DSP Microcomputer

ADSP-2185L

REV. A

Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.

ICE-Port is a trademark of Analog Devices, Inc.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700

World Wide Web Site: http://www.analog.com

Fax: 781/326-8703

© Analog Devices, Inc., 1998

GENERAL NOTE

This data sheet represents specifications for the ADSP-2185L
3.3 V processor.

GENERAL DESCRIPTION

The ADSP-2185L is a single-chip microcomputer optimized for
digital signal processing (DSP) and other high speed numeric
processing applications.

The ADSP-2185L combines the ADSP-2100 family base archi-
tecture (three computational units, data address generators and
a program sequencer) with two serial ports, a 16-bit internal
DMA port, a byte DMA port, a programmable timer, Flag I/O,
extensive interrupt capabilities and on-chip program and data
memory.

The ADSP-2185L integrates 80K bytes of on-chip memory
configured as 16K words (24-bit) of program RAM, and 16K
words (16-bit) of data RAM. Power-down circuitry is also pro-
vided to meet the low power needs of battery operated portable
equipment. The ADSP-2185L is available in 100-lead LQFP
package.

In addition, the ADSP-2185L supports instructions which
include bit manipulations--bit set, bit clear, bit toggle, bit test--
ALU constants, multiplication instruction (x squared), biased
rounding, result free ALU operations, I/O memory transfers and
global interrupt masking, for increased flexibility.

Fabricated in a high speed, low power, CMOS process, the
ADSP-2185L operates with a 19 ns instruction cycle time. Ev-
ery instruction can execute in a single processor cycle.

FEATURES
PERFORMANCE
19 ns Instruction Cycle Time @ 3.3 Volts, 52 MIPS

Sustained Performance

Single-Cycle Instruction Execution
Single-Cycle Context Switch
3-Bus Architecture Allows Dual Operand Fetches in

Every Instruction Cycle

Multifunction Instructions
Power-Down Mode Featuring Low CMOS Standby

Power Dissipation with 400 Cycle Recovery from
Power-Down Condition

Low Power Dissipation in Idle Mode

INTEGRATION
ADSP-2100 Family Code Compatible, with Instruction

Set Extensions

80K Bytes of On-Chip RAM, Configured as 16K Words

Program Memory RAM and 16K Words
Data Memory RAM

Dual Purpose Program Memory for Instruction and Data

Storage

Independent ALU, Multiplier/Accumulator and Barrel

Shifter Computational Units

Two Independent Data Address Generators
Powerful Program Sequencer Provides Zero Overhead

Looping Conditional Instruction Execution

Programmable 16-Bit Interval Timer with Prescaler
100-Lead LQFP

SYSTEM INTERFACE
16-Bit Internal DMA Port for High Speed Access to

On-Chip Memory (Mode Selectable)

4 MByte Memory Interface for Storage of Data Tables

and Program Overlays (Mode Selectable)

8-Bit DMA to Byte Memory for Transparent Program

and Data Memory Transfers (Mode Selectable)

I/O Memory Interface with 2048 Locations Supports

Parallel Peripherals (Mode Selectable)

Programmable Memory Strobe and Separate I/O Memory

Space Permits "Glueless" System Design

Programmable Wait State Generation
Two Double-Buffered Serial Ports with Companding

Hardware and Automatic Data Buffering

Automatic Booting of On-Chip Program Memory from

Byte-Wide External Memory, e.g., EPROM, or
Through Internal DMA Port

Six External Interrupts
13 Programmable Flag Pins Provide Flexible System

Signaling

UART Emulation through Software SPORT Reconfiguration
ICE-PortTM Emulator Interface Supports Debugging in

Final Systems

FUNCTIONAL BLOCK DIAGRAM

SERIAL PORTS

SPORT 1

SPORT 0

MEMORY

PROGRAMMABLE

I/O

AND

FLAGS

BYTE DMA

CONTROLLER

8K 24 OVERLAY 1
8K 24 OVERLAY 2

TIMER

ADSP-2100 BASE

ARCHITECTURE

SHIFTER

MAC

ALU

ARITHMETIC UNITS

POWER-DOWN

CONTROL

PROGRAM

SEQUENCER

DAG 2

DAG 1

DATA ADDRESS

GENERATORS

PROGRAM MEMORY ADDRESS

DATA MEMORY ADDRESS

PROGRAM MEMORY DATA

DATA MEMORY DATA

EXTERNAL

DATA

BUS

EXTERNAL

ADDRESS

BUS

INTERNAL

DMA

PORT

EXTERNAL

DATA

BUS

FULL MEMORY

MODE

HOST MODE

8K 16 OVERLAY 1
8K 16 OVERLAY 2

(

) (

)

16K 24 PM

16K 16 DM

REV. A

ADSP-2185L

The ADSP-2185L's flexible architecture and comprehensive in-
struction set allow the processor to perform multiple operations
in parallel. In one processor cycle the ADSP-2185L can:

· Generate the next program address
· Fetch the next instruction
· Perform one or two data moves
· Update one or two data address pointers
· Perform a computational operation

This takes place while the processor continues to:

· Receive and transmit data through the two serial ports
· Receive or transmit data through the internal DMA port
· Receive or transmit data through the byte DMA port
· Decrement timer

DEVELOPMENT SYSTEM

The ADSP-2100 Family Development Software, a complete set
of tools for software and hardware system development, sup-
ports the ADSP-2185L. The System Builder provides a high
level method for defining the architecture of systems under de-
velopment. The Assembler has an algebraic syntax that is easy
to program and debug. The Linker combines object files into an
executable file. The Simulator provides an interactive instruc-
tion-level simulation with a reconfigurable user interface to dis-
play different portions of the hardware environment.

A PROM Splitter generates PROM programmer compatible
files. The C Compiler, based on the Free Software Foundation's
GNU C Compiler, generates ADSP-2185L assembly source
code. The source code debugger allows programs to be cor-
rected in the C environment. The Runtime Library includes over
100 ANSI-standard mathematical and DSP-specific functions.

The EZ-KIT Lite is a hardware/software kit offering a complete
development environment for the entire ADSP-21xx family: an
ADSP-218x based evaluation board with PC monitor software
plus Assembler, Linker, Simulator, and PROM Splitter soft-
ware. The ADSP-218x EZ-KIT Lite is a low cost, easy to use
hardware platform on which you can quickly get started with
your DSP software design. The EZ-KIT Lite includes the fol-
lowing features:

· 33 MHz ADSP-218x
· Full 16-bit Stereo Audio I/O with AD1847 SoundPort

Codec

· RS-232 Interface to PC with Windows 3.1 Control Software
· EZ-ICE

Connector for Emulator Control

· DSP Demo Programs

The ADSP-218x EZ-ICE Emulator aids in the hardware debug-
ging of ADSP-2185L system. The emulator consists of hard-
ware, host computer resident software and the target board
connector. The ADSP-2185L integrates on-chip emulation sup-
port with a 14-pin ICE-Port interface. This interface provides a
simpler target board connection requiring fewer mechanical
clearance considerations than other ADSP-2100 Family
EZ-ICEs. The ADSP-2185L device need not be removed from
the target system when using the EZ-ICE, nor are any adapters
needed. Due to the small footprint of the EZ-ICE connector, emu-
lation can be supported in final board designs.

The EZ-ICE performs a full range of functions, including:

· In-target operation
· Up to 20 breakpoints
· Single-step or full-speed operation

· Registers and memory values can be examined and altered
· PC upload and download functions
· Instruction-level emulation of program booting and execution
· Complete assembly and disassembly of instructions
· C source-level debugging

See "Designing An EZ-ICE-Compatible Target System" in the
ADSP-2100 Family EZ-Tools Manual (ADSP-2181 sections) as
well as the Designing an EZ-ICE Compatible System section of
this data sheet for the exact specifications of the EZ-ICE target
board connector.

Additional Information

This data sheet provides a general overview of ADSP-2185L
functionality. For additional information on the architecture and
instruction set of the processor, see the ADSP-2100 Family
User's Manual, Third Edition. For more information about the
development tools, refer to the ADSP-2100 Family Develop-
ment Tools Data Sheet.

ARCHITECTURE OVERVIEW

The ADSP-2185L instruction set provides flexible data moves
and multifunction (one or two data moves with a computation)
instructions. Every instruction can be executed in a single pro-
cessor cycle. The ADSP-2185L assembly language uses an alge-
braic syntax for ease of coding and readability. A comprehensive
set of development tools supports program development.

SERIAL PORTS

SPORT 1

SPORT 0

MEMORY

PROGRAMMABLE

I/O

AND

FLAGS

BYTE DMA

CONTROLLER

8K 24 OVERLAY 1
8K 24 OVERLAY 2

TIMER

ADSP-2100 BASE

ARCHITECTURE

SHIFTER

MAC

ALU

ARITHMETIC UNITS

POWER-DOWN

CONTROL

PROGRAM

SEQUENCER

DAG 2

DAG 1

DATA ADDRESS

GENERATORS

PROGRAM MEMORY ADDRESS

DATA MEMORY ADDRESS

PROGRAM MEMORY DATA

DATA MEMORY DATA

EXTERNAL

DATA

BUS

EXTERNAL

ADDRESS

BUS

INTERNAL

DMA

PORT

EXTERNAL

DATA

BUS

FULL MEMORY

MODE

HOST MODE

8K 16 OVERLAY 1
8K 16 OVERLAY 2

(

) (

)

16K 24 PM

16K 16 DM

Figure 1. Functional Block Diagram

Figure 1 is an overall block diagram of the ADSP-2185L. The
processor contains three independent computational units: the
ALU, the multiplier/accumulator (MAC) and the shifter. The
computational units process 16-bit data directly and have provi-
sions to support multiprecision computations. The ALU per-
forms a standard set of arithmetic and logic operations; division
primitives are also supported. The MAC performs single-cycle
multiply, multiply/add and multiply/subtract operations with
40 bits of accumulation. The shifter performs logical and arith-
metic shifts, normalization, denormalization and derive expo-
nent operations.

