AS1325
300mA Step-Up DC-DC Converter
www.austriamicrosystems.com
Revision 1.00
1 - 16
austria
micro
systems
D a ta S h e e t
1 General Description
The AS1325 is a high-efficiency step-up DC-DC con-
verter designed to generate a fixed output voltage of
+3.3V or +5V.
The AS1325 achieves an efficiency of up to 96% and the
minimum input voltage is 1.5V. The AS1325-BSTT-33
delivers up to 300mA output current at the fixed output
voltage of +3.3V (@ 2V V
BATT
). With the fixed output
voltage of +5V the AS1325-BSST-50 supplies up to
185mA output current (@ 2V V
BATT
).
In order to save power the AS1325 features a shutdown
mode, where it draws less than 1A. In shutdown mode
the battery is connected directly to the output enabling
the supply of real-time-clocks.
The AS1325 provides a power-on reset output that goes
high-impedance when the output reaches 90% of its reg-
ulation point.
The SHDNN trip threshold of the AS1325 can be used
as an input voltage detector that disables the device
when the battery voltage falls to a predetermined level.
An internal synchronous rectifier is included.
The AS1325 is available in a 6-pin SOT23 package.
Figure 1. Application Diagram
2 Key Features
!
Fixed Output Voltage:
- 3.3V (AS1325-BSTT-33) or 5V (AS1325-BSST-50)
!
Output Current:
- Up to 300mA (AS1325-BSTT-33) @ 2V V
BATT
- Up to 185mA (AS1325-BSST-50) @ 2V V
BATT
!
Internal Synchronous Rectifier
!
Shutdown Mode Supply Current: Less Than 1A
!
Efficiency: Up to 96%
!
Minimum Input Voltage: +1.5V
!
Accurate Shutdown Low-Battery Cutoff Threshold
!
Battery Input Connected to Pin OUT in Shutdown
Mode for Backup Power
!
Antiringing Control Minimizes EMI
!
Ripple Reduction at Light Loads
!
6-pin SOT23 Package
3 Applications
The AS1325 is ideal for low-power applications where
ultra-small size is critical as in medical diagnostic equip-
ment, hand-held instruments, pagers, digital cameras,
remote wireless transmitters, cordless phones, and PC
cards. The device is also perfect as a local supply or as
a battery backup.
+5.0V Output only
AS1325
C
OUT
22F
C
IN
22F
L1
10H
RESETN
Output
R
1
100k
On
Off
4
LX
3
GND
2
BATT
6
RESETN
1
SHDNN
5
OUT
+1.5 to +3.3V or
+1.5 to +5.0V
Battery
+3.3 or
+5.0V
Output
www.austriamicrosystems.com
Revision 1.00
2 - 16
AS1325
austria
micro
systems
Data Sheet
4 Absolute Maximum Ratings
Stresses beyond those listed in
Table 1
may cause permanent damage to the device. These are stress ratings only,
and functional operation of the device at these or any other conditions beyond those indicated in
Section 5 Electrical
Characteristics on page 3
is not implied. Exposure to absolute maximum rating conditions for extended periods may
affect device reliability.
Table 1. Absolute Maximum Ratings
Parameter
Min
Max
Units
Comments
All Pins to GND
-0.3
7
V
LX Current
1
A
Latch-Up
-100
100
mA
JEDEC 78
Package Power Dissipation
(T
AMB
= +70C)
500
mW
(
JA
= 9.1mW/C above +70C)
Operating Temperature Range
-40
+85
C
Electrostatic Discharge
-500
+500
V
HBM MIL-Std. 883E 3015.7 methods
Humidity (Non-Condensing)
5
85
%
Storage Temperature Range
-55
125
C
Junction Temperature
150
C
Package Body Temperature
260
C
The reflow peak soldering temperature (body
temperature) specified is in compliance with
IPC/JEDEC J-STD-020C "Moisture/ Reflow
Sensitivity Classification for Non-Hermetic
Solid State Surface Mount Devices".
www.austriamicrosystems.com
Revision 1.00
3 - 16
AS1325
austria
micro
systems
Data Sheet
5 Electrical Characteristics
3.3V Output
T
AMB
= -40 to +85C, V
BATT
= +2V, V
OUT
= +3.3, V
SHDNN
= +1.5V (unless otherwise specified). Typ values @ T
AMB
= +25C.
