DC/DC CONVERTERS 6A Non-isolated DC/DC Converters
1
2 YEAR WARRANTY
SIL06 Series
S i n g l e o u t p u t
Ultra wide trim range 0.9V to 3.3V/5.0V
Current sink capability for termination application
Horizontal and vertical-mount options available
High power density design means reduced board space
requirement
Power good output signal (open collector)
Operating ambient temperature up to +80C with suitable
derating and forced air cooling
Remote ON/OFF (active high)
0A minimum load
Input under-voltage lockout
Over-current and short-circuit protection
The SIL06 Series is a new high density open frame non-isolated converter for space
sensitive applications. Each model has a wide input range (4.5 - 5.5VDC or 10.2 -
13.8VDC) and offer a wide 0.9 - 5V output voltage range with a 6A load. An external
resistor adjusts the output voltage from its pre-set value of 0.9V to any value up to the
5V maximum. Typical efficiencies for the models are 89% for the 5V input version and
91% for the 12V input version. The SIL06 series offers remote ON/OFF and over-
current protection as standard. With full international safety approval including
EN60950 and UL/cUL60950, the SIL06 reduces compliance costs and time to market.
NEW Product
All specifications are typical at nominal input, full load at 25C unless otherwise stated
SPECIFICATIONS
OUTPUT SPECIFICATIONS
Voltage adjustability
5V input models
0.9V to 3.3V
(See Note 7)
12V input models
0.9V to 5.0V
Output setpoint accuracy With 1.0% trim resistors
2.5%
Line regulation
Low line to high line
0.2% max.
Load regulation
Full load to min. load
0.5% max.
Min./max. load
0A/6A
Overshoot
5V input models
3.0% max.
(at turn on)
12V input models
1.0% max.
Undershoot
100mV max.
Ripple and noise
5Hz to 20MHz (See Note 2)
See table
Transient response
Deviation
75mV
(See Note 1)
150s recovery to
within regulation band
INPUT SPECIFICATIONS
Input voltage range
5V input model
4.5 to 5.5VDC
12V input model
10.2 to 13.8VDC
Input current
No load
50mA
Remote OFF
5mA
Input current (max.)
5V input model
5.1A @ Io max.
(See Note 9)
12V input model
1.6A @ Io max.
Input reflected ripple
5V input model
52mA (pk-pk)
(See Note 2)
12V input model
56mA (pk-pk)
Remote ON/OFF
Logic compatibility
Active high
ON
>2.4VDC
OFF
<0.8VDC
Start-up time
Power up
<20ms
(See Note 3)
Remote ON/OFF
<20ms
File Name: SIL06.PDF Rev: 10 Dec 2002
INPUT SPECIFICATIONS Contd.
Turn ON threshold
5Vin model
4.5V
12Vin model
9.0V
Turn OFF threshold
5Vin model
4.3V
12Vin model
7.5V
GENERAL SPECIFICATIONS
Efficiency
See table
Switching frequency
Fixed
200kHz
Approvals and
TV Product Service
standards (See Note 4)
IEC60950, UL/cUL60950
Material flammability
UL94V-0
Weight
9.3g (0.3oz)
MTBF
MIL-HDBK-217F
1,307,257 hours
Representative model:
12V model @ 40C
100% load, ground benign
Bellcore 332
7, 562,142 hours
ENVIRONMENTAL SPECIFICATIONS
Thermal performance
Operating ambient,
0C to +80C
(See Note 10)
temperature
Non-operating
-40C to +125C
Altitude derating
3,000m (9,843 ft)
20%
(above sea level)
10,000m (32,808 ft)
50%
Notes
1
di/dt = 10A/s, Vin = Nom, Tc = 25C, load change = 0.5 lo max. to 0.75
lo max. and 0.75 lo max. to 0.5 lo max.
2
Measured with external filter. See Application Note 131 for details.
3
Power up is the time from application of DC input to Power Good
enabled. Remote ON/OFF is from ON/OFF asserted high to Power Good
enabled
4
This product is only for inclusion by professional installers within other
equipment and must not be operated as a stand alone product.
5
The standard unit with the suffix '-V' is for vertical mounting. To order a
unit with horizontal mounting, please add the suffix '-H' to the model
number, e.g. SIL06-05SADJ-H.