The shifter can be used to efficiently implement numeric for-
mat control including multiword and block floating-point
representations.

The internal result (R) bus connects the computational units so
that the output of any unit may be the input of any unit on the
next cycle.

EZ-ICE and SoundPort are registered trademarks of Analog Devices, Inc.

ADSP-2185L

REV. A

A powerful program sequencer and two dedicated data address
generators ensure efficient delivery of operands to these computa-
tional units. The sequencer supports conditional jumps, subroutine
calls and returns in a single cycle. With internal loop counters and
loop stacks, the ADSP-2185L executes looped code with zero over-
head; no explicit jump instructions are required to maintain loops.

Two data address generators (DAGs) provide addresses for
simultaneous dual operand fetches (from data memory and pro-
gram memory). Each DAG maintains and updates four address
pointers. Whenever the pointer is used to access data (indirect
addressing), it is post-modified by the value of one of four pos-
sible modify registers. A length value may be associated with
each pointer to implement automatic modulo addressing for
circular buffers.

Efficient data transfer is achieved with the use of five internal
buses:

· Program Memory Address (PMA) Bus
· Program Memory Data (PMD) Bus
· Data Memory Address (DMA) Bus
· Data Memory Data (DMD) Bus
· Result (R) Bus

The two address buses (PMA and DMA) share a single external
address bus, allowing memory to be expanded off-chip, and the
two data buses (PMD and DMD) share a single external data
bus. Byte memory space and I/O memory space also share the
external buses.

Program memory can store both instructions and data, permit-
ting the ADSP-2185L to fetch two operands in a single cycle,
one from program memory and one from data memory. The
ADSP-2185L can fetch an operand from program memory and
the next instruction in the same cycle.

In lieu of the address and data bus for external memory connec-
tion, the ADSP-2185L may be configured for 16-bit Internal
DMA port (IDMA port) connection to external systems. The
IDMA port is made up of 16 data/address pins and five control
pins. The IDMA port provides transparent, direct access to the
DSPs on-chip program and data RAM.

An interface to low cost byte-wide memory is provided by the
Byte DMA port (BDMA port). The BDMA port is bidirectional
and can directly address up to four megabytes of external RAM
or ROM for off-chip storage of program overlays or data tables.

The byte memory and I/O memory space interface supports slow
memories and I/O memory-mapped peripherals with program-
mable wait state generation. External devices can gain control of
external buses with bus request/grant signals (BR, BGH, and BG).
One execution mode (Go Mode) allows the ADSP-2185L to con-
tinue running from on-chip memory. Normal execution mode re-
quires the processor to halt while buses are granted.

The ADSP-2185L can respond to eleven interrupts. There can
be up to six external interrupts (one edge-sensitive, two level-
sensitive and three configurable) and seven internal interrupts
generated by the timer, the serial ports (SPORTs), the Byte
DMA port and the power-down circuitry. There is also a master
RESET signal. The two serial ports provide a complete synchro-
nous serial interface with optional companding in hardware and a
wide variety of framed or frameless data transmit and receive
modes of operation.

Each port can generate an internal programmable serial clock or
accept an external serial clock.

The ADSP-2185L provides up to 13 general-purpose flag pins.
The data input and output pins on SPORT1 can be alternatively
configured as an input flag and an output flag. In addition, there
are eight flags that are programmable as inputs or outputs and
three flags that are always outputs.

A programmable interval timer generates periodic interrupts. A
16-bit count register (TCOUNT) is decremented every n pro-
cessor cycle, where n is a scaling value stored in an 8-bit register
(TSCALE). When the value of the count register reaches zero,
an interrupt is generated and the count register is reloaded from
a 16-bit period register (TPERIOD).

Serial Ports

The ADSP-2185L incorporates two complete synchronous se-
rial ports (SPORT0 and SPORT1) for serial communications
and multiprocessor communication.

Here is a brief list of the capabilities of the ADSP-2185L
SPORTs. For additional information on Serial Ports, refer to
the ADSP-2100 Family User's Manual, Third Edition.

· SPORTs are bidirectional and have a separate, double-

buffered transmit and receive section.

· SPORTs can use an external serial clock or generate their

own serial clock internally.

· SPORTs have independent framing for the receive and trans-

mit sections. Sections run in a frameless mode or with frame
synchronization signals internally or externally generated.
Frame sync signals are active high or inverted, with either of
two pulsewidths and timings.

· SPORTs support serial data word lengths from 3 to 16 bits

and provide optional A-law and

-law companding according

to CCITT recommendation G.711.

· SPORT receive and transmit sections can generate unique in-

terrupts on completing a data word transfer.

· SPORTs can receive and transmit an entire circular buffer of

data with only one overhead cycle per data word. An interrupt
is generated after a data buffer transfer.

· SPORT0 has a multichannel interface to selectively receive

and transmit a 24- or 32-word, time-division multiplexed,
serial bitstream.

· SPORT1 can be configured to have two external interrupts

(IRQ0 and IRQ1) and the Flag In and Flag Out signals. The
internally generated serial clock may still be used in this
configuration.

PIN DESCRIPTIONS

The ADSP-2185L is available in a 100-lead LQFP package. In
order to maintain maximum functionality and reduce package
size and pin count, some serial port, programmable flag, inter-
rupt and external bus pins have dual, multiplexed functionality.
The external bus pins are configured during RESET only,
while serial port pins are software configurable during program
execution. Flag and interrupt functionality is retained concur-
rently on multiplexed pins. In cases where pin functionality is
reconfigurable, the default state is shown in plain text; alternate
functionality is shown in italics. See Common-Mode Pin
Descriptions.

REV. A

ADSP-2185L

Common-Mode Pin Descriptions

Pin

# of

Input/

Name(s)

Pins Output

Function

RESET

Processor Reset Input

Bus Request Input

Bus Grant Output

BGH

Bus Grant Hung Output

DMS

Data Memory Select Output

PMS

Program Memory Select Output

IOMS

Memory Select Output

BMS

Byte Memory Select Output

CMS

Combined Memory Select Output

Memory Read Enable Output

Memory Write Enable Output

IRQ2/

Edge- or Level-Sensitive Interrupt

PF7

I/O

Request.

Programmable I/O Pin

IRQL1/

Level-Sensitive Interrupt Requests

PF6

I/O

Programmable I/O Pin

IRQL0/

Level-Sensitive Interrupt Requests

PF5

I/O

Programmable I/O Pin

IRQE/

Edge-Sensitive Interrupt Requests

PF4

I/O

Programmable I/O Pin

PF3

I/O

Programmable I/O Pin During
Normal Operation

Mode C/

Mode Select Input--Checked
Only During RESET

PF2

I/O

Programmable I/O Pin During
Normal Operation

Mode B/

Mode Select Input--Checked
Only During RESET

PF1

I/O

Programmable I/O Pin During
Normal Operation

Mode A/

Mode Select Input--Checked
Only During RESET

PF0

I/O

Programmable I/O Pin During
Normal Operation

CLKIN,
XTAL

Clock or Quartz Crystal Input

CLKOUT

Processor Clock Output

SPORT0

I/O

Serial Port I/O Pins

SPORT1

I/O

Serial Port I/O Pins

IRQ1:0

Edge- or Level-Sensitive Interrupts,

FI, FO

Flag In, Flag Out

PWD

Power-Down Control Input

PWDACK 1

Power-Down Control Output

FL0, FL1,
FL2

Output Flags

VDD and
GND

Power and Ground

EZ-Port

I/O

For Emulation Use

OTES

Interrupt/Flag Pins retain both functions concurrently. If IMASK is set to enable the

corresponding interrupts, then the DSP will vector to the appropriate interrupt vec-
tor address when the pin is asserted, either by external devices, or set as a program-
mable flag.

SPORT configuration determined by the DSP System Control Register. Software

configurable.

Memory Interface Pins

The ADSP-2185L processor can be used in one of two modes,
Full Memory Mode, which allows BDMA operation with full
external overlay memory and I/O capability, or Host Mode,
which allows IDMA operation with limited external addressing
capabilities. The operating mode is determined by the state of
the Mode C pin during RESET and cannot be changed while
the processor is running. See tables for Full Memory Mode Pins
and Host Mode Pins for descriptions.

Full Memory Mode Pins (Mode C = 0)

Pin

# of

Input/

Name(s) Pins Output Function

A13:0

Address Output Pins for Program,
Data, Byte and I/O Spaces

D23:0

I/O

Data I/O Pins for Program, Data,
Byte and I/O Spaces (8 MSBs are
also used as Byte Memory addresses)

Host Mode Pins (Mode C = 1)

Pin

# of

Input/

Name(s) Pins Output Function

IAD15:0 16

I/O

IDMA Port Address/Data Bus

Address Pin for External I/O, Pro-
gram, Data or Byte access

D23:8

I/O

Data I/O Pins for Program, Data
Byte and I/O spaces

IWR

IDMA Write Enable

IRD

IDMA Read Enable

IAL

IDMA Address Latch Pin

IDMA Select

IACK

IDMA Port Acknowledge

In Host Mode, external peripheral addresses can be decoded using the A0,
CMS, PMS, DMS and IOMS signals

Terminating Unused Pin

The following table shows the recommendations for terminating
unused pins.

