R
EM6153
Copyright 2006, EM Microelectronic-Marin SA
1
www.emmicroelectronic.com
06/06, rev. B, prelim.
5V Automotive Regulator with Inhibit Input and
Windowed Watchdog
Description
The EM6153 offers a high level of integration by combining
voltage regulation, voltage monitoring and software
monitoring using a windowed watchdog.
A comparator monitors the voltage applied at the V
IN
input
comparing it with an internal voltage reference V
REF
. The
power-on reset function is initialized after V
IN
reaches V
REF
and takes the reset output inactive after a delay T
POR
depending on external resistance R
OSC
. The reset output goes
active low when the V
IN
voltage is less than V
REF
. The
RES
and
EN
outputs are guaranteed to be in a correct state for a
regulated output voltage as low as 1.2 V. The watchdog
function monitors software cycle time and execution.
If software clears the watchdog too quickly (incorrect cycle
time) or too slowly (incorrect execution) it will cause the
system to be reset. For enhanced security, the watchdog
must be serviced within an "open" time window. During the
remaining time, the watchdog time window is "closed" and a
reset will occur should a
TCL
pulse be received by the
watchdog during this "closed" time window. The ratio of the
open/closed window is either 33%/67% or 67%/33%.
The system ENABLE output prevents critical control functions
being activated until software has successfully cleared the
watchdog three times. Such a security could be used to
prevent motor controls being energized on repeated resets of
a faulty system.
When the microcontroller goes in stand-by mode or stops
working, no signal is received on the
TCL
input and the
EM6153 (version 55) goes into a stand-by mode in order to
save power (CAN-bus sleep detector).
In EM6153, the voltage regulator has a low dropout voltage
and a low quiescent current of 75
A. The quiescent current
increases only slightly in dropout prolonging battery life. Built-
in protection includes a positive transient absorber for up to
45 V (load dump) and the ability to survive an unregulated
input voltage of -42 V (reverse battery). The input may be
connected to ground or to a reverse voltage without reverse
current flowing from the output to the input.
Features
Low quiescent current 90
A
Very low OFF current consumption < 1uA
-40C to +125C temperature range
Highly accurate 5 V, 150 mA guaranteed output (actual
maximum current depends on power dissipation)
Low dropout voltage, typically 250 mV at 100 mA
Unregulated DC input can withstand -42 V reverse battery
and +45 V power transients
Fully operational for unregulated DC input voltage up to
40 V and regulated output voltage down to 3.5 V
No reverse output current
Very low temperature coefficient for the regulated output
Current
limiting
Windowed watchdog with an adjustable time windows,
guaranteeing a minimum time and a maximum time
between software clearing of the watchdog
Time base accuracy
8% (at 100ms)
Sleep mode function (V55)
Adjustable threshold voltage using external resistors
Adjustable power on reset (POR) delay using one
external resistor
Open-drain active-low RESET output
Reset output guaranteed for regulated output voltage
down to 1.2 V
System ENABLE output offers added security
Qualified according to AEC-Q100
Green SO-16 Exposed pad package (RoHS compliant)
Applications
Automotive
systems
Industrial
Home
security
systems
Telecom / Networking
Computers
Set top boxes
Typical Operating Configuration
Fig.
1
Selection Table
Part Number
V
REF
Closed
Window
Open
Window
CAN-bus sleep
detector
EM6153V50 1.52
V
67%
33%
NO
EM6153V53 1.52
V
33%
67%
NO
EM6153V55 1.275
V
67%
33%
YES
Please refer to Fig. 4 for more information about the
open/closed window of the watchdog.
EM MICROELECTRONIC -
MARIN SA
5V
+
V
SS
GND
Unregulated
Voltage
INPUT
OUTPUT
EM6153
RES
EN
TCL
V
IN
M
i
cr
o
pro
ce
ss
o
r
V
DD
I/O
RES
I/O
R
OSC
10uF
100nF
22uF
R
OSC
R
1
R
2
+
INH
Inhibit
V
DD
R
EM6153
Copyright 2006, EM Microelectronic-Marin SA
2
www.emmicroelectronic.com
06/06, rev. B, prelim.