6
Measured as per recommended set-up. Cin = 270F (20m esr max.).
Cout = 680F (10m esr max.).
7
Uses external resistor from trim to output ground. Minimum value 485
for 5V model, 280 for 12V model. See Applications Note 131 for
details.
8
Signal line assumed <3m.
9
External input fusing recommended.
10
See Application Note 131 for operation above 50C.
11
See Application Note 131 for more details.
12
These models have a wide trim output. 5Vin has an output of 0.9V to
3.3V and 12 Vin has an output of 0.9V to 5V. An external resistor adjusts
the output voltage.
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
International Safety Standard Approvals (pending)
TV
CAUTION: High internal temperatures. Ensure that unit is not user
accessible.
SIL06 Series
S i n g l e O u t p u t
DC/DC CONVERTERS 6A Non-isolated DC/DC Converters
2
NEW Product
OUTPUT
INPUT
OVP
OUTPUT
OUTPUT
OUTPUT
EFFICIENCY
REGULATION
MODEL
POWER
VOLTAGE
VOLTAGE
(12)
CURRENT
CURRENT
(TYP.)
LINE
LOAD
NUMBER
(5)
(MAX.)
(MIN.)
(MAX.)
20W
4.5-5.5VDC
N/A
0.9V - 3.3V
0A
6A
89%
0.2%
0.5%
SIL06-05SADJ-V
30W
10.2-13.8VDC
N/A
0.9V - 5.0V
0A
6A
91%
0.2%
0.5%
SIL06-12SADJ-V
Ripple and Noise Specification
PIN CONNECTIONS
PIN NUMBER
FUNCTION
1
Vout
2
Trim
3
Ground
4
Power Good
5
Remote ON/OFF
6
Vin
7
Mechanical support
8
Mechanical support
9
Mechanical support on
horizontal version only
Please consult our website for the following items:
Application Note
Longform Data Sheet
www.artesyn.com
Output
Model
Voltage
Pk - Pk
RMS
5V input models
0.9 to 2.5V
30mV
15mV
3.3V
40mV
15mV
12V input models
0.9 to 2.5V
40mV
20mV
3.3 to 5V
50mV
20mV
PROTECTION
Short-circuit protection
Hiccup, non-latching
RECOMMENDED SYSTEM CAPACITANCE
Input capacitance (See Note 11)
270F/20m esr max.
Output capacitance (See Note 11)
680f/10m esr max.
File Name: SIL06.PDF Rev: 10 Dec 2002
For the most current data and application support visit www.artesyn.com/powergroup/products.htm
SIL06 Series
S i n g l e O u t p u t
DC/DC CONVERTERS 6A Non-isolated DC/DC Converters
3
NEW Product
All dimensions in INCHES (mm)
General tolerance
0.01in (0.25mm)
except where specified otherwise
1.200
(30.48)
0.610
(15.49)
0.527
(13.38)
0.025
(0.64) Typ.
Mechanical
Support Pin
0.062
(1.57)
PCB Ref.
PIN 8
0.025
(0.64) Typ.
PIN 1
0.315
(8.00 max.)
0.150
(3.81) Ref.
0.120
(3.05)
9 Places
Figure 1: Mechanical Drawing - Horizontal Mount Version
Figure 2: Mechanical Drawing - Vertical Mount Version
All dimensions in inches (mm)
General tolerance
0.01in (0.25mm)
except where specified otherwise
0.070
(1.78)
0.315
(8.00) max.
Pin 1
Pin 8
0.025
(0.64)
0.610
(15.49)
1.200
(30.48)
0.040
(1.02) Ref.
0.150
(3.81)
8 Places
0.062
(1.57) Ref.
0.050
(1.27)
0.025
(0.64) Typ.
Data Sheet Artesyn Technologies 2002
The information and specifications contained in this data sheet are believed to be correct at time of publication. However, Artesyn Technologies accepts no responsibility for consequences arising
from printing errors or inaccuracies. Specifications are subject to change without notice. No rights under any patent accompany the sale of any such product(s) or information contained herein.
Please consult our website for the following items:
Application Note
Longform Data Sheet
www.artesyn.com
File Name: SIL06.PDF Rev: 10 Dec 2002
PDF 
ZIP