THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
WWW.CONWIN.COM
P R O D U C T D A T A S H E E T
CRYSTAL CONTROLLED OSCILLATORS
14 PIN DIP 3.3V LVMOS STRATUM 3 OCVCXO
CW 0643
AGOV3S3G
12.8M
The Connor-Winfield
AGOV3S3G is a hermetically
sealed 14 Pin DIP 3.3V Oven
Controlled Voltage controlled
Crystal Oscillator (OCVCXO)
with an LVMOS output. The
AGOV3S3G is designed for
Stratum 3 applications requiring
low jitter and tight frequency
AGOV3S3G - 12.800MHz
OCXO
SERIES
CENTER
FREQUENCY
FEATURES
DESCRIPTION
ORDERING INFORMATION
AGOV3S3G
1
2
Cx106
00
10/23/06
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
Notes:
1) Initial calibration @ 25C, Vc=1.48 Vdc.
2) Frequency vs. temperature stability
3) At the time of shipment after48 hours of opera tion.
4) Inclusive of calibration, operating temperature range, supply voltage change, load change, shock
and vibration, 20 years aging, Vc=1.48 Vdc.
5) Measured @ 25C, within 5 minutes, the unit will be within +/-0.1ppm of its reference frequency,
measured after 30 minutes of continuous operation at a stable 25C
6) Referenced to Fo @ 25C, positive transfer characteristic.
3.3V OPERATION
VOLTAGE CONTROLLED FREQUENCY
ADJUST
LOW JITTER <1pS RMS
FREQUENCY STABILITY 0.25ppm
OVERALL FREQUENCY TOLERANCE:
4.6ppm OVER TWENTY YEARS
TEMPERATURE RANGE: 0 to 70C
HERMETICALLY SEALED 14 PIN
PACKAGE
RoHS COMPLIANT / LEAD FREE
ABSOLU TE MAXI MUM RAT INGS
TABLE 1.0
PARAMETER
UNITS
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Storage Temperature
-40
-
85
C
Supply Voltage
(Vcc)
-0.5
-
4.5
Vdc
Control Voltage
(Vc)
-0.5
-
4.5
Vdc
OPERATING SPECIFICATIO NS
TABLE 2.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Center Frequency
(Fo)
1.544
-
20.0
MHz
Frequency Calibration, Vc=1.48 Vdc
-1.5
1.5
ppm
1
Frequency Stability
-0.25
-
0.25
ppm
2
Aging (Daily)
-30
-
30
ppb
3
Aging (20 Years)
-2.5
-
2.5
ppm
Total Frequency Tolerance
-4.6
-
4.6
ppm
4
Operating Temperature Range
0
-
70
C
Supply Voltage
(Vcc)
3.135
3.3
3.465
Vdc
Supply Current
(Icc)
-
-
450
mA
Phase Jitter (BW=12KHz to 20MHz)
-
-
1
ps rms
Phase Jitter (BW=10Hz to 20MHz)
-
-
3
ps rms
Period Jitter
-
-
5
ps rms
SSB Phase Noise at 10Hz offset
-
-90
-
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-135
-
dBc/Hz
Start Up Time: Oscillator
-
-
35
mS
Warm Up Time
-
-
5
Minutes
5
TDEV @ 1.0 Sec.
-
-
1
nS
TDEV @ 4.0 Sec.
-
-
2
nS
INPUT CHARACTERISTICS
TABLE 3.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
Control Voltage Range
(Vc)
0.3
1.48
3.0
Vdc
Frequency at Vc=0.3 Vdc
-22.5
-
-13.5
ppm
6
Frequency at Vc=3.0 Vdc
13.5
-
22.5
ppm
6
Slope of Frequency Adjust
5
-
-
ppm/V
Input Impedance
100k
-
-
Ohm
LVMOS OUTPUT CHARACT ERISTICS
TABLE 4.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
LOAD
-
-
15
pf
Voltage (High)
(Voh)
2.6
-
-
Vdc
(Low)
(Vol)
-
-
0.4
Vdc
Current (High)
(Ioh)
-4
-
mA
(Low)
(Ioh)
-
-
4
mA
Duty Cycle at 50% of Vcc
45
50
55
%
Rise / Fall Time 10% to 90%
-
-
6
nS
PACKAG E CHARACTERISTICS
TABLE 5.0
Package
14 pin DIP, hermetically sealed, grounded case, welded package
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
HTTP://WWW.CONWIN.COM
P R O D U C T D A T A S H E E T
CRYSTAL CONTROLLED OSCILLATORS
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
2
2
Cx106
00
10/23/06
CONTROL VOLTAGE
1
7
8
14
3.0Vdc
3.3Vdc
TEST DIAGRAM
SOLDER PROFILE
PACKAGE OUTLINE
120
C
150
C
180
C
260
C
0
220
C
360 Sec. Max.
120 S
Max.
10 S
60 S
Max.
Time
Temperature
260C
ENVIRONMENTAL CHARACTERISTICS
Temperature Cycle: Per MIL-STD-883, Method 1010, Condition B. -55C to 125C, 10 cycles, 10
minute dwell, 1minute transition.
Gross Leak Test: Per MIL-STD-202, Method 112, Condition D. No Bubbles in flourinert (FC-43) at
125C 5C for 20 seconds.
SOLDERING
Pin Solderabilit y: Per MIL-STD-883, Method 200. 8 hour steam age prior to 254C 5C Solder
pot dip, 95% Coverage.
Resistance to Solder Heat: Per MIL-STD-202, Method 210, Condition C. Wave: Topside board-
mount product, 260C 5C for 20 seconds.
MECHANICAL CHARACTERISTICS
Vibration: Per MIL-STD-202, Method 204, Condition A . 10G's peak, 10Hz to 500H z, 15 minute
cycles 12 times each perpendicu lar axis.
Shock: Per MIL-STD-202, Method 213, Condition F. 1 500G's, 0.5ms, half sine, 3 shocks per
direction.
Moisture Resistance: Per MIL-STD-202, Method 106. 95% RH @ 65 C, 10 cycles 10C to 65C.
PDF 
ZIP