Table 2. Electrical Characteristics
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Battery Input Range
V
BATT
1.5
3.5
V
Startup Battery Input Voltage
1
1. Guaranteed by design.
V
SU
R
LOAD
= 47
, T
AMB
= +25C
1.22
1.5
V
R
LOAD
= 47
, T
AMB
= -40 to +85C
1.24
Output Voltage
2
2. Voltage which triggers next loading cycle. Ripple and rms value depend on external components.
V
OUT
T
AMB
= +25C
3.267 3.300
3.333
V
T
AMB
= -40 to +85C
3.217
3.373
N-Channel
On-Resistance
R
NCH
I
LX
= 100mA, T
AMB
= +25C
0.3
1.2
I
LX
= 100mA, T
AMB
= -40 to +85C
1.5
P-Channel On-Resistance
R
PCH
I
LX
= 100mA, T
AMB
= +25C
0.4
1.3
I
LX
= 100mA, T
AMB
= -40 to +85C
1.6
Light Load N-Channel Switch
Current Limit
400
mA
Maximum N-Channel Switch
Current Limit
1
I
MAX
T
AMB
= +25C
550
700
850
mA
T
AMB
= -40 to +85C
450
950
N-Channel Maximum
On-Time
t
ON
T
AMB
= +25C
5
7
9
s
T
AMB
= -40 to +85C
4
10
P-Channel Minimum On-Time
2
s
Synchronous Rectifier
Zero-Crossing Current
T
AMB
= +25C
8
30
60
mA
T
AMB
= -40 to +85C
0
65
Quiescent Current into OUT
V
OUT
= +3.5V, T
AMB
= +25C
35
55
A
V
OUT
= +3.5V, T
AMB
= -40 to +85C
60
Shutdown Current into OUT
V
SHDNN
= 0V, T
AMB
= +25C
0.01
1
A
V
SHDNN
= 0V, T
AMB
= -40 to +85C
2
Shutdown Current into BATT
V
SHDNN
= 0V, T
AMB
= +25C
0.01
1
A
V
SHDNN
= 0V, T
AMB
= -40 to +85C
2
SHDNN Logic Low
1
V
BATT
= +1.5 to +3.5V
0.3
V
SHDNN Threshold
Rising Edge, T
AMB
= +25C
1.185 1.228
1.271
V
Rising Edge, T
AMB
= -40 to +85C
1.170
1.286
SHDNN Threshold Hysteresis
0.02
V
RESETN Threshold
Falling Edge, T
AMB
= +25C
2.830 3.000
3.110
V
Falling Edge, T
AMB
= -40 to +85C
2.800
3.140
RESETN Voltage Low
I
RESETN
= 1mA, V
OUT
= +2.5V,
T
AMB
= +25C
0.15
V
I
RESETN
= 1mA, V
OUT
= +2.5V,
T
AMB
= -40 to +85C
0.2
RESETN Leakage Current
V
RESETN
= +5.5V, T
AMB
= +25C
0.1
100
nA
V
RESETN
= +5.5V, T
AMB
= +85C
1
LX Leakage Current
T
AMB
= +25C
0.1
1000
nA
T
AMB
= +85C
10
Maximum Load Current
I
LOAD
V
BATT
= +2V
300
mA
Efficiency
V
BATT
= +3V, I
LOAD
= 100mA
96
%
www.austriamicrosystems.com
Revision 1.00
4 - 16
AS1325
austria
micro
systems
Data Sheet
5.0V Output
T
AMB
= -40 to +85C, V
BATT
= +2V, V
OUT
= +5.0, V
SHDNN
= +1.5V (unless otherwise specified). Typ values @ T
AMB
= +25C.
