THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
The Connor-Winfield
VPLD52TM1E is a 3.3V
Voltage Controlled Crystal
Oscillator (VCXO) with
LVPECL Differential outputs.
The VPLD52TM1E is
designed for use with PLL
systems in SONET/SDH
systems requiring low jitter
and tight stability.
1
2
VPLD52TM1E - 212.5MHz
VCXO
SERIES
CENTER
FREQUENCY
FEATURES
DESCRIPTION
ORDERING INFORMATION
3.3V OPERATION
LVPECL DIFFERENTIAL OUTPUTS
ENABLE / DISABLE FUNCTION
LOW JITTER <1pS RMS
FREQUENCY STABILITY: 50ppm
APR: 100ppm MINIMUM
TEMPERATURE RANGE: 0 to 70C
SURFACE MOUNT PACKAGE
TAPE AND REEL PACKAGING
3.3V SURFACE MOUNT VCXO OSCILLATOR
VPLD52TM1E
Vx539
00
05/04/05
www.conwin.com
CW 0514
VPLD52TM1E
212.5M
Notes
1.0
Inclusive of calibration, frequency vs. temperature stability, supply voltage change, load change, s hock and
vibration and aging over ten years, Vc=1.65 Vdc.
2.0
Absolute pull range (APR) is the minimum guaranteed pull range of the VCXO under all conditions over lifetime
operation including aging for ten years. The APR is referenced to Fo.
3.0
When oscillator is disabled the true output is in a low state (Vol) and the complementary output is in the high state
(VoH)
4.0
50 ohm termination into Vcc-2V or Thevein equivalent.
ABSOLU TE MAX IMUM R ATINGS
TABLE 1.0
PARAMETER
UNITS
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Storage Temperature
-40
-
85
C
Supply Voltage
(Vcc)
-0.5
-
7.0
Vdc
Control Voltage
(Vc)
-0.5
-
7.0
Vdc
OPERATING SPECIFICATI ONS
TABLE 2.0
PARAMETER
MINIMUM
NOMINAL MAXIMUM
UNITS
NOTE
Center Frequency
(Fo)
16.384
-
225
MHz
Frequency Stability
-50
-
50
ppm
1
Operating Temperature Range
0
-
70
C
Supply Voltage
(Vcc)
3.135
3.3
3.465
Vdc
Supply Current
(Icc)
-
-
100
mA
Jitter (BW=10Hz to 20MHz)
-
-
5
ps rms
Jitter (BW=12kHz to 80MHz)
-
-
1
ps rms
SSB Phase Noise at 10Hz offset
-60
dBc/Hz
SSB Phase Noise at 100Hz offset
-
-90
-
dBc/Hz
SSB Phase Noise at 1KHz offset
-
-100
-
dBc/Hz
SSB Phase Noise at 10KHz offset
-
-135
-
dBc/Hz
SSB Phase Noise at 100KHz offset
-
-140
-
dBc/Hz
INPUT CHARACTERISTICS
TABLE 3.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
Control Voltage Range
(Vc)
0.3
1.65
3.0
Vdc
Absolute Pull Range (APR)
+/-100
-
-
ppm
2
Monotonic Linearity
-10
-
10
%
Input Impedance
-
50K
-
Ohm
Modulation Bandwidth (3dB)
10
-
-
KHz
Enable Input Voltage (Low)
(Vil)
-
-
1.68
Vdc
3
Disable Input Voltage (High)
(Vih)
2.275
-
-
Vdc
3
LOW VOLTAGE PECL OUTPUT CHARACTERISTICS
TABLE 4.0
PARAMETER
MINIMUM
NOMINAL
MAXIMUM
UNITS
NOTE
LOAD
-
-
50
Ohms
4
Voltage (High)
(Voh)
2.275
-
-
Vdc
(Low)
(Vol)
-
-
1.68
Vdc
Duty Cycle at 50% Level
45
50
55
%
Rise and Fall Times
-
-
1
nS
PACKAG E CHARACTERISTICS
TABLE 5.0
Package
Non-hermetic package consisting of an FR4 substrate with grounded metal
cover.
PROCESS RECOMMENDATIONS
TABLE 6.0
Solder Reflow
The component solder used internal to this device has a melting point of
221
C. The peak temperature inside the device should be less than or
equal to 220
C for a maximum of 10 seconds
Wash
Ultrasonic cleaning is not recommended.
THE CONNOR-WINFIELD CORP.
2111 COMPREHENSIVE DRIVE.
AURORA, IL 60505.
FAX (630) 851-5040.
PHONE (630) 851-4722.
P R O D U C T D A T A S H E E T
Specifications subject to change without notice.
DATA SHEET #:
REV:
DATE:
PAGE
OF
Copyright 2001 Connor-Winfield all rights reserved.
a
CRYSTAL CONTROLLED OSCILLATORS
2
2
Vx539
00
05/04/05
www.conwin.com
80%
50%
20%
V
P
L
D
5
2
T
M
1
E
2
1
2
.
5
M
C
W
Dimensional Tolerance:
.005" (.127mm)
2
E/D
Pin
Function
1
Control Voltage
2
Enable / Disable
3
Ground (Case)
4
Output Q
5
Comp Output Q
6
Vcc
1.65V
PDF 
ZIP