Input Specifications:
Voltage range
12VDC, 9~18VDC
24VDC, 18~36VDC
48VDC, 36~72VDC
Filter
p
(Pi) Network
TO ORDER CALL 1-888-9-AIMTEC
AM6T-N Series
6 watt dc-dc converters
24 PIN DIP PACKAGE
WIDE 2:1 INPUT RANGE
HIGH EFFICIENCY UP TO 86%
SHIELDED METAL PACKAGE
INPUT/OUTPUT ISOLATION OF 1500VDC
OPERATING TEMPERATURE: -40C ... +71C
CONTINUOUS SHORT CIRCUIT PROTECTION
PIN-COMPATIBLE WITH MULTIPLE MANUFACTURERS
GENERAL DESCRIPTION
ELECTRICAL SPECIFICATIONS
All specifications valid at nominal input voltage, full load and +25C after warm-up time unless otherwise stated.
Our AM6T-N series is a family of cost effective 6W
single and dual output DC/DC converters. These
converters combine a shielded metal package in a
24-pin DIP compatible case and includes high per-
formance features such as a 1500VDC input/output
isolation voltage, continuous short circuit protection
and a tight line / load regulation. Wide range devices
operate over a 2:1 input voltage range continuously
providing a stable output voltage.
27 models operate from input voltages of 12, 24 and
48VDC with output voltages of 3.3, 5, 12, 15, 24, 5,
12, 15 & 24VDC. High performance features
include high efficiency operation up to 86% and output
voltage accuracy of 1%. All models are packaged in a
low profile 31.75 x 20.32 x 10.16mm case. Operation
is specified over the full operating temperature range of
-40C to +71C with no derating required. Cooling is
by free-air convection.
MTBF: > 1,000,000 hrs (MIL-HDBK-217F, Ground Benign, t=+25C)
Specifications are subject to change without notification.
Isolation Specifications:
Rated voltage (60 sec)
1500VDC
Resistance >
1000MOhm
Capacitance 120pF,
typ.
Output Specifications:
Voltage accuracy (Single)
1%, typ.
Voltage accuracy (Dual)
1% p. & 3% n., typ.
Ripple 30m
Vp-p,
typ.
Noise
(at 20MHz BW)
100mVp-p, typ.
Short circuit protection
Continuous
Line voltage regulation
0.2%, max.
Load voltage regulation
0.5%, max.
Temperature coefficient
0.02%/C, typ.
Environmental Specifications:
Operating temperature
(ambient)
-40C ... +71C
Storage temperature
-55C ... +125C
Case Temperature
+100C, max.
Derating
None required
Humidity (non-condensing)
Up to 95%
Cooling
Free-air Convection
Physical Specifications:
Dimensions
31.75x20.32x10.16mm
1.25x0.80x0.40inches
Weight 19g
Case material
Metal
General Specifications:
Efficiency
76% to 86%
Switching frequency
300KHz, typ., 100% load
DC-DC CONVERTERS
Continued on next page
TO ORDER CALL 1-888-9-AIMTEC
AM6T-N Series
DC-DC CONVERTERS
APPLICATION NOTE
Recommended Circuit
All of our AM6T-N Series have been tested according to the following
recommended testing circuit before leaving our factory. This series should be
tested under load & never be tested under no load (See Figure 1).
If you want to further decrease the input/output ripple, you can increase
capacitance properly or choose capacitors with a low ESR. However, the
capacitance should not be too high.(See table 1).
Input Current
When it is used in an unregulated power supply, be sure that the fluctuating
range of the power supply and the rippled voltage do not exceed the module
standard. Input current of power supply should afford the startup current of
this kind of DC/DC module. (See figure 2)
External Capacitor
Although this series of DC/DC converters can work without an external
capacitor, it is highly recommended to use one in order to keep an optimum
performance. (See Table 1)
Requirement on Output Load
To ensure this module operate efficiently and reliably, a minimum load is
specified for this kind of DC/DC converter in addition to a maximum load
(namely full load). During operation, make sure the specified range of input
voltage is not exceeded, the minimum out put load is not less than 10% Of
the full load, and that this product should never be operated under no load!!!
If the actual load is less below the specified minimum load, the output ripple
of this type of DC/DC converter will increase drastically and at the same time
efficiency & reliability of the circuit will decrease deeply .If the actual output
power from the load in your circuit is very small, please connect a resistor
with proper resistance at the output end in parallel to increase the load, or
use our company's other products with a lower rated output power.
TYPICAL CHARACTERISTICS
Pin
Single
Dual
2
-V Input
-V Input
3
-V Input
-V Input
9
Omitted
Common
11
N.C.
-V Output.
14
+V Output
+V Output
16
-V Output
Common
22
+V Input
+V Input
23
+V Input
+V Input
OUTLINE DIMENSIONS & PIN CONNECTIONS
Note: All Pins on a 2.54mm pitch; All Pin diameters are 0.50 mm (Tolerance:0.25);
All dimensions in mm.
External Capacitor Table
Single & Dual Outputs
Figure 1 - Single Output
Figure 1 - Dual Output
Figure 2 - Single & Dual Outputs
Vin
Cin
Vout
Cout
12V
100uF
5V
100uF each
1A Current
24V
100uF
12V
48V
100uF
15V
-
-
24V
PDF 
ZIP