1/28

No Reproduction and Redistribution Allowed.

AU OPTRONICS CORPORATION

Product Specifications

15.0

XGA Color TFT-LCD Module

Model Name: M150XN07

V.1

Approved by

Prepared by

DDBU Marketing Division / AU Optronics Croporation

Customer

Checked & Approved by

Spec. No.: DDPM-M150XN07-0.1

Version: 1

Total pages: 26

Date: 2003-July-31

3/28

No Reproduction and Redistribution Allowed.

i Contents

1.0 Handling Precautions

2.0 General Description

2.1 Display Characteristics

2.2 Functional Block Diagram

3.0 Absolute Maximum Ratings

4.0 Optical Characteristics

4.1 Signal for Lamp connector

4.2 Parameter guideline for CCFL Inverter

5.0 Signal Interface

5.1 Module Interface Connectors

5.2 Module Connector Pin Configuration

5.3 Backlight Connectors

5.4 Backlight Connector Pin Configuration

5.5 Signal Electrical Characteristics

5.6 Interface Timings Characteristics

5.7 Interface Timing Definition

6.0 Pixel format image

7.0 Power Consumption

8.0 Power ON/OFF Sequence

9.0 Backlight Characteristics

9.1 Signal for Lamp connector

9.2 Parameter guideline for CCFL Inverter

10.0Vibration, Shock, and Drop

10.1 Vibration & Shock

10.1.1 Vibration Test Spec

10.1.2 Shock Test Spec

10.2 Drop

11.0 Environment

11.1 Temperature and Humidity

11.1.1 Operating Conditions

11.1.2 Shipping Conditions

11.2 Atmospheric Pressure

11.3 Thermal Shock

12.0 Reliability

12.1 Failure criteria

12.2 Failure rate

12.2.1 Usage

12.2.2 Components de-rating

12.3 CCFL life

12.4 ON/OFF cycle

4/28

No Reproduction and Redistribution Allowed.

13.0 Safety

13.1 Sharp edge requirement

13.2 Material

13.2.1 Toxicity

13.2.2 Flammability

13.3 Capacitors

13.4 Hazardous voltage

14.0 Other requirements

14.1 Smoke free design

14.2 National test lab requirement

15.0 Label

16.0 Mechanical Characteristics

ii Record of Revision

Version and Date Page

Old description

New Description

Remark

0.1 2003/06/10

All

First Edition for Customer

All

5/28

No Reproduction and Redistribution Allowed.

1.0 Handling Precautions

1) Since front polarizer is easily damaged, pay attention not to scratch it.
2) Be sure to turn off power supply when inserting or disconnecting from input connector.
3) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.
4) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.
5) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.
6) Since CMOS LSI is used in this module, take care of static electricity and insure human earth when

handling.

7) Do not open nor modify the Module Assembly.
8) Do not press the reflector sheet at the back of the module to any directions.
9) In case if a Module has to be put back into the packing container slot after once it was taken out from the

container, do not press the center of the CCFL Reflector edge. Instead, press at the far ends of the CFL
Reflector edge softly. Otherwise the TFT Module may be damaged.

10) At the insertion or removal of the Signal Interface Connector, be sure not to rotate nor tilt the Interface

Connector of the TFT Module.

11) After installation of the TFT Module into an enclosure (LCD monitor housing, for example), do not twist nor

bend the TFT Module even momentary. At designing the enclosure, it should be taken into consideration
that no bending/twisting forces are applied to the TFT Module from outside. Otherwise the TFT Module
may be damaged.

12) Cold cathode fluorescent lamp in LCD contains a small amount of mercury. Please follow local ordinances or

regulations for disposal.

13) Small amount of materials having no flammability grade is used in the LCD module. The LCD module should be

supplied by power complied with requirements of Limited Power Source (2.11, IEC60950 or UL1950), or be applied
exemption.

14) The LCD module is designed so that the CFL in it is supplied by Limited Current Circuit (2.4, IEC60950 or UL1950).

Do not connect the CFL in Hazardous Voltage Circuit.

Электронный компонент: M150XN07