Pin Terminations

I/O

Hi-Z*

Pin

3-State

Reset

Caused

Unused

Name

(Z)

State

Configuration

XTAL

Float

CLKOUT

Float

A13:1 or

O (Z)

Hi-Z

BR, EBR Float

IAD12:0

I/O (Z)

Hi-Z

Float

O (Z)

Hi-Z

BR, EBR Float

D23:8

I/O (Z)

Hi-Z

BR, EBR Float

D7 or

I/O (Z)

Hi-Z

BR, EBR Float

IWR

High (Inactive)

D6 or

I/O (Z)

Hi-Z

BR, EBR Float

IRD

BR, EBR High (Inactive)

D5 or

I/O (Z)

Hi-Z

Float

IAL

Low (Inactive)

ADSP-2185L

REV. A

Pin Terminations (Continued)

I/O

Hi-Z*

Pin

3-State

Reset

Caused

Unused

Name

(Z)

State

Configuration

D4 or

I/O (Z)

Hi-Z

BR, EBR Float

High (Inactive)

D3 or

I/O (Z)

Hi-Z

BR, EBR Float

IACK

Float

D2:0 or

I/O (Z)

Hi-Z

BR, EBR Float

IAD15:13

I/O (Z)

Hi-Z

Float

PMS

O (Z)

BR, EBR

Float

DMS

O (Z)

BR, EBR Float

BMS

O (Z)

BR, EBR Float

IOMS

O (Z)

BR, EBR Float

CMS

O (Z)

BR, EBR Float

O (Z)

BR, EBR Float

O (Z)

BR, EBR Float

High (Inactive)

O (Z)

Float

BGH

Float

IRQ2/PF7

I/O (Z)

Input = High (Inactive)
or Program as Output,
Set to 1, Let Float

IRQL1/PF6 I/O (Z)

Input = High (Inactive)
or Program as Output,
Set to 1, Let Float

IRQL0/PF5 I/O (Z)

Input = High (Inactive)
or Program as Output,
Set to 1, Let Float

IRQE/PF4

I/O (Z)

Input = High (Inactive)
or Program as Output,
Set to 1, Let Float

SCLK0

I/O

Input = High or Low,
Output = Float

RFS0

I/O

High or Low

DR0

High or Low

TFS0

I/O

High or Low

DT0

Float

SCLK1

I/O

Input = High or Low,
Output = Float

RFS1/RQ0

I/O

High or Low

DR1/FI

High or Low

TFS1/RQ1

I/O

High or Low

DT1/FO

Float

EBR

EBG

ERESET

EMS

EINT

ECLK

ELIN

ELOUT

NOTES

*Hi-Z = High Impedance.

1. If the CLKOUT pin is not used, turn it OFF.
2. If the Interrupt/Programmable Flag pins are not used, there are two options:

Option 1: When these pins are configured as INPUTS at reset and function as
interrupts and input flag pins, pull the pins High (inactive).
Option 2: Program the unused pins as OUTPUTS, set them to 1, and let
them float.

3. All bidirectional pins have three-stated outputs. When the pins is configured

as an output, the output is Hi-Z (high impedance) when inactive.

4. CLKIN, RESET, and PF3:0 are not included in the table because these pins

must be used.

Interrupts

The interrupt controller allows the processor to respond to the
eleven possible interrupts and reset with minimum overhead.
The ADSP-2185L provides four dedicated external interrupt
input pins, IRQ2, IRQL0, IRQL1 and IRQE. In addition,
SPORT1 may be reconfigured for IRQ0, IRQ1, FLAG_IN and
FLAG_OUT, for a total of six external interrupts. The ADSP-
2185L also supports internal interrupts from the timer, the byte
DMA port, the two serial ports, software and the power-down
control circuit. The interrupt levels are internally prioritized and
individually maskable (except power down and reset). The
IRQ2, IRQ0 and IRQ1 input pins can be programmed to be
either level- or edge-sensitive. IRQL0 and IRQL1 are level-
sensitive and IRQE is edge sensitive. The priorities and vector
addresses of all interrupts are shown in Table I.

Table I. Interrupt Priority and Interrupt Vector Addresses

Interrupt Vector

Source of Interrupt

Address (Hex)

RESET (or Power-Up with PUCR = 1) 0000 (Highest Priority)
Power-Down (Nonmaskable)

002C

IRQ2

0004

IRQL1

0008

IRQL0

000C

SPORT0 Transmit

0010

SPORT0 Receive

0014

IRQE

0018

BDMA Interrupt

001C

SPORT1 Transmit or IRQ1

0020

SPORT1 Receive or IRQ0

0024

Timer

0028 (Lowest Priority)

Interrupt routines can either be nested with higher priority inter-
rupts taking precedence or processed sequentially. Interrupts
can be masked or unmasked with the IMASK register. Indi-
vidual interrupt requests are logically ANDed with the bits in
IMASK; the highest priority unmasked interrupt is then se-
lected. The power-down interrupt is nonmaskable.

The ADSP-2185L masks all interrupts for one instruction cycle
following the execution of an instruction that modifies the
IMASK register. This does not affect serial port auto-
buffering or DMA transfers.

The interrupt control register, ICNTL, controls interrupt nest-
ing and defines the IRQ0, IRQ1 and IRQ2 external interrupts to
be either edge- or level-sensitive. The IRQE pin is an external
edge-sensitive interrupt and can be forced and cleared. The
IRQL0 and IRQL1 pins are external level-sensitive interrupts.

The IFC register is a write-only register used to force and clear
interrupts. On-chip stacks preserve the processor status and are
automatically maintained during interrupt handling. The stacks are
twelve levels deep to allow interrupt, loop and subroutine nest-
ing. The following instructions allow global enable or disable
servicing of the interrupts (including power down), regardless of
the state of IMASK. Disabling the interrupts does not affect se-
rial port autobuffering or DMA.

ENA INTS;
DIS INTS;

When the processor is reset, interrupt servicing is enabled.

REV. A

ADSP-2185L

LOW POWER OPERATION

The ADSP-2185L has three low power modes that significantly
reduce the power dissipation when the device operates under
standby conditions. These modes are:

· Power-Down
· Idle
· Slow Idle

The CLKOUT pin may also be disabled to reduce external
power dissipation.

Power-Down

The ADSP-2185L processor has a low power feature that lets
the processor enter a very low power dormant state through
hardware or software control. Here is a brief list of power-down
features. Refer to the ADSP-2100 Family User's Manual, Third
Edition, "System Interface" chapter, for detailed information
about the power-down feature.

· Quick recovery from power-down. The processor begins ex-

ecuting instructions in as few as 400 CLKIN cycles.

· Support for an externally generated TTL or CMOS processor

clock. The external clock can continue running during power-
down without affecting the 400 CLKIN cycle recovery.

· Support for crystal operation includes disabling the oscillator

to save power (the processor automatically waits 4096 CLKIN
cycles for the crystal oscillator to start and stabilize), and let-
ting the oscillator run to allow 400 CLKIN cycle start up.

· Power-down is initiated by either the power-down pin (PWD)

or the software power-down force bit Interrupt support allows
an unlimited number of instructions to be executed before op-
tionally powering down. The power-down interrupt also can
be used as a non-maskable, edge-sensitive interrupt.

· Context clear/save control allows the processor to continue

where it left off or start with a clean context when leaving the
power-down state.

· The RESET pin also can be used to terminate power-down.

· Power-down acknowledge pin indicates when the processor

has entered power-down.

Idle

When the ADSP-2185L is in the Idle Mode, the processor waits
indefinitely in a low power state until an interrupt occurs. When
an unmasked interrupt occurs, it is serviced; execution then con-
tinues with the instruction following the IDLE instruction. In
Idle Mode IDMA, BDMA and autobuffer cycle steals still occur.

Slow Idle

The IDLE instruction on the ADSP-2185L slows the processor's
internal clock signal, further reducing power consumption. The
reduced clock frequency, a programmable fraction of the nor-
mal clock rate, is specified by a selectable divisor given in the
IDLE instruction. The format of the instruction is

IDLE (n);

where n = 16, 32, 64 or 128. This instruction keeps the proces-
sor fully functional, but operating at the slower clock rate. While
it is in this state, the processor's other internal clock signals,
such as SCLK, CLKOUT and timer clock, are reduced by the
same ratio. The default form of the instruction, when no clock
divisor is given, is the standard IDLE instruction.

When the IDLE (n) instruction is used, it effectively slows down
the processor's internal clock and thus its response time to in-
coming interrupts. The one-cycle response time of the standard
idle state is increased by n, the clock divisor. When an enabled
interrupt is received, the ADSP-2185L will remain in the idle
state for up to a maximum of n processor cycles (n = 16, 32, 64
or 128) before resuming normal operation.

When the IDLE (n) instruction is used in systems that have an
externally generated serial clock (SCLK), the serial clock rate
may be faster than the processor's reduced internal clock rate.
Under these conditions, interrupts must not be generated at a
faster rate than can be serviced, due to the additional time the
processor takes to come out of the idle state (a maximum of n
processor cycles).

SYSTEM INTERFACE

Figure 2 shows a typical basic system configuration with the
ADSP-2185L, two serial devices, a byte-wide EPROM, and
optional external program and data overlay memories (mode se-
lectable). Programmable wait state generation allows the proces-
sor to connect easily to slow peripheral devices. The ADSP-2185L
also provides four external interrupts and two serial ports or six
external interrupts and one serial port. Host Memory Mode al-
lows access to the full external data bus, but limits addressing to
a single address bit (A0). Additional system peripherals can be
added in this mode through the use of external hardware to gen-
erate and latch address signals.

Clock Signals

The ADSP-2185L can be clocked by either a crystal or a TTL-
compatible clock signal.

The CLKIN input cannot be halted, changed during operation
or operated below the specified frequency during normal opera-
tion. The only exception is while the processor is in the power-
down state. For additional information, refer to Chapter 9,
ADSP-2100 Family User's Manual, Third Edition, for detailed in-
formation on this power-down feature.

If an external clock is used, it should be a TTL-compatible sig-
nal running at half the instruction rate. The signal is connected
to the processor's CLKIN input. When an external clock is
used, the XTAL input must be left unconnected.

The ADSP-2185L uses an input clock with a frequency equal to
half the instruction rate; a 26.00 MHz input clock yields a 19 ns
processor cycle (which is equivalent to 52 MHz). Normally, in-
structions are executed in a single processor cycle. All device
timing is relative to the internal instruction clock rate, which is
indicated by the CLKOUT signal when enabled.

