AAT3132
High Efficiency 1.5X Fractional Charge
Pump for White LED Applications
3132.2004.04.1.0
1
ChargePump
TM
General Description
The AAT3132 is a low noise, constant frequency
charge pump DC/DC converter that uses fractional
(1.5X) conversion to maximize efficiency for White
LED applications. The device can be used to pro-
duce current levels up to 20mA in three of its out-
puts, and up to 25 or 30mA in one of its outputs to
drive LEDs from a 2.7V to 5.5V input. Outputs may
be operated individually or paralleled for driving
higher-current LEDs. Low external parts count (two
1F flying capacitors and two small 1F capacitors
at V
IN
, and OUT) make the AAT3132 ideally suited
for small battery-powered applications.
AnalogicTechTM's Simple Serial ControlTM
(S
2
CwireTM) interface is used to enable, disable
and set the LED drive current in two groups: the
three 20mA outputs and the single 30mA output
with multiple level logarithmic scales. The AAT3132
has a thermal management system to protect the
device in the event of a short circuit condition at the
output pin. Built-in soft-start circuitry prevents
excessive inrush current during start-up. A high
charge pump switching frequency enables the use
of very small external capacitors. A low current
shutdown feature disconnects the load from V
IN
and reduces quiescent current to less than 1A.
The AAT3132 is available in very small 12 pin
TSOPJW12 package.
Features
V
IN
Range: 2.7 - 5.5 Volts
< 1.0A of Shutdown current
1.0 MHz Switching Frequency
White LED Backlighting
Fully Independent Display Lighting
Drives Low-V
F
& High-V
F
Type LEDs
Up to three 20mA Outputs
Single 25 or 30mA Output
Multi Position Logarithmic Scale with Digital
Control
Low Noise Constant Frequency Operation
Regulated Output Current
Automatic Soft-Start
No Inductors
-40 to +85C Temperature Range
12 pin TSOPJW-12 package
Applications
White LED Backlighting
White Photo-Flash for DSC's
Color (RGB) Lighting
Programmable Current Source
Typical Application
C
IN
1
F
V
BATTERY
C
OUT
1
F
EN/SET
C1
1
F
C2
1
F
D5
D3
D2
D1
V
IN
V
OUT
C1+
C1-
C2+
C2-
D1
D2
D3
D4
EN/SET
GND
AAT3132
D4
Pin Descriptions
Pin Configuration
TSOPJW-12
(Top view)
1
2
3
4
5
6
12
11
10
9
8
7
C2+
OUT
C1-
C1+
D3
D2
C2-
GND
IN
EN/SET
D1
D4
Pin #
Symbol
Function
1
C2+
Flying Capacitor 2 + terminal. Connect a 1F capacitor between C2+ and C2-.
2
OUT
Charge pump output. Requires 1F capacitor connected between this pin and
ground.
3
C1-
Flying Capacitor 1 - terminal
4
C1+
Flying Capacitor 1 + terminal. Connect a 1F capacitor between C1+ and C1-.
5
D3
Current source output #3
6
D2
Current source output #2
7
D4
Current source output #4
8
D1
Current source output #1
9
EN/SET
Control Pin
10
IN
Input power supply. Requires 1F capacitor connected between this pin and
ground.
11
GND
Ground
12
C2-
Flying Capacitor 2 - terminal
AAT3132
High Efficiency 1.5X Fractional Charge
Pump for White LED Applications
2
3132.2004.04.1.0
Absolute Maximum Ratings
1
Notes:
1. Stresses above those listed in Absolute Maximum Ratings may cause permanent damage to the device. Functional operation at condi-
tions other than the operating conditions specified is not implied. Only one Absolute Maximum rating should be applied at any one time.
2. Based on long-term current density limitation.
Thermal Information
Note 3: Mounted on a FR4 board.
Note 4: Derate 6.25mW/C above 25C.
