AGM9624A
Page 2 of
8
AZ DISPLAYS, INC.
General Specification
Driving IC S6B0724A
Interace With Paraller MPU 8080 Series!
Display Specification
Display Dot Matrix :96*24
Display Mode:Positive/Transflective/FSTN Type
Viewing Angle :6:00 Clock
Display Duty:1/33
Driving Bias:1/6 Driving Voltage:7.5V
Mechanical Characteristics(Unit:mm)
Extenal Dimension:27.09*17.76*1.7
View Area:24.09*8.26
Dots Size:0.19*0.0.195
Dots Pitch:0.22*0.22
AGM9624A
Page 4 of
8
AZ DISPLAYS, INC.
Absolute Maximum Ratings
Item
Symbol
Standard
Unit
Power supply voltage
V
DD
-V
SS
0
-
5.5
Input voltage
VIN
VSS
-
VDD
V
Operating temperature range
T
A
-20
-
+70
Storage temperature range
T
STO
-30
-
+80
"
*Wide temperature range is available
Interface Pin Description
Pin No
Symbol
I/O
Function
26
CS1B
I
This is the
chip select signal .When CS1B=
# L" and CS2=
# H",then the chip select becomes active,and data/command I/O
is enabled
25
RESETB
I
When
RESETB
is
set
to
" L" ,the setting are initialized
The
RESETB operation is performed by the RESETB signal
level
24
RS
I
Select register.
0:Instruction register (for write) Busy flag &address counter(for
read)
1:Data register(for write and read).
23
RW-WRB
I
Read/write select signal.
22
E-RDB
I
Operation (data read/write) enable signal.
21
DB0
20
DB1
19
DB2
18
DB3
17
DB4
16
DB5
15
DB6
14
DB7
I/O
This is an 8-bit bi-directional data bus that connects to an 8-bit
or 16-bit standard MPU data bus.
When the serial interface is selected,then D7 serves as the serial
data input terminal and D6 serves as the serial clock input
terminal.At this time,D0-D5 are set to high impedence.
When the chip select is inactive,D0 to D7 are set to high
impedance.
13
VDD
Supply
Power supply for logic
12
VSS
Supply
Ground.
11
VOUT
O
DC/DC voltage converter output
10
C3+
O
Capacitor3+ for internal DC/DC voltage converter
9
C1-
O
Capacitor1- for internal DC/DC voltage converter
8
C1+
O
Capacitor1+ for internal DC/DC voltage converter
7
C2+
O
Capacitor2+ for internal DC/DC voltage converter
6
C2-
O
Capacitor2- for internal DC/DC voltage converter
AGM9624A
Page 5 of
8
AZ DISPLAYS, INC.
5
V1
4
V2
3
V3
2
V4
1
V0
Supply
LCD driver supply voltages.The voltage determined by LCD
cell is impedangce-converted by a resistive driver or an
operation amplifier for application .Voltages should be the
following relationship:
V0>V1>V2>V3>V4>VSS
When the on-chip operating power circuit is on,the following
are given to V1 to V4 by the on-chip power circuit .Voltage
selection is performed by the set LCD bias command.
LCD
BIAS
V1
V2
V3
V4
1/5BIAS
4/5V0
3/5V0
2/5V0
1/5V0
1/6 BIAS
5/6V0
4/6 V0
2/6 V0
1/6 V0
1/7 BIAS
6/7 V0
5/7 V0
2/7 V0
1/7 V0
1/8 BIAS
7/8 V0
6/8 V0
2/8 V0
1/8 V0
1/9 BIAS
8/9 V0
7/9 V0
2/9 V0
1/9 V0
PDF 
ZIP
