INDUSTRIAL TEMPERATURE RANGE
IDT74ALVCH16835
3.3V CMOS 18-BIT UNIVERSAL BUS DRIVER WITH 3-STATE OUTPUTS
1
MARCH 1999
INDUSTRIAL TEMPERATURE RANGE
The IDT logo is a registered trademark of Integrated Device Technology, Inc.
1999 Integrated Device Technology, Inc.
DSC-4570/2
FEATURES:
0.5 MICRON CMOS Technology
Typical t
SK(o)
(Output Skew) < 250ps
ESD > 2000V per MIL-STD-883, Method 3015; > 200V using
machine model (C = 200pF, R = 0)
V
CC
= 3.3V 0.3V, Normal Range
V
CC
= 2.7V to 3.6V, Extended Range
V
CC
= 2.5V 0.2V
CMOS power levels (0.4
W typ. static)
Rail-to-Rail output swing for increased noise margin
Available in SSOP, TSSOP, and TVSOP packages
FUNCTIONAL BLOCK DIAGRAM
IDT74ALVCH16835
3.3V CMOS 18-BIT
UNIVERSAL BUS DRIVER
WITH 3-STATE OUTPUTS
AND BUS-HOLD
DESCRIPTION:
This 18-bit universal bus driver is built using advanced dual metal CMOS
technology. Data flow from A to Y is controlled by the output-enable (OE)
input. The device operates in the transparent mode when the latch-enable
(LE) input is high. The A data is latched if the clock (CLK) input is held at a
high or low logic level. If LE is low, the A data is stored in the latch flip-flop
on the low-to-high transition of CLK. When OE is high, the outputs are in the
high-impedance state.
The ALVCH16835 has been designed with a 24mA output driver. This
driver is capable of driving a moderate to heavy load while maintaining
speed performance.
The ALVCH16835 has "bus-hold" which retains the inputs' last state
whenever the input bus goes to a high-impedance. This prevents floating
inputs and eliminates the need for pull-up/down resistors.
APPLICATIONS:
SDRAM Modules
PC Motherboards
Workstations
DRIVE FEATURES:
High Output Drivers: 24mA
Suitable for heavy loads
LE
A
1
TO 17 OTHER CHANNELS
OE
CLK
27
54
28
30
1
D
CLK
3
Y
1
C
1
INDUSTRIAL TEMPERATURE RANGE
2
IDT74ALVCH16835
3.3V CMOS 18-BIT UNIVERSAL BUS DRIVER WITH 3-STATE OUTPUTS
SSOP/ TSSOP/ TVSOP
TOP VIEW
PIN CONFIGURATION
Symbol
Description
Max
Unit
V
TERM
(2)
Terminal Voltage with Respect to GND
0.5 to +4.6
V
V
TERM
(3)
Terminal Voltage with Respect to GND
0.5 to V
CC
+0.5
V
T
STG
Storage Temperature
65 to +150
C
I
OUT
DC Output Current
50 to +50
mA
I
IK
Continuous Clamp Current,
50
mA
V
I
< 0 or V
I
> V
CC
I
OK
Continuous Clamp Current, V
O
< 0
50
mA
I
CC
Continuous Current through each
100
mA
I
SS
V
CC
or GND
ABSOLUTE MAXIMUM RATINGS
(1)
NOTES:
1. Stresses greater than those listed under ABSOLUTE MAXIMUM RATINGS may cause
permanent damage to the device. This is a stress rating only and functional operation
of the device at these or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect reliability.
2. V
CC
terminals.
3. All terminals except V
CC
.
NOTE:
1. As applicable to the device type.
Symbol
Parameter
(1)
Conditions
Typ.
Max.
Unit
C
IN
Input Capacitance
V
IN
= 0V
5
7
pF
C
OUT
Output Capacitance
V
OUT
= 0V
7
9
pF
C
OUT
I/O Port Capacitance
V
IN
= 0V
7
9
pF
CAPACITANCE
(T
A
= +25C, F = 1.0MHz)
Pin Names
Description
OE
3-State Output Enable Input (Active LOW)
CLK
Register Clock Input
LE
Latch Enable Input (Transparent HIGH)
A x
Data Inputs
(1)
Y x
3-State Outputs
PIN DESCRIPTION
NOTE:
1. These pins have "Bus-Hold". All other pins are standard inputs, outputs, or I/Os.
FUNCTION TABLE
(1)
NOTES:
1. H = HIGH Voltage Level
L = LOW Voltage Level
X = Don't Care
= LOW-to-HIGH Transition
Z = High-Impedance
2. Output level before the indicated steady-state input conditions were established,
provided that CLK is HIGH before LE went LOW.