Table 3. Electrical Characteristics
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
Battery Input Range
V
BATT
1.5
5.0
V
Startup Battery Input Voltage
1
1. Guaranteed by design.
V
SU
R
LOAD
= 100
, T
AMB
= +25C
1.22
1.5
V
R
LOAD
= 100
, T
AMB
= -40 to +85C
1.24
Output Voltage
2
2. Voltage which triggers next loading cycle. Ripple and rms value depend on external components.
V
OUT
T
AMB
= +25C
4.950 5.000
5.050
V
T
AMB
= -40 to +85C
4.875
5.125
N-Channel
On-Resistance
R
NCH
I
LX
= 100mA, T
AMB
= +25C
0.3
1.2
I
LX
= 100mA, T
AMB
= -40 to +85C
1.5
P-Channel On-Resistance
R
PCH
I
LX
= 100mA, T
AMB
= +25C
0.4
1.3
I
LX
= 100mA, T
AMB
= -40 to +85C
1.6
Light Load N-Channel Switch
Current Limit
400
mA
N-Channel Switch Current Limit
1
I
MAX
T
AMB
= +25C
550
700
850
mA
T
AMB
= -40 to +85C
450
950
Switch Maximum
On-Time
t
ON
T
AMB
= +25C
5
7
9
s
T
AMB
= -40 to +85C
4
10
P-Channel Minimum On-Time
1
s
Synchronous Rectifier
Zero-Crossing Current
T
AMB
= +25C
8
30
60
mA
T
AMB
= -40 to +85C
0
65
Quiescent Current into OUT
V
OUT
= +5.5V, T
AMB
= +25C
35
55
A
V
OUT
= +5.5V, T
AMB
= -40 to +85C
60
Shutdown Current into OUT
V
SHDNN
= 0V, T
AMB
= +25C
0.01
1
A
V
SHDNN
= 0V, T
AMB
= -40 to +85C
2
Shutdown Current into BATT
V
SHDNN
= 0V, T
AMB
= +25C
0.01
1
A
V
SHDNN
= 0V, T
AMB
= -40 to +85C
2
SHDNN Logic Low
1
V
BATT
= +1.5 to +5.0V
0.3
V
SHDNN Threshold
Rising Edge, T
AMB
= +25C
1.185 1.228
1.271
V
Rising Edge, T
AMB
= -40 to +85C
1.170
1.286
SHDNN Threshold Hysteresis
0.02
V
RESETN Threshold
Falling Edge, T
AMB
= +25C
4.288 4.500
4.712
V
Falling Edge, T
AMB
= -40 to +85C
4.242
4.758
RESETN Voltage Low
I
RESETN
= 1mA, V
OUT
= +2.5V,
T
AMB
= +25C
0.15
V
I
RESETN
= 1mA, V
OUT
= +2.5V,
T
AMB
= -40 to +85C
0.2
RESETN Leakage Current
V
RESETN
= +5.5V, T
AMB
= +25C
0.1
100
nA
V
RESETN
= +5.5V, T
AMB
= +85C
1
LX Leakage Current
T
AMB
= +25C
0.1
1000
nA
T
AMB
= +85C
10
Maximum Load Current
I
LOAD
V
BATT
= +2V
185
mA
Efficiency
V
BATT
= +3V, I
LOAD
= 100mA
91
%
www.austriamicrosystems.com
Revision 1.00
5 - 16
AS1325
austria
micro
systems
Data Sheet
6 Typical Operating Characteristics
3.3V Characteristics
V
OUT
= 3.3V, V
BATT
= +2V, T
AMB
= +25C.
Figure 2. V
OUT
vs. V
BATT
; On, 16
Figure 3. V
OUT
vs. V
BATT
; On, 330
Figure 4. V
OUT
vs. V
BATT
; Shutdown, 300mA Load
Figure 5. V
OUT
vs. V
BATT
; Shutdown, No Load
Figure 6. Maximum Output Current vs. V
BATT
Figure 7. Startup Voltage vs. Load Resistance
0
1
2
3
4
0
1
2
3
4
Battery Voltage (V)
O
u
t
put
V
o
l
t
ag
e
(
V
)
.
0
1
2
3
4
0
1
2
3
4
Battery Voltage (V)
O
u
t
put
V
o
l
t
ag
e
(
V
)
.
0
1
2
3
4
5
1
2
3
4
5
6
Battery Voltage (V)
O
u
t
put
V
o
l
t
ag
e
(
V
)
.
