5713
DUAL PERIPHERAL AND POWER DRIVER
DISCONTINUED PRODUCT
-- FOR REFERENCE ONL
Y
This "mini-DlP" dual peripheral and power driver is a bipolar
monolithic integrated circuit incorporating NOR logic gates, high-
current switching transistors, and transient suppression diodes on the
same chip. The two output transistors are capable of simultaneously
sinking 300 mA continuously at ambient temperatures of up to +70
C.
In the OFF state, this driver will withstand at least 80 V.
The UDN5713M dual driver is ideally suited for interface between
low-level or high-level logic and high-current/high-voltage loads.
Typical applications include driving peripheral loads such as incandes-
cent lamps, light-emitting diodes, memories, and heaters with a load
current of up to 600 mA.
The integral transient suppression diodes allow the use of these
drivers with inductive loads such as relays, solenoids, or stepping
motors without the need for discrete diodes. Similar devices with four
drivers per package are the 5703 and 5706.
FEATURES
s
DTL/TTL/PMOS/CMOS Compatible Inputs
s
Low Input Current
s
300 mA Continuous Output Current
s
Stand-off Voltage of 80 V
Dwg. No. A-9789
DUAL PERIPHERAL AND POWER DRIVER
-- TRANSIENT PROTECTED OUTPUTS
5713
Always order by complete part number, e.g.,
UDN5713M .
ABSOLUTE MAXIMUM RATINGS
Supply Voltage, V
CC
. . . . . . . . . . . . . .
7.0 V
Input Voltage, V
IN
. . . . . . . . . . . . . . . . .
30 V
Output Off-State Voltage,
V
OFF
. . . . . . . . . . . . . . . . . . . . . . . . 80 V
Output On-State Sink Current,
I
ON
. . . . . . . . . . . . . . . . . . . . . . 600 mA
Suppression Diode Off-State Voltage,
V
OFF
. . . . . . . . . . . . . . . . . . . . . . . . 80 V
Suppression Diode On-State Current,
I
ON
. . . . . . . . . . . . . . . . . . . . . . 600 mA
Power Dissipation at T
A
= 25
C, P
D
Package . . . . . . . . . . . . . . . . . . . 1.5 W*
Each Driver . . . . . . . . . . . . . . . . . 0.8 W
Operating Free-Air Temperature Range,
T
A
. . . . . . . . . . . . . . . . . -20
C to +85
C
Storage Temperature Range,
T
S
. . . . . . . . . . . . . . . . -55
C to +150
C
*Derate at the rate of 12.5 mW/
C above
T
A
= 25
C.
Data Sheet
29307B
5713
DUAL PERIPHERAL AND POWER DRIVER
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Min.
Nom.
Max.
Units
Supply Voltage (V
CC
)
4.75
5.0
5.25
V
Operating Temperature Range
0
+25
+85
C
Current into any output (ON state)
--
--
300
mA
RECOMMENDED OPERATING CONDITIONS
ELECTRICAL CHARACTERISTICS over operating temperature range
(unless otherwise noted).
Test Conditions
Limits
Driven
Other
Characteristic
Symbol
Temp.
V
CC
Input
Input
Output
Min.
Typ.
Max.
Units
Notes
"1" Input Voltage
V
IN(1)
--
MIN
--
--
--
2.0
--
--
V
--
"0" Input Voltage
V
IN(0)
--
MIN
--
--
--
--
--
0.8
V
--
"0" Input Current at all
Inputs except Strobe
I
IN(0)
--
MAX
0.4 V
30 V
--
--
-50
-100
A
2
"0" Input Current at Strobe
I
IN(0)
--
MAX
0.4 V
30 V
--
--
-100
-200
A
--
"1" Input Current at all
Inputs except Strobe
I
IN(1)
--
MAX
30 V
0 V
--
--
--
10
A
2
"1" Input Current at Strobe
I
IN(1)
--
MAX
30 V
0 V
--
--
--
20
A
--
Input Clamp Voltage
V
IK
--
MIN
-12 mA
--
--
--
--
-1.5
V
--
Limits
Characteristic
Symbol
Test Conditions
Min.