3. Output level before the indicated steady-state input conditions were established.
Inputs
Output
OE
LE
CLK
Ax
Yx
H
X
X
X
Z
L
H
X
L
L
L
H
X
H
H
L
L
L
L
L
L
H
H
L
L
H
X
Y
(2)
L
L
L
X
Y
(3)
GND
GND
GND
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
48
49
50
51
52
53
54
55
56
1
GND
GND
GND
25
26
27
28
32
31
30
29
GND
NC
A
1
NC
NC
Y
1
Y
2
Y
3
Y
4
Y
5
Y
6
Y
7
Y
8
Y
9
Y
10
Y
11
Y
12
Y
13
Y
14
Y
15
Y
16
Y
17
Y
18
A
2
A
3
A
4
A
5
A
6
A
7
A
8
A
9
A
10
A
11
A
12
A
13
A
14
A
15
V
CC
A
16
A
17
A
18
GND
V
CC
CLK
GND
V
CC
V
CC
GND
OE
LE
INDUSTRIAL TEMPERATURE RANGE
IDT74ALVCH16835
3.3V CMOS 18-BIT UNIVERSAL BUS DRIVER WITH 3-STATE OUTPUTS
3
Symbol
Parameter
Test Conditions
Min.
Typ.
(1)
Max.
Unit
V
IH
Input HIGH Voltage Level
V
CC
= 2.3V to 2.7V
1.7
--
--
V
V
CC
= 2.7V to 3.6V
2
--
--
V
IL
Input LOW Voltage Level
V
CC
= 2.3V to 2.7V
--
--
0.7
V
V
CC
= 2.7V to 3.6V
--
--
0.8
I
IH
Input HIGH Current
V
CC
= 3.6V
V
I
= V
CC
--
--
5
A
I
IL
Input LOW Current
V
CC
= 3.6V
V
I
= GND
--
--
5
A
I
OZH
High Impedance Output Current
V
CC
= 3.6V
V
O
= V
CC
--
--
10
A
I
OZL
(3-State Output pins)
V
O
= GND
--
--
10
V
IK
Clamp Diode Voltage
V
CC
= 2.3V, I
IN
= 18mA
--
0.7
1.2
V
V
H
Input Hysteresis
V
CC
= 3.3V
--
100
--
mV
I
CCL
Quiescent Power Supply Current
V
CC
= 3.6V
--
0.1
40
A
I
CCH
V
IN
= GND or V
CC
I
CCZ
I
CC
Quiescent Power Supply Current
One input at V
CC
- 0.6V, other inputs at V
CC
or GND
--
--
750
A
Variation
DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE
Following Conditions Apply Unless Otherwise Specified:
Operating Condition: T
A
= 40C to +85C
NOTE:
1. Typical values are at V
CC
= 3.3V, +25C ambient.
BUS-HOLD CHARACTERISTICS
Symbol
Parameter
(1)
Test Conditions
Min.
Typ.
(2)
Max.
Unit
I
BHH
Bus-Hold Input Sustain Current
V
CC
= 3V
V
I
= 2V
75
--
--
A
I
BHL
V
I
= 0.8V
75
--
--
I
BHH
Bus-Hold Input Sustain Current
V
CC
= 2.3V
V
I
= 1.7V
45
--
--
A
I
BHL
V
I
= 0.7V
45
--
--
I
BHHO
Bus-Hold Input Overdrive Current
V
CC
= 3.6V
V
I
= 0 to 3.6V
--
--
500
A
I
BHLO
NOTES:
1. Pins with Bus-Hold are identified in the pin description.
2. Typical values are at V
CC
= 3.3V, +25C ambient.
