ChipFind - документация

Электронный компонент: V762

Скачать:  PDF   ZIP

Document Outline

THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
WWW.CONWIN.COM
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
The Connor-Winfield V762 is a 3.3V
Voltage Controlled Crystal Oscillator
(VCXO) with LVPECL
Differential outputs and
enable/disable function. The V762
is designed for use with applications
utilizing a PLL system requiring low
jitter and tight frequency stability.
No multiplication schemes are used
in this oscillator design. The
surface mount package is designed
for high-density mounting and is
optimum for mass production.
1
2
V762 - 19.44MHz
VCXO
SERIES
CENTER
FREQUENCY
FEATURES
DESCRIPTION
ORDERING INFORMATION
19.44 to 200MHz
3.3V OPERATION
LOW JITTER <1pS RMS
ABSOLUTE PULL RANGE (APR):
50ppm
TEMPERATURE RANGE: -40 to 85C
DIFFERENTIAL LVPECL OUTPUTS
ENABLE / DISABLE FUNCTION
SURFACE MOUNT PACKAGE
TAPE AND REEL PACKAGING
RoHS COMPLIANT / LEAD FREE
3.3V 5 x 7mm SURFACE MOUNT HIGH FREQUENCY
LVPECL VCXO OSCILLATOR
V762
Vx574
02
10/05/06
C
W






0
6
3
5
V
7
6
2

1
9
.
4
4
M
Notes
1.0
Absolute pull range (APR) is the minimum guaranteed pul l range of the VCXO under all conditions over the lifetime
operation. Including calibration @ 25C, frequency vs. change in temperature, frequency vs. change in s upply voltage,
frequency vs. change in load, shock and vibration and aging for ten years. The APR is referenced to Fo. Positive Transfer
Function.
2.0
Outputs are enabled with no connection on pad 2. When oscillator is disabled both output s are in a high impedance state.
3.0
50 ohm termination into Vcc -2V or Thevein equivalent.
TABLE 6.0
Pin
Pin Connection
1
Control Voltage
2
Enable / Disable
3
Ground (Case)
4
Output Q
5
Output Q
6
Vcc
Output Enable Function
TABLE 7.0
Enable / Disable Function (Pad 2)
Output
No Connection
Enable
High
Enable
Low
Disable (High Impedance)
ABSOLU TE MAXI MUM RAT INGS
TABLE 1.0
PARAMETER
UNITS
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Storage Temperature
-55
-
125
C
Supply Voltage
(Vcc)
-0.5
-
4.6
Vdc
Control Voltage
(Vc)
-0.5
-
Vcc+0.5
Vdc
OPERATING SPECIFICATI ONS
TABLE 2.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Center Frequency
(Fo)
19.44
-
200
MHz
Operating Temperature Range
-40
-
85
C
Supply Voltage
(Vcc)
3.135
3.3
3.465
Vdc
Supply Current
(Icc)
-
-
100
mA
Jitter (BW=10Hz to 20MHz)
-
-
5
ps rms
Jitter (BW=12kHz to 20MHz)
-
-
1
ps rms
Typical Phase Noise for a 77.76 MHz
SSB Phase Noise at 10Hz offset
-
-55
-
dBc/Hz
SSB Phase Noise at 100Hz offset
-
-85
-
dBc/Hz
SSB Phase Noise at 1KHz offset
-
-115
-
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-135
-
dBc/Hz
SSB Phase Noise at 100KHz offset
-
-145
-
dBc/Hz
INPUT CHARACTERISTICS
TABLE 3.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
Control Voltage Range
(Vc)
0.3
1.65
3.0
Vdc
Absolute Pull Range (APR)
50
-
-
ppm
1
Monotonic Linearity
-10
-
10
%
Input Impedance
-
60K
-
Ohm
Modulation Bandwidth (3dB)
25
-
-
KHz
Enable Input Voltage (High)
(Vil)
2.275
-
-
Vdc
2
Disable Input Voltage (Low)
(Vih)
-
-
1.68
Vdc
2
LVPECL OUTPUT CHARACTERISTICS
TABLE 4.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
LOAD
-
-
50
Ohms
3
Voltage (High)
(Voh)
2.275
-
-
Vdc
(Low)
(Vol)
-
-
1.68
Vdc
Duty Cycle at 50% Level
45
50
55
%
Rise / Fall Time 20% to 80%
-
0.6
1.5
nS
PACKAG E CHARACTERISTICS
TABLE 5.0
Package
Hermetically sealed ceramic package with grounded metal cover
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
WWW.CONWIN.COM
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
2
2
Vx574
02
10/05/06
1.65V
E/D
2
.070
(1.8mm)
CW 0635
V762
19.44M
MAX
MAX
MAX
0
7
TEST CIRCUIT
SUGGESTED PAD LAYOUT
PACKAGE LAYOUT
120
C
150
C
180
C
260
C
0
220
C
360 Sec. Max.
120 S
Max.
10 S
60 S
Max.
Time
Temperature
260C
SOLDER PROFILE
OUTPUT WAVEFORM
Vcc1 = Vcc2 = 3.3Vdc