ChipFind - документация

Электронный компонент: IL072N

Скачать:  PDF   ZIP

Document Outline

TECHNICAL DATA
IL072
Low Power J-FET DUAL
OPERATIONAL AMPLIFIERS
ORDERING INFORMATION
IL072N Plastic
IL072D SOIC
T
A
= -40
to 85 C for package
The IL072 are high speed J-FET input dual operational amplifiers
incorporating well matched, high voltage J-FET and bipolar transistors
in a monolithic integrated circuit.
The devices feature high slew rates, low input bias and offset current,
and low offset voltage temperature coefficient.

Low power consumption
Wide common-mode and differential voltage range
Low input bias and offset currents
Low noise e
n
=18 nV/
Hz (typ)
Output short-circuit protection
High input impedance J-FET input stage
Low harmonic distortion: 0.01% (typ)
Internal frequency compensation
Latch up free operation
High slew rate: 13 V/
s (typ)





Pin Connections (top view)


1 - Output
1
2
-
Inverting input 1
3
-
Non-inverting input 1
4 - V
CC
-
5
-
Non-inverting input 2
6
-
Inverting input 2
7 - Output
2
8 - V
CC
+





IL072


SCHEMATIC DIAGRAM

V
C
+
Non-inverting
inpu
Inverting
inpu
V
C
_
100
100
Output
1/4 IL072
200




MAXIMUM RATING
Symbol Parameter
IL072
Unit
V
CC
Supply Voltage - (note 1)
18
V
V
i
Input Voltage - (note 3)
15
V
V
id
Differential Input Voltage - (note 2)
30
V
P
tot
Power Dissipation
680
mW
Output Short-Circuit Duration (Note 4)
Infinite
T
oper
Operating Free-Air Temperature Range
-40 to 85
0
C
T
stg
Storage Temperature Range
-65 to +150
0
C
Notes
.
1.
All voltage values, except differential voltage, are with respect to the zero reference level (ground) of the supply
voltages where the zero reference level is the midpoint between V
CC
+
and V
CC
-
.
2.
Differential voltages are at the non-inverting input terminal with respect to the inverting input terminal.
3.
The magnitude of the input voltage must never exceed the magnitude of the supply voltage or 15 volts, whichever is
less.
4.
The output may be shorted to ground or to either supply. Temperature and/or supply voltages must be limited to
ensure that the dissipation rating is not exceeded.




IL072


ELECTRICAL CHARACTERISTICS
V
CC
=
15V, T
AMB
= 25
C (unless otherwise specified)
IL072
Symbol ParametersI
Min.
Typ. Max.
Unit
V
IO
Input Offset Voltage (R
S
= 50
, V
0
=0)
T
amb
=25
C
T
min.
T
amb.
T
max.
3
10
13
mV
DV
IO
Input Offset Voltage Drift
18
V/C
I
IO
Input Offset Current*
T
amb
=25
C
T
min.
T
amb.
T
max.
5
100
10
pA
nA
I
IB
Input Bias Current*
T
amb
=25
C
T
min.
T
amb.
T
max.
65
200
20
pA
nA
A
VD
Large Signal Voltage Gain (R
L
= 2k
, V
O
=
10V)
T
amb
=25
C
T
min.
T
amb.
T
max.
25
15
200
V/mV
SVR
Supply Voltage Rejection Ratio (R
S
= 50
, V
0
=0)
T
amb
=25
C
T
min.
T
amb.
T
max.
70
70
86
dB
I
CC
Supply Current (Per Amplifier)
T
amb
=25
C
T
min.
T
amb.
T
max
1.4
2.5
2.5
mA
V
ICM
Input Common Mode Voltage Range
11
+15
-12
V
CMR
Common Mode Rejection Ratio (R
S
= 50
, V
0
=0)
T
amb
=25
C
70 86
dB
V
OPP
Output Voltage Swing
T
amb
=25
C R
L
=10k
T
min.
T
amb.
T
max.
R
L
=2k
R
L
=10k
12
10
12
13.5
V
SR
Slew Rate (V
i
= 10V, R
L
= 2k
, C
L
= 100pF,
T
amb
=25
C, unity gain)
8 13 V/
s
t
r
Rise Time (V
i
= 20mV, R
L
= 2k
, C
L
=100pF,
T
amb
=25
C, unity gain)
0.1
s
K
OV
Overshoot (V
i
= 20mV, R
L
= 2k
, C
L
=100pF,
T
amb
=25
C, unity gain)
20 %
GBP
Gain Bandwidth Product
3
MHz
R
I
Input Resistance
10
12
THD
Total Harmonic Distortion (f=1kHz, R
L
= 2k
,
T
amb
=25
C)
0.01
%
e
n
Equivalent input Noise Voltage
(R
S
= 100
, f = 1KHz)
18
nV
Hz
V
O1
/V
O2
Channel Separation (A
V
=100)
120
dB
* The Input bias currents are junction leakage currents which approximately double for every 10
0
C increase in the junction
temperature.




IL072

IL072