V
SS
R
OSC
OUTPUT
RES
EN
TCL
V
IN
Ex. Pad SO-16
EM6153
NC
INPUT
NC
16
15
14
13
12
11
10
9
1
2
3
4
5
6
7
8
NC
NC
NC
NC
INH
V
DD
Ordering Information
Part Number
Version
V
REF
Package
Delivery
Form
Package
Marking
EM6153V50ES16B+
V50
1.520 V
ExPadSO-16
Tape & Reel, 2500pcs
EM6153 050
EM6153V53ES16B+
V53
1.520 V
ExPadSO-16
Tape & Reel, 2500pcs
EM6153 053
EM6153V55ES16B+
V55
1.275 V
ExPadSO-16
Tape & Reel, 2500pcs
EM6153 055
Note: the "+" symbol at the end of the part number means that this product is RoHS compliant (green).
Pin Assignment and Description
SO-16 Exposed Pad
Name
Function
2
EN
Push-pull active low enable output
3
RES
Open drain active low reset output. RES
must be pulled up to V
OUTPUT
even if unused
4
TCL
Watchdog timer clear input signal
5 V
SS
GND
terminal
6
INPUT
Voltage regulator input
8
INH
Inhibit input
12
OUTPUT Voltage regulator output
13 V
DD
Watchdog power supply
14 R
OSC
R
OSC
input for RC oscillator tuning
15 V
IN
Voltage comparator input
1, 7, 9, 10, 11, 16
NC
No connect
Exposed Pad
Connect to V
SS
or left floating
Block Diagram EM6153
Fig. 3
RES
EN
TCL
Voltage
Regulator
Voltage
Reference
Voltage
Reference
Current
Controlled
Oscillator
-
+
V
REF
Comparator
Reset
Control
Timer
Enable
Logic
INPUT
V
IN
R
OSC
OUTPUT
Open drain
output RES
V
DD
R
EM6153
Copyright 2006, EM Microelectronic-Marin SA
3
www.emmicroelectronic.com
06/06, rev. B, prelim.
Absolute Maximum Ratings
Parameter Symbol
Conditions
Continuous voltage at INPUT and
INH to V
SS
V
INPUT
-0.3 to +40V
Transients on INPUT for
t < 100 ms and duty cycle 1%
V
TRANS
Up to +45V
Max. voltage at any signal pin
V
MAX
V
OUTPUT
+ 0.3V
Min. voltage at any signal pin
V
MIN
V
SS
0.3V
Reverse supply voltage on
INPUT and INH
V
REV
-42V
Storage temperature
T
STO
-65 to +150 C
ESD
According to MIL-STD-883
method 3015.7
V
Smax
2000V
Table 1
Stresses above these listed maximum ratings may cause
permanent damages to the device. Exposure beyond
specified operating conditions may affect device reliability or
cause malfunction.
Decoupling Methods
The input capacitor is necessary to compensate the line
influences. A resistor of approx. 1
connected in series
with the input capacitor may be used to damp the oscillation
of the input capacitor and input inductance. The ESR value
of the capacitor plays a major role regarding the efficiency of
the decoupling. It is recommended also to connect a
ceramic capacitor (100 nF) directly at the IC's pins. In
general the user must assure that pulses on the input line
have slew rates lower than 1 V/s. On the output side, the
capacitor is necessary for the stability of the regulation
circuit. The stability is guaranteed for values of 10 F or
greater. It is especially important to choose a capacitor with
a low ESR value. Tantalum capacitors are recommended.
See the notes related to Table 2. Special care must be
taken in disturbed environments (automotive, proximity of
motors and relays, etc.).
Handling Procedures
This device has built-in protection against high static
voltages or electric fields; however, it is advised that normal
precautions be taken as for any other CMOS component.
Unless otherwise specified, proper operation can only occur
when all terminal voltages are kept within the voltage range.
At any time, all inputs must be tied to a defined logic voltage
level.
Operating Conditions
Parameter
Symbol Min. Max.