INDUSTRIAL TEMPERATURE RANGE
4
IDT74ALVCH16835
3.3V CMOS 18-BIT UNIVERSAL BUS DRIVER WITH 3-STATE OUTPUTS
OPERATING CHARACTERISTICS, T
A
= 25C
V
CC
= 2.5V 0.2V
V
CC
= 3.3V 0.3V
Symbol
Parameter
Test Conditions
Typical
Typical
Unit
C
PD
Power Dissipation Capacitance Outputs enabled
C
L
= 0pF, f = 10Mhz
26
31
pF
C
PD
Power Dissipation Capacitance Outputs disabled
12
14
NOTE:
1. V
IH
and V
IL
must be within the min. or max. range shown in the DC ELECTRICAL CHARACTERISTICS OVER OPERATING RANGE table for the appropriate V
CC
range.
T
A
= 40C to + 85C.
OUTPUT DRIVE CHARACTERISTICS
Symbol
Parameter
Test Conditions
(1)
Min.
Max.
Unit
V
OH
Output HIGH Voltage
V
CC
= 2.3V to 3.6V
I
OH
= 0.1mA
V
CC
0.2
--
V
V
CC
= 2.3V
I
OH
= 6mA
2
--
V
CC
= 2.3V
I
OH
= 12mA
1.7
--
V
CC
= 2.7V
2.2
--
V
CC
= 3V
2.4
--
V
CC
= 3V
I
OH
= 24mA
2
--
V
OL
Output LOW Voltage
V
CC
= 2.3V to 3.6V
I
OL
= 0.1mA
--
0.2
V
V
CC
= 2.3V
I
OL
= 6mA
--
0.4
I
OL
= 12mA
--
0.7
V
CC
= 2.7V
I
OL
= 12mA
--
0.4
V
CC
= 3V
I
OL
= 24mA
--
0.55
INDUSTRIAL TEMPERATURE RANGE
IDT74ALVCH16835
3.3V CMOS 18-BIT UNIVERSAL BUS DRIVER WITH 3-STATE OUTPUTS
5
NOTES:
1. See TEST CIRCUITS AND WAVEFORMS. T
A
= 40C to + 85C.
2
Skew between any two outputs of the same package and switching in the same direction.
SWITCHING CHARACTERISTICS
(1)
V
CC
= 2.5V 0.2V
V
CC
= 2.7V
V
CC
= 3.3V 0.3V
Symbol
Parameter
Min.
Max.
Min.
Max.
Min.
Max.
Unit
f
MAX
150
--
150
--
150
--
ns
t
PLH
Propagation Delay
1
4.2
--
4.2
1
3.6
ns
t
PHL
Ax to Yx
t
PLH
Propagation Delay
1.3
5
--
4.9
1.3
4.2
ns
t
PHL
LE to Yx
t
PLH
Propagation Delay
1.4
5.5
--
5.2
1.4
4.5
ns
t
PHL
CLK to Yx
t
PZH
Output Enable Time
1.4
5.5
--
5.6
1.1
4.6
ns
t
PZL
OE to Yx
t
PHZ
Output Disable Time
1
4.5
--
4.3
1.3
3.9
ns
t
PLZ
OE to Yx
t
SU
Set-up Time, data before CLK
2.2
--
2.1
--
1.7
--
ns
t
SU
Set-up Time, data before LE
, CLK HIGH
1.9
--
1.6
--
1.5
--
ns
t
SU
Set-up Time, data before LE
, CLK LOW
1.3
--
1.1
--
1
--
ns
t
H
Hold Time, data after CLK
0.6
--
0.6
--
0.7
--
ns
t
H
Hold Time, data after LE
, CLK HIGH or LOW
1.4
--
1.7
--
1.4
--
ns
t
W
Pulse Duration, LE HIGH
3.3
--
3.3
--
3.3
--
ns
t
W
Pulse Duration, CLK HIGH or LOW
3.3
--
3.3
--
3.3
--
ns
t
SK(O)
Output Skew
(2)
--
--
--
--
--
500
ps
SWITCHING CHARACTERISTICS FROM 0C TO 65C, C
L
= 50pF
V
CC
= 3.3V 0.15V
Symbol
Parameter
Min.
Max.
Unit
t
PLH
Propagation Delay
1.7
4.5
ns
t
PHL
CLK to Yx
INDUSTRIAL TEMPERATURE RANGE
6
IDT74ALVCH16835
3.3V CMOS 18-BIT UNIVERSAL BUS DRIVER WITH 3-STATE OUTPUTS
Open
V
LOAD
GND
V
CC
Pulse
Generator
D.U.T.
