REV. 0
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
a
Precision Rail-to-Rail Input & Output
Operational Amplifiers
OP184/OP284/OP484
FEATURES
Single-Supply Operation
Wide Bandwidth: 4 MHz
Low Offset Voltage: 65 V
Unity-Gain Stable
High Slew Rate: 4.0 V/ s
Low Noise: 3.9 nV/
Hz
APPLICATIONS
Battery Powered Instrumentation
Power Supply Control and Protection
Telecom
DAC Output Amplifier
ADC Input Buffer
GENERAL DESCRIPTION
The OP184/OP284/OP484 are single, dual and quad single-
supply, 4 MHz bandwidth amplifiers featuring rail-to-rail inputs
and outputs. They are guaranteed to operate from +3 to +36 (or
1.5 to
18) volts and will function with a single supply as low
as +1.5 volts.
These amplifiers are superb for single supply applications re-
quiring both ac and precision dc performance. The combination
of bandwidth, low noise and precision makes the OP184/OP284/
OP484 useful in a wide variety of applications, including filters
and instrumentation.
Other applications for these amplifiers include portable telecom
equipment, power supply control and protection, and as amplifi-
ers or buffers for transducers with wide output ranges. Sensors
requiring a rail-to-rail input amplifier include Hall effect, piezo
electric, and resistive transducers.
The ability to swing rail-to-rail at both the input and output en-
ables designers to build multistage filters in single-supply sys-
tems and to maintain high signal-to-noise ratios.
The OP184/OP284/OP484 are specified over the HOT extended
industrial (40
C to +125
C) temperature range. The single
and dual are available in 8-pin plastic DIP plus SO surface
mount packages. The quad OP484 is available in 14-pin plastic
DIPs and 14-lead narrow-body SO packages.
PIN CONFIGURATIONS
8-Lead Epoxy DIP
(P Suffix)
8-Lead SO
(S Suffix)
1
2
3
4
8
7
6
5
OUT A
V+
NULL
NC
NULL
IN A
+IN A
V
OP184
NC = NO CONNECT
8-Lead Epoxy DIP
(P Suffix)
8-Lead SO
(S Suffix)
1
2
3
4
8
7
6
5
OP284
OUT B
IN B
+IN B
V+
OUT A
IN A
+IN A
V
14-Lead Epoxy DIP
(P Suffix)
14-Lead Narrow-Body SO
(S Suffix)
14
13
12
11
10
9
8
1
2
3
4
5
6
7
OP484
OUT A
IN A
+IN A
V+
+IN B
IN B
OUT B
OUT D
IN D
+IN D
V
+IN C
IN C
OUT C
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 617/329-4700
World Wide Web Site: http://www.analog.com
Fax: 617/326-8703
Analog Devices, Inc., 1996
OP184/OP284/OP484SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
Parameter
Symbol
Conditions
Min
Typ Max Units
INPUT CHARACTERISTICS
Offset Voltage "OP184/284E" Grade
V
OS
(Note 1)
65
V
40
C
T
A
+125
C
165
V
Offset Voltage "OP184/284F" Grade
V
OS
125
V
40
C
T
A
+125
C
350
V
Offset Voltage "OP484E" Grade
V
OS
75
V
40
C
T
A
+125
C
175
V
Offset Voltage "OP484F" Grade
V
OS
150
V
40
C
T
A
+125
C
450
V
Input Bias Current
I
B
60
350
nA
40
C
T
A
+125
C
575
nA
Input Offset Current
I
OS
2
50
nA
40
C
T
A
+125
C
50
nA
Input Voltage Range
0
+5
V
Common-Mode Rejection Ratio
CMRR
V
CM
= 0 V to 5 V
60
dB
Common-Mode Rejection Ratio
CMRR
V
CM
= 1.0 V to 4.0 V, 40
C
T
A
+125
C
86
dB
Large Signal Voltage Gain
A
VO
R
L
= 2 k
, 1 V
V
O
4 V
50
240
V/mV
R
L
= 2 k
, 40
C
T
A
+125
C
25
V/mV
Bias Current Drift
I
B
/
T
150
pA/
C
OUTPUT CHARACTERISTICS
Output Voltage High
V
OH
I
L
= 1.0 mA
+4.85
V
Output Voltage Low
V
OL
I
L
= 1.0 mA
125
mV
Output Current
I
OUT
6.5
mA
POWER SUPPLY
Power Supply Rejection Ratio
PSRR
V
S
= +2.0 V to +10 V, 40
C
T
A
+125
C
76
dB
Supply Current/Amplifier
I
SY
V
O
= 2.5 V, 40
C
T
A
+125
C
1.45
mA
Supply Voltage Range
V
S
+3
+36
V
DYNAMIC PERFORMANCE
Slew Rate
SR
R
L
= 2 k
1.65
2.4
V/
s
Settling Time
t
s
To 0.01%, 1.0 V Step
2.5
s
Gain Bandwidth Product
GBP
3.25
MHz
Phase Margin
o
45
Degrees
NOISE PERFORMANCE
Voltage Noise
e
n
p-p
0.1 Hz to 10 Hz
0.3
V p-p
Voltage Noise Density
e
n
f = 1 kHz
3.9
nV/
Hz
Current Noise Density
i
n
0.4
pA/
Hz
NOTES
1
Input Offset Voltage measurements are performed by automated test equipment approximately 0.5 seconds after application of power.
Specifications subject to change without notice.
REV. 0
2
(@ V
S
= +5.0 V, V
CM
= 2.5 V, T
A
= +25 C unless otherwise noted)
ELECTRICAL CHARACTERISTICS
Parameter
Symbol
Conditions
Min
Typ
Max
Units
INPUT CHARACTERISTICS
Offset Voltage "OP184/284E" Grade
V
OS
(Note 1)
65
V
40
C
T
A
+125
C
165
V
Offset Voltage "OP184/284F" Grade
V
OS
125
V
40
C
T
A
+125
C
350
V
Offset Voltage "OP484E" Grade
V
OS
100
V
40
C
T
A
+125
C
200
V
Offset Voltage "OP484F" Grade
V
OS
150
V
40
C
T
A
+125
C
450
V
Input Bias Current
I
B
60
350
nA
40
C
T
A
+125
C
575
nA
Input Offset Current
I
OS
40
C
T
A
+125
C
50
nA
Input Voltage Range
0
+3
V
Common-Mode Rejection Ratio
CMRR
V
CM
= 0 V to 3 V
60
dB
Common-Mode Rejection Ratio
CMRR
V
CM
= 0 V to 3 V, 40
C
T
A
+125
C
56
dB
OUTPUT CHARACTERISTICS
Output Voltage High
V
OH
I
L
= 1.0 mA
+2.85
V
Output Voltage Low
V
OL
I
L
= 1.0 mA
125
mV
POWER SUPPLY
Power Supply Rejection Ratio
PSRR
V
S
=
1.25 V to
1.75 V
76
dB
Supply Current/Amplifier
I
SY
V
O
= 1.5 V, 40
C
T
A
+125
C
1.35
mA
DYNAMIC PERFORMANCE
Gain Bandwidth Product
GBP
3
MHz
NOISE PERFORMANCE
Voltage Noise Density
e
n
f = 1 kHz
3.9
nV/
Hz
NOTES
1
Input Offset Voltage measurements are performed by automated test equipment approximately 0.5 seconds after application of power.
Specifications subject to change without notice.
