ChipFind - документация

Электронный компонент: D202I

Скачать:  PDF   ZIP
Key Features:
2W Output Power
3,000 VDC Isolation
Miniature SIP Case
Single & Dual Outputs
>2 MHour MTBF
28 Standard Models
Industry Standard Pin-Out
MicroPower Direct
232 Tosca Drive
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
D200I
High Isolation
High Isolation
Miniature, 2W SIP
Miniature, 2W SIP
DC/DC Con vert ers
DC/DC Con vert ers
Series
Electrical Specifi cations
Specifi cations typical @ +25C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice.
Input
Parameter
Conditions
Min.
Typ.
Max.
Units
Input Voltage Range
5 VDC Input
4.5
5.0
5.5
VDC
12 VDC Input
10.8
12.0
13.2
24 VDC Input
21.6
24.0
26.4
48 VDC Input
42.0
48.0
52.0
Input Filter
Internal Capacitor
Reverse Polarity Input Current
0.3
A
Output
Parameter
Conditions
Min.
Typ.
Max.
Units
Output Voltage Accuracy
1.0
3.0
%
Output Voltage Balance
Dual Output , Balanced Loads
1.0
%
Line Regulation
For Vin Change of 1%
1.2
%
Load Regulation (Note 1)
See Model Selection Guide
Ripple & Noise (20 MHz) (Note 2)
75
mV P - P
Output Power Protection
120
%
Temperature Coeffi cient
0.02
%/C
Output Short Circuit
Momentary (0.5 Sec.)
General
Parameter
Conditions
Min.
Typ.
Max.
Units
Isolation Voltage
60 Seconds
3,000
VDC
Isolation Resistance
500 VDC
1,000
M
Isolation Capacitance
100 kHz, 1V
60
pF
Switching Frequency
125
kHz
Environmental
Parameter
Conditions
Min.
Typ.
Max.
Units
Operating Temperature Range
Ambient
-40
+25
+85
C
Operating Temperature Range
Case
+100
C
Storage Temperature Range
-40
+125
C
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
Physical
Case Size
(5V, 12V & 24V Input Models)
0.76 x 0.24 x 0.37 Inches (19.5 x 6.0 x 9.5 mm)
Case Size
(48V Input Models)
0.76 x 0.28 x 0.37 Inches (19.5 x 7.2 x 9.5 mm)
Case Material
Non-Conductive Black Plastic (UL94-V0)
Weight
0.09 Oz (2.7g)
Reliability Specifi cations
Parameter
Conditions
Min.
Typ.
Max.
Units
MTBF
MIL HDBK 217F, 25C, Gnd Benign
2.0
MHours
Absolute Maximum Ratings
Parameter
Conditions
Min.
Typ.
Max.
Units
Input Voltage Surge (1 Sec)
5 VDC Input
-0.7
9.0
VDC
12 VDC Input
-0.7
18.0
24 VDC Input
-0.7
30.0
48 VDC Input
-0.7
55.0
Lead Temperature
1.5 mm From Case For 10 Sec
260
C
Internal Power Dissipation
All Models
650
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Notes:
All dimensions are typical in inches (mm)
Tolerance
x.xx
=
0.01 (
0.25)
Pin 1 is marked by a "dot" or indentation on the side of the unit
Notes:
1. Output load regulation is specifi ed for a load change of 20% to 100%.
2. When measuring output ripple, it is recommended that an external ceramic capacitor (approx 10 F)
be placed from the +Vout pin to the -Vout pin for single output units and from each output to common
for dual output units.
3. All 3.3, 5 and 5 VDC output models may be operated to +85C ambient with an unobstructed airfl ow
of 3.6 ft/S (1.1 m/S).
4. The 5V, 12V and 24V input units do not require external components to operate, but the use of an
input capacitor (10 F) may enhance performance in some applications. An output capacitor (1.0 F
to 10 F) may be used to reduce ripple. The 48V input models require an input capacitor of 4.7 uF to
47 uF (dependent upon the application).
