ChipFind - документация

Электронный компонент: D204RP

Скачать:  PDF   ZIP
Key Features:
2W Output Power
Short Circuit Protection
Tight Line/Load Regulation
1,000 VDC Isolation
Miniature SIP Case
>1.5 MHour MTBF
15 Standard Models
MicroPower Direct
232 Tosca Drive
Stoughton, MA 02072
USA
T: (781) 344-8226
F: (781) 344-8481
E: sales@micropowerdirect.com
W: www.micropowerdirect.com
D200RP
Short Circuit Protected
Short Circuit Protected
Regulated, 2W SIP
Regulated, 2W SIP
DC/DC Con vert ers
DC/DC Con vert ers
Series
Input
Parameter
Conditions
Min.
Typ.
Max.
Units
Input Voltage Range
5 VDC Input
4.5
5.0
5.5
VDC
12 VDC Input
10.8
12.0
13.2
24 VDC Input
21.6
24.0
26.4
Input Filter
(Pi) Filter
Reverse Polarity Input Current
0.3
A
Output
Parameter
Conditions
Min.
Typ.
Max.
Units
Output Voltage Accuracy
2.0
%
Line Regulation
For Vin Min to Max
0.5
%
Load Regulation (Note 1)
0.5
%
Ripple & Noise (20 MHz) (Note 2)
75
mV P - P
Output Power Protection
120
%
Temperature Coeffi cient
0.02
%/C
Output Short Circuit
Continuous
General
Parameter
Conditions
Min.
Typ.
Max.
Units
Isolation Voltage
60 Seconds
1,000
VDC
Isolation Resistance
500 VDC
1,000
M
Isolation Capacitance
100 kHz, 1V
60
pF
Switching Frequency
40
kHz
Environmental
Parameter
Conditions
Min.
Typ.
Max.
Units
Operating Temperature Range
Ambient
-25
+25
+71
C
Operating Temperature Range
Case
-25
+85
C
Storage Temperature Range
-40
+125
C
Cooling
Free Air Convection
Humidity
RH, Non-condensing
95
%
Physical
Case Size
1.26 x 0.32 x 0.55 Inches (32.0 x 8.0 x 14.0 mm)
Case Material
Non-Conductive Black Plastic (UL94-V0)
Weight
0.17 Oz (4.8g)
Reliability Specifi cations
Parameter
Conditions
Min.
Typ.
Max.
Units
MTBF
MIL HDBK 217F, 25C, Gnd Benign
1.5
MHours
Absolute Maximum Ratings
Parameter
Conditions
Min.
Typ.
Max.
Units
Input Voltage Surge (1 Sec)
5 VDC Input
-0.7
9.0
VDC
12 VDC Input
-0.7
18.0
24 VDC Input
-0.7
30.0
Lead Temperature
1.5 mm From Case For 10 Sec
260
C
Internal Power Dissipation
All Models
450
mW
Caution: Exceeding Absolute Maximum Ratings may damage the module. These are not continuous operating ratings.
Electrical Specifi cations
Specifi cations typical @ +25C, nominal input voltage & rated output current, unless otherwise noted. Specifi cations subject to change without notice.
Notes:
1. Output load regulation is specifi ed for a load change
of 20% to 100%.
2. When measuring output ripple, it is recommended
that an external 0.33 F ceramic capacitor be placed
from the +Vout pin to the -Vout pin.
3. Operation at no-load will not damage these units.
However, they may not meet all specifi cations.
4. These do not require external components to operate,
but the use of a low ESR capacitor (approximately
10 uF, ESR <1.0 at 100 kHz) mounted close to the
converter input pins is recommended.
5. It is recommended that a fuse be used on the input of
a power supply for protection. See the table above for
the correct rating.
Model Selection Guide
Notes:
All dimensions are typical in inches (mm)
Tolerance x.xx = 0.01 (0.25)
Pin 1 is marked by a "dot" or indentation on the side of the unit
Mechanical Dimensions
Pin Connections
Capacitive
Load
MicroPower Direct
www.micropowerdirect.com
232 Tosca Drive Stoughton, MA 02072
TEL: (781) 344-8226
FAX: (781) 344-8481
E-Mail: sales@micropowerdirect.com
Pin
Function
1
+Vin
2
NC
3
NC
9
NC
10
-Vout
11
+Vout
12
-Vin
NC: No Connection
F Max
470
Model
Number
Input
Output
Effi ciency
(%, Typ)
Fuse Rating
Slow-Blow
(mA)
Voltage (VDC)
Current (mA)
Voltage
(VDC)
Current
(mA, Max)
Current
(mA, Min)
Nominal
Range
Full-Load
No-Load
D201RP
5
4.5 - 5.5
606
80
5.0
400.0
40.0
66
1,000
D202RP
5
4.5 - 5.5
606
80
9.0
222.0
22.0
66
1,000
D203RP
5
4.5 - 5.5
571
80
12.0
167.0
17.0
70
1,000
D204RP
5
4.5 - 5.5
571
80
15.0
133.0
13.0
70
1,000
D205RP
5
4.5 - 5.5
588
80
24.0
83.0
10.0
68
1,000
D211RP
12
10.8 - 13.2
253
45
5.0
400.0
40.0
66
500
D212RP
12
10.8 - 13.2
253
45
9.0
222.0
22.0
66
500
D213RP
12
10.8 - 13.2
238
45
12.0
167.0
17.0
70
500
D214RP
12
10.8 - 13.2
238
45
15.0
133.0
13.0
70
500
D215RP
12
10.8 - 13.2
246
45
24.0
83.0
10.0
68
500
D221RP
24
21.6 - 26.4
130
25
5.0
400.0
40.0
64
200
D222RP
24
21.6 - 26.4
130
25
9.0
222.0
22.0
64
200
D223RP
24
21.6 - 26.4
122
25
12.0
167.0
17.0
68
200
D224RP
24
21.6 - 26.4
122
25
15.0
133.0
13.0
68
200
D225RP
24
21.6 - 26.4
118
25
24.0
83.0
10.0
70
200
Derating Curve