REV. 0
3
OP184/OP284/OP484
(@ V
S
= +3.0 V, V
CM
= 1.5 V, T
A
= +25 C unless otherwise noted)
REV. 0
4
OP184/OP284/OP484
ELECTRICAL CHARACTERISTICS
Parameter
Symbol
Conditions
Min Typ
Max
Units
INPUT CHARACTERISTICS
Offset Voltage "OP184/284E" Grade V
OS
(Note 1)
100
V
40
C
T
A
+125
C
200
V
Offset Voltage "OP284F" Grade
V
OS
175
V
40
C
T
A
+125
C
375
V
Offset Voltage "OP484E" Grade
V
OS
150
V
40
C
T
A
+125
C
300
V
Offset Voltage "OP484F" Grade
V
OS
250
V
40
C
T
A
+125
C
500
V
Input Bias Current
I
B
80
350
nA
40
C
T
A
+125
C
575
nA
Input Offset Current
I
OS
40
C
T
A
+125
C
50
nA
Input Voltage Range
15
+15
V
Common-Mode Rejection Ratio
CMRR
V
CM
= 14.0 V to +14.0 V, 40
C
T
A
+125
C
86
90
dB
Common-Mode Rejection Ratio
CMRR
V
CM
= 15.0 V to +15.0 V
80
dB
Large Signal Voltage Gain
A
VO
R
L
= 2 k
, 10 V
V
O
10 V
150
1000
V/mV
R
L
= 2 k
, 40
C
T
A
+125
C
75
V/mV
Offset Voltage Drift "E" Grade
V
OS
/
T
0.2
2.00
V/
C
Bias Current Drift
I
B
/
T
150
pA/
C
OUTPUT CHARACTERISTICS
Output Voltage High
V
OH
I
L
= 1.0 mA
+14.8
V
Output Voltage Low
V
OL
I
L
= 1.0 mA
14.875 V
Output Current
I
OUT
10
mA
POWER SUPPLY
Power Supply Rejection Ratio
PSRR
V
S
=
2.0 V to
18 V, 40
C
T
A
+125
C
90
dB
Supply Current/Amplifier
I
SY
V
O
= 0 V, 40
C
T
A
+125
C
2.0
mA
Supply Current/Amplifier
I
SY
V
S
=
18 V, 40
C
T
A
+125
C
2.25
mA
DYNAMIC PERFORMANCE
Slew Rate
SR
R
L
= 2 k
2.4
4.0
V/
s
Full-Power Bandwidth
BWp
1% Distortion, R
L
= 2 k
, V
O
= 29 V p-p
35
kHz
Settling Time
t
S
To 0.01%, 10 V Step
4
s
Gain Bandwidth Product
GBP
4.25
MHz
Phase Margin
o
50
Degrees
NOISE PERFORMANCE
Voltage Noise
en p-p
0.1 Hz to 10 Hz
0.3
V p-p
Voltage Noise Density
en
f = 1 kHz
3.9
nV/
Hz
Current Noise Density
in
0.4
pA/
Hz
NOTES
1
Input Offset Voltage measurements are performed by automated test equipment approximately 0.5 seconds after application of power.
Specifications subject to change without notice.
WAFER TEST LIMITS
Parameter
Symbol
Conditions
Limit
Units
Offset Voltage OP284
V
OS
65
V max
Offset Voltage OP484
V
OS
75
V max
Input Bias Current
I
B
350
nA max
Input Offset Current
I
OS
50
nA max
Input Voltage Range
V
CM
V to V+
V min
Common-Mode Rejection Ratio
CMRR
V
CM
= +1 V to +4 V
86
dB min
Power Supply Rejection Ratio
PSRR
V
S
=
2 V to
18 V
90
dB min
Large Signal Voltage Gain
A
VO
R
L
= 2 k
50
V/mV min
Output Voltage High
V
OH
I
L
= 1.0 mA
4.85
V min
Output Voltage Low
V
OL
I
L
= 1.0 mA
125
mV max
Supply Current/Amplifier
I
SY
V
O
= 0 V, R
L
=
1.45
mA max
NOTE
Electrical tests and wafer probe to the limits shown. Due to variations in assembly methods and normal yield loss, yield after packaging is not guaranteed for standard
product dice. Consult factory to negotiate specifications based on dice lot qualifications through sample lot assembly and testing.
(@ V
S
= +5.0 V, V
CM
= 2.5 V, T
A
= +25 C unless otherwise noted)
(@ V
S
= 15.0 V, V
CM
= 0 V, T
A
= +25 C unless otherwise noted)
REV. 0
5
OP184/OP284/OP484
ABSOLUTE MAXIMUM RATINGS
1
Supply Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
18 V
Differential Input Voltage
2
. . . . . . . . . . . . . . . . . . . . .
0.6 V
Output Short-Circuit Duration to GND
3
. . . . . . . . Indefinite
Storage Temperature Range
P, S Packages . . . . . . . . . . . . . . . . . . . . . . 65
C to +150
C
Operating Temperature Range
OP184/OP284/OP484E, F . . . . . . . . . . . . 40
C to +125
C
Junction Temperature Range
P, S Packages . . . . . . . . . . . . . . . . . . . . . . 65
C to +150
C
Lead Temperature Range (Soldering 60 sec) . . . . . . . . +300
C
Package Type
JA
3
JC
Units
8-Pin Plastic DIP (P)
103
43
C/W
8-Pin SOIC (S)
158
43
C/W
14-Pin Plastic DIP (P)
83
39
C/W
14-Pin SOIC (S)
92
27
C/W
NOTES
1
Absolute maximum ratings apply to both DICE and packaged parts unless
otherwise noted.
2
For input voltages greater than 0.6 volts, the input current should be limited to less
than 5 mA to prevent degradation or destruction of the input devices.
3
JA
is specified for the worst case conditions; i.e.,
JA
is specified for device in socket
for cerdip and P-DIP packages;
JA
is specified for device soldered in circuit board
for SOIC package.
ORDERING GUIDE
Temperature
Package
Package
Model
Range
Description
Option
OP184EP
40
C to +125
C
8-Pin Plastic DIP
N-8
OP184ES
40
C to +125
C
8-Pin SOIC
SO-8
OP184FP
40
C to +125
C
8-Pin Plastic DIP
N-8
OP184FS
40
C to +125
C
8-Pin SOIC
SO-8
OP284EP
40
C to +125
C
8-Pin Plastic DIP
N-8
OP284ES
40
C to +125
C
8-Pin SOIC
SO-8
OP284FP
40
C to +125
C
8-Pin Plastic DIP
N-8
OP284FS
40
C to +125
C
8-Pin SOIC
SO-8
OP484EP
40
C to +125
C
14-Pin Plastic DIP N-14
OP484ES
40
C to +125
C
14-Pin SOIC
SO-14
OP484FP
40
C to +125
C
14-Pin Plastic DIP N-14
OP484FS
40
C to +125
C
14-Pin SOIC
SO-14
OP284 Die Size 0.065
0.092 Inch, 5,980 Sq. Mils
Substrate (Die Backside) Is Connected to V.
Transistor Count, 62.
OP484 Die Size 0.080
0.110 Inch, 8,800 Sq. Mils
Substrate (Die Backside) Is Connected to V.
Transistor Count, 120.
R3
Q1
IN
+IN
QL1
QL2
Q4
Q3
Q2
QB5
QB6
RB2
QB3
R1
Q5
R2
QB4
JB2
QB1
CB1 N+
P+
M
QB2
CC1
Q9
Q7
Q11
Q8
Q6
Q10
Q12
QB7
QB8
QB9
RB1
JB1
TP
R4
R5
R6
RB3
C FF
R7
R8
Q13
Q14
R10
Q15
RB4
QB10
CC2
C O
Q17
Q16
R11
Q18
V
CC
OUT
V
EE
R9
Figure 1. Simplified Schematic
INPUT OFFSET VOLTAGE V
QUANTITY
300
0
100 75
100
50
25
0
25
50
75
270
180
90
60
30
240
210
120
150
V
S
= +3V
T
A
= +25
C
V
CM
= 1.5V
Figure 2. Input Offset Voltage
Distribution
INPUT OFFSET VOLTAGE V
QUANTITY
300
0
100 75
100
50
25
0
25
50
75
270
180
90
60
30
240
210
120
150
V
S
= +5V
T
A
= +25
C
V
CM
= 2.5V
Figure 3. Input Offset Voltage
Distribution
INPUT OFFSET VOLTAGE V
QUANTITY
200
0
125 100
125
75 50
0
50 75 100
175
100
75
50
25
150
125
V
S
=
15V
T
A
= +25
C
25
25
Figure 4. Input Offset Voltage
Distribution
6
OFFSET VOLTAGE DRIFT, TCV
OS
V/
C
QUANTITY
300
0
0
0.25
1.5
0.50
0.75
1.0
1.25
250
200
150
100
50
V
S
= +5V
40
C
T
A
+125
C
Figure 5. Input Offset Voltage Drift
Distribution
OFFSET VOLTAGE DRIFT, TCV
OS
V/
C
QUANTITY
300
0
0
0.25
1.5
0.50
0.75
1.0
1.25
250
200
150
100
50
V
S
=
15V
40
C
T
A
+125
C
Figure 6. Input Offset Voltage Drift
Distribution
TEMPERATURE
C
INPUT BIAS CURRENT nA
40
80
40
125
25
85
45
50
55
60
65
70
75
V
S
= +5V
V
S
=
15V
V
CM
= V
S
/ 2
Figure 7. Bias Current vs.