Because the ADSP-2185L includes an on-chip oscillator circuit,
an external crystal may be used. The crystal should be connected
across the CLKIN and XTAL pins, with two capacitors connected
as shown in Figure 3. Capacitor values are dependent on crystal
type and should be specified by the crystal manufacturer. A
parallel-resonant, fundamental frequency, microprocessor-grade
crystal should be used.

A clock output (CLKOUT) signal is generated by the processor
at the processor's cycle rate. This can be enabled and disabled
by the CLK0DIS bit in the SPORT0 Autobuffer Control Register.

ADSP-2185L

REV. A

1/2x CLOCK

CRYSTAL

SERIAL
DEVICE

SCLK1
RFS1 OR

IRQ0

TFS1 OR

IRQ1

DT1 OR FL0
DR1 OR FL1

SPORT1

SCLK0
RFS0
TFS0
DT0
DR0

SPORT0

A0-A21

DATA

BYTE

MEMORY

I/O SPACE

(PERIPHERALS)

DATA

ADDR

DATA

ADDR

2048 LOCATIONS

OVERLAY

MEMORY

TWO 8K

PM SEGMENTS

TWO 8K

DM SEGMENTS

23-0

13-0

23-8

10-0

15-8

23-16

13-0

FL0-2
PF3

CLKIN

XTAL

ADDR13-0

DATA23-0

BMS

IOMS

PMS

DMS
CMS

BGH

PWD

PWDACK

ADSP-2185L

1/2x CLOCK

CRYSTAL

SERIAL
DEVICE

SYSTEM

INTERFACE

CONTROLLER

SPORT1

SCLK0
RFS0
TFS0
DT0
DR0

SPORT0

IAD15-0

IDMA PORT

FL0-2
PF3

CLKIN

XTAL

DATA23-8

BMS

IOMS

PMS

DMS
CMS

BGH

ADSP-2185L

IRQ2

/PF7

IRQE

/PF4

IRQL0

/PF5

IRQL1

/PF6

HOST MEMORY MODE

IRQ2

/PF7

IRQE

/PF4

IRQL0

/PF5

IRQL1

/PF6

PF2 [MODE C]
PF1 [MODE B]
PF0 [MODE A]

FULL MEMORY MODE

IRD

/D6

IWR

/D7

/D4

SCLK1

RFS1 OR

IRQ0

TFS1 OR

IRQ1

DT1 OR FO
DR1 OR FI

SERIAL
DEVICE

IAL/D5

IACK

/D3

PWD

PWDACK

PF2 [MODE C]
PF1 [MODE B]
PF0 [MODE A]

Figure 2. ADSP-2185L Basic System Configuration

CLKIN

CLKOUT

XTAL

DSP

Figure 3. External Crystal Connections

Reset

The RESET signal initiates a master reset of the ADSP-2185L.
The RESET signal must be asserted during the power-up se-
quence to assure proper initialization. RESET during initial
power-up must be held long enough to allow the internal clock
to stabilize. If RESET is activated any time after power-up, the
clock continues to run and does not require stabilization time.

The power-up sequence is defined as the total time required for
the crystal oscillator circuit to stabilize after a valid V

is ap-

plied to the processor, and for the internal phase-locked loop
(PLL) to lock onto the specific crystal frequency. A minimum
of 2000 CLKIN cycles ensures that the PLL has locked, but
does not include the crystal oscillator start-up time. During this
power-up sequence the RESET signal should be held low. On
any subsequent resets, the RESET signal must meet the mini-
mum pulsewidth specification, t

RSP

The RESET input contains some hysteresis; however, if an
RC circuit is used to generate the RESET signal, an external
Schmidt trigger is recommended.

The master reset sets all internal stack pointers to the empty
stack condition, masks all interrupts and clears the MSTAT
register. When RESET is released, if there is no pending bus
request and the chip is configured for booting, the boot-loading
sequence is performed. The first instruction is fetched from
on-chip program memory location 0x0000 once boot loading
completes.

MODES OF OPERATION

Table II summarizes the ADSP-2185L memory modes.

Setting Memory Mode

Memory Mode selection for the ADSP-2185L is made during
chip reset through the use of the Mode C pin. This pin is multi-
plexed with the DSP's PF2 pin, so care must be taken in how
the mode selection is made. The two methods for selecting the
value of Mode C are active and passive.

Passive configuration

involves the use a pull-up or pull-down

resistor connected to the Mode C pin. To minimize power con-
sumption, or if the PF2 pin is to be used as an output in the
DSP application, a weak pull-up or pull-down, on the order of
100 k

, can be used. This value should be sufficient to pull the

pin to the desired level and still allow the pin to operate as
a programmable flag output without undue strain on the
processor's output driver. For minimum power consumption
during power-down, reconfigure PF2 to be an input, as the
pull-up or pull-down will hold the pin in a known state, and will
not switch.

Active configuration

involves the use of a three-statable exter-

nal driver connected to the Mode C pin. A driver's output en-
able should be connected to the DSP's RESET signal such that
it only drives the PF2 pin when RESET is active (low). When
RESET is deasserted, the driver should three-state, thus allow-
ing full use of the PF2 pin as either an input or output. To
minimize power consumption during power-down, configure
the programmable flag as an output when connected to a three-
stated buffer. This ensures that the pin will be held at a con-
stant level and not oscillate should the three-state driver's level
hover around the logic switching point.

REV. A

ADSP-2185L

Table II. Modes of Operations

MODE C

MODE B

MODE A

Booting Method

BDMA feature is used to load the first 32 program memory words from the byte memory

space. Program execution is held off until all 32 words have been loaded. Chip is configured
in Full Memory Mode.

No Automatic boot operations occur. Program execution starts at external memory location

0. Chip is configured in Full Memory Mode. BDMA can still be used, but the processor does
not automatically use or wait for these operations.

BDMA feature is used to load the first 32 program memory words from the byte memory

space. Program execution is held off until all 32 words have been loaded. Chip is config-
ured in Host Mode. (REQUIRES ADDITIONAL HARDWARE.)

IDMA feature is used to load any internal memory as desired. Program execution is held off

until internal program memory location 0 is written to. Chip is configured in Host Mode.

NOTES

All mode pins are recognized while RESET is active (low).

When Mode C = 0, Full Memory enabled. When Mode C = 1, Host Memory Mode enabled.

When Mode B = 0, Auto Booting enabled. When Mode B = 1, no Auto Booting.

When Mode A = 0, BDMA enabled. When Mode A = 1, IDMA enabled.

Considered as standard operating settings. Using these configurations allows for easier design and better memory management.

MEMORY ARCHITECTURE

The ADSP-2185L provides a variety of memory and peripheral
interface options. The key functional groups are Program
Memory, Data Memory, Byte Memory, and I/O. Refer to the
following figures and tables for PM and DM memory alloca-
tions in the ADSP-2185L.

PROGRAM MEMORY

Program Memory (Full Memory Mode)

is a 24-bit-wide

space for storing both instruction opcodes and data. The
ADSP-2185L has 16K words of Program Memory RAM on
chip, and the capability of accessing up to two 8K external
memory overlay spaces using the external data bus.

Program Memory (Host Mode)

allows access to all internal

memory. External overlay access is limited by a single external
address line (A0). External program execution is not available in
host mode due to a restricted data bus that is 16-bits wide only.

Table III. PMOVLAY Bits

PMOVLAY Memory

A13

A12:0

Internal

Not Applicable

External

13 LSBs of Address

Overlay 1

Between 0x2000
and 0x3FFF

External

13 LSBs of Address

Overlay 2

Between 0x2000
and 0x3FFF

ACCESSIBLE WHEN
PMOVLAY = 2

ACCESSIBLE WHEN
PMOVLAY = 1

ALWAYS

ACCESSIBLE
AT ADDRESS

0x0000 0x1FFF

ACCESSIBLE WHEN

PMOVLAY = 0

PM (MODE B = 0)

INTERNAL
MEMORY

EXTERNAL
MEMORY

0x2000
0x3FFF

8K INTERNAL
PMOVLAY = 0

8K EXTERNAL

PROGRAM MEMORY

MODE B = 1

ADDRESS

0x3FFF

0x2000

0x1FFF

0x0000

8K INTERNAL
PMOVLAY = 0

8K EXTERNAL

PMOVLAY = 1 OR 2

0x3FFF

0x2000

0x1FFF

8K INTERNAL

0x0000

PROGRAM MEMORY

MODE B = 0

ADDRESS

ACCESSIBLE WHEN
PMOVLAY = 0

INTERNAL
MEMORY

EXTERNAL
MEMORY

0x2000
0x3FFF

0x0000
0x1FFF

PM (MODE B = 1)

RESERVED

WHEN MODE B = 1, PMOVLAY MUST BE SET TO 0

SEE TABLE III FOR PMOVLAY BITS

ACCESSIBLE WHEN

PMOVLAY = 0

RESERVED

Figure 4. Program Memory

ADSP-2185L

REV. A

DATA MEMORY

Data Memory (Full Memory Mode)

is a 16-bit-wide space

used for the storage of data variables and for memory-mapped
control registers. The ADSP-2185L has 16K words on Data
Memory RAM on chip, consisting of 16,352 user-accessible lo-
cations and 32 memory-mapped registers. Support also exists
for up to two 8K external memory overlay spaces through the
external data bus. All internal accesses complete in one cycle.
Accesses to external memory are timed using the wait states
specified by the DWAIT register.

ACCESSIBLE WHEN
DMOVLAY = 2

ACCESSIBLE WHEN
DMOVLAY = 1

32 MEMORY

MAPPED

REGISTERS

3FFF

2000

1FFF

INTERNAL

8160

WORDS

0000

DATA MEMORY

ADDRESS

ALWAYS

ACCESSIBLE
AT ADDRESS

2000 0

3FFF

ACCESSIBLE WHEN

DMOVLAY = 0

INTERNAL
MEMORY

EXTERNAL
MEMORY

0000

1FFF

0000

1FFF

0000

1FFF

DATA MEMORY

8K INTERNAL
DMOVLAY = 0

EXTERNAL 8K

DMOVLAY = 1, 2

3FE0

3FDF

Figure 5. Data Memory Map

Data Memory (Host Mode) allows access to all internal memory.
External overlay access is limited by a single external address
line (A0). The DMOVLAY bits are defined in Table IV.