500
500
C
L
R
T
V
IN
V
OUT
(1, 2)
ALVC Link
INPUT
V
IH
0V
V
OH
V
OL
t
PLH1
t
SK
(x)
OUTPUT 1
OUTPUT 2
t
PHL1
t
SK
(x)
t
PLH2
t
PHL2
V
T
V
T
V
OH
V
T
V
OL
t
SK
(x)
= t
PLH2
-
t
PLH1
or
t
PHL2
-
t
PHL1
ALVC Link
SAME PHASE
INPUT TRANSITION
OPPOSITE PHASE
INPUT TRANSITION
0V
0V
V
OH
V
OL
t
PLH
t
PHL
t
PHL
t
PLH
OUTPUT
V
IH
V
T
V
T
V
IH
V
T
ALVC Link
DATA
INPUT
0V
0V
0V
0V
t
REM
TIMING
INPUT
SYNCHRONOUS
CONTROL
t
SU
t
H
t
SU
t
H
V
IH
V
T
V
IH
V
T
V
IH
V
T
V
IH
V
T
ALVC Link
ASYNCHRONOUS
CONTROL
LOW-HIGH-LOW
PULSE
HIGH-LOW-HIGH
PULSE
V
T
t
W
V
T
ALVC Link
CONTROL
INPUT
t
PLZ
0V
OUTPUT
NORMALLY
LOW
t
PZH
0V
SWITCH
CLOSED
OUTPUT
NORMALLY
HIGH
ENABLE
DISABLE
SWITCH
OPEN
t
PHZ
0V
V
LZ
V
OH
V
T
V
T
t
PZL
V
LOAD/2
V
LOAD/2
V
IH
V
T
V
OL
V
HZ
ALVC Link
TEST CIRCUITS AND WAVEFORMS
Propagation Delay
Test Circuit for All Outputs
Enable and Disable Times
Set-up, Hold, and Release Times
NOTES:
1. For t
SK
(o) OUTPUT1 and OUTPUT2 are any two outputs.
2. For t
SK
(b) OUTPUT1 and OUTPUT2 are in the same bank.
DEFINITIONS:
C
L
= Load capacitance: includes jig and probe capacitance.
R
T
= Termination resistance: should be equal to Z
OUT
of the Pulse Generator.
NOTES:
1. Pulse Generator for All Pulses: Rate
1.0MHz; t
F
2.5ns; t
R
2.5ns.
2. Pulse Generator for All Pulses: Rate
1.0MHz; t
F
2ns; t
R
2ns.
Output Skew - t
SK
(
X
)
Pulse Width
NOTE:
1. Diagram shown for input Control Enable-LOW and input Control Disable-HIGH.
Symbol V
CC(1)
= 3.3V0.3V V
CC(1)
= 2.7V
V
CC(2)
= 2.5V0.2V
Unit
V
LOAD
6
6
2 x Vcc
V
V
IH
2.7
2.7
Vcc
V
V
T
1.5
1.5
Vcc
/ 2
V
V
LZ
300
300
150
mV
V
HZ
300
300
150
mV
C
L
50
50
30
pF
TEST CONDITIONS
SWITCH POSITION
Test
Switch
Open Drain
Disable Low
V
LOAD
Enable Low
Disable High
GND
Enable High
All Other Tests
Open
INDUSTRIAL TEMPERATURE RANGE
IDT74ALVCH16835
3.3V CMOS 18-BIT UNIVERSAL BUS DRIVER WITH 3-STATE OUTPUTS
7
ORDERING INFORMATION
CORPORATE HEADQUARTERS
for SALES:
for Tech Support:
2975 Stender Way
800-345-7015 or 408-727-6116
logichelp@idt.com
Santa Clara, CA 95054
fax: 408-492-8674
(408) 654-6459
www.idt.com
IDT
XX
ALVC
XXX
XX
Package
Device Type
Temp. Range
PV
PA
PF
16
74
Shrink Small Outline Package
Thin Shrink Small Outline Package
Thin Very Small Outline Package
18-Bit Universal Bus Driver with 3-State Outputs
40C to +85C
X
XXX
Family
Bus-Hold
835
Double-Density, 24mA
Bus-Hold
H
PDF 
ZIP