Note: All information contained in this data sheet has been carefully checked and is believed to be accurate as of the date of publication; however, this data sheet cannot be a "controlled document". Current revisions, if any, to these
specifications are maintained at the factory and are available upon your request. We recommend checking the revision level before finalization of your design documentation.
2001 Elantec Semiconductor, Inc.
E
L
1
5
0
1
C
-
P
r
o
d
u
c
t
B
r
i
e
f
General Description
The EL1501C contains two wideband high-voltage drivers and two
receive amplifiers. It is designed to drive 45V
P-P
signals at 2MHz into
a 200
load differentially with very low distortion. The receive ampli-
fiers also provide very low distortion and noise, and with external
resistors can be wired as a hybrid coupler.
All amplifiers are of the current-feedback type, giving high slewrates
while consuming moderate power. They retain frequency response
over a wide range of externally set gains.
The EL1501C operates on 5V to 15V supplies, and retains its band-
widths and linearities over the supply range.
Eight center package pins are used as ground connections and heat
spreaders, allowing a dissipation of 2W at the maximum ambient tem-
perature of 85C.
Connection Diagrams
Features
Complete ADSL differential driver
and receiver
45V
P-P
differential output drive
into 200
-60dB typical output distortion at
full output at 2MHz
-73dB typical receive distortion at
15V
P-P
levels at 2MHz
Drives 8 single-ended video loads,
or 4 S-VHS loads, or 4 differential
video loads
Power surface-mount package
Applications
ADSL line interface
HDSL line driver
Video distribution amplifier
Video twisted-pair line driver
Ordering Information
Part No
Temp. Range
Package
Outline #
EL1501CM
-40C to +85C
20-Lead SO
MDP0027
EL1501C - Product Brief
Differential Line Driver/Receiver
M
a
r
c
h
1
9
9
5
R
e
v
.
A
2
EL1501C - Product Brief
Differential Line Driver/Receiver
E
L
1
5
0
1
C
-
P
r
o
d
u
c
t
B
r
i
e
f
General Disclaimer
Specifications contained in this data sheet are in effect as of the publication date shown. Elantec, Inc. reserves the right to make changes in the cir-
cuitry or specifications contained herein at any time without notice. Elantec, Inc. assumes no responsibility for the use of any circuits described
herein and makes no representations that they are free from patent infringement.
WARNING - Life Support Policy
Elantec, Inc. products are not authorized for and should not be used
within Life Support Systems without the specific written consent of
Elantec, Inc. Life Support systems are equipment intended to sup-
port or sustain life and whose failure to perform when properly used
in accordance with instructions provided can be reasonably
expected to result in significant personal injury or death. Users con-
templating application of Elantec, Inc. Products in Life Support
Systems are requested to contact Elantec, Inc. factory headquarters
to establish suitable terms & conditions for these applications. Elan-
tec, Inc.'s warranty is limited to replacement of defective
components and does not cover injury to persons or property or
other consequential damages.
M
a
r
c
h
1
9
9
5
R
e
v
.
A
Printed in U.S.A.
Elantec Semiconductor, Inc.
675 Trade Zone Blvd.
Milpitas, CA 95035
Telephone: (408) 945-1323
(888) ELANTEC
Fax:
(408) 945-9305
European Office: +44-118-977-6020
Japan Technical Center: +81-45-682-5820
PDF 
ZIP