2
09/06
Please read Cautions and warnings and
Important notes at the end of this document.
To IEC 61596
For transformers featuring high inductance
and low overall height
For power applications
Delivery mode: sets
Magnetic characteristics (per set)
l/A = 0.51 mm
1
l
e
= 40 mm
A
e
= 78 mm
2
A
min
= 60 mm
2
V
e
= 3120 mm
3
Approx. weight 27.5 g/set
Gapped
Ungapped
Material
A
L
value
nH
s
approx.
mm
e
Ordering code
N87
200
3%
0.47
82
B65847A0200A087
Material
A
L
value
nH
e
P
V
W/set
Ordering code
N30
6700 +30/20% 2730
B65847A0000R030
T65
10200 +30/20% 4160
B65847A0000R065
T38
18700 +40/30% 7630
B65847A0000Y038
N87
4000 +30/20% 1630
< 1.2 (200 mT, 100 kHz, 100 C)
B65847A0000R087
FEP0031-N
10
15,3
4,50,2
_
0,7
0,5
9
_
16,1+0,8
_
21,6
0,4
14+0,6
1
_
24,5
s
)
gapped (one-sided)
)
B65847
Core
EP 20
3
09/06
Please read Cautions and warnings and
Important notes at the end of this document.
Coil former
Material:
GFR thermosetting plastic (UL 94 V-0, insulation class to IEC 60085:
F max. operating temperature 155 C), color code green
Vyncolit/X611
[E167521 (M)], VYNCOLIT NV
Solderability: to IEC 60068-2-20, test Ta, method 1 (aging 3): 235 C, 2 s
Resistance to soldering heat: to IEC 60068-2-20, test Tb, method 1B: 350 C, 3.5 s
Winding:
see Data Book 2007, chapter "Processing notes, 2.1"
Squared pins.
Sections
A
N
mm
2
l
N
mm
A
R
value
Terminals
Ordering code
1
35.4
40.6
39.5
10
B65848D1010D001
FEP0032-M
Ground 1,3+0,2
2,54
1+0,15
2
+0,4
3,2
0,2
_
9,1+0,2
15,9 max.
6
0,3
26,8
_
1
22,8
0,75
0,3
_
0,75
10,2 max.
including pin 1
Marking of pin row
0,45
13,9 0,1
_
0,75
B65848
Accessories
EP 20
4
09/06
Please read Cautions and warnings and
Important notes at the end of this document.
Mounting assembly
The set comprises a yoke and a clamp
Yoke
Made of nickel silver (0.4 mm) with ground terminal (tinned)
Clamp
Spring clamp, made of nickel silver (0.4 mm)
Yoke
Clamp
Ordering code
Complete mounting assembly
B65848A2000X000
FEP0033-W
24.8
17.6
23
4.6
3.5
12
1 x 0.4
2.50.1
25.6 max.
FEP0034-E
21.5
25
12
B65848
Accessories
EP 20
5
09/06
Ferrites and accessories
Cautions and warnings
Mechanical stress and mounting
Ferrite cores have to meet mechanical requirements during assembling and for a growing number
of applications. Since ferrites are ceramic materials one has to be aware of the special behavior
under mechanical load.
As valid for any ceramic material, ferrite cores are brittle and sensitive to any shock, fast changing
or tensile load. Especially high cooling rates under ultrasonic cleaning and high static or cyclic loads
can cause cracks or failure of the ferrite cores.
For detailed information see Data Book 2007, chapter "General Definitions, 8.1".
Effects of core combination on A
L
value
Stresses in the core affect not only the mechanical but also the magnetic properties. It is apparent
that the initial permeability is dependent on the stress state of the core. The higher the stresses are
in the core, the lower is the value for the initial permeability. Thus the embedding medium should
have the greatest possible elasticity.
For detailed information see Data Book 2007, chapter "General Definitions, 8.2".
Heating up
Ferrites can run hot during operation at higher flux densities and higher frequencies.
NiZn-materials
The magnetic properties of NiZn-materials can change irreversible in high magnetic fields.
Processing notes
The start of the winding process should be soft. Else the flanges may be destroid.
To strong winding forces may blast the flanges or squeeze the tube that the cores can no more
be mount.
To long soldering time at high temperature (>300 C) may effect coplanarity or pin arrangement.
Not following the processing notes for soldering of the J-leg terminals may cause solderability
problems at the transformer because of pollution with Sn oxyd of the tin bath or burned insulation
of the wire. For detailed information see Data Book 2007, chapter "Processing notes, 2.2".
The dimensions of the hole arrangement have fixed values and should be understood as a
recommendation for drilling the printed circuit board. For dimensioning the pins, the group of
holes can only be seen under certain conditions, as they fit into the given hole arrangement. To
avoid problems when mounting the transformer, the manufacturing tolerances for positioning the
customers' drilling process must be considered by increasing the hole diameter.
PDF 
ZIP