Table IV. DMOVLAY Bits

DMOVLAY

Memory

A13

A12:0

Internal

Not Applicable

External

13 LSBs of Address

Overlay 1

Between 0x2000
and 0x3FFF

External

13 LSBs of Address

Overlay 2

Between 0x2000
and 0x3FFF

I/O Space (Full Memory Mode)

The ADSP-2185L supports an additional external memory
space called I/O space. This space is designed to support simple
connections to peripherals (such as data converters and external
registers) or to bus interface ASIC data registers. I/O space sup-
ports 2048 locations of 16-bit wide data. The lower eleven bits
of the external address bus are used; the upper three bits are un-
defined. Two instructions were added to the core ADSP-2100
Family instruction set to read from and write to I/O memory
space. The I/O space also has four dedicated 3-bit wait state
registers, IOWAIT0-3, that specify up to seven wait states to be
automatically generated for each of four regions. The wait states
act on address ranges as shown in Table V.

Table V. Wait States

Address Range

Wait State Register

0x0000x1FF

IOWAIT0

0x2000x3FF

IOWAIT1

0x4000x5FF

IOWAIT2

0x6000x7FF

IOWAIT3

Composite Memory Select (CMS)

The ADSP-2185L has a programmable memory select signal
that is useful for generating memory select signals for memories
mapped to more than one space. The CMS signal is generated
to have the same timing as each of the individual memory select
signals (PMS, DMS, BMS, IOMS) but can combine their
functionality.

Each bit in the CMSSEL register, when set, causes the CMS
signal to be asserted when the selected memory select is as-
serted. For example, to use a 32K word memory to act as both
program and data memory, set the PMS and DMS bits in the
CMSSEL register and use the CMS pin to drive the chip select
of the memory; use either DMS or PMS as the additional
address bit.

The CMS pin functions like the other memory select signals,
with the same timing and bus request logic. A 1 in the enable bit
causes the assertion of the CMS signal at the same time as the
selected memory select signal. All enable bits default to 1 at re-
set, except the BMS bit.

Boot Memory Select (BMS) Disable

The ADSP-2185L also lets you boot the processor from one ex-
ternal memory space while using a different external memory
space for BDMA transfers during normal operation. You can
use the CMS to select the first external memory space for
BDMA transfers and BMS to select the second external memory
space for booting. The BMS signal can be disabled by setting
Bit 3 of the System Control Register to 1. The System Control
Register is illustrated in Figure 6.

15 14

13 12 11

DM (0 3FFF)

SYSTEM CONTROL REGISTER

SPORT0 ENABLE

1 = ENABLED, 0 = DISABLED

SPORT1 ENABLE

1 = ENABLED, 0 = DISABLED

SPORT1 CONFIGURE

1 = SERIAL PORT

0 = FI, FO,

IRQ0

IRQ1

, SCLK

PWAIT
PROGRAM MEMORY
WAIT STATES

BMS

ENABLE

0 = ENABLED, 1 = DISABLED

Figure 6. System Control Register

Byte Memory

The byte memory space is a bidirectional, 8-bit-wide, external
memory space used to store programs and data. Byte memory is
accessed using the BDMA feature. The BDMA Control Register is
shown in Figure 7. The byte memory space consists of 256 pages,
each of which is 16K

BDMA CONTROL

BMPAGE

BTYPE

BDIR
0 = LOAD FROM BM
1 = STORE TO BM

BCR
0 = RUN DURING BDMA
1 = HALT DURING BDMA

15 14 13 12 11 10

DM (0 3FE3)

Figure 7. BDMA Control Register

The byte memory space on the ADSP-2185L supports read and
write operations as well as four different data formats. The byte
memory uses data bits 15:8 for data. The byte memory uses
data bits 23:16 and address bits 13:0 to create a 22-bit address.
This allows up to a 4 meg

8 (32 megabit) ROM or RAM to be

used without glue logic. All byte memory accesses are timed by
the BMWAIT register.

REV. A

ADSP-2185L

Internal Memory DMA Port (IDMA Port; Host Memory
Mode)

The IDMA Port provides an efficient means of communication
between a host system and the ADSP-2185L. The port is used
to access the on-chip program memory and data memory of the
DSP with only one DSP cycle per word overhead. The IDMA
port cannot be used, however, to write to the DSP's memory-
mapped control registers. A typical IDMA transfer process is
described as follows:

1. Host starts IDMA transfer.

2. Host checks IACK control line to see if the DSP is busy.

3. Host uses IS and IAL control lines to latch the DMA starting

address (IDMAA) into the DSP's IDMA control registers.
IAD[15] must be set = 0.

4. Host uses IS and IRD (or IWR) to read (or write) DSP inter-

nal memory (PM or DM).

5. Host checks IACK line to see if the DSP has completed the

previous IDMA operation.

6. Host ends IDMA transfer.

The IDMA port has a 16-bit multiplexed address and data bus
and supports 24-bit program memory. The IDMA port is
completely asynchronous and can be written to while the
ADSP-2185L is operating at full speed.

The DSP memory address is latched and then automatically in-
cremented after each IDMA transaction. An external device can
therefore access a block of sequentially addressed memory by
specifying only the starting address of the block. This increases
throughput as the address does not have to be sent for each
memory access.

IDMA Port access occurs in two phases. The first is the IDMA
Address Latch cycle. When the acknowledge is asserted, a
14-bit address and 1-bit destination type can be driven onto the
bus by an external device. The address specifies an on-chip
memory location; the destination type specifies whether it is a
DM or PM access. The falling edge of the address latch signal
latches this value into the IDMAA register.

Once the address is stored, data can either be read from or
written to the ADSP-2185L's on-chip memory. Asserting the
select line (IS) and the appropriate read or write line (IRD and
IWR respectively) signals the ADSP-2185L that a particular
transaction is required. In either case, there is a one-processor-
cycle delay for synchronization. The memory access consumes
one additional processor cycle.

Once an access has occurred, the latched address is automati-
cally incremented and another access can occur.

Through the IDMAA register, the DSP can also specify the
starting address and data format for DMA operation. Asserting
the IDMA port select (IS) and address latch enable (IAL) di-
rects the ADSP-2185L to write the address onto the IAD014
bus into the IDMA Control Register. The IDMAA register,
shown below, is memory mapped at address DM (0x3FE0).
Note that the latched address (IDMAA) cannot be read back by
the host. See Figure 8 for more information on IDMA and
DMA memory maps.

Byte Memory DMA (BDMA, Full Memory Mode)

The Byte memory DMA controller allows loading and storing of
program instructions and data using the byte memory space.
The BDMA circuit is able to access the byte memory space
while the processor is operating normally, and steals only one
DSP cycle per 8-, 16- or 24-bit word transferred.

The BDMA circuit supports four different data formats that are
selected by the BTYPE register field. The appropriate number
of 8-bit accesses are done from the byte memory space to build
the word size selected. Table VI shows the data formats sup-
ported by the BDMA circuit.

Table VI. Data Formats

Internal

BTYPE

Memory Space

Word Size

Alignment

Program Memory

Full Word

Data Memory

Full Word

Data Memory

MSBs

Data Memory

LSBs

Unused bits in the 8-bit data memory formats are filled with 0s.
The BIAD register field is used to specify the starting address
for the on-chip memory involved with the transfer. The 14-bit
BEAD register specifies the starting address for the external
byte memory space. The 8-bit BMPAGE register specifies the
starting page for the external byte memory space. The BDIR
register field selects the direction of the transfer. Finally the 14-
bit BWCOUNT register specifies the number of DSP words to
transfer and initiates the BDMA circuit transfers.

BDMA accesses can cross page boundaries during sequential
addressing. A BDMA interrupt is generated on the completion
of the number of transfers specified by the BWCOUNT
register.

The BWCOUNT register is updated after each transfer so it can
be used to check the status of the transfers. When it reaches
zero, the transfers have finished and a BDMA interrupt is gener-
ated. The BMPAGE and BEAD registers must not be accessed
by the DSP during BDMA operations.

The source or destination of a BDMA transfer will always be
on-chip program or data memory.

When the BWCOUNT register is written with a nonzero value,
the BDMA circuit starts executing byte memory accesses with
wait states set by BMWAIT. These accesses continue until the
count reaches zero. When enough accesses have occurred to
create a destination word, it is transferred to or from on-chip
memory. The transfer takes one DSP cycle. DSP accesses to ex-
ternal memory have priority over BDMA byte memory accesses.

The BDMA Context Reset bit (BCR) controls whether or not
the processor is held off while the BDMA accesses are occur-
ring. Setting the BCR bit to 0 allows the processor to continue
operations. Setting the BCR bit to 1 causes the processor to
stop execution while the BDMA accesses are occurring, to clear
the context of the processor and start execution at address 0
when the BDMA accesses have completed.

ADSP-2185L

REV. A

IDMA CONTROL (U = UNDEFINED AT RESET)

DM(0 3FE0)

IDMAA
ADDRESS

IDMAD
DESTINATION MEMORY TYPE:
0 = PM
1 = DM

15 14 13 12 11 10

Figure 8. IDMA Control/OVLAY Registers

Bootstrap Loading (Booting)

The ADSP-2185L has two mechanisms to allow automatic
loading of the internal program memory after reset. The method
for booting after reset is controlled by the Mode A, B and C
configuration bits.

When the mode pins specify BDMA booting, the ADSP-2185L
initiates a BDMA boot sequence when reset is released.