Symbol
Description
Value
Units
JA
Thermal Resistance
3
160
C/W
P
D
Maximum Power Dissipation (T
A
= 25C)
3, 4
625
mW
Symbol
Description
Value
Units
V
IN
Input Voltage
-0.3 to 6
V
V
OUT
Charge Pump Output
-0.3 to 6
V
F
B
, V
EN/SET
FB or EN/SET to GND Voltage
-0.3 to 6
V
V
EN/SET(MAX)
Maximum EN/SET to Input Voltage
V
IN
- 0.3
V
I
OUT
(2)
Maximum DC Output Current
150
mA
T
J
Operating Junction Temperature Range
-40 to 150
C
AAT3132
High Efficiency 1.5X Fractional Charge
Pump for White LED Applications
3132.2004.04.1.0
3
Electrical Characteristics
1
V
IN
= 3.5V, C
IN
= C
OUT
= C1 = C2 = 1.0F; T
A
= -40 to 85C unless otherwise noted. Typical values are T
A
= 25C.
Notes:
1. The AAT3132 is guaranteed to meet performance specification over the -40 to 85C operating temperature range and are assured by
design, characterization and correlation with statistical process controls.
Symbol
Description
Conditions
Min
Typ
Max
Units
Input Power Supply
V
IN
Operation Range
2.7
5.5
V
I
CC
Operating Current
3.0
V
IN
5.5, Active,
1.8
3.5
mA
No Load Current
I
SHDN
Shutdown Current
EN = 0
1.0
A
I
DX
Max. Output Current D1 to D3
3.0
V
IN
5.5
18
20
22
mA
I
DX
Max. Output Current D4
T
A
= 25C AAT3132-1
22.5
25
27.5
mA
T
A
= 25C AAT3132
27
30
33
I
(D-Match)
Current Matching between
VD1:D3 = 3.6, V
IN
= 3.3V
0.5
%
any two outputs
CP
Charge Pump Section Efficiency
V
IN
= 3.5V, I
OUT(TOTAL)
= 90mA,
93
%
Measured from IN to OUT
Charge Pump Section
T
SS
Soft start time
200
s
F
CLK
Clock Frequency
1000
kHz
EN/SET
V
EN(L)
Enable Threshold Low
0.5
V
V
EN(H)
Enable Threshold High
1.4
V
T
EN/SET LO
EN/SET low time
V
EN/SET
< 0.5
0.3
75
s
T
EN/SET HI
Minimum EN/SET high time
V
EN/SET
> 1.4
50
ns
T
OFF
EN/SET Off Timeout
V
EN/SET
< 0.5
500
s
Input Current EN/SET input leakage
-1
1
A
AAT3132
High Efficiency 1.5X Fractional Charge
Pump for White LED Applications
4
3132.2004.04.1.0
AAT3132
High Efficiency 1.5X Fractional Charge
Pump for White LED Applications
3132.2004.04.1.0
5
Typical Characteristics
(Unless otherwise noted, V
IN
= 3.5V, C
IN
= C
OUT
= C1 = C2 = 1F, T
A
= 25C)
80mA Load Characteristics
1
s/div
20mV/div
V
IN
OUT
V
DIODE
Turn-Off
200
s/div
ENSET
(1V/div)
V
DIODE
(2V/div)
I
IN
(100mA/div)
Turn-On to Full Scale Load-Switch
50
s/div
ENSET
(1V/div)
OUT
(2V/div)
V
DIODE
(2V/div)
I
IN
(100mA/div)
Turn-On to Full Scale Charge-Pump
50
s/div
ENSET
(1V/div)
OUT
(2V/div)
V
DIODE
(1V/div)
I
IN
(200mA/div)
V
IH
and V
IL
vs. V
IN
0.600
0.625
0.650
0.675
0.700
0.725
0.750
0.775
0.800
0.825
0.850
2.5
3.0
3.5
4.0
4.5
5.0
5.5
V
IN
(V)
V
IH
V
IL
I
DIODE
vs. V
IN
(4x20mA)
40
45
50
55
60
65
70
75
80
85
90
2.7 2.9
3.1 3.3
3.5
3.7
3.9
4.1 4.3
4.5
4.7 4.9
5.1
V
IN
(V)
I
DIODE
(mA)
V
DIODE
= 3.3V
V
DIODE
= 3.4V V
DIODE
= 3.5V
V
DIODE
= 3.6V
PDF 
ZIP