1999 Fairchild Semiconductor Corporation
DS500311
www.fairchildsemi.com
August 1999
Revised October 1999
7
4
AC
T5
33 Oct
a
l
T
r
an
sparent
La
tch
w
i
t
h
3-
ST
A
T
E
Output
s
74ACT533
Octal Transparent Latch
with 3-STATE Outputs
General Description
The ACT533 consists of eight latches with 3-STATE out-
puts for bus organized system applications. The flip-flops
appear transparent to the data when Latch Enable (LE) is
HIGH. When LE is low, the data satisfying the input timing
requirements is latched. Data appears on the bus when the
Output Enable (OE) is LOW. When OE is HIGH, the bus
output is in the high impedance state.
Features
s
I
CC
and I
OZ
reduced by 50%
s
Eight latches in a single package
s
3-STATE outputs drive bus lines or buffer memory
address registers
s
Outputs source/sink 24 mA
s
Inverted version of the ACT373
s
TTL-compatible inputs
Ordering Code:
Device also available in Tape and Reel. Specify by appending suffix letter "X" to the ordering code
Logic Symbols
IEEE/IEC
Connection Diagram
Pin Descriptions
FACT
TM
is a trademark of Fairchild Semiconductor Corporation.
Order Number
Package Number
Package Description
74ACT533SC
M20B
20-Lead Small Outline Integrated Circuit (SOIC), JEDEC MS-013, 0.300" Wide Body
74ACT533MTC
MTC20
20-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
74ACT533PC
N20A
20-Lead Plastic Dual-In-Line Package (PDIP), JEDEC MS-001, 0.300" Wide
Pin Names
Description
D
0
D
7
Data Inputs
LE
Latch Enable Input
OE
Output Enable Input
O
0
O
7
3-STATE Latch Outputs
www.fairchildsemi.com
2
74ACT533
Functional Description
The ACT533 contains eight D-type latches with 3-STATE
standard outputs. When the Latch Enable (LE) input is
HIGH, data on the D
n
inputs enters the latches. In this con-
dition the latches are transparent, i.e., a latch output will
change state each time its D input changes. When LE is
LOW, the latches store the information that was present on
the D inputs at setup time preceding the HIGH-to-LOW
transition of LE. The 3-STATE standard outputs are con-
trolled by the Output Enable (OE) input. When OE is LOW,
the standard outputs are in the 2-state mode. When OE is
HIGH, the standard outputs are in the high impedance
mode but this does not interfere with entering new data into
the latches.
Truth Table
H
=
HIGH Voltage Level
L
=
LOW Voltage Level
Z
=
High Impedance
X
=
Immaterial
O
0
=
Previous O
0
before HIGH-to-LOW transition of Latch Enable
Logic Diagram
Please note that this diagram is provided only for the understanding of logic operations and should not be used to estimate propagation delays.
Inputs
Outputs
LE
OE
D
n
O
n
X
H
X
Z
H
L
L
H
H
L
H
L
L
L
X
O
0
3
www.fairchildsemi.com
7
4
AC
T5
33
Absolute Maximum Ratings
(Note 1)
Recommended Operating
Conditions
Note 1: Absolute maximum ratings are those values beyond which damage
to the device may occur. The databook specifications should be met, with-
out exception, to ensure that the system design is reliable over its power
supply, temperature, and output/input loading variables. Fairchild does not
recommend operation of FACT
TM
circuits outside databook specifications.
DC Electrical Characteristics
Note 2: All outputs loaded; thresholds on input associated with output under test.
Note 3: Maximum test duration 2.0 ms, one output loaded at a time.
Supply Voltage (V
CC
)
-
0.5V to
+
7.0V
DC Input Diode Current (I
IK
)
V
I
=
-
0.5V
-
20 mA
V
I
=
V
CC
+
0.5V
+
20 mA
DC Input Voltage (V
I
)
-
0.5V to V
CC
+
0.5V
DC Output Diode Current (I
OK
)
V
O
=
-
0.5V
-
20 mA
V
O
=
V
CC
+
0.5V
+
20 mA
DC Output Voltage (V
O
)
-
0.5V to V
CC
+
0.5V
DC Output Source
or Sink Current (I
O
)
50 mA
DC V
CC
or Ground Current
per Output Pin (I
CC
or I
GND
)
50 mA
Storage Temperature (T
STG
)
-
65
C to
+
150
C
DC Latchup Source
or
Sink
Current
300 mA
Junction Temperature (T
J
)
PDIP
