Specifications are subject to change without notice (17.07.06)
1
Monitoring Relays
Product Description
Ordering Key
Housing
Function
Type
Item number
Output
Power supply
3-phase monitoring relays for phase
sequence and phase loss
Detect when all 3 phases are present and have the
correct sequence
Measure on own power supply
Power supply range: 208 to 690 VAC (+10 -15%)
Output: 8 A SPDT relay or 8 A DPDT normally energized
For mounting on DIN-rail in accordance with DIN/EN
50 022 (DPA01) or plug-in module (PPA01)
22.5 mm Euronorm housing (DPA01) or 36 mm plug-in
module (PPA01)
LED indication for relay and power supply ON
Type Selection
Mounting
Output
208 to 480 VAC
208 to 240 VAC
380 to 480 VAC
380 to 600 VAC
600 to 690 VAC
DIN-rail
SPDT
DPA 01 C M44
DPA 01 C M60
DPA 01 C M69
DIN-rail
DPDT
DPA 01 D M23
DPA 01 D M48
Mounting
Output
208 to 415 VAC
208 to 240 VAC
380 to 415 VAC
Plug-in
SPDT
PPA 01 C M44
Plug-in
DPDT
PPA 01 D M23
PPA 01 D M48
Input
L1, L2, L3
DPA01: Terminals L1, L2, L3
PPA01: Terminals 5, 6, 7
Measures on own supply
Measuring ranges
208 to 480 VAC (DPA01CM44) 177 to 550 VAC
380 to 600 VAC (DPA01CM60) 323 to 690 VAC
600 to 690 VAC (DPA01CM69) 510 to 760 VAC
208 to 415 VAC (PPA01CM44) 177 to 475 VAC
208 to 240 VAC (DPA01DM23) 177 to 275 VAC
380 to 480 VAC (DPA01DM48) 323 to 550 VAC
208 to 240 VAC (PPA01DM23) 177 to 275 VAC
380 to 415 VAC (PPA01DM48) 323 to 475 VAC
ON-level
> 85% of the mains phase-
phase voltage
3-Phase Sequence and Phase Loss
Types DPA01, PPA01
Input Specifications
Output
SPDT or DPDT relay, N.E.
Rated insulation voltage
250 VAC
Contact ratings (AgSnO
2
)
DPA01C, PPA01C (SPDT):
Resistive loads
AC 1
8 A @ 250 VAC
DC 12
5 A @ 24 VDC
Small inductive loads AC 15
2.5 A @ 250 VAC
DC 13
2.5 A @ 24 VDC
DPA01D, PPA01D (DPDT):
Resistive loads
AC 1
8 A @ 250 VAC
Small inductive loads AC 15
3 A @ 250 VAC
DC 13
2 A @ 24 VDC
Mechanical life
30 x 10
6
operations
Electrical life
10
5
operations
(at 8 A, 250 V, cos
= 1)
Operating frequency
7200 operations/h
Dielectric strength
Dielectric voltage
2 kVAC (rms)
Rated impulse withstand volt. 4 kV (1.2/50 s)
Output Specifications
DPA 01 C M44
3-phase relay for detection of
incorrect phase sequence,
total and partial phase loss.
Supply range from 208 to 690
VAC covered by two multi-
voltage relays.
For mounting on DIN-rail or
plug-in module. The device
detects regenerated voltages
up to 85% of the nominal
voltage (phase-phase).
DPA01
PPA01
2
Specifications are subject to change without notice (17.07.06)
DPA01, PPA01
Mode of Operation
DPA01 and PPA01 monitor
their own 3-phase power
supply. The relay operates
when all the phases are pre-
sent and the phase
sequence is correct. The
relay releases when one
phase-phase voltage drops
below 85% of the other
phase-phase voltages.
Example 1
The relay monitors that the
power supply has the correct
phase sequence and that all
phase voltages are present.
Example 2
The relay releases in case of
interruption of one or more
phases, provided that the
regenerated voltage does
not exceed 85% of the
phase-phase voltage.
Power supply
Overvoltage cat. III
Rated operational voltage
(IEC 60664, IEC 60038)
through terminals:
(DPA01)
L1, L2, L3
(PPA01)
5, 6, 7
DPA01CM44
208 to 480 VAC 15%,
45 to 65 Hz
DPA01CM60
380 to 600 VAC15%,
45 to 65 Hz
PPA01CM44
208 to 415 VAC 15%,
45 to 65 Hz
DPA01CM69
600 to 690 VAC +10 -15%,
45 to 65 Hz
DPA01DM23
208 to 240 VAC 15%,
45 to 65 Hz
DPA01DM48
380 to 480 VAC 15%,
45 to 65 Hz
PPA01DM23
208 to 240 VAC 15%,
45 to 65 Hz
PPA01DM48
380 to 415 VAC 15%,
45 to 65 Hz
Rated operational power
M23
6 VA @ 230 VAC, 50 Hz
M44, M48
10 VA @ 400 VAC, 50 Hz
M60
15VA @ 600 VAC, 50Hz
M69
15VA @ 690 VAC, 50Hz
Supplied by L2 and L3
Supply Specifications
Reaction time
Alarm ON delay
< 100 ms
Alarm OFF delay
< 350 ms
Accuracy
(15 min warm-up time)
Temperature drift
1000 ppm/C
Repeatability
0.5% on full scale
Indication for
Power supply ON
LED, green
Relay ON
LED, yellow
Environment
(EN 60529)
Degree of protection
IP 20
Pollution degree
3 (DPA01), 2 (PPA01)
Operating temperature
@ Max. voltage, 50 Hz
-20 to +60C, R.H. < 95%
@ Max. voltage, 60 Hz
-20 to +50C, R.H. < 95%
Storage temperature
-30 to +80C, R.H. < 95%
Housing
Dimensions
DPA01
22.5 x 80 x 99.5 mm
PPA01
36 x 80 x 94 mm
Weight
Approx. 100 g
Screw terminals
(DPA01)
Tightening torque
Max. 0.5 Nm
acc. to IEC 60947
Approval
UL - CSA (except PPA01D,
DPA01CM69)
CE Marking
Yes
EMC
Electromagnetic Compatibility
Immunity
According to EN 61000-6-2
Emissions
According to EN 61000-6-3
General Specifications
Operation Diagram
L1
L2
L3
L2
L1
L3
L3
L2
L1
L1
L2
L3
L2
L1
L1
Relay(s) ON
L3
PDF 
ZIP