0
1
2
3
4
5
0
1
2
3
4
5
Battery Voltage (V)
O
u
t
put
V
o
l
t
ag
e
(
V
)
.
0
0.5
1
1.5
2
2.5
3
10
100
1000
10000
Load Resistance (Ohm)
S
uppl
y
V
o
l
t
age
(
V
)
.
200
300
400
500
600
700
800
1
1.5
2
2.5
3
3.5
Battery Voltage (V)
M
a
x
i
m
u
m
O
u
t
put
Cur
r
ent
(
m
A
)
.
www.austriamicrosystems.com
Revision 1.00
6 - 16
AS1325
austria
micro
systems
Data Sheet
Figure 8. Line Transient
Figure 9. Load Transient
Figure 10. On/Off Response; R
LOAD
= 33
Figure 11. Shutdown Response; R
LOAD
= 33
Figure 12. Waveforms; R
LOAD
= 33
Figure 13. Efficiency vs. Load Current
200mA
2mA
500s/Div
V
IN
100s/Div
1V
/D
iv
100mV
/
Div
V
OUT
(A
C Cou
p
led)
I
OUT
100mV
/
Div
V
OUT
(A
C Cou
p
led
)
V
OUT
V
SDHNN
200s/Div
2ms/Div
V
OU
T
V
IN
1V/Div
1V
/D
iv
2V
/Div
1V
/Div
75
80
85
90
95
100
1
10
100
1000
Load Current (mA)
E
f
f
i
ci
e
n
c
y (
%
)
.
10s/Div
V
BATT
= 3V
V
BATT
= 2.5V
V
BATT
= 2V
V
BATT
= 1.5V
V
OUT
(A
C Cou
p
led)
V
LX
I
L
2V
/Div
10
0mV/
Div
500
mA
www.austriamicrosystems.com
Revision 1.00
7 - 16
AS1325
austria
micro
systems
Data Sheet
5.0V Characteristics
V
OUT
= 5.0V, V
BATT
= +2V, T
AMB
= +25C.
Figure 14. V
OUT
vs. V
BATT
; On, 39
Figure 15. V
OUT
vs. V
BATT
; On, 470
Figure 16. V
OUT
vs. V
BATT
; Shutdown, 180mA Load
Figure 17. V
OUT
vs. V
BATT
; Shutdown, No Load
Figure 18. Maximum Output Current vs. V
BATT
Figure 19. Startup Voltage vs. Load Resistance
0
1
2
3
4
5
6
0
1
2
3
4
5
Battery Voltage (V)
O
u
t
put
V
o
l
t
ag
e
(
V
)
.
0
1
2
3
4
5
6
0
1
2
3
4
5
Battery Voltage (V)
O
u
t
put
V
o
l
t
ag
e
(
V
)
.
0
1
2
3
4
5
1
2
3
4
5
Battery Voltage (V)
O
u
t
put
V
o
l
t
ag
e
(
V
)
.
0
1
2
3
4
5
6
0
1
2
3
4
5
6
Battery Voltage (V)
O
u
t
put
V
o
l
t
ag
e
(
V
)
.
0.5
1
1.5
2
2.5
3
3.5
4
10
100
1000
10000
Load Resistance (Ohm)
S
uppl
y
V
o
l
t
age
(
V
)
.
100
200
300
400
500
600
1
1.5
2
2.5
3
3.5
4
4.5
Battery Voltage (V)
M
a
x
i
m
u
m
O
u
t
put
Cur
r
ent
(
m
A
)
.
www.austriamicrosystems.com
Revision 1.00
8 - 16
AS1325
austria
micro
systems
Data Sheet
Figure 20. Line Transient
Figure 21. Load Transient
Figure 22. On/Off Response; R
LOAD
= 100
Figure 23. Shutdown Response; R
LOAD
= 100
Figure 24. Waveforms; R
LOAD
= 68
Figure 25. Efficiency vs. Load Current
130mA
2mA
500s/Div
V
IN
100s/Div
1V
/D
iv
100mV
/
Div
V
OUT
(A
C Cou
p
led
)
I
OUT
100
mV/Di
v
V
OUT
(A
C Cou
p
led
)
V
OUT
V
SDHNN
200s/Div
2ms/Div
V
OU
T
V
IN
1V/Div
2V
/D
iv
2V
/Div
2V
/Div
75
80
85
90
95
100
1
10
100
1000
Load Current (mA)
Ef
f
i
ci
e
n
cy (%
)
.