5. Dual output units may be connected to provide a 10V, 24V or 30 VDC output. To do this, connect the
load across the positive (+Vout) and negative (-Vout) outputs and fl oat the output common.
6. It is recommended that a fuse be used on the input of a power supply for protection. See the table above
for the correct rating.
Derating Curve
MicroPower Direct
www.micropowerdirect.com
232 Tosca Drive Stoughton, MA 02072
TEL: (781) 344-8226
FAX: (781) 344-8481
E-Mail: sales@micropowerdirect.com
Model Selection Guide
Mechanical Dimensions
Pin Connections
Single Output
(F Max)
470
Dual Output
(F Max)
390
Capacitive
Load
Model
Number
Input
Output
Load
Regulation
(%, Max)
Effi ciency
(%, Typ)
Fuse Rating
Slow-Blow
(mA)
Voltage (VDC)
Current (mA)
Voltage
(VDC)
Current
(mA, Max)
Current
(mA, Min)
Nominal
Range
Full-Load No-Load
D201I
5
4.5 - 5.5
533
35
3.3
400.0
10.0
12
75
1,000
D202I
5
4.5 - 5.5
513
35
5.0
400.0
8.0
12
78
1,000
D203I
5
4.5 - 5.5
495
35
12.0
165.0
3.0
8
80
1,000
D204I
5
4.5 - 5.5
499
35
15.0
133.0
2.5
8
80
1,000
D205I
5
4.5 - 5.5
533
35
5.0
200.0
4.0
12
75
1,000
D206I
5
4.5 - 5.5
504
35
12.0
83.0
1.5
8
79
1,000
D207I
5
4.5 - 5.5
501
35
15.0
66.0
1.0
8
79
1,000
D211I
12
10.8 - 13.2
204
25
3.3
400.0
10.0
8
67
500
D212I
12
10.8 - 13.2
212
25
5.0
400.0
8.0
8
78
500
D213I
12
10.8 - 13.2
196
25
12.0
165.0
3.0
8
85
500
D214I
12
10.8 - 13.2
200
25
15.0
133.0
2.5
8
83
500
D215I
12
10.8 - 13.2
216
25
5.0
200.0
4.0
8
77
500
D216I
12
10.8 - 13.2
201
25
12.0
83.0
1.5
8
82
500
D217I
12
10.8 - 13.2
200
25
15.0
66.0
1.0
8
82
500
D221I
24
21.6 - 26.4
92
10
3.3
400.0
10.0
8
74
200
D222I
24
21.6 - 26.4
108
10
5.0
400.0
8.0
8
77
200
D223I
24
21.6 - 26.4
101
10
12.0
165.0
3.0
8
81
200
D224I
24
21.6 - 26.4
101
10
15.0
133.0
2.5
8
82
200
D225I
24
21.6 - 26.4
108
10
5.0
200.0
4.0
8
77
200
D226I
24
21.6 - 26.4
102
10
12.0
83.0
1.5
8
81
200
D227I
24
21.6 - 26.4
99
10
15.0
66.0
1.0
8
84
200
D231I
48
42.0 - 52.0
59
10
3.3
400.0
10.0
8
70
100
D232I
48
42.0 - 52.0
54
10
5.0
400.0
8.0
8
77
100
D233I
48
42.0 - 52.0
51
10
12.0
165.0
3.0
8
81
100
D234I
48
42.0 - 52.0
50
10
15.0
133.0
2.5
8
82
100
D235I
48
42.0 - 52.0
54
10
5.0
200.0
4.0
8
76
100
D236I
48
42.0 - 52.0
51
10
12.0
83.0
1.5
8
81
100
D237I
48
42.0 - 52.0
50
10
15.0
66.0
1.0
8
82
100
Pin
Single
Dual
1
+Vin
+Vin
2
-Vin
-Vin
5
-Vout
-Vout
6
No Pin
Common
7
+Vout
+Vout