Units
Operating junction
temperature
T
j
-40
+125
C
INPUT voltage (note 1, 2)
V
INPUT
5.5 40 V
RES
and
EN
guaranteed
(note 3)
V
OUTPUT
1.2
V
OUTPUT current (note 4)
I
OUTPUT
150 mA
Comparator input voltage
V
IN
0
V
OUTPUT
V
RC-oscillator programming R
OSC
10 1000 k
Package thermal resistance
from junction to ambient :
Exp. Pad SO-16 150 MILS
(note 5)
R
th(j-a)
30
90
C/W
Table 2
Note 1:
full operation guaranteed. To achieve the load regulation specified in Table 3 a 10
F capacitor or greater is required on the INPUT,
see Fig. 1b. The 10
F must have an effective resistance
4
and a resonant frequency above 500 kHz.
Note 2:
a
10
F load capacitor and a 100 nF decoupling capacitor are required on the regulator OUTPUT for stability. The 10
F must have
an effective series resistance of
4
and a resonant frequency above 500 kHz.
Note 3:
RES
must be pulled up externally to V
OUTPUT
even if it is unused. (
RES
and EN
are used as inputs by EM test)
Note 4:
the OUTPUT current will not apply to the full range of input voltage. Power dissipation that would require the EM6153 to work above
the maximum junction temperature (+125C) must be avoided.
Note 5:
the thermal resistance specified assumes the package is soldered to a PCB. A typical value of 51C/W has been obtained with a dual
layer board, with the slug soldered to the heat-sink area of the PCB (See Figure 14)
R
EM6153
Copyright 2006, EM Microelectronic-Marin SA
4
www.emmicroelectronic.com
06/06, rev. B, prelim.
Electrical Characteristics
V
INPUT
= 13.5 V, C
L
= 10
F + 100 nF, C
INPUT
= 22
F, V
INH
= 5 V, V
DD
connected to V
OUTPUT
, T
j
= -40 to +125C, unless
otherwise specified
Parameter Symbol Test
Conditions
Min.
Typ.
Max.
Unit
Supply current OFF mode
I
SS
R
OSC
= don't care, TCL = V
OUTPUT
,
V
IN
= 0 V, V
INH
= 0 V, T
j
< 100C
0 1
A
Supply current in standby mode and sleep
mode for V55 (note 1)
I
SS
R
OSC
= don't care, TCL = V
OUTPUT
,
V
IN
= 0 V, I
L
= 100
A
80
135
A
Supply current (note1)
I
SS
R
OSC
= 100 k
, I/P
S
at V
OUTPUT
,
O/P
S
1 M
to V
OUTPUT
, I
L
= 100
A
90
140
A
Supply current
I
SS
R
OSC
= 100 k
, I/P
S
at V
OUTPUT
,
O/P
S
1 M
to V
OUTPUT
, I
L
= 50 mA
1.7 4 mA
Voltage regulator
Output voltage
V
OUTPUT
5 mA
I
L
100 mA
4.85
5
5.15
V
Line regulation (note 2)
V
LINE
6 V
V
INPUT
28 V, I
L
= 1 mA
5
30
mV
Load regulation (note 2)
V
L
1
mA
I
L
100 mA, V
INPUT
= 6 V
50
95
mV
Dropout voltage (note 3)
V
DROPOUT
I
L
= 100 mA
250
500
mV
Current limit
I
Lmax
OUTPUT tied to V
SS
, V
INPUT
= 6 V
150
200
500
mA
Supervisory and watchdog
RES
&
EN
V
OUTPUT
= 4.5 V, I
OL
= 8 mA
0.25
0.45
V
Output Low Voltage
V
OL
V
OUTPUT
= 1.2 V, I
OL
= 0.5 mA
0.04
0.2
V
EN
V
OUTPUT
= 4.5 V, I
OH
= -1 mA
3.5
4.1
V
Output High Voltage
V
OH
V
OUTPUT
= 1.2 V, I
OH
= -20
A 0.9
1.05
V
TCL
Input Low Level
V
IL
V
SS
0.5 V
TCL
Input High Level
V
IH
2.5 V
OUTPUT
V
INH
Input On Voltage
V
INH, on
3.5
V
INH
Input Off Voltage
V
INH, off
0.8
V
INH
current I
INH
V
INH
= 5 V
4
8
A
TCL
Leakage current
I
LI
V
SS
V
TCL
V
OUTPUT
0.05
A
Comparator reference (note 4, 5)
Version
V50
1.475 1.520 1.565
V
V
REF
Version
V53
1.475 1.520 1.565
V
Version
V55
1.235 1.275 1.315
V
Comparator hysteresis (note 5)
V
HY
2
mV
V
IN
input resistance
R
VIN
100
M
Table 3
Note 1:
if INPUT is connected to V
SS
, no reverse current will flow from the OUTPUT to the INPUT.