4s/Div
V
BATT
= 3V
V
BATT
= 2.5V
V
BATT
= 2V
V
BATT
= 1.5V
V
OUT
(A
C Cou
p
led)
V
LX
I
L
5V
/Div
50mV
/
Div
500
mA
V
BATT
= 3.5V
V
BATT
= 4.5V
www.austriamicrosystems.com
Revision 1.00
9 - 16
AS1325
austria
micro
systems
Data Sheet
Control Circuitry
7 Detailed Description
The AS1325 is a high-efficiency, compact step-up converter with 35A quiescent supply current which ensures the
highest efficiency over a wide load range. With a minimum of +1.5V input voltage, the device is well suited for applica-
tions with one- or two-cells, such as lithium ion (Li+), nickel-metal-hydride (NiMH), or alkaline.
Figure 26. Block Diagram
The input battery is connected to the device through an inductor and an internal P-FET when pin SHDNN is low. In this
state, the step-up converter is off and the voltage drop across the P-FET body diode is eliminated, and the input bat-
tery can be used as a battery-backup or real-time-clock supply.
The built-in synchronous rectifier significantly improves efficiency.
Control Circuitry
The AS1325 integrated current-limited key circuitry provides low quiescent current and extremely-high efficiency over
a wide V
OUT
range without the need for an oscillator.
Light Loads:
Inductor current is limited by the 0.4A N-channel current limit or by the 7s switch maximum on-time. The lower current
limit reduces the ripple of the output voltage. At each cycle, the inductor current must ramp down to zero before the
next cycle may start. When the error comparator senses that the output has fallen below the regulation threshold,
another cycle begins.
Higher Loads:
If after the first light load cycle the output voltage has not reached its target value of 3.3V or 5.0V, the inductor current
limit is increased to 0.7A. After the P-channel minimum on-time the next loading cycle is started if the output voltage is
still below its target value. If the target value is reached, the inductor current must ramp down to zero before the next
cycle may start. When the error comparator senses that the output has fallen below the regulation threshold, another
load cycle begins (see
Figure 12 on page 6
and
Figure 24 on page 8
).
+5.0V Output only
V
REF
Zero
Crossing
Detector
AS1325
Driver
and
Control
Logic
Startup
Circuitry
10H
+1.5 to +3.3V or
+1.5 to +5.0V
Battery
Current
Limiter
+1.228V
C
IN
22F
+
+
+1.1V
+3.3 or
+5.0V
Output
C
OUT
22F
4
LX
2
BATT
6
RESETN
1
SHDNN
5
OUT
GND 3
Anti-
Ring-
ing
Switch
www.austriamicrosystems.com
Revision 1.00
10 - 16
AS1325
austria
micro
systems
Data Sheet
Shutdown
Shutdown
When pin SHDNN is low the AS1325 is switched off and no current is drawn from battery; when pin SHDNN is high the
device is switched on. If SHDNN is driven from a logic-level output, the logic high-level (on) should be referenced to
V
OUT
to avoid intermittently switching the device on.
Note: If pin SHDNN is not used, it should be connected directly to pin OUT.
In shutdown the battery input is connected to the output through the inductor and the internal synchronous rectifier P-
FET. This allows the input battery to provide backup power for devices such as an idle microcontroller, memory, or real-
time-clock, without the usual diode forward drop. In this way a separate backup battery is not needed.
In cases where there is residual voltage during shutdown, some small amount of energy will be transferred from pin
OUT to pin BATT immediately after shutdown, resulting in a momentary spike of the voltage at pin BATT. The ratio of
C
IN
and C
OUT
partly determine the size and duration of this spike, as does the current-sink ability of the input device.
Low-Battery Cutoff
The AS1325 SHDNN trip threshold (1.228V) can be used as an input voltage detector that disables the device when
the battery input voltage falls to a pre-set level. An external resistor-divider network can be used to set the battery-
detection voltage
(see Figure 27)
.