Temperature
COMMON MODE VOLTAGE Volts
INPUT BIAS CURRENT nA
500
500
15
10
15
5
5
10
0
400
300
200
100
0
100
200
300
400
V
S
=
15V
Figure 8. Input Bias Current vs.
Common-Mode Voltage
LOAD CURRENT mA
OUTPUT VOLTAGE mV
1,000
100
10
0.01
0.1
10
1
SOURCE
SINK
V
S
=
15V
Figure 9. Output Voltage to Supply
Rail vs. Load Current
TEMPERATURE
C
SUPPLY CURRENT/AMPLIFIER mA
1.2
0.5
1.1
0.8
0.7
0.6
1.0
0.9
40
125
25
85
V
S
=
15V
V
S
= +5V
V
S
= +3V
Figure 10. Supply Current vs.
Temperature
OP184/OP284/OP484Typical Performance Characteristics
REV. 0
REV. 0
7
OP184/OP284/OP484
SUPPLY VOLTAGE Volts
SUPPLY CURRENT (PER AMPLIFIER) mA
1.50
0
0
2.5
20
5.0
10
12.5
15
1.25
1.0
0.75
0.5
0.25
17.5
7.5
T
A
= +25
C
Figure 11. Supply Current vs. Supply
Voltage
TEMPERATURE
C
SHORT CIRCUIT CURRENT mA
50
0
50
125
40
30
20
10
V
S
=
15V
25
0
25
75
50
100
V
S
= +5V, V
CM
= +2.5V
+I
SC
I
SC
I
SC
+I
SC
Figure 12. Short Circuit Current vs.
Temperature
0
45
90
135
180
225
270
PHASE SHIFT Degrees
FREQUENCY Hz
OPEN-LOOP GAIN dB
60
10k
100k
10M
1M
40
20
0
20
80
50
10
30
10
30
V
S
= +5V
T
A
= +25
C
NO LOAD
Figure 13. Open-Loop Gain and Phase
vs. Frequency (No Load)
0
45
90
135
180
225
270
PHASE SHIFT Degrees
FREQUENCY Hz
OPEN-LOOP GAIN dB
60
10k
100k
10M
1M
40
20
0
20
80
50
10
30
10
30
V
S
= +3V
T
A
= +25
C
NO LOAD
Figure 14. Open-Loop Gain and Phase
vs. Frequency (No Load)
0
45
90
135
180
225
270
PHASE SHIFT Degrees
FREQUENCY Hz
OPEN-LOOP GAIN dB
60
10k
100k
10M
1M
40
20
0
20
80
50
10
30
10
30
V
S
=
15V
T
A
= +25
C
NO LOAD
Figure 15. Open-Loop Gain and Phase
vs. Frequency (No Load)
TEMPERATURE
C
OPEN-LOOP GAIN V/mV
2.5k
0
50
125
2k
1.5k
1k
500
V
S
=
15V
10V < V
O
< 10V
R
L
= 2k
25
0
25
75
50
100
V
S
= +5V
1V < V
O
< 4V
R
L
= 2k
Figure 16. Open-Loop Gain vs.
Temperature
FREQUENCY Hz
30
10
CLOSED-LOOP GAIN dB
40
60
10
40
100
10k
1M
10M
10
V
S
= +5V
R
L
= 2k
T
A
= +25
C
20
30
0
20
50
1k
100k
Figure 17. Closed-Loop Gain vs.
Frequency (2 k
Load)
FREQUENCY Hz
30
10
CLOSED-LOOP GAIN dB
40
60
10
40
100
10k
1M
10M
10
V
S
=
15V
R
L
= 2k
T
A
= +25
C
20
30
0
20
50
1k
100k
Figure 18. Closed-Loop Gain vs.
Frequency (2 k
Load)
FREQUENCY Hz
30
10
CLOSED-LOOP GAIN dB
40
60
10
40
100
10k
1M
10M
10
V
S
= +3V
R
L
= 2k
T
A
= +25
C
20
30
0
20
50
1k
100k
Figure 19. Closed-Loop Gain vs.
Frequency (2 k
Load)
FREQUENCY Hz
210
100
OUTPUT IMPEDANCE
240
300
150
0
1k
100k
10M
90
V
S
= +5V
T
A
= +25
C
60
30
120
180
270
10k
1M
A
V
= 100
A
V
= 1
A
V
= 10
Figure 20. Output Impedance vs.
Frequency
FREQUENCY Hz
210
100
OUTPUT IMPEDANCE
240
300
150
0
1k
100k
10M
90
V
S
=
15V
T
A
= +25
C
60
30
120
180
270
10k
1M
A
V
= 100
A
V
= 1
A
V
= 10
Figure 21. Output Impedance vs.
Frequency
FREQUENCY Hz
210
100
OUTPUT IMPEDANCE
240
300
150
0
1k
100k
10M
90
V
S
= +3V
T
A
= +25
C
60
30
120
180
270
10k
1M
A
V
= 100
A
V
= 1
A
V
= 10
Figure 22. Output Impedance vs.