The BDMA interface is set up during reset to the following de-
faults when BDMA booting is specified: the BDIR, BMPAGE,
BIAD and BEAD registers are set to 0, the BTYPE register is
set to 0 to specify program memory 24-bit words, and the
BWCOUNT register is set to 32. This causes 32 words of on-
chip program memory to be loaded from byte memory. These
32 words are used to set up the BDMA to load in the remaining
program code. The BCR bit is also set to 1, which causes pro-
gram execution to be held off until all 32 words are loaded into
on-chip program memory. Execution then begins at address 0.

The ADSP-2100 Family Development Software (Revision 5.02
and later) fully supports the BDMA booting feature and can
generate byte memory space compatible boot code.

The IDLE instruction can also be used to allow the processor to
hold off execution while booting continues through the BDMA
interface. For BDMA accesses while in Host Mode, the ad-
dresses to boot memory must be constructed externally to the
ADSP-2185L. The only memory address bit provided by the
processor is A0.

IDMA Port Booting

The ADSP-2185L can also boot programs through its Internal
DMA port. If Mode C = 1, Mode B = 0 and Mode A = 1, the
ADSP-2185L boots from the IDMA port. IDMA feature can
load as much on-chip memory as desired. Program execution is
held off until on-chip program memory location 0 is written to.

Bus Request and Bus Grant (Full Memory Mode)

The ADSP-2185L can relinquish control of the data and ad-
dress buses to an external device. When the external device re-
quires access to memory, it asserts the bus request (BR) signal.
If the ADSP-2185L is not performing an external memory ac-
cess, it responds to the active BR input in the following proces-
sor cycle by:

· three-stating the data and address buses and the PMS, DMS,

BMS, CMS, IOMS, RD, WR output drivers,

· asserting the bus grant (BG) signal, and

· halting program execution.

If Go Mode is enabled, the ADSP-2185L will not halt program
execution until it encounters an instruction that requires an ex-
ternal memory access.

If the ADSP-2185L is performing an external memory access
when the external device asserts the BR signal, it will not three-
state the memory interfaces or assert the BG signal until the
processor cycle after the access completes. The instruction does
not need to be completed when the bus is granted. If a single in-
struction requires two external memory accesses, the bus will be
granted between the two accesses.

When the BR signal is released, the processor releases the BG
signal, reenables the output drivers and continues program ex-
ecution from the point at which it stopped.

The bus request feature operates at all times, including when
the processor is booting and when RESET is active.

The BGH pin is asserted when the ADSP-2185L is ready to ex-
ecute an instruction, but is stopped because the external bus is
already granted to another device. The other device can release
the bus by deasserting bus request. Once the bus is released, the
ADSP-2185L deasserts BG and BGH and

executes the external

memory access.

Flag I/O Pins

The ADSP-2185L has eight general purpose programmable
input/output flag pins. They are controlled by two memory
mapped registers. The PFTYPE register determines the direc-
tion, 1 = output and 0 = input. The PFDATA register is used to
read and write the values on the pins. Data being read from a
pin configured as an input is synchronized to the ADSP-2185L's
clock. Bits that are programmed as outputs will read the value
being output. The PF pins default to input during reset.

In addition to the programmable flags, the ADSP-2185L has
five fixed-mode flags, FLAG_IN, FLAG_OUT, FL0, FL1 and
FL2. FL0-FL2 are dedicated output flags. FLAG_IN and
FLAG_OUT are available as an alternate configuration of
SPORT1.

Note: Pins PF0, PF1, PF2 and PF3 are also used for device
configuration during reset.

INSTRUCTION SET DESCRIPTION

The ADSP-2185L assembly language instruction set has an
algebraic syntax that was designed for ease of coding and read-
ability. The assembly language, which takes full advantage of
the processor's unique architecture, offers the following benefits:

· The algebraic syntax eliminates the need to remember cryptic

assembler mnemonics. For example, a typical arithmetic add
instruction, such as AR = AX0 + AY0, resembles a simple
equation.

· Every instruction assembles into a single, 24-bit word that can

execute in a single instruction cycle.

· The syntax is a superset ADSP-2100 Family assembly lan-

guage and is completely source and object code compatible
with other family members. Programs may need to be relo-
cated to utilize on-chip memory and conform to the ADSP-
2185L's interrupt vector and reset vector map.

· Sixteen condition codes are available. For conditional jump,

call, return or arithmetic instructions, the condition can be
checked and the operation executed in the same instruction
cycle.

· Multifunction instructions allow parallel execution of an

arithmetic instruction with up to two fetches or one write to
processor memory space during a single instruction cycle.

REV. A

ADSP-2185L

DESIGNING AN EZ-ICE-COMPATIBLE SYSTEM

The ADSP-2185L has on-chip emulation support and an ICE-
Port, a special set of pins that interface to the EZ-ICE. These
features allow in-circuit emulation without replacing the target
system processor by using only a 14-pin connection from the
target system to the EZ-ICE. Target systems must have a 14-pin
connector to accept the EZ-ICE's in-circuit probe, a 14-pin plug.
See the ADSP-2100 Family EZ-Tools data sheet for complete in-
formation on ICE products.

Issuing the chip reset command during emulation causes the
DSP to perform a full chip reset, including a reset of its memory
mode. Therefore, it is vital that the mode pins are set correctly
PRIOR to issuing a chip reset command from the emulator user
interface. If you are using a passive method of maintaining
mode information (as discussed in Setting Memory Modes)
then it does not matter that the mode information is latched by
an emulator reset. However, if you are using the RESET pin as
a method of setting the value of the mode pins, then you have to
take into consideration the effects of an emulator reset.

One method of ensuring that the values located on the mode
pins are those desired is to construct a circuit like the one shown
in Figure 9. This circuit forces the value located on the Mode A
pin to logic high; regardless if it latched via the RESET or
ERESET pin.

ERESET

RESET

ADSP-2185L

MODE A/PFO

PROGRAMMABLE I/O

Figure 9. Mode A Pin/EZ-ICE Circuit

The ICE-Port interface consists of the following ADSP-2185L
pins:

EBR

EBG

ERESET

EMS

EINT

ECLK

ELIN

ELOUT

These ADSP-2185L pins must be connected only to the EZ-ICE
connector in the target system. These pins have no function ex-
cept during emulation, and do not require pull-up or pull-down
resistors. The traces for these signals between the ADSP-2185L
and the connector must be kept as short as possible, no longer
than three inches.

The following pins are also used by the EZ-ICE:

RESET

GND

The EZ-ICE uses the EE (emulator enable) signal to take con-
trol of the ADSP-2185L in the target system. This causes the
processor to use its ERESET, EBR and EBG pins instead of the
RESET, BR and BG pins. The BG output is three-stated. These
signals do not need to be jumper-isolated in your system.

The EZ-ICE

connects to your target system via a ribbon cable

and a 14-pin female plug. The ribbon cable is 10 inches in
length with one end fixed to the EZ-ICE. The female plug is
plugged onto the 14-pin connector (a pin strip header) on the
target board.

Target Board Connector for EZ-ICE Probe

The EZ-ICE connector (a standard pin strip header) is shown in
Figure 10. You must add this connector to your target board
design if you intend to use the EZ-ICE. Be sure to allow enough
room in your system to fit the EZ-ICE probe onto the 14-pin
connector.

GND

KEY (NO PIN)

RESET

TOP VIEW

EBG

EBR

ELOUT

EINT

ELIN

ECLK

EMS

ERESET

Figure 10. Target Board Connector for EZ-ICE

The 14-pin, 2-row pin strip header is keyed at the Pin 7 loca-
tion--you must remove Pin 7 from the header. The pins must
be 0.025 inch square and at least 0.20 inch in length. Pin spac-
ing should be 0.1

0.1 inches. The pin strip header must have

at least 0.15 inch clearance on all sides to accept the EZ-ICE
probe plug.

Pin strip headers are available from vendors such as 3M,
McKenzie and Samtec.

Target Memory Interface

For your target system to be compatible with the EZ-ICE

emu-

lator, it must comply with the memory interface guidelines listed
below.

PM, DM, BM, IOM and CM

Design your Program Memory (PM), Data Memory (DM),
Byte Memory (BM), I/O Memory (IOM) and Composite
Memory (CM) external interfaces to comply with worst case
device timing requirements and switching characteristics as
specified in the DSP's data sheet. The performance of the
EZ-ICE

may approach published worst case specification for

some memory access timing requirements and switching
characteristics.

Note: If your target does not meet the worst case chip specifica-
tion for memory access parameters, you may not be able to
emulate your circuitry at the desired CLKIN frequency. De-
pending on the severity of the specification violation, you may
have trouble manufacturing your system as DSP components
statistically vary in switching characteristic and timing require-
ments within published limits.

ADSP-2185L

REV. A

Restriction:

All memory strobe signals on the ADSP-2185L

(RD, WR, PMS, DMS, BMS, CMS and IOMS) used in your
target system must have 10 k

pull-up resistors connected when

the EZ-ICE is being used. The pull-up resistors are necessary
because there are no internal pull-ups to guarantee their state
during prolonged three-state conditions resulting from typical
EZ-ICE debugging sessions. These resistors may be removed at
your option when the EZ-ICE is not being used.

Target System Interface Signals

When the EZ-ICE

board is installed, the performance on some

system signals changes. Design your system to be compatible
with the following system interface signal changes introduced by
the EZ-ICE

board:

· EZ-ICE

emulation introduces an 8 ns propagation delay be-

tween your target circuitry and the DSP on the RESET
signal.

· EZ-ICE

emulation introduces an 8 ns propagation delay be-

tween your target circuitry and the DSP on the BR signal.

· EZ-ICE

emulation ignores RESET and BR when single-

stepping.

· EZ-ICE

emulation ignores RESET and BR when in Emulator

Space (DSP halted).

· EZ-ICE

emulation ignores the state of target BR in certain

modes. As a result, the target system may take control of the
DSP's external memory bus only if bus grant (BG) is asserted
by the EZ-ICE

board's DSP.

