SL120 only
OUTPUT SPECIFICATIONS
Output voltage
5V Models
4.5V to 5.5V
adjustability
24V Models
18V to 26V
Line regulation
LL to HL, FL
0.2%
Load regulation
60% FL, 40%
SL120
2.0%
SL220
1.0%
Overshoot/undershoot
At turn-on
None
Transient response
SL120: +5V (12A to 20A)
300mV,
1ms recovery
SL220: +5V (10A to 20A)
100mV,
1ms recovery
Temperature coefficient SL120, all outputs
0.03%/C
SL220, all outputs
0.05%/C
Overvoltage protection
5V output
6.25 0.75V
Output power limit
SL120
130W min.
SL220
260W min.
Short circuit protection
Yes
INPUT SPECIFICATIONS
Input voltage range
User Selectable
85 to 132VAC
170 to 264VAC
Input frequency range
47Hz to 440Hz
Maximum input
SL120: 230VAC, cold start
22A
surge current
SL220: 230VAC, cold start
74A
Safety ground
230VAC Input, 50Hz
0.7mA
leakage current
GENERAL SPECIFICATIONS
Hold-up Time
Low line, full load
SL120, 110VAC
36ms
SL120, 230VAC
36ms
SL220, 110VAC
20ms
SL220, 230VAC
20ms
Efficiency
65%, max.
Isolation voltage
SL220 Input/Output
1500VAC
SL220 Input/Chassis
1500VAC
SL120 Input/Output
3750VAC
SL120 Input/Chassis
1500VAC
Approvals and
Safety: SL120 series
VDE0805,
standards
EN60950, UL478
CSA bulletin No. 1402C
Weight
SL120
1.2kg (42.4oz)
SL220
2.3kg (81.2oz)
MTBF
SL120
25,000 hours min.
SL220
50,000 hours min.
ENVIRONMENTAL SPECIFICATIONS
Thermal performance
Operating, See Note 8
0C to +70C
Non-operating
40C to +85C
Relative humidity
Non-condensing
5% to 80% RH
Altitude
Operating
10,000 feet max.
Non-operating
30,000 feet max.
SL120: For new design-ins see the NFS110 Series instead
SL220: For new design-ins see the NFS200 and LX200 Series instead
SL120 and SL220 SERIES
Single output
[ 2 YEAR WARRANTY ]
115/230 VAC input
UL, CSA and (VDE approved - SL120 only)
Short circuit protection
Floating output
20ms hold-up time min.
This series of 100 Watt to 220 Watt single output switchers use an advanced
circuit topology providing superior performance at low cost. Smaller and lighter
than equivalent linear supplies, they are available in 5V and 24V output versions.
The floating outputs can be referenced as either positive or negative. The SL120
model is UL, CSA and VDE approved. Also, selected models incorporate remote
sense. SL120/220 Series power supplies are suitable for a wide variety of
applications, including front end power systems, general industrial and telecom
equipment.
SPECIFICATION
All specifications are typical at nominal input, full load at 25C unless otherwise stated
PAGE 1
OUTPUT
OUTPUT
(1)
OUTPUT
(2)
REGULATION
(3)
NOISE
MODEL NUMBER
POWER
VOLTAGE
ADJ. RANGE
LINE
(4)
LOAD
(5)
PK-PK
100W
5V@20A
4.5 to 5.5V
0.2%
2.0%
1.0%
SL120-4605
220W
5V@44A
4.5 to 5.5V
0.2%
1.0%
1.0%
SL220-4605
(6)
220W
24V@9A
18 to 26V
0.2%
1.0%
1.0%
SL220-4624
(6)
Notes
1
Peak current in excess of the maximum indicated rating may be available
on some outputs. However, this will effect output regulation. Consult
factory for details.
2
Other output voltage versions available. Consult factory for details.
3
20% of rated output loading is required to ensure operation within
specified regulation limits.
4
Measured from low line to high line at full load.
5
Measured at 60% full load, 40%.
6
The SL220-4605 offers an auxiliary 24V output, rated at 2A on pin 7. The
SL220-4624 offers an auxiliary 48V output, rated at 1A on pin 7.
7
Output sense will compensate for up to 3VDC load line drop. The output
current limit increases with output voltage. Care must be taken not to
exceed the maximum output power capability of the power supply.
8
Derate linearly from rated power at 50C to half rated power at 70C.
9
This product is only for inclusion by professional installers within other
equipment and must not be operated as a stand alone product.
Mechanical notes
A
Dashed line indicates minimum clearance.
B
Connect JP1 to either E1 (110V) or E2 (220V) as required.
3.22
(81.79)
ALL DIMENSIONS IN INCHES (mm)
11.50
(292.1)
2.20
(55.88)
0.250
(6.35)
SL120
OUTPUT VOLTAGE
ADJUSTMENT
6-32 SCREW TYP
11.50
(292.10)
1.50
(38.10)
PIN 1
110V
6-32 THREADED
INSERTS 4 PLACES
- 2 MAX. DP.
3.50
(88.9)
0.67
(17.02)
SL220
BEAU. INC.
72-5-09C
E2 (230V)
PIN 1
KULKA ELECT.
4597A-6-32-02
PIN 1
E1 (110V)
6-32 SCREW
TYP
4.15
(105.41
4.65
(118.11)
11.00
(279.4)
F1 5A
250V
0.156 (3.96)
DIA. 4
PLACES
14.50
0.02
(368.30
0.06)
14.00
(355.6)
0.250
(6.35)
0.187
(4.75) DIA.
4 PLACES
1.60
(40.64)
0.87
(22.10)
2.72
(69.09)
A
230V
P1
P2
JP1
P2
P1
B
4.87
(123.70)
A
International Safety Standard Approvals: SL120-4605 only
VDE0805/EN60950 File No. 10401-3336-1006, Licence No. 4345
UL478 Reg. File No. E131987
CSA Bulletin No. 1402C, File No. LR41062C
PIN CONNECTIONS
P1
SL220
Pin 1
AC Live
Pin 2
AC Ground
Pin 3
AC Neutral
P2
Pin 1
DC Output
Pin 2
DC Output
Pin 3
DC Output
Pin 4
Return
Pin 5
Return
Pin 6
Return
Pin 7
Auxiliary Output
(6)
Pin 8
N/C
Pin 9
N/C
Pin 10
+Remote Sense
(7)
Pin 11
Remote Sense
(7)
PIN CONNECTIONS
P1
SL120
Term 1
AC Ground
Term 2
AC Neutral
Term 3
AC Live
P2
Term 1
DC Output
Term 2
DC Output
Term 3
DC Output
Term 4
Return
Term 5
Return
Term 6
Return
Term 7
N/C
Term 8
+Remote Sense
(7)
Term 9
Remote Sense
(7)
100 to 220 Watt
AC/DC user-selectable input switch mode power supplies
AC/DC POWER SUPPLIES
|
100-220W AC
PAGE 2
http://www.artesyn.com
PDF 
ZIP