THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
1
2
Cx057
00
7/22/03
www.conwin.com
The Connor-Winfield
ABOV5S3E is a 5V Voltage
Controlled Oven Controlled
Crystal Oscillator (VCOCXO)
with an HCMOS output. The
ABOV5S3E is designed for
Stratum 3E applications
requiring low jitter and tight
frequency stability.
ABOV5S3E - 10.00MHz
OCXO
SERIES
CENTER
FREQUENCY
FEATURES
DESCRIPTION
ORDERING INFORMATION
DESIGNED TO MEET STRATUM 3E
REQUIREMENTS
VARIABLE FREQUENCY (VCOCXO)
FREQUENCY STABILITY 10ppb
5.0V OPERATION
HCMOS OUTPUT
STRATUM 3E HCMOS VCOCXO
ABOV5S3E
ABSOLUTE MAXIMUM RATINGS
TABLE 1.0
PARAMETER
UNITS
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Storage Temperature
-40
-
85
C
Supply Voltage
(Vcc)
-0.5
-
7
Vdc
OPERATING SPECIFICATIONS
TABLE 2.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Center Frequency
(Fo)
10
12.8
MHz
1
Frequency Calibration (Vc= 2.5 Vdc)
-0.2
0.2
ppm
2
Frequency Stability
-10
-
10
ppb
3
Aging: Daily
-1
-
1
ppb/day
4
Aging: First Year
-30
-
30
ppb
Aging: Short Term (1Sec.)
-
5.00E-11
-
RMS
5
Aging: Long Term (20 Years)
-
-
300
ppb
Operating Temperature Range
0
-
70
C
Supply Voltage
(Vcc)
4.75
5.00
5.25
Vdc
Voltage Stability (+/-1%)
-0.5
-
0.5
ppb
6
Load Stability (+/-20%)
-0.5
-
0.5
ppb
7
Power Consumption: Turn On
-
-
2.75
W
8
Power Consumption: Steady-State
-
-
1.50
W
8
Start-Up Time
500
mS
9
Warm Up
-100
-
100
ppb
10
2G Tip-over
-
5
-
ppb/G
TDEV at 300 seconds
-
-
5
nS
11
TDEV at 40 seconds
-
-
1
nS
11
INPUT CHARACTERISTICS
TABLE 3.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Control Voltage (Pin 1)
Vc
0.5
2.5
4.5
Vdc
Deviation @ 25C referenced to Fo
0.3
-
1.0
ppm
9
Input Impedance (Pin 1)
50K
-
-
Ohm
HCMOS OUTPUT CHARACTERISTICS
TABLE 4.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
LOAD
12
15
18
pF
12
Voltage (High)
(Voh)
Vcc-0.2V
-
-
Vdc
(Low)
(Vol)
-
-
0.2
Vdc
Duty Cycle at 50% of Vcc
45
50
55
%
Rise / Fall Time 10% to 90%
-
-
5
nS
Spurious Output
-80
dBc
SSB Phase Noise at 1Hz offset
-
-
-90
dBc/Hz
SSB Phase Noise at 10Hz offset
-
-
-115
dBc/Hz
SSB Phase Noise at 100Hz offset
-
-
-130
dBc/Hz
SSB Phase Noise at 1KHz offset
-
-
-135
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-
-140
dBc/Hz
RESTABILIZATION TIME
TABLE 5 .0
Off Time
Restabilization Time
NOTE
< 1 Hour
< 2 Hours
13
< 6 Hours
< 12 Hours
13
< 24 Hours
< 48 Hours
13
1 to 16 Days
48 Hours + Off Time
13
> 16 Days
< 6 Days
13
CONNOR
WINFIELD
MODEL ABOV5S3E
FREQUENCY
DATE CODE
CAL. FREQ.
10.000MHz
0021
10.000000
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
2
2
Cx057
00
7/22/03
www.conwin.com
MODEL ABOV5S3E
FREQUENCY 10.000MHz
DATE CODE 0021
CAL. FREQ. 10.000000
.500
12.700mm
Notes:
1) Labels will include the calibration frequency at the time of ship.
2) Initial calibration @ 25
C, Vc=2.5Vdc.
3) Frequency vs. temperature stability.
4) After ten days of continuous operation.
5) Allen Variance: 1 second, 100 average.
6) Frequency vs. change in supply voltage.
7) Frequency vs. change in load.
8) Vcc = 5.0Vdc.
9) From Vcc=90% of final value. No more than 16 transitions at start -up before oscillator has
started.
10) Measured @ 0
C, within 5 minutes, referenced one hour after turn-on.
11) At time of delivery.
12) HCMOS load.
13) For a given off time, the time required to meet daily aging, short-term stability and TDEV
requirements.
CONTROL VOLTAGE
REF.
SUPPLY
+4.5Vdc
PACKAGE CHARACTERISTICS
TABLE 6.0
Package
Metal package: solder sealed, grounded case,
solder tinned pins.
ENVIRONMNETAL CHARACTERISTICS
TABLE 7.0
Shock
100G's, 6mS, halfsine per MIL-STD-202F,
Method 213B, Test Condition C
Vibration
0.06" D.A. or 10G peak 10 to 500 Hz, per MIL-
STD-202F, Method 204D, Test condition A
PDF 
ZIP