ADSP-2185LSPECIFICATIONS

RECOMMENDED OPERATING CONDITIONS

K Grade

B Grade

Parameter

Min

Max

Min

Max

Unit

Supply Voltage

3.0

3.6

3.0

3.6

AMB

Ambient Operating Temperature

+70

+85

ELECTRICAL CHARACTERISTICS

K/B Grades

Parameter

Test Conditions

Min

Typ

Max

Unit

Hi-Level Input Voltage

1, 2

@ V

= max

2.0

Hi-Level CLKIN Voltage

@ V

= max

2.2

Lo-Level Input Voltage

1, 3

@ V

= min

0.8

Hi-Level Output Voltage

1, 4, 5

@ V

= min

= 0.5 mA

2.4

@ V

= min

= 100

0.3

Lo-Level Output Voltage

1, 4, 5

@ V

= min

= 2 mA

0.4

Hi-Level Input Current

@ V

= max

= V

max

Lo-Level Input Current

@ V

= max

= 0 V

OZH

Three-State Leakage Current

@ V

= max

= V

max

OZL

Three-State Leakage Current

@ V

= max

= 0 V

Supply Current (Idle)

@ V

= 3.3

= 19 ns

8.6

= 25 ns

= 30 ns

Supply Current (Dynamic)

@ V

= 3.3

AMB

= +25

= 19 ns

= 25 ns

= 30 ns

31.5

Input Pin Capacitance

3, 6, 12

@ V

= 2.5 V

= 1.0 MHz

AMB

= +25

Output Pin Capacitance

6, 7, 12, 13

@ V

= 2.5 V

= 1.0 MHz

AMB

= +25

NOTES

Bidirectional pins: D0D23, RFS0, RFS1, SCLK0, SCLK1, TFS0, TFS1, A1A13, PF0PF7.

Input only pins: RESET, BR, DR0, DR1, PWD.

Input only pins: CLKIN, RESET, BR, DR0, DR1, PWD.

Output pins: BG, PMS, DMS, BMS, IOMS, CMS, RD, WR, PWDACK, A0, DT0, DT1, CLKOUT, FL20, BGH.

Although specified for TTL outputs, all ADSP-2185L outputs are CMOS-compatible and will drive to V

and GND, assuming no dc loads.

Guaranteed but not tested.

Three-statable pins: A0A13, D0D23, PMS, DMS, BMS, IOMS, CMS, RD, WR, DT0, DT1, SCLK0, SCLK1, TFS0, TFS1, RFS0, RFS1, PF0PF7.

0 V on BR.

Idle refers to ADSP-2185L state of operation during execution of IDLE instruction. Deasserted pins are driven to either

or GND.

= 0 V and 3 V. For typical figures for supply currents, refer to Power Dissipation section.

measurement taken with all instructions executing from internal memory. 50% of the instructions are multifunction (types 1, 4, 5, 12, 13, 14), 30% are type 2

and type 6, and 20% are idle instructions.

Applies to LQFP package type.

Output pin capacitance is the capacitive load for any three-stated output pin.

Specifications subject to change without notice.

REV. A

ADSP-2185L

REV. A

ESD SENSITIVITY

The ADSP-2185L is an ESD (electrostatic discharge) sensitive device. Electrostatic charges readily
accumulate on the human body and equipment and can discharge without detection. Permanent
damage may occur to devices subjected to high energy electrostatic discharges.

The ADSP-2185L features proprietary ESD protection circuitry to dissipate high energy discharges
(Human Body Model). Per method 3015 of MIL-STD-883, the ADSP-2185L has been classified
as a Class 1 device.

Proper ESD precautions are recommended to avoid performance degradation or loss of function-
ality. Unused devices must be stored in conductive foam or shunts, and the foam should be
discharged to the destination before devices are removed.

TIMING PARAMETERS

GENERAL NOTES

Use the exact timing information given. Do not attempt to de-
rive parameters from the addition or subtraction of others.
While addition or subtraction would yield meaningful results for
an individual device, the values given in this data sheet reflect
statistical variations and worst cases. Consequently, you cannot
meaningfully add up parameters to derive longer times.

TIMING NOTES

Switching Characteristics specify how the processor changes its
signals. You have no control over this timing--circuitry external
to the processor must be designed for compatibility with these
signal characteristics. Switching characteristics tell you what the
processor will do in a given circumstance. You can also use switch-
ing characteristics to ensure that any timing requirement of a
device connected to the processor (such as memory) is satisfied.

Timing Requirements apply to signals that are controlled by cir-
cuitry external to the processor, such as the data input for a read
operation. Timing requirements guarantee that the processor
operates correctly with other devices.

MEMORY TIMING SPECIFICATIONS

The table below shows common memory device specifications
and the corresponding ADSP-2185L timing parameters, for
your convenience.

Memory

ADSP-2185L

Timing

Device

Timing

Parameter

Specification

Parameter

Definition

Address Setup to

ASW

A0A13, xMS Setup before

Write Start

WR Low

Address Setup to

A0A13, xMS Setup before

Write End

WR Deasserted

Address Hold Time

WRA

A0A13, xMS Hold before
WR Low

Data Setup Time

Data Setup before WR High

Data Hold Time

Data Hold after WR High

OE to Data Valid

RDD

RD Low to Data Valid

Address Access Time

A0A13, xMS to Data Vali

xMS = PMS, DMS, BMS, CMS, IOMS.

FREQUENCY DEPENDENCY FOR TIMING
SPECIFICATIONS

= Instruction Clock Period.

CKI

= External Clock Period.

is defined as 0.5t

CKI

. The ADSP-2185L uses an input clock

with a frequency equal to half the instruction rate: a 26 MHz
input clock (which is equivalent to 38 ns) yields a 19 ns processor
cycle (equivalent to 52 MHz). t

values within the range of

0.5t

CKI

period should be substituted for all relevant timing

parameters to obtain the specification value.

Example: t

CKH

= 0.5t

7 ns = 0.5 (19 ns) 7 ns = 2.5 ns

ABSOLUTE MAXIMUM RATINGS

Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . 0.3 V to +4.6 V
Input Voltage . . . . . . . . . . . . . . . . . . . . . 0.5 V to V

+ 0.5 V

Output Voltage Swing . . . . . . . . . . . . . . 0.5 V to V

+ 0.5 V

Operating Temperature Range (Ambient) . . . . 40

C to +85

Storage Temperature Range . . . . . . . . . . . . . 65

C to +150

Lead Temperature (5 sec) LQFP . . . . . . . . . . . . . . . . . +280

*Stresses above those listed under Absolute Maximum Ratings may cause perma-

nent damage to the device. These are stress ratings only; functional operation of
the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.

WARNING!

ESD SENSITIVE DEVICE

REV. A

ADSP-2185L

Total Power Dissipation = P

INT

+ (C

f )

INT

= internal power dissipation from Power vs. Frequency

graph, see Figure 13.

f ) is calculated for each output:

# of
Pins

Address, DMS

10 pF

3.3

33.3 MHz

29.0 mW

Data Output, WR 9

10 pF

3.3

16.67 MHz =

16.3 mW

10 pF

3.3

16.67 MHz =

1.8 mW

CLKOUT

10 pF

3.3

33.3 MHz

3.6 mW

50.7 mW

Total power dissipation for this example is P

INT

+ 50.7 mW.

FREQUENCY MHz

250

150

33.3

200

2185L POWER, INTERNAL

1, 3, 4

= 3.6V

= 3.3V

= 3.0V

197mW

161mW

130mW

128mW

104mW

84mW

POWER mW

100

FREQUENCY MHz

33.33

POWER, IDLE

1, 2, 3

= 3.6V

= 3.3V

= 3.0V

35mW

22mW

28mW

25mW

20mW

16mW

POWER mW

FREQUENCY MHz

33.33

POWER, IDLE

n MODES

IDLE (16)
IDLE (128)

28mW

13mW

12mW

20mW

10mW

9mW

POWER mW

VALID FOR ALL TEMPERATURE GRADES.

POWER REFLECTS DEVICE OPERATING WITH NO OUTPUT LOADS.

IDLE REFERS TO ADSP-2187L STATE OF OPERATION DURING EXECUTION OF IDLE

INSTRUCTION. DEASSERTED PINS ARE DRIVEN TO EITHER V

OR GND.

TYPICAL POWER DISSIPATION AT 3.3V V

AND 25 C EXCEPT WHERE SPECIFIED.

MEASUREMENT TAKEN WITH ALL INSTRUCTIONS EXECUTING FROM INTERNAL

MEMORY. 50% OF THE INSTRUCTIONS ARE MULTIFUNCTION (TYPES 1, 4, 5, 12, 13, 14),
30% ARE TYPE 2 AND TYPE 6, AND 20% ARE IDLE INSTRUCTIONS.

Figure 13. Power vs. Frequency

OUTPUT DRIVE CURRENTS

Figure 11 shows typical I-V characteristics for the output drivers
of the ADSP-2185L. The curves represent the current drive
capability of the output drivers as a function of output voltage.

SOURCE VOLTAGE Volts

60

SOURCE CURRENT mA

0.5

1.5

2.5

3.5

20

40

80

3.0V, +85 C

3.3V, +25 C

3.6V, 40 C

3.0V, +85 C

3.3V, +25 C

3.6V, 40 C

Figure 11. Typical Drive Currents

Figure 12 shows the typical power-down supply current.

NOTES:
1. REFLECTS ADSP-2187L OPERATION IN LOWEST POWER MODE.
(SEE "SYSTEM INTERFACE" CHAPTER OF THE

ADSP-2100 FAMILY

USER'S MANUAL FOR DETAILS.)
2. CURRENT REFLECTS DEVICE OPERATING WITH NO INPUT LOADS.

TEMPERATURE C

CURRENT (LOG SCALE) 

1000

100

= 3.6V

= 3.3V

Figure 12. Power-Down Supply Current (Typical)

POWER DISSIPATION

To determine total power dissipation in a specific application,
the following equation should be applied for each output:

C = load capacitance, f = output switching frequency.

Example:

In an application where external data memory is used and no other
outputs are active, power dissipation is calculated as follows:

Assumptions:

External data memory is accessed every cycle with 50% of the
address pins switching.