Frequency
FREQUENCY Hz
3
1k
MAXIMUM OUTPUT SWING Vp-p
4
5
2
0
10k
100k
1M
10M
1
V
S
= +5V
V
IN
= 0.54.5V
R
L
= 2k
T
A
= +25
C
Figure 23. Maximum Output Swing
vs. Frequency
FREQUENCY Hz
20
1k
MAXIMUM OUTPUT SWING Vp-p
25
30
15
5
0
10k
100k
1M
10M
10
V
S
=
15V
V
IN
=
14V
R
L
= 2k
T
A
= +25
C
Figure 24. Maximum Output Swing
vs. Frequency
FREQUENCY Hz
120
100
CMRR dB
140
180
80
20
1k
100k
10M
40
20
0
60
100
160
10k
1M
V
S
=
15V
V
S
= +5V
T
A
= +25
C
V
S
= +3V
Figure 25. CMRR vs. Frequency
FREQUENCY Hz
100
100
PSRR dB
120
160
60
40
1k
100k
10M
20
T
A
= +25
C
0
20
40
80
140
10k
1M
V
S
=
15V
V
S
= +5V
V
S
= +3V
Figure 26. PSRR vs. Frequency
CAPACITIVE LOAD pF
OVERSHOOT %
80
70
0
10
100
1000
60
50
40
30
20
10
OS
+OS
V
S
=
2.5V
T
A
= +25
C, A
VCL
= 1
V
IN
=
50mV
Figure 27. Small Signal Overshoot
vs. Capacitive Load
TEMPERATURE
C
SLEW RATE V/s
7
0
50
125
25
0
75
100
6
3
2
1
5
4
25
50
+SLEW RATE
SLEW RATE
V
S
=
15V
R
L
= 2k
V
S
= +5V
R
L
= 2k
+SLEW RATE
SLEW RATE
Figure 28. Slew Rate vs. Temperature
REV. 0
8
OP184/OP284/OP484Typical Performance Characteristics
REV. 0
9
OP184/OP284/OP484
30
0
1000
15
5
10
25
20
100
10
FREQUENCY Hz
1
2.5V
V
S
15V
T
A
= +25
C
NOISE DENSITY nV/
Hz
Figure 29. Voltage Noise Density
vs. Frequency
10
0
1000
6
2
4
8
100
10
FREQUENCY Hz
1
CURRENT NOISE DENSITY pA/
Hz
2.5V
V
S
15V
T
A
= +25
C
Figure 30. Current Noise Density
vs. Frequency
SETTLING TIME s
STEP SIZE Volts
5
5
0
1
6
2
4
4
3
2
1
0
5
3
1
2
3
4
V
S
= +5V
T
A
= +25
C
0.1%
0.01%
Figure 31. Settling Time vs. Step Size
SETTLING TIME s
STEP SIZE Volts
10
10
0
1
6
2
4
8
6
4
2
0
5
3
2
4
6
8
V
S
=
15V
T
A
= +25
C
0.1%
0.01%
Figure 32. Settling Time vs. Step Size
10
0%
100
90
1s
10mV
V
S
=
15V
A
V
= 100k
e
n
= 0.3Vp-p
Figure 33. 0.1 Hz to 10 Hz Noise
10
0%
100
90
1s
V
S
= +5V, 0V
A
V
= 100k
e
n
= 0.3Vp-p
10mV
Figure 34. 0.1 Hz to 10 Hz Noise
FREQUENCY Hz
100
100
120
160
60
40
1k
100k
10M
20
0
20
40
80
140
10k
1M
V
S
=
15V
V
S
= +3V
T
A
= +25
C
CHANNEL SEPARATION dB
Figure 35. Channel Separation
vs. Frequency
10
0%
100
90
1s
100mV
V
S
= +5V
A
V
= 1
R
L
= OPEN
C
L
= 300pF
T
A
= +25
C
+400mV
0V
Figure 36. Small Signal Transient
Response
10
0%
100
90
1s
100mV
V
S
= +5V
A
V
= 1
R
L
= 2k
C
L
= 300pF
T
A
- +25
C
400mV
0V
Figure 37. Small Signal Transient
Response
REV. 0
10
OP184/OP284/OP484
FREQUENCY Hz
THD+N %
0.1
0.010
0.0005
20
100
10k
1k
0.001
20k
V
O
=
0.75V
V
O
=
2.5V
V
O
=
1.5V
A
V
= 1000
V
S
=
2.5V
R
L
= 2k
Figure 40. Total Harmonic Distortion
vs. Frequency
10
0%
100
90
500ns
100mV
V
S
=
1.5V
A
V
= 1
NO LOAD
T
A
= +25
C
200mV
0V
200mV
Figure 38. Small Signal Transient
Response
200mV
0V
200mV
10
0%
100
90
1s
100mV
V
S
=
0.75V
A
V
= 1
NO LOAD
T
A
= +25
C
Figure 39. Small Signal Transient
Response
APPLICATIONS
Functional Description
The OP284 and OP484 are precision single-supply, rail-to-rail
operational amplifiers. Intended for the portable instrumenta-
tion marketplace, the OP184/OP284/OP484 combines the at-
tributes of precision, wide bandwidth, and low noise to make it
a superb choice in those single supply applications that require
both ac and precision dc performance. Other low supply voltage
applications for which the OP284 is well suited are active filters,
audio microphone preamplifiers, power supply control, and tele-
com. To combine all of these attributes with rail-to-rail input/
output operation, novel circuit design techniques are used.
D1
D2
Q4
R2
4k
V
POS
I1
R1
4k
Q3
Q1
Q2
R4
3k
I2
R3
3k
V
01
IN
V
02
V
NEG
+IN
Figure 41. OP284 Equivalent Input Circuit
For example, Figure 41 illustrates a simplified equivalent circuit
for the OP184/OP284/OP484's input stage. It is comprised of
an NPN differential pair, Q1-Q2, and a PNP differential pair,
Q3-Q4, operating concurrently. Diode network D1-D2 serves
to clamp the applied differential input voltage to the OP284,
thereby protecting the input transistors against avalanche dam-
age. Input stage voltage gains are kept low for input rail-to-rail
operation. The two pairs of differential output voltages are con-
nected to the OP284's second stage, which is a compound folded
cascode gain stage. It is also in the second gain stage where the
two pairs of differential output voltages are combined into a
single-ended output signal voltage used to drive the output
stage. A key issue in the input stage is the behavior of the input
bias currents over the input common-mode voltage range. Input
bias currents in the OP284 are the arithmetic sum of the base
currents in Q1-Q3 and in Q2-Q4. As a result of this design
approach, the input bias currents in the OP284 not only exhibit
different amplitudes, but also exhibit different polarities. This
effect is best illustrated in Figure 8. It is, therefore, of para-
mount importance that the effective source impedances con-
nected to the OP284's inputs be balanced for optimum dc and
ac performance.
To achieve rail-to-rail output, the OP284 output stage design
employs a unique topology for both sourcing and sinking cur-
rent. This circuit topology is illustrated in Figure 42. As previ-
ously mentioned, the output stage is voltage-driven from the
second gain stage. The signal path through the output stage is
inverting; that is, for positive input signals, Q1 provides the base
current drive to Q6 so that it conducts (sinks) current. For
negative input signals, the signal path via Q1-Q2-D1-Q4-Q3
provides the base current drive for Q5 to conduct (source) cur-
rent. Both amplifiers provide output current until they are
forced into saturation, which occurs at approximately 20 mV
from negative rail and 100 mV from the positive supply rail.
V
POS
I2
I1
Q1
Q3
Q4
Q2
V
NEG
Q5
V
OUT
Q6
R6
R3
R2
R1
R4
INPUT FROM
SECOND GAIN
STAGE
R5
D1
Figure 42. OP284 Equivalent Output Circuit
REV. 0
11
OP184/OP284/OP484
Thus, the saturation voltage of the output transistors sets the
limit on the OP284's maximum output voltage swing. Output
short circuit current limiting is determined by the maximum
signal current into the base of Q1 from the second gain stage.
Under output short circuit conditions, this input current level is
approximately 100
A. With transistor current gains around
200, the short circuit current limits are typically 20 mA. The
output stage also exhibits voltage gain. This is accomplished by
use of common-emitter amplifiers, and as a result, the voltage
gain of the output stage (thus, the open-loop gain of the device)
exhibits a dependence to the total load resistance at the output
of the OP284.
Input Overvoltage Protection
As with any semiconductor device, if conditions exist where the
applied input voltages to the device exceed either supply voltage,
the device's input overvoltage I-V characteristic must be consid-
ered. When an overvoltage occurs, the amplifier could be dam-
aged, depending on the magnitude of the applied voltage and
the magnitude of the fault current. Figure 43 illustrates the over
voltage I-V characteristic of the OP284. This graph was gener-
ated with the supply pins connected to GND and a curve
tracer's collector output drive connected to the input.
5
4
3
2
1
0
1
2
3
4
5
5
4
3
2
1
0
1
2
3
4
5
INPUT CURRENT mA
INPUT VOLTAGE Volts
Figure 43. Input Overvoltage I-V Characteristics of the
OP284
As shown in the figure, internal p-n junctions to the OP284 en-
ergize and permit current flow from the inputs to the supplies
when the input is 1.8 V more positive and 0.6 V more negative
than the respective supply rails. As illustrated in the simplified
equivalent circuit shown in Figure 41, the OP284 does not have
any internal current limiting resistors; thus, fault currents can
quickly rise to damaging levels.