Typ.
Max.
Units
Notes
Turn-on Delay Time
t
pd0
V
S
= 70 V, R
L
= 465
(10 Watts),
--
200
500
ns
3
C
L
= 15 pF
Turn-off Delay Time
t
pd1
V
S
= 70 V, R
L
= 465
(10 Watts),
--
300
750
ns
3
C
L
= 15 pF
SWITCHING CHARACTERISTICS at V
CC
= 5.0 V, T
A
= 25
C
NOTES: 1. Typical values are at V
CC
= 5.0 V, T
A
= 25
C.
2. Each input tested separately.
3. Voltage values shown in the test circuit waveforms are with respect to network ground terminal.
4. Capacitance values specified include probe and test fixture capacitance.
INPUT PULSE CHARACTERISTICS
V
IN(0)
=
0 V
t
f
= 7 ns
t
p
= 1
s
V
IN(1)
=
3.5 V
t
r
= 14 ns
PRR = 500 kHz
W
Copyright 1976, 1997, Allegro MicroSystems, Inc.
5713
DUAL PERIPHERAL AND POWER DRIVER
ELECTRICAL CHARACTERISTICS over operating temperature range
(unless otherwise noted).
Test Conditions
Limits
Driven
Other
Characteristic
Symbol
Temp.
V
CC
Input
Input
Output
Min.
Typ.
Max.
Units
Notes
"1" Output Reverse Current
l
OFF
--
MIN
2.0 V
0 V
80 V
--
--
100
A
--
--
OPEN
2.0 V
0 V
80 V
--
--
100
A
--
"0" Output Voltage
V
ON
--
MIN
0.8 V
0.8 V
150 mA
--
0.35
0.5
V
--
--
MIN
0.8 V
0.8 V
300 mA
--
0.5
0.7
V
--
Diode Leakage Current
I
LK
NOM
NOM
0 V
0 V
OPEN
--
--
200
A
3
Diode Forward Voltage Drop
V
D
NOM
NOM
V
CC
V
CC
--
--
1.5
1.75
V
4
"1" Level Supply Current
l
CC(1)
NOM
MAX
5.0 V
5.0 V
--
--
8.0
13
mA
1, 2
"0" Level Supply Current
l
CC(0)
NOM
MAX
0 V
0 V
--
--
36
50
mA
1, 2
NOTES: 1. Typical values are at V
CC
= 5.0 V, T
A
= 25
C.
2. Per package.
3. Diode leakage current measured at V
R
= 80 V.
4. Diode forward voltage drop measured at I
F
= 300 mA.
5. Capacitance values specified include probe and test fixture capacitance.
Dwg. No. A-9123A
Dwg. No. A-7628C
5713
DUAL PERIPHERAL AND POWER DRIVER
115 Northeast Cutoff, Box 15036
Worcester, Massachusetts 01615-0036 (508) 853-5000
Dimensions in Millimeters
(Based on 1" = 25.4 mm)
Dimensions in Inches
0.014
0.008
0.300
BSC
Dwg. MA-001-8A in
0.430
MAX
4
0.100
BSC
5
8
1
0.022
0.014
0.400
0.355
0.005
MIN
0.150
0.115
0.280
0.240
0.210
MAX
0.070
0.045
0.015
MIN
0.355
0.204
7.62
BSC
Dwg. MA-001-8A mm
10.92
MAX
4
10.16
9.02
2.54
BSC
0.13
MIN
3.81
2.93
5
8
1
7.11
6.10
5.33
MAX
1.77
1.15
0.39
MIN
0.558
0.356
NOTES: 1. Lead thickness is measured at seating plane or below.
2. Lead spacing tolerance is non-cumulative.
3. Exact body and lead configuration at vendor's option
within limits shown.
Allegro MicroSystems, Inc. reserves the right to make, from time to time,
such departures from the detail specifications as may be required to permit
improvements in the design of its products.
The information included herein is believed to be accurate and reliable.
However, Allegro MicroSystems, Inc. assumes no responsibility for its use; nor
for any infringements of patents or other rights of third parties which may result
from its use.
PDF 
ZIP