140
C
Supply Voltage (V
CC
)
4.5V to 5.5V
Input Voltage (V
I
)
0V to V
CC
Output Voltage (V
O
)
0V to V
CC
Operating Temperature (T
A
)
-
40
C to
+
85
C
Minimum Input Edge Rate
V/
t
V
IN
from 0.8V to 2.0V
V
CC
@ 4.5V, 5.5V
125 mV/ns
Symbol
Parameter
V
CC
T
A
=
+
25
C
T
A
=
-
40
C to
+
85
C
Units
Conditions
(V)
Typ
Guaranteed Limits
V
IH
Minimum HIGH Level
4.5
1.5
2.0
2.0
V
V
OUT
=
0.1V
Input Voltage
5.5
1.5
2.0
2.0
or V
CC
-
0.1V
V
IL
Maximum LOW Level
4.5
1.5
0.8
0.8
V
V
OUT
=
0.1V
Input Voltage
5.5
1.5
0.8
0.8
or V
CC
-
0.1V
V
OH
Minimum HIGH Level
4.5
4.49
4.4
4.4
V
I
OUT
=
-
50
A
Output Voltage
5.5
5.49
5.4
5.4
V
IN
=
V
IL
or V
IH
4.5
3.86
3.76
V
I
OH
=
-
24 mA
5.5
4.86
4.76
I
OH
=
-
24 mA (Note 2)
V
OL
Maximum LOW Level
4.5
0.001
0.1
0.1
V
I
OUT
=
50
A
Output Voltage
5.5
0.001
0.1
0.1
V
IN
=
V
IL
or V
IH
4.5
0.36
0.44
V
I
OL
=
24 mA
5.5
0.36
0.44
I
OL
=
24 mA (Note 2)
I
IN
Maximum Input
5.5
0.1
1.0
A
V
I
=
V
CC
, GND
Leakage Current
I
OZ
Maximum 3-STATE
5.5
0.25
2.5
A
V
I
=
V
IL
, V
IH
Leakage Current
V
O
=
V
CC
, GND
I
CCT
Maximum
5.5
0.6
1.5
mA
V
I
=
V
CC
-
2.1V
I
CC
/Input
I
OLD
Minimum Dynamic
5.5
75
mA
V
OLD
=
1.65V Max
I
OHD
Output Current (Note 3)
5.5
-
75
mA
V
OHD
=
3.85V Min
I
CC
Maximum Quiescent
5.5
4.0
40.0
A
V
IN
=
V
CC
Supply Current
or GND
www.fairchildsemi.com
4
74ACT533
AC Electrical Characteristics
Note 4: Voltage Range 5.0 is 5.0V
0.5V.
AC Operating Requirements
Note 5: Voltage Range 5.0 is 5.0V
0.5V.
Capacitance
Symbol
Parameter
V
CC
T
A
=
+
25
C
T
A
=
-
40
C to
+
85
C
Units
(V)
C
L
=
50 pF
C
L
=
50 pF
(Note 4)
Min
Typ
Max
Min
Max
t
PHL
Propagation Delay
5.0
2.0
6.0
8.0
2.0
8.5
ns
t
PLH
D
n
to O
n
t
PHL
Propagation Delay
5.0
2.5
7.0
9.0
2.5
9.5
ns
t
PLH
LE to O
n
t
PZL
, t
PZH
Output Enable Time
5.0
2.0
7.0
9.0
2.0
9.5
ns
t
PHZ
, t
PLZ
Output Disable Time
5.0
1.0
8.0
10.0
1.0
10.5
ns
Symbol
Parameter
V
CC
T
A
=
+
25
C
T
A
=
-
40
C to
+
85
C
Units
(V)
C
L
=
50 pF
C
L
=
50 pF
(Note 5)
Typ
Guaranteed Minimum
t
S
Setup Time, HIGH or LOW
5.0
0
3.0
3.0
ns
D
n
to LE
t
H
Hold Time, HIGH or LOW
5.0
0
1.5
1.5
ns
D
n
to LE
t
W
LE Pulse Width, HIGH
5.0
2.0
4.0
4.0
ns
Symbol
Parameter
Typ
Units
Conditions
C
IN
Input Capacitance
4.5
pF
V
CC
=
OPEN
C
PD
Power Dissipation Capacitance
40
pF
V
CC
=
5.0V
5
www.fairchildsemi.com
7
4
AC
T5
33
Physical Dimensions
inches (millimeters) unless otherwise noted
20-Lead Small Outline Integrated Circuit, JEDEC MS-013, 0.300" Wide Body
Package Number M20B
www.fairchildsemi.com
6
74ACT533
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
20-Lead Thin Shrink Small Outline Package (TSSOP), JEDEC MO-153, 4.4mm Wide
Package Number MTC20
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
7
www.fairchildsemi.com
7
4
AC
T5
33 Oct
a
l
T
r
an
sparent
La
tch
w
i
t
h
3-
ST
A
T
E
Output
s
Physical Dimensions
inches (millimeters) unless otherwise noted (Continued)
20-Lead Plastic Dual-In-Line Package, JEDEC MS-001, 0.300" Wide
Package Number N20A
Fairchild does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and
Fairchild reserves the right at any time without notice to change said circuitry and specifications.
LIFE SUPPORT POLICY
FAIRCHILD'S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT OF FAIRCHILD
SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or systems
which, (a) are intended for surgical implant into the
body, or (b) support or sustain life, and (c) whose failure
to perform when properly used in accordance with
instructions for use provided in the labeling, can be rea-
sonably expected to result in a significant injury to the
user.
2. A critical component in any component of a life support
device or system whose failure to perform can be rea-
sonably expected to cause the failure of the life support
device or system, or to affect its safety or effectiveness.
www.fairchildsemi.com
PDF 
ZIP