This input current is not inherently damaging to the device,
provided that it is limited to 5 mA or less. For the OP284, once
the input exceeds the negative supply by 0.6 V, the input cur-
rent quickly exceeds 5 mA. If this condition continues to exist,
an external series resistor should be added at the expense of ad-
ditional thermal noise. Figure 44 illustrates a typical noninvert-
ing configuration for an overvoltage protected amplifier where
the series resistance, R
S
, is chosen such that:
R
S
=
V
IN ( MAX )
V
SUPPLY
5 mA
R1
R2
V
IN
V
OUT
1/2
OP284
Figure 44. A Resistance in Series with an Input Limits
Overvoltage Currents to Safe Values
For example, a 1 k
resistor will protect the OP284 against
input signals up to 5 V above and below the supplies. For other
configurations where both inputs are used, then each input
should be protected against abuse with a series resistor. Again,
in order to ensure optimum dc and ac performance, it is recom-
mended to balance source impedance levels. For more informa-
tion on the general overvoltage characteristics of amplifiers,
please refer to the 1993 System Applications Guide, Section 1,
pages 56-69. This reference textbook is available from the Ana-
log Devices Literature Center.
Output Phase Reversal
Some operational amplifiers designed for single-supply opera-
tion exhibit an output voltage phase reversal when their inputs
are driven beyond their useful common-mode range. Typically
for single-supply bipolar op amps, the negative supply deter-
mines the lower limit of their common-mode range. With these
devices, external clamping diodes, with the anode connected to
ground and the cathode to the inputs, prevent input signal ex-
cursions from exceeding the device's negative supply (i.e.,
GND), preventing a condition that could cause the output volt-
age to change phase. JFET-input amplifiers may also exhibit
phase reversal, and, if so, a series input resistor is usually re-
quired to prevent it.
The OP284 is free from reasonable input voltage range restric-
tions, provided that input voltages no greater than the supply
voltages are applied. Although the device's output will not
change phase, large currents can flow through the input protec-
tion diodes as was shown in Figure 43. Therefore, the technique
recommended in the Input Overvoltage Protection section
should be applied to those applications where the likelihood of
input voltages exceeding the supply voltages is high.
Designing Low Noise Circuits in Single Supply Applications
In single supply applications, devices like the OP284 extend the
dynamic range of the application through the use of rail-to-rail
operation. In fact, the OP284 family is the first of its kind to
combine single supply, rail-to-rail operation and low noise in
one device. It is the first device in the industry to exhibit an
input noise voltage spectral density of less than 4 nV/
Hz
at
1 kHz. It was also designed specifically for low-noise, single-
supply applications, and as such, some discussion on circuit
noise concepts in single supply applications is appropriate.
REV. 0
12
OP184/OP284/OP484
Referring to the op amp noise model circuit configuration illus-
trated in Figure 45, the expression for an amplifier's total
equivalent input noise voltage for a source resistance level R
S
is
given by:
e
nT
=
2 e
nR
( )
2
+
i
nOA
R
(
)
2
[
]
+
e
nOA
(
)
2
, units in V
Hz
where R
S
= 2R = Effective, or equivalent, circuit source
resistance,
(e
nOA
)
2
= Op amp equivalent input noise voltage spectral
power (1 Hz BW),
(i
nOA
)
2
= Op amp equivalent input noise current spectral
power (1 Hz BW),
(e
nR
)
2
= Source resistance thermal noise voltage power =
(4kTR),
k = Boltzmann's constant = 1.38
10
23
J/K, and
T = Ambient temperature of the circuit, in Kelvin, =
273.15 + T
A
(
C)
i
NOA
e
NR
e
NOA
R
"NOISELESS"
i
NOA
e
NR
R
"NOISELESS"
IDEAL
NOISELESS
OP AMP
R
S
= 2R
Figure 45. Op Amp Noise Circuit Model Used to
Determine Total Circuit Equivalent Input Noise Voltage
and Noise Figure
As a design aid, Figure 46 illustrates the total equivalent input
noise of the OP284 and the total thermal noise of a resistor for
comparison. Note that for source resistance less than 1 k
, the
equivalent input noise voltage of the OP284 is dominant.
TOTAL SOURCE RESISTANCE, R
S
100
100
EQUIVALENT THERMAL NOISE nV/
Hz
1k
10k
100k
10
1
OP284 TOTAL
EQUIVALENT NOISE
RESISTOR THERMAL
NOISE ONLY
FREQUENCY = 1kHz
T
A
= +25
C
Figure 46. OP284 Total Noise vs. Source Resistance
Since circuit SNR is the critical parameter in the final analysis,
the noise behavior of a circuit is often expressed in terms of its
noise figure, NF. Noise figure is defined as the ratio of a
circuit's output signal-to-noise to its input signal-to-noise. An
expression of a circuit's NF in dB, and in terms of the opera-
tional amplifier's voltage and current noise parameters defined
previously, is given by:
NF (dB)
=
10 log 1
+
e
nOA
(
)
2
+
i
nOA
R
S
(
)
2
e
nRS
(
)
2
where NF (dB) = Noise figure of the circuit, expressed in dB,
R
S
= Effective, or equivalent, source resistance presented
to amplifier,
(e
nOA
)
2
= OP284 noise voltage spectral power (1 Hz BW),
(i
nOA
)
2
= OP284 noise current spectral power (1 Hz BW),
(e
nRS
)
2
= Source resistance thermal noise voltage power
= (4kTR
S
),
Circuit noise figure is straightforward to calculate because the
signal level in the application is not required to determine it.
However, many designers using NF calculations as the basis for
achieving optimum SNR believe that low noise figure is equal to
low total noise. In fact, the opposite is true, as illustrated in
Figure 47. Here, the noise figure of the OP284 is expressed as a
function of the source resistance level. Note that the lowest
noise figure for the OP284 occurs at a source resistance level of
10 k
. However, Figure 46 shows that this source resistance
level and the OP284 generate approximately 14 nV/
Hz
of total
equivalent circuit noise. Signal levels in the application would
invariably be increased to maximize circuit SNR--not an option
in low voltage, single supply applications.
TOTAL SOURCE RESISTANCE, R
S
6
100
NOISE FIGURE dB
1k
10k
100k
4
2
0
9
10
8
7
5
3
1
FREQUENCY = 1kHz
T
A
= +25
C
Figure 47. OP284 Noise Figure vs. Source Resistance
In single supply applications, therefore, it is recommended for
optimum circuit SNR to choose an operational amplifier with
the lowest equivalent input noise voltage and to choose source
resistance levels consistent in maintaining low total circuit noise.
REV. 0
13
OP184/OP284/OP484
Overdrive Recovery
The overdrive recovery time of an operational amplifier is the
time required for the output voltage to recover to its linear re-
gion from a saturated condition. The recovery time is important
in applications where the amplifier must recover quickly after a
large transient event. The circuit shown in Figure 48 was used
to evaluate the OP284's overload recovery time. The OP284
takes approximately 2
s to recover from positive saturation and
approximately 1
s to recover from negative saturation.