External data memory writes occur every other cycle with
50% of the data pins switching.

Each address and data pin has a 10 pF total load at the pin.

The application operates at V

= 3.3 V and t

= 34.7 ns.

ADSP-2185L

REV. A

CAPACITIVE LOADING

Figures 14 and 15 show the capacitive loading characteristics of
the ADSP-2185L.

 pF

RISE TIME (0.4V 2.4V) ns

200

100

150

T = +85 C
V

= 3.0V

250

Figure 14. Typical Output Rise Time vs. Load Capacitance,
C

(at Maximum Ambient Operating Temperature)

 pF

200

120

160

NOMINAL

VALID OUTPUT DELAY

OR HOLD ns

100

140

180

Figure 15. Typical Output Valid Delay or Hold vs. Load
Capacitance, C

(at Maximum Ambient Operating

Temperature)

TEST CONDITIONS
Output Disable Time

Output pins are considered to be disabled when they have
stopped driving and started a transition from the measured out-
put high or low voltage to a high impedance state, see Figure
16. The output disable time (t

DIS

) is the difference between

MEASURED

and t

DECAY

, see Figure 17. The time is the interval

from when a reference signal reaches a high or low voltage level
to when the output voltages have changed by 0.5 V from the
measured output high or low voltage. The decay time, t

DECAY

, is

dependent on the capacitive load, C

, and the current load, i

on the output pin. It can be approximated by the following
equation:

DECAY

· 0.5V

from which

DIS

MEASURED

DECAY

is calculated. If multiple pins (such as the data bus) are disabled,
the measurement value is that of the last pin to stop driving.

1.5V

INPUT

OUTPUT

1.5V

Figure 16. Voltage Reference Levels for AC Measure-
ments (Except Output Enable/Disable)

Output Enable Time

Output pins are considered to be enabled when they have made
a transition from a high-impedance state to when they start
driving. The output enable time (t

ENA

) is the interval from when

a reference signal reaches a high or low voltage level to when
the output has reached a specified high or low trip point, see
Figure 17. If multiple pins (such as the data bus) are enabled,
the measurement value is that of the first pin to start driving.

2.0V

1.0V

ENA

REFERENCE

SIGNAL

OUTPUT

DECAY

(MEASURED)

OUTPUT STOPS

DRIVING

OUTPUT STARTS

DRIVING

DIS

MEASURED

(MEASURED)

(MEASURED) 0.5V

(MEASURED) +0.5V

HIGH-IMPEDANCE STATE. TEST CONDITIONS CAUSE

THIS VOLTAGE LEVEL TO BE APPROXIMATELY 1.5V.

(MEASURED)

Figure 17. Output Enable/Disable

OUTPUT

PIN

50pF

+1.5V

Figure 18. Equivalent Device Loading for AC Measure-
ments (Including All Fixtures)

ENVIRONMENTAL CONDITIONS

Ambient Temperature Rating is shown below:

AMB

= T

CASE

(PD

)

CASE

= Case Temperature in

PD = Power Dissipation in W

= Thermal Resistance (Case-to-Ambient)

= Thermal Resistance (Junction-to-Ambient)

= Thermal Resistance (Junction-to-Case)

Package

LQFP

C/W

ADSP-2185L

REV. A

Parameter

Min

Max

Unit

Serial Ports

Timing Requirements:
t

SCK

SCLK Period

SCS

DR/TFS/RFS Setup before SCLK Low

SCH

DR/TFS/RFS Hold after SCLK Low

SCP

SCLK

Width

Switching Characteristics:
t

CLKOUT High to SCLK

OUT

0.25t

+ 10

SCDE

SCLK High to DT Enable

SCDV

SCLK High to DT Valid

TFS/RFS

OUT

Hold after SCLK High

TFS/RFS

OUT

Delay from SCLK High

SCDH

DT Hold after SCLK High

TDE

TFS (Alt) to DT Enable

TDV

TFS (Alt) to DT Valid

SCDD

SCLK High to DT Disable

RDV

RFS

(Multichannel, Frame Delay Zero) to DT Valid

CLKOUT

SCLK

TFS

OUT

RFS

OUT

ALTERNATE

FRAME MODE

SCS

SCH

SCDE

SCDH

SCDD

TDE

RDV

MULTICHANNEL MODE,

FRAME DELAY 0

(MFD = 0)

TFS

RFS

OUT

TFS

OUT

TDV

SCDV

SCP

SCK

SCP

TFS

RFS

ALTERNATE

FRAME MODE

RDV

MULTICHANNEL MODE,

FRAME DELAY 0

(MFD = 0)

TDV

TDE

Figure 24. Serial Ports

ADSP-2185L

REV. A

100-Lead LQFP Package Pinout

PIN 1
IDENTIFIER

TOP VIEW

(Not to Scale)

ADSP-2185L

D19

D18

D17

D16

IRQE

+PF4

IRQL0

+PF5

GND

IRQL1

+PF6

DT0

TFS0

SCLK0

VDD

DT1

TFS1

RFS1

DR1

GND

SCLK1

ERESET

RESET

D15

D14

D13

D12

GND

D11

D10

VDD

GND

D7/

IWR

D6/

IRD

D5/IAL
D4/

GND

VDD

D3/

IACK

D2/IAD15

D1/IAD14

D0/IAD13

BG
EBG

BR
EBR

A4/IAD3

A5/IAD4

GND

A6/IAD5

A7/IAD6

A8/IAD7

A9/IAD8

A10/IAD9

A11/IAD10

A12/IAD11

A13/IAD12

GND

CLKIN

XTAL

VDD

CLKOUT

GND

VDD

BMS

DMS
PMS

IOMS

CMS

IRQ2

+PF7

RFS0

DR0

EMS

ELOUT

ECLK

ELIN

EINT

A3/IAD2

A2/IAD1

A1/IAD0

PWDACK

BGH

FL0

FL1

FL2

D23

D22

D21

D20

GND

PF1 [MODE B]

GND

PWD

VDD

PF0 [MODE A]

PF2 [MODE C]

PF3

REV. A

ADSP-2185L

LQFP Pin Configurations

LQFP

Pin

LQFP

Pin

LQFP

Pin

LQFP

Pin

Number

Name

Number

Name

Number

Name

Number

Name

A4/IAD3

IRQE + PF4

EBR

D16

A5/IAD4

IRQL0 + PF5

D17

GND

EBG

D18

A6/IAD5

IRQL1 + PF6

D19

A7/IAD6

IRQ2 + PF7

D0/IAD13

GND

A8/IAD7

DT0

D1/IAD14

D20

A9/IAD8

TFS0

D2/IAD15

D21

A10/IAD9

RFS0

D3/IACK

D22

A11/IAD10

DR0

VDD

D23

A12/IAD11

SCLK0

GND

FL2

A13/IAD12

VDD

D4/IS

FL1

GND

DT1

D5/IAL

FL0

CLKIN

TFS1

D6/IRD

PF3

XTAL

RFS1

D7/IWR

PF2 [Mode C]

VDD

DR1

VDD

CLKOUT

GND

PWD

GND

SCLK1

VDD

GND

VDD

ERESET

PF1 [Mode B]

RESET

D10

PF0 [Mode A]

EMS

D11

BGH

BMS

GND

PWDACK

DMS

ECLK

D12

PMS

ELOUT

D13

A1/IAD0

IOMS

ELIN

D14

A2/IAD1

CMS

EINT

D15

100

A3/IAD2

The ADSP-2185L package pinout is shown in the table below. Pin names in bold text replace the plain text named functions when
Mode C = 1. A + sign separates two functions when either function can be active for either major I/O mode. Signals enclosed in
brackets [ ] are state bits latched from the value of the pin at the deassertion of RESET.

ADSP-2185L

REV. A

ORDERING GUIDE

Ambient

Instruction

Temperature

Rate

Package

Part Number

Range

(MHz)

Description

Option*

ADSP-2185LKST-115

C to +70

28.8

100-Lead LQFP

ST-100

ADSP-2185LBST-115

C to +85

28.8

100-Lead LQFP

ST-100

ADSP-2185LKST-133

C to +70

33.3

100-Lead LQFP

ST-100

ADSP-2185LBST-133

C to +85

33.3

100-Lead LQFP

ST-100

ADSP-2185LBST-160

C to +85

100-Lead LQFP

ST-100

ADSP-2185LKST-210

C to +70

100-Lead LQFP

ST-100

ADSP-2185LBST-210

C to +85

100-Lead LQFP

ST-100

*ST = Plastic Thin Quad Flatpack (LQFP).

OUTLINE DIMENSIONS

Dimensions shown in inches and (mm).

100-Lead Metric Thin Plastic Quad Flatpack (LQFP)

(ST-100)

SEATING

PLANE

0.030 (0.75)

0.024 (0.60) TYP

0.020 (0.50)

0.063 (1.60) MAX

12°
TYP

0.007 (0.177)

0.005 (0.127) TYP

0.003 (0.077)

6° ± 4°

0° 7°

0.004

(0.102)

MAX LEAD

COPLANARITY

TOP VIEW

(PINS DOWN)

100

0.011 (0.27)

0.009 (0.22) TYP

0.007 (0.17)

0.640 (16.25)

0.630 (16.00)

0.620 (15.75)

TYP SQ

0.020 (0.50)

BSC

LEAD PITCH

0.553 (14.05)

0.551 (14.00)

0.549 (13.95)

TYP SQ

0.472 (12.00) BSC

LEAD WIDTH

NOTE:
THE ACTUAL POSITION OF EACH LEAD IS WITHIN (0.08)
0.0032 FROM ITS IDEAL POSITION WHEN MEASURED IN THE
LATERAL DIRECTION.
CENTER FIGURES ARE TYPICAL UNLESS OTHERWISE NOTED

C3189a311/98

PRINTED IN U.S.A.

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: ADSP-2185LBST-115

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: ADSP-2185LBST-115