I-11
Noise
Filter
Specifications
No.
Items
TAC-04-683
TAC-06-683
TAC-10-683
TAC-20-683
TAC-30-683
1
Rated Voltage[V]
AC Three Phase 500
2
Rated Current[A]
4
6
10
20
30
3
Test Voltage (Terminal-Mounting Plate)
2,000 VAC (Cutoff Current = 100mA), 1minute at room temperature and humidity
4
Isolation Resistance (Terminal-Mounting Plate)
500 VDC 100M
W minute at room temperature and humidity
5
Leakage current 250/500V 60Hz
2.5mA/5.0mA max
6
Voltage drop
1.5V max
1.0V max
7
Safety agency approval temperatures
-25 to +85
C (Refer to Derating Curve)
8
Operating temperature
-40 to +85
C (Refer to Derating Curve)
9
Operating humidity
20 to 95%RH (Non condensing)
10
Storage temperature/humidity
-40 to +85
C/20 to 95%RH (Non condensing)
11
Vibration
10 to 55Hz, 19.6m/s
2
(2G), 3min. Period, 1hour each X, Y and Z axis
12
Impact
196.1m/s
2
(20G), 11ms Once each X, Y and Z axis
13
Safety agency approvals
UL1283, CSA C22.2 No.8 (C-UL) , DIN EN133200 VDE0565 Teil3-1, ENEC
14
Case size (without projection) /Mass
63
X64X128 mm (WXHXD) /620g max (Option : -D refer to external view)
TAC series
Three phase input type
TAC -10 -683 -
O
Ordering information
1Model Name
2Rated Current
3Line to ground capacitor code:See table 1.1.
table1.1 Line to ground capacitor code
Code
Leakage Current
(Input 250/500V 60Hz)
Line to ground
capacitor
(nominal value)
683
2.5mA/5.0mA max
68000pF
4Options
D :DIN rail installation type
1 2 3 4
Features of TAC series
Circuit Diagram
Derating Curve
Ambient Temperature [
C]
Load Factor [%]
70
80
90
-20
40
50
60
20
0
-40
-30
100
80
60
40
High-attenuation type of common mode noise from 150kHz to 1MHz
- Three Phase 500 VAC
- Quick and easy push-down terminal
Just connect the wires, push down and tighten
the screws with a screwdriver
*
The dimensions change when the option is set.
Refer to External view.
LOAD
Case
LINE
4
5
6
1
2
3
CY : Line to ground capacitor
CY
CY
: Mounting Plate
DIN rail installation type is option
The terminal cover is retracted inside the unit
I-13
Noise
Filter
TAC,TAH series
External view
4-
f
5.5
Terminal cover
7-M4
Mounting Hole
Protection Earth
64
12
19
20
63
50
0.5
83.5
128
118
0.5
(2)
Terminal cover
Input
Terminal
Input
Terminal
Output
Terminal
Output
Terminal
Output
Terminal
Mounting Plate
Name Plate
Tolerance :
1
Mass : 620g or less
Mounting Plate : Iron (surface finishing:nickel plating) t=1.0
Case : PBT
Dimensions in mm
Terminal block screw tighting torque M4:1.6N
-
m (16.9kgf
-
cm) max
Closed the terminal cover
50
(2.5)
This product is shipped in the following condition, because it is equipped with push-down terminals.
1The terminal cover is retracted inside the unit.
2The screws for connecting the terminals are held in the up right position.
Note when installing the noise
fi lter on a DIN rail.
When the noise fi lter is grounded through the
DIN rail, the proper noise attenuation may not be
achieved.
Be sure to connect the protection earth (PE) of
the noise fi lter body to the earth.
DIN rail
7-M4
Mounting Plate
Protection Earth
(11)
108
7
(9)
12
19
20
83.5
(2)
64
63
Terminal cover
Terminal cover
Input
Terminal
Input
Terminal
Output
Terminal
Output
Terminal
Output
Terminal
Tolerance :
1
Mass : 620g or less
Mounting Plate : Iron (surface finishing:nickel plating) t=1.0
Case : PBT
Dimensions in mm
Terminal block screw tighting torque M4:1.6N
-
m (16.9kgf
-
cm) max
Name Plate
Closed the terminal cover
50
(2.5)
10
Standard Type
DIN rail installation Type
Name Plate
DIN rail
PDF 
ZIP