V
OUT
2
3
1
+5V
1/2
OP284
8
4
R3
9k
R1
10k
R2
10k
V
IN
10V STEP
5V
Figure 48. Output Overload Recovery Test Circuit
A Single-Supply, +3 V Instrumentation Amplifier
The OP284's low noise, wide bandwidth, and rail-to-rail input/
output operation makes it ideal for low supply voltage applica-
tions such as in a two op amp instrumentation amplifier as
shown in Figure 49. The circuit uses the classic two op amp in-
strumentation amplifier topology with four resistors to set the
gain. The transfer equation of the circuit is identical to that of a
noninverting amplifier. Resistors R2 and R3 should be closely
matched to each other as well as to resistors (R1 + P1) and R4
to ensure good common-mode rejection performance. Resistor
networks should be used in this circuit for R2 and R3 because
they exhibit the necessary relative tolerance matching for good
performance. Matched networks also exhibit tight relative resis-
tor temperature coefficients for good circuit temperature stabil-
ity. Trimming potentiometer P1 is used for optimum dc CMR
adjustment, and C1 is used to optimize ac CMR. With the cir-
cuit values as shown, circuit CMR is better than 80 dB over the
frequency range of 20 Hz to 20 kHz. Circuit RTI (Referred-to-
Input) noise in the 0.1 Hz to 10 Hz band is an impressively low
0.45
V p-p. Resistors RP1 and RP2 serve to protect the
OP284's inputs against input overvoltage abuse. Capacitor C2
can be included to the limit circuit bandwidth and, therefore,
wide bandwidth noise in sensitive applications. The value of
this capacitor should be adjusted depending on the required
closed-loop bandwidth of the circuit. The R4-C2 time constant
creates a pole at a frequency equal to:
f ( 3 dB)
=
1
2
R4 C2
V
OUT
R3
1.1k
5
6
7
+3V
A2
A1, A2 = 1/2 OP284
GAIN = 1 +
R4
R3
SET R2 = R3
R1 + P1 = R4
8
4
R4
10k
C2
RP1
1k
RP2
1k
R2
1.1k
R1
9.53k
P1
500
3
2
1
C1
AC CMRR
TRIM
5pF40pF
A1
V
IN
Figure 49. A Single Supply, +3 V Low Noise Instrumenta-
tion Amplifier
A +2.5 V Reference from a +3 V Supply
In many single-supply applications, the need for a 2.5 V refer-
ence often arises. Many commercially available monolithic
2.5 V references require at least a minimum operating supply of
4 V. The problem is exacerbated when the minimum operating
supply voltage is +3 V. The circuit illustrated in Figure 50 is an
example of a +2.5 V reference that operates from a single +3 V
supply. The circuit takes advantage of the OP284's rail-to-rail
input/output voltage ranges to amplify an AD589's 1.235 V
output to +2.5 V. The OP284's low TCV
OS
of 1.5
V/
C helps
maintain an output voltage temperature coefficient that is domi-
nated by the temperature coefficients of R2 and R3. In this
circuit with 100 ppm/
C TCR resistors, the output voltage
exhibits a temperature coefficient of 200 ppm/
C. Lower tempco
resistors are recommended for more accurate performance over
temperature.
One measure of the performance of a voltage reference is its
capacity to recover from sudden changes in load current. While
sourcing a steady-state load current of 1 mA, this circuit recov-
ers to 0.01% of the programmed output voltage in 1.5
s for a
total change in load current of
1 mA.
+2.5V
REF
P1
5k
3
2
1
+3V
1/2
OP284
8
4
R2
100k
R3
100k
+3V
0.1F
R1
17.4k
AD589
RESISTORS = 1%, 100ppm/
C
POTENTIOMETER = 10 TURN, 100ppm/
C
Figure 50. A +2.5 V Reference that Operates on a Single
+3 V Supply
REV. 0
14
OP184/OP284/OP484
A +5 V Only, 12-Bit DAC Swings Rail-to-Rail
The OP284 is ideal for use with a CMOS DAC to generate a
digitally-controlled voltage with a wide output range. Figure 51
shows a DAC8043 used in conjunction with the AD589 to gen-
erate a voltage output from 0 V to 1.23 V. The DAC is actually
operating in "voltage switching" mode where the reference is
connected to the current output, I
OUT
, and the output voltage is
taken from the V
REF
pin. This topology is inherently noninvert-
ing as opposed to the classic current output mode, which is
inverting and not usable in single supply applications.
V
OUT
= (5V)
D
4096
R4
100k
1%
3
2
1
+5V
1/2
OP284
8
4
R2
32.4k
1%
R3
232
1%
R1
17.8k
AD589
GND CLK SR1
LD
V
REF
R
FB
V
DD
I
OUT
1.23V
4
7
6
5
8
2
1
3
DAC8043
+5V
DIGITAL
CONTROL
Figure 51. A +5 V Only, 12-Bit DAC Swings Rail-to-Rail
In this application the OP284 serves two functions. First, it
buffers the high output impedance of the DAC's V
REF
pin,
which is on the order of 10 k
. The op amp provides a low
impedance output to drive any following circuitry. Second, the
op amp amplifies the output signal to provide a rail-to-rail out-
put swing. In this particular case, the gain is set to 4.1 so that
the circuit generates a 5 V output when the DAC output is at
full scale. If other output voltage ranges are needed, such as 0 V
V
OUT
4.095 V, the gain can be easily changed by adjusting
the values of R2 and R3.
A High-Side Current Monitor
In the design of power supply control circuits, a great deal of
design effort is focused on ensuring a pass transistor's long-term
reliability over a wide range of load current conditions. As a
result, monitoring and limiting device power dissipation is of
prime importance in these designs. The circuit illustrated in
Figure 52 is an example of a +3 V, single-supply high-side cur-
rent monitor that can be incorporated into the design of a volt-
age regulator with fold-back current limiting or a high current
power supply with crowbar protection. This design uses an
OP284's rail-to-rail input voltage range to sense the voltage
drop across a 0.1
current shunt. A p-channel MOSFET used
as the feedback element in the circuit converts the op amp's dif-
ferential input voltage into a current. This current is applied to
R2 to generate a voltage that is a linear representation of the
load current. The transfer equation for the current monitor is
given by:
Monitor Output
=
R2
R
SENSE
R1
I
L
For the element values shown, the Monitor Output's transfer
characteristic is 2.5 V/A.
8
1
4
3
+3V
0.1F
R
SENSE
0.1
+3V
I
L
G
S
D
1/2
AD284
2
M1
Si9433
MONITOR
OUTPUT
+3V
R2
2.49k
R1
100
Figure 52. A High-Side Load Current Monitor
Capacitive Load Drive Capability
The OP284 exhibits excellent capacitive load driving capabili-
ties. It can drive up to 1 nF as shown in Figure 27. Even
though the device is stable, a capacitive load does not come
without penalty in bandwidth. The bandwidth is reduced to
under 1 MHz for loads greater than 2 nF. A "snubber" network
on the output does not increase the bandwidth, but it does sig-
nificantly reduce the amount of overshoot for a given capacitive
load. A snubber consists of a series R-C network (R
S
, C
S
), as
shown in Figure 53, connected from the output of the device to
ground. This network operates in parallel with the load capaci-
tor, C
L
, to provide the necessary phase lag compensation. The
value of the resistor and capacitor is best determined empirically.
+5V
1/2
OP284
R
S
50
C
L
1nF
C
S
100nF
V
IN
100mVp-p
0.1F
V
OUT
Figure 53. Snubber Network Compensates for Capacitive
Load
The first step is to determine the value of the resistor R
S
. A
good starting value is 100
(typically, the optimum value will
be less than 100
). This value is reduced until the small-signal
transient response is optimized. Next, C
S
is determined--10
F
is a good starting point. This value is reduced to the smallest
value for acceptable performance (typically, 1
F). For the case
of a 10 nF load capacitor on the OP284, the optimal snubber
network is a 20
in series with 1
F. The benefit is immedi-
ately apparent as shown in the scope photo in Figure 54. The
top trace was taken with a 1 nF load, and the bottom trace was
taken with the 50
, 100 nF snubber network in place. The
amount of overshoot and ringing is dramatically reduced. Table I
below illustrates a few sample snubber networks for large load
capacitors.
REV. 0
15
OP184/OP284/OP484
10
0%
100
90
1nF LOAD
ONLY
SNUBBER
IN
CIRCUIT
2s
50mv
50mv
s
Figure 54. Overshoot and Ringing Is Reduced by Adding a
"Snubber" Network in Parallel with the 1 nF Load
Table I. Snubber Networks for Large Capacitive Loads
Load Capacitance
Snubber Network
(C
L
)
(R
S
, C
S
)
1 nF
50
, 100 nF
10 nF
20
, 1
F
100 nF
5
, 10
F
A Low Dropout Regulator with Current Limiting
Many circuits require stable regulated voltages relatively close,
in potential to an unregulated input source. This "low dropout"
type of regulator is readily implemented with a rail-to-rail out-
put op amp such as the OP284 because the wide output swing
allows easy drive to a low saturation voltage pass device. Fur-
thermore, it is particularly useful when the op amp also enjoys a
rail-rail input feature, as this factor allows it to perform high-
side current sensing for positive rail current limiting. Typical ex-
amples are voltages developed from 3 V to 9 V range system
sources or anywhere where low dropout performance is required
for power efficiency. The 4.5 V case here works from 5 V nomi-
nal sources with worst-case levels down to 4.6 V or less.