Figure 27. Low-Battery Cutoff Application Diagram
For the resistor-divider network shown in
Figure 27
, calculate the value for R
1
by:
R
1
= R
2
x ((V
OFF
/V
SHDNN
) - 1)
(EQ 1)
Where:
V
OFF
is the battery voltage at which the AS1325 shuts down.
V
SHDNN
= 1.228V
The value of R
2
should be between 100k
and 1M
to minimize battery drain.
Note: Input ripple can cause false shutdowns, therefore to minimize the effect of ripple, a low-value capacitor from
SHDNN to GND should be used to filter out input noise. The value of the capacitor should be such that the R/C
time constant is > 2ms.
+1.5 to +3.3V or
+1.5 to +5.0V
Battery
+3.3V or +5.0V
Output
C
OUT
22F
C
IN
22F
L1
10H
Power-On
Reset
R
3
100k
10nF
R
1
220k
R
2
1M
AS1325
4
LX
3
GND
2
BATT
6
RESETN
1
SHDNN
5
OUT
+5.0V Output only
www.austriamicrosystems.com
Revision 1.00
11 - 16
AS1325
austria
micro
systems
Data Sheet
Power-On Reset
The AS1325 provides a power-on reset output (RESETN) that goes high-impedance when the output reaches 90% of
its regulation point. RESETN goes low when the output is below 90% of the regulation point. A 100k
to 1M
pullup
resistor between pin RESETN and pin OUT can provide a microprocessor logic control signal.
Note: Connect pin RESETN to GND when the power-on reset feature is not used.
Antiringing Control
If the inductor current falls to zero, an internal 100
(typ) antiringing switch is connected from LX to BATT to minimize
EMI. The antiringing control can be deactivated by not connecting the pin BATT. The device is supplied by the pin OUT
- no supply current flows into pin BATT.
www.austriamicrosystems.com
Revision 1.00
12 - 16
AS1325
austria
micro
systems
Data Sheet
8 Application Information
Inductor Selection
The control circuitry of the AS1325 permits a wide range of inductor values to be selected from 4.7 to 22H; The sys-
tem is optimized for 10H.
The intended application should dictate the value of L. The trade-off between required PCB surface area and desired
output ripple are the determining factors: smaller values for L require less PCB space, larger values of L reduce output
ripple. If the value of L is large enough to prevent I
MAX
from being reached before t
ON
expires, the AS1325 output
power will be reduced.
Note: Coils should be able to handle 500mA
RMS
and have a I
SAT
1A and should have a R
IND
100m
.
Capacitor Selection
Low ESR capacitors (X5R or X7R) should be used to minimize the output voltage ripple.
C
OUT
Selection
Choose a C
OUT
value to achieve the desired output ripple. A 22F ceramic capacitor is a good initial value. A larger
value for C
OUT
can be used to further reduce ripple and improve AS1325 efficiency.
C
IN
Selection
C
IN
reduces the peak current drawn from the battery and can be the same value as C
OUT
.
External Diode (5V Output only)
An external Schottky diode must be connected, in parallel with the on-chip synchronous rectifier, from LX to OUT. Use
diodes such as MBR0520L, EP05Q03L, or the generic 1N5817. The diode should be rated for 500mA, since it carries
current during startup and after the synchronous rectifier turns off. The Schottky diode must be connected as close to
the IC as possible. Ordinary rectifier diodes must not be used, since the slow recovery rate will compromise efficiency.
PC Board Layout and Grounding
Well-designed printed circuit-board layout is important for minimizing ground bounce and noise.
!
Place pin GND lead and the ground leads of C
IN
and C
OUT
as close to the device as possible.
!
Keep the lead to pin LX as short as possible.
!
To maximize output power and efficiency and minimize output ripple voltage, use a ground plane and solder the
GND pin directly to the ground plane.
www.austriamicrosystems.com
Revision 1.00
13 - 16
AS1325
austria
micro
systems
Data Sheet
Pin Assignments
9 Pinout and Packaging
Pin Assignments
Figure 28. Pin Assignments (Top View)
Pin Descriptions
Table 4. Pin Descriptions
Name
Pin Number
Description
SHDNN
1
Active-Low Logic Shutdown Input
0 = The AS1325 is off and the supply current is
1A (typ).
