmission
(Applicable in Stereo and TDM, Useful for High Frequency TDM Transmission,
This Model Is Also Available in the ADC Serial Data Port)
AD1939
Rev. 0 | Page 30 of 32
APPLICATION CIRCUITS
Typical application circuits are shown in Figure 29 through Figure 32. Figure 29 shows a typical ADC input filter circuit. Recommended
loop filters for LR clock and master clock as the PLL reference are shown in Figure 30. Output filters for the DAC outputs are shown in
Figure 31 and a regulator circuit is shown in Figure 32.
2
1
3
OP275
+
6
7
5
OP275
+
120pF
600Z
AUDIO
INPUT
100pF
120pF
4.7F
+
4.7F
+
100pF
1nF
NPO
1nF
NPO
ADCxN
ADCxP
06071-
023
Figure 29. Typical ADC Input Filter Circuit
39nF
+
2.2nF
LF
LRCLK
AVDD2
5.6nF
390nF
LF
MCLK
AVDD2
06
07
1-
0
27
Figure 30. Recommended Loop Filters for LRCLK or MCLK PLL Reference
2
1
3
OP275
+
2.2nF
NPO
AUDIO
OUTPUT
68pF
NPO
150pF
NPO
560pF
NPO
270pF
NPO
DAC
OUTN
DAC
OUTP
06
07
1-
0
26
Figure 31. Typical DAC Output Filter Circuit (Differential)
10F
+
E
C
B
VSUPPLY
5V
VSENSE
3.3V
FZT953
VDRIVE
100nF
10F
+
100nF
06
07
1-
0
28
Figure 32. Recommended 3.3 V Regulator Circuit
AD1939
Rev. 0 | Page 31 of 32
OUTLINE DIMENSIONS
COMPLIANT TO JEDEC STANDARDS MS-026-BCD
TOP VIEW
(PINS DOWN)
1
16
17
33
32
48
49
64
0.27
0.22
0.17
0.50
BSC
LEAD PITCH
10.00
BSC SQ
12.00
BSC SQ
PIN 1
1.60
MAX
0.75
0.60
0.45
VIEW A
0.20
0.09
1.45
1.40
1.35
0.08 MAX
COPLANARITY
VIEW A
ROTATED 90 CCW
SEATING
PLANE
0.15
0.05
7
3.5
0
Figure 33. 64-Lead Low Profile Quad Flat Package [LQFP]
(ST-64-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model
Temperature Range
Package Description
Package Option
AD1939YSTZ
1 , 2
40C to +105C
64-Lead LQFP
ST-64-2
AD1939YSTZRL
40C to +105C
64-Lead LQFP, 13" Reel
ST-64-2
EVAL-AD1939EB
Evaluation
Board
1
Z = Pb-free part.
2
Differential output, SPI control port.
AD1939
Rev. 0 | Page 32 of 32
NOTES
2006 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06071-0-7/06(0)
PDF 
ZIP