Figure 55 shows such a regulator set up using an OP284 plus a
low R
DS(ON)
, P-channel MOSFET pass device. Part of the low
dropout performance of this circuit is provided by Q1, which
has a rating of 0.11
with a gate drive voltage of only 2.7 V.
This relatively low gate drive threshold allows operation of the
regulator on supplies as low as 3 V without compromising over-
all performance.
The circuit's main voltage control loop operation is provided by
U1B, half of the OP284. This voltage control amplifier ampli-
fies the 2.5 V reference voltage produced by three terminal U2,
a REF192. The regulated output voltage V
OUT
is then:
V
OUT
=
V
OUT 2
1
+
R2
R 3
(
)
For this example, since V
OUT
of 4.5 V with V
OUT2
= 2.5 V re-
quires a U1B gain of 1.8 times, R3 and R2 are chosen for a ratio
of 1.2:1 or 10.0 k
:8.06 k
(using closest 1% values). Note
that for the lowest V
OUT
dc error, R2 R3 should be maintained
equal to R1 (as here), and the R2-R3 resistors should be stable,
close tolerance metal film types. The table in Figure 55 sum-
marizes R1-R3 values for some popular voltages. However,
note that, in general, the output can be anywhere between
V
OUT2
and the 12 V maximum rating of Q1.
While the low voltage saturation characteristic of Q1 is a key
part of the low dropout, another component is a low current
sense comparison threshold with good dc accuracy. Here, this
is provided by current sense amplifier U1A, which is provided
by a 20 mV reference from the 1.235 V AD589 reference diode
D2 and the R7-R8 divider. When the product of the output
current and the R
S
value match this voltage threshold, the cur-
rent control loop is activated, and U1A drives Q1's gate through
D1. This causes the overall circuit operation to enter current
mode control with a current limit I
LIMIT
defined as:
I
LIMIT
=
V
R(D2)
R
S
R7
R7
+
R8
(
)
R9
27.4k
C4
0.1F
C 5
0.01F
R11
1k
R6
4.99k
R8
301k
+V
S
R10
1k
R2
8.06k
C3
0.1F
R
S
0.05
C6
10F
3
2
1
8
4
R7
4.99k
U1A
OP284
D2
AD589
D1
1N4148
R5
22.1k
Q1
SI9433DY
R4
2.21k
6
5
7
C 1
0.01F
U1B
OP284
D 3
1N4148
2
6
4
3
U2
REF192
C 2
1F
R1
4.53k
V
OUT
2
2.5V
R3
10k
5.0V
4.5V
3.3V
3.0V
4.99k
4.53k
2.43k
1.69k
10.0k
8.06k
3.24k
2.00k
10.0k
10.0k
10.0k
10.0k
V
OUT
R1
R2
R3
OUTPUT TABLE
V
S
>
V
OUT
+ 0.1V
OPTIONAL
ON/OFF CONTROL INPUT
CMOS HI (OR OPEN) = ON
LO = OFF
V
IN
COMMON
V
C
V
OUT
=
4.5V @ 350mA
(SEE TABLE)
V
OUT
COMMON
Figure 55. A Low Dropout Regulator with Current Limiting
REV. 0
16
OP184/OP284/OP484
Obviously, it is desirable to keep this comparison voltage small,
since it becomes a significant portion of the overall dropout
voltage. Here, the 20 mV reference is higher than the typical
offset of the OP284 but still reasonably low as a percentage of
V
OUT
(< 0.5%). In adapting the limiter for other I
LIMIT
levels,
sense resistor R
S
should be adjusted along with R7-R8, to main-
tain this threshold voltage between 20 mV and 50 mV.
Performance of the circuit is excellent. For the 4.5 V output
version, the measured dc output change for a 225 mA load
change was on the order of a few microvolts while the dropout
voltage at this same current level was about 30 mV. The current
limit as shown is 400 mA, which allows the circuit to be used at
levels up to 300 mA or more. While the Q1 device can actually
support currents of several amperes, a practical current rating
takes into account the SO-8 device's 2.5 W, 25
C dissipation.
Because a short circuit current of 400 mA at an input level of 5
V will cause a 2 W dissipation in Q1, other input conditions
should be considered carefully in terms of Q1's potential over-
heating. Of course, if higher powered devices are used for Q1,
this circuit can support outputs of tens of amperes as well as the
higher V
OUT
levels noted above.
The circuit shown can be used either as a standard low dropout
regulator, or it can be used with ON/OFF control. By
driving Pin 3 of U1 with the optional logic control signal V
C
, the
output is switched between ON and OFF. Note that when the
output is OFF in this circuit, it is still active (i.e., not an open cir-
cuit). This is because the OFF state simply reduces the voltage
input to R1, leaving the U1A/B amplifiers and Q1 still active.
When ON/OFF control is used, resistor R10 should be used
with U1 to speed ON-OFF switching and to allow the output of
the circuit to settle to a nominal zero voltage. Components D3
and R11 also aid in speeding up the ON-OFF transition by pro-
viding a dynamic discharge path for C2. OFF-ON transition
time is less than 1 ms, while the ON-OFF transition is longer
but under 10 ms.
A +3 V, 50 Hz/60 Hz Active Notch Filter with False Ground
To process signals in a single-supply system, it is often best
to use a false ground biasing scheme. A circuit that uses this
approach is illustrated in Figure 56. In this circuit, a false-ground
circuit biases an active notch filter used to reject 50 Hz/60 Hz
power line interference in portable patient monitoring equip-
ment. Notch filters are quite commonly used to reject power
line frequency interference that often obscures low frequency
physiological signals, such as heart rates, blood pressure read-
ings, EEGs, EKGs, etc. This notch filter effectively squelches
60 Hz pickup at a filter Q of 0.75. Substituting 3.16 k
resis-
tors for the 2.67 k
in the twin-T section (R1 through R5)
configures the active filter to reject 50 Hz interference.
1
3
5
6
7
11
2
+3V
R1
2.67k
C1
1F
C 2
1F
R3
2.67k
C3
2F
(1F x 2)
R4
2.67k
R5
1.33k
(2.67k
2)
R2
2.67k
V
O
R6
10k
V
IN
R8
1k
A2
A1
8
A3
R7
1k
R11
10k
4
10
9
C5
0.03F
R12
150
R10
20k
C4
1F
R9
20k
+3V
1.5V
C6
1F
A1, A2, A3 = OP484
Q = 0.75
NOTE: FOR 50Hz APPLICATIONS
CHANGE R1R4 TO 3.1k
AND R5 TO 1.58k
(3.16k
2).
Figure 56. A +3 V Single Supply, 50/60 Hz Active Notch
Filter with False Ground
Amplifier A3 is the heart of the false-ground bias circuit. It
simply buffers the voltage developed at R9 and R10 and is the
reference for the active notch filter. Since the OP484 exhibits a
rail-to-rail input common-mode range, R9 and R10 are chosen
to split the +3 V supply symmetrically. An in-the-loop compen-
sation scheme is used around the OP484 that allows the op amp
to drive C6, a 1
F capacitor, without oscillation. C6 maintains
a low impedance ac ground over the operating frequency range
of the filter.
The filter section uses a OP484 in a twin-T configuration whose
frequency selectivity is very sensitive to the relative matching of
the capacitors and resistors in the twin-T section. Mylar is the
material of choice for the capacitors, and the relative matching
of the capacitors and resistors determines the filter's pass band
symmetry. Using 1% resistors and 5% capacitors produces
satisfactory results.