1 = The AS1325 is on.
BATT
2
Battery Voltage Input
GND
3
Ground
LX
4
External Inductor Connection
OUT
5
Output Voltage
RESETN
6
Active-Low reset output
AS1325
1
BATT 2
3
6
5
4
GND
SHDNN
OUT
LX
RESETN
www.austriamicrosystems.com
Revision 1.00
14 - 16
AS1325
austria
micro
systems
Data Sheet
Package Drawings and Markings
Package Drawings and Markings
The AS1325 is available in a 6-pin SOT23 package.
Figure 29. 6-pin SOT23 Package
Symbol
Min
Max
A
0.90
1.45
A1
0.00
0.15
A2
0.90
1.30
b
0.35
0.50
C
0.08
0.20
D
2.80
3.00
E
2.60
3.00
E1
1.50
1.75
L
0.35
0.55
e
0.95 REF
0
10
Notes:
1. All dimensions are in millimeters.
2. Foot length is measured at the intercept point between datum
A and lead surface.
3. Package outline exclusive of mold flash and metal burr.
4. Pin 1 is the lower left pin when reading the top mark from left
to right.
5. Pin 1 identifier dot is 0.3mm.
min and is located above pin 1.
6. Meets JEDEC MO178.
www.austriamicrosystems.com
Revision 1.00
15 - 16
AS1325
austria
micro
systems
Data Sheet
Package Drawings and Markings
10 Ordering Information
The AS1325 is available as the standard products shown in
Table 5
.
Table 5. Ordering Information
Part
Marking
Description
Delivery Form
Package
AS1325-BSTT-33
ASKY
300mA Step-Up DC-DC Converter
Tape and Reel
6-pin SOT23
AS1325-BSTT-50
ASK6
185mA Step-Up DC-DC Converter
Tape and Reel
6-pin SOT23
www.austriamicrosystems.com
Revision 1.00
16 - 16
AS1325
austria
micro
systems
Data Sheet
Package Drawings and Markings
Copyrights
Copyright 1997-2006, austriamicrosystems AG, Schloss Premstaetten, 8141 Unterpremstaetten, Austria-Europe.
Trademarks Registered . All rights reserved. The material herein may not be reproduced, adapted, merged, trans-
lated, stored, or used without the prior written consent of the copyright owner.
All products and companies mentioned are trademarks or registered trademarks of their respective companies.
Disclaimer
Devices sold by austriamicrosystems AG are covered by the warranty and patent indemnification provisions appearing
in its Term of Sale. austriamicrosystems AG makes no warranty, express, statutory, implied, or by description regarding
the information set forth herein or regarding the freedom of the described devices from patent infringement. austriami-
crosystems AG reserves the right to change specifications and prices at any time and without notice. Therefore, prior
to designing this product into a system, it is necessary to check with austriamicrosystems AG for current information.
This product is intended for use in normal commercial applications. Applications requiring extended temperature
range, unusual environmental requirements, or high reliability applications, such as military, medical life-support or life-
sustaining equipment are specifically not recommended without additional processing by austriamicrosystems AG for
each application. For shipments of less than 100 parts the manufacturing flow might show deviations from the standard
production flow, such as test flow or test location.
The information furnished here by austriamicrosystems AG is believed to be correct and accurate. However,
austriamicrosystems AG shall not be liable to recipient or any third party for any damages, including but not limited to
personal injury, property damage, loss of profits, loss of use, interruption of business or indirect, special, incidental or
consequential damages, of any kind, in connection with or arising out of the furnishing, performance or use of the tech-
nical data herein. No obligation or liability to recipient or any third party shall arise or flow out of
austriamicrosystems AG rendering of technical or other services.
Contact Information
Headquarters
austriamicrosystems AG
A-8141 Schloss Premstaetten, Austria
Tel: +43 (0) 3136 500 0
Fax: +43 (0) 3136 525 01
For Sales Offices, Distributors and Representatives, please visit:
http://www.austriamicrosystems.com
austria
micro
systems
a leap ahead
PDF 
ZIP