Note 2:
regulation is measured at constant junction temperature using pulse testing with a low duty cycle.
Note 3:
the dropout voltage is defined as the INPUT to OUTPUT differential, measured with the input voltage equal to 5.0 V.
Note 4:
the comparator and the voltage regulator have separate voltage references (see "Block Diagram" Fig. 3).
Note 5:
the comparator reference is the power-down reset threshold. The power-on reset threshold equals the comparator reference voltage
plus the comparator hysteresis (see Fig. 5).
R
EM6153
Copyright 2006, EM Microelectronic-Marin SA
5
www.emmicroelectronic.com
06/06, rev. B, prelim.
Timing Characteristics
V
INPUT
= 13.5 V, I
L
= 100
A, C
L
= 10
F + 100 nF, C
INPUT
= 22
F, V
INH
= 5 V, T
j
= -40 to + 125
C, unless otherwise specified
Parameter Symbol Test
Conditions
Min.
Typ.
Max.
Units
Propagation delay TCL to Output Pins
T
DIDO
250 500 ns
V
IN
sensitivity
T
SEN
V
INhigh
=1.1
x
V
REF
, V
INlow
=0.9
x
V
REF
0.5 3 15
s
Watchdog Reset Pulse Period
T
WDRP
TCL
inactive
T
CW
+ T
OW
+ T
WDR
ms
Version V50
Power-on Reset delay
T
POR
R
OSC
= 121.6 k
1% 91.6
100
108.3
Closed Window Time
T
CW
74 80 85.76
Open Window Time
T
OW
37 40 42.88
ms
Watchdog Time
T
WD
92.5 100 107.2
Watchdog Reset Pulse Width if no TCL
T
WDR
2.25 2.5 2.75
Version V53
Power-on Reset delay
T
POR
R
OSC
= 23.2 k
1%
4.57 5.0 5.44
Closed Window Time
T
CW
9.24 10 10.77
Open Window Time
T
OW
18.48 20 21.54
ms
Watchdog Time
T
WD
18.48 20 21.54
Watchdog Reset Pulse Width if no TCL
T
WDR
0.56 0.625 0.69
Version V55
Power-on Reset delay
T
POR
R
OSC
= 107.5 k
1% 91.6
100
108.3
Closed Window Time
T
CW
74 80 85.76
Open Window Time
T
OW
37 40 42.88
Watchdog Time
T
WD
92.5 100 107.2
ms
Watchdog Reset Pulse Width if no TCL
T
WDR
2.25 2.5 2.75
Watchdog Reset Pulse Width in Sleep Mode
T
WDRS
R
OSC
off; R
INT
=1M
2.8 3.2 3.6
Watchdog Reset Pulse Period in Sleep Mode
T
WDRPS
TCL inactive
750
1100 1450
Table 4
For different values of T
WD
and R
OSC
, see figures 9 to 11.
Timing Waveforms
Watchdog Timeout Period
Fig. 4
T
CW
(closed window)
T
OW
(open)
T
WD
80
120
Time [ms]
Watchdog
timer reset
( V30, V50 and V55 have similar ratios for T
CW
and T
OW
)
Version V50:
T
CW
(closed)
T
OW
(open)
10
30
Time [ms]
Watchdog
timer reset
Version V53:
For R
OSC
=121.6 kOhm
For R
OSC
=23.2 kOhm
T
WD
PDF 
ZIP