REV. 0
17
OP184/OP284/OP484
*OP284 SPICE Macro-model 9/94 / Rev. A
*
ARG/ADI
*
* Copyright 1995 by Analog Devices
*
* Refer to "README.DOC" file for License Statement. Use of
this model
* indicates your acceptance of the terms and provisions in the
License
* Statement.
*
* Node assignments
*
noninverting input
*
| inverting input
*
| | positive supply
*
| | | negative supply
*
| | | | output
*
| | | | |
.SUBCKT OP284
1 2 99 50 45
*
* INPUT STAGE
*
Q1
5
2
3
QIN 1
Q2
6
11
3
QIN 1
Q3
7
2
4
QIP 1
Q4
8
11
4
QIP 1
DC1
2
11
DC
DC2
11
2
DC
Q5
4
9
99
QIP 1
Q6
9
9
99
QIP 1
Q7
3
10
50
QIN 1
Q8
10
10
50
QIN 1
R1
99
5
4E3
R2
99
6
4E3
R3
7
50
4E3
R4
8
50
4E3
IREF
9
10
50.5E-6
EOS
1
11
POLY(2) (22,98) (14,98) -25E-6 1E-2 1
IOS
2
1
5E-9
CIN
1
2
2E-12
GN1
98
1
(17,98) 1E-3
GN2
98
2
(23,98) 1E-3
*
* VOLTAGE NOISE SOURCE WITH FLICKER NOISE
*
VN1
13
98
DC 2
VN2
98
15
DC 2
DN1
13
14
DEN
DN2
14
15
DEN
*
* CURRENT NOISE SOURCE WITH FLICKER NOISE
*
VN3
16
98
DC 2
VN4
98
18
DC 2
DN3
16
17
DIN
DN4
17
18
DIN
*
* 2ND CURRENT NOISE SOURCE WITH FLICKER
NOISE
*
VN5
19
98
DC 2
VN6
98
24
DC 2
DN5
19
23
DIN
DN6
23
24
DIN
*
* GAIN STAGE
*
EREF
98
0
POLY(2) (99,0) (50,0) 0 0.5 0.5
G1
98
20
POLY(2) (6,5) (8,7) 0 0.5E-3 0.5E-3
R9
20
98
1E3
*
* COMMON MODE STAGE WITH ZERO AT 100Hz
*
ECM
98
21
POLY(2) (1,98) (2,98) 0 0.5 0.5
R10
21
22
1
R11
22
98
100E-6
C4
21
22
1.592E-3
*
* NEGATIVE ZERO AT 20MHz
*
E1
27
98
(20,98) 1E6
R17
27
28
1
R18
28
98
1E-6
C8
25
26
7.958E-9
ENZ
25
98
(27,28) 1
VNZ
26
98
DC 0
FNZ
27
28
VNZ -1
*
* POLE AT 40MHz
*
G4
98
29
(28,98) 1
R19
29
98
1
C9
29
98
3.979E-9
*
* POLE AT 40MHz
*
G5
98
30
(29,98) 1
R20
30
98
1
C10
30
98
3.979E-9
*
* OUTPUT STAGE
*
ISY
99
50
0.276E-3
GIN
50
31
POLY(1) (30,98) .862574E-6 505.879E-6
RIN
31
50
2.75E6
VB
99
32
0.7
Q11
32
31
33
QON 1
R21
33
34
4.5E3
I1
34
50
50E-6
R22
99
35
6E3
Q12
36
36
35
QOP 1
I2
36
50
50E-6
R23
99
37
2.6E3
R24
34
38
5E3
Q13
39
36
37
QOP 1
Q14
39
38
40
QON 1.5
R25
40
50
40
Q15
39
39
41
QON 1
R26
41
42
1E3
R27
99
43
220
Q16
44
44
43
QOP 1.5
Q17
44
39
42
QON 1
R28
42
50
2E3
VSCP
99
97
DC 0
REV. 0
18
OP184/OP284/OP484
FSCP
46
99
VSCP 1
RSCP
46
99
40
Q20
44
46
99
QOP 1
Q18
45
44
97
QOP 4.5
Q19
45
34
51
QON 4.5
VSCN
51
50
DC 0
FSCN
50
47
VSCN 1
RSCN
47
50
40
Q21
34
47
50
QON 1
CC2
31
45
20E-12
CF1
31
34
15E-12
CF2
31
42
15E-12
CO1
34
45
15E-12
CO2
42
45
5E-12
D3
45
99
DX
D4
50
45
DX
.MODEL DC D(IS=130E-21)
.MODEL DX D()
.MODEL DEN D(RS=100 KF=12E-15 AF=1)
.MODEL DIN D(RS=5.358 KF=56E-15 AF=1)
.MODEL QIN NPN(BF=200 VA=200 IS=0.5E-16)
.MODEL QIP PNP(BF=100 VA=60 IS=0.5E-16)
.MODEL QON NPN(BF=200 VA=200 IS=0.5E-16 RC=50)
.MODEL QOP PNP(BF=200 VA=200 IS=0.5E-16 RC=160)
.ENDS
REV. 0
19
OP184/OP284/OP484
14-Lead Epoxy DIP
(P Suffix)
14
1
7
8
0.795 (20.19)
0.725 (18.42)
0.280 (7.11)
0.240 (6.10)
PIN 1
SEATING
PLANE
0.022 (0.558)
0.014 (0.356)
0.060 (1.52)
0.015 (0.38)
0.210 (5.33)
MAX
0.130
(3.30)
MIN
0.070 (1.77)
0.045 (1.15)
0.100
(2.54)
BSC
0.160 (4.06)
0.115 (2.93)
0.325 (8.25)
0.300 (7.62)
0.015 (0.381)
0.008 (0.204)
0.195 (4.95)
0.115 (2.93)
14-Lead Narrow-Body SO
(S Suffix)
14
8
7
1
0.3444 (8.75)
0.3367 (8.55)
PIN 1
0.1574 (4.00)
0.1497 (3.80)
0.2440 (6.20)
0.2284 (5.80)
SEATING
PLANE
0.0098 (0.25)
0.0040 (0.10)
0.0192 (0.49)
0.0138 (0.35)
0.0688 (1.75)
0.0532 (1.35)
0.0500
(1.27)
BSC
0.0098 (0.25)
0.0075 (0.19)
0.0500 (1.27)
0.0160 (0.41)
8
0
0.0196 (0.50)
0.0099 (0.25)
x 45
8-Lead Epoxy DIP
(P Suffix)
8
1
4
5
0.430 (10.92)
0.348 (8.84)
0.280 (7.11)
0.240 (6.10)
PIN 1
SEATING
PLANE
0.022 (0.558)
0.014 (0.356)
0.060 (1.52)
0.015 (0.38)
0.210 (5.33)
MAX
0.130
(3.30)
MIN
0.070 (1.77)
0.045 (1.15)
0.100
(2.54)
BSC
0.160 (4.06)
0.115 (2.93)
0.325 (8.25)
0.300 (7.62)
0.015 (0.381)
0.008 (0.204)
0.195 (4.95)
0.115 (2.93)
8-Lead SO
(S Suffix)
8
5
4
1
0.1968 (5.00)
0.1890 (4.80)
PIN 1
0.1574 (4.00)
0.1497 (3.80)
0.2440 (6.20)
0.2284 (5.80)
SEATING
PLANE
0.0098 (0.25)
0.0040 (0.10)
0.0192 (0.49)
0.0138 (0.35)
0.0688 (1.75)
0.0532 (1.35)
0.0500
(1.27)
BSC
0.0098 (0.25)
0.0075 (0.19)
0.0500 (1.27)
0.0160 (0.41)
8
0
0.0196 (0.50)
0.0099 (0.25)
x 45
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
PRINTED IN U.S.A.
C21671210/96
20
PDF 
ZIP