TECHNICAL DATA
507
Analog Multiplexer/Demultiplexer
High-Performance Silicon-Gate CMOS
The IN74HC4053 utilize silicon-gate CMOS technology to achieve
fast propagation delays, low ON resistances, and low OFF leakage
currents. These analog multiplexers/demultiplexers control analog
voltages that may vary across the complete power supply range (from
V
CC
to V
EE
).
The Channel-Select inputs determine which one of the Analog
Inputs/Outputs is to be connected, by means of an analog switch, to the
Common Output/Input.When the Enable pin is high, all analog
switches are turned off.
The Channel-Select and Enable inputs are compatible with
standard CMOS outputs; with pullup resistors, they are compatible
with LS/ALSTTL outputs.
Fast Switching and Propagation Speeds
Low Crosstalk Between Switches
Diode Protection on All Inputs/Outputs
Analog Power Supply Range (V
CC
-V
EE
)=2.0 to 12.0 V
Digital (Control) Power Supply Range (V
CC
-GND)=2.0 to 6.0 V
Low Noise
IN74HC4053
ORDERING INFORMATION
IN74HC4053N Plastic
IN74HC4053DW SOIC
T
A
= -55
to 125
C for all packages
PIN ASSIGNMENT
FUNCTION TABLE
Control Inputs
ON
Enable
Select
Channels
C
B
A
L
L
L
L
Z0
Y0
X0
L
L
L
H
Z0
Y0
X1
L
L
H
L
Z0
Y1
X0
L
L
H
H
Z0
Y1
X1
L
H
L
L
Z1
Y0
X0
L
H
L
H
Z1
Y0
X1
L
H
H
L
Z1
Y1
X0
L
H
H
H
Z1
Y1
X1
H
X
X
X
None
X = don't care
LOGIC DIAGRAM
Triple Single-Pole, Double-Position
Plus Common Off
PIN 16 =V
CC
PIN 7 = V
EE
PIN 8 = GND
IN74HC4053
508
MAXIMUM RATINGS
*
Symbol
Parameter
Value
Unit
V
CC
Positive DC Supply Voltage (Referenced to GND)
(Referenced to V
EE
)
-0.5 to +7.0
-0.5 to +14.0
V
V
EE
Negative DC Supply Voltage (Referenced to GND)
-7.0 to +0.5
V
V
IS
Analog Input Voltage
V
EE
- 0.5 to V
CC
+0.5
V
V
IN
Digital Input Voltage (Referenced to GND)
-1.5 to V
CC
+1.5
V
I
DC Input Current Into or Out of Any Pin
25
mA
P
D
Power Dissipation in Still Air, Plastic DIP+
SOIC Package+
750
500
mW
Tstg
Storage Temperature
-65 to +150
C
T
L
Lead Temperature, 1 mm from Case for 10 Seconds
(Plastic DIP or SOIC Package)
260
C
*
Maximum Ratings are those values beyond which damage to the device may occur.
Functional operation should be restricted to the Recommended Operating Conditions.
+Derating - Plastic DIP: - 10 mW/
C from 65
to 125
C
SOIC Package: : - 7 mW/
C from 65
to 125
C
RECOMMENDED OPERATING CONDITIONS
Symbol
Parameter
Min
Max
Unit
V
CC
Positive Supply Voltage (Referenced to GND)
(Referenced to V
EE
)
2.0
2.0
6.0
12.0
V
V
EE
Negative DC Supply Voltage (Referenced to GND)
- 6.0
GND
V
V
IS
Analog Input Voltage
V
EE
V
CC
V
V
IN
Digital Input Voltage (Referenced to GND)
GND
V
CC
V
V
IO
*
Static or Dynamic Voltage Across Switch
-
1.2
V
T
A
Operating Temperature, All Package Types
-55
+125
C
t
r
, t
f
Input Rise and Fall Time (Channel Select
or Enable Inputs)
V
CC
=2.0 V
V
CC
=4.5 V
V
CC
=6.0 V
0
0
0
1000
500
400
ns
*
For voltage drops across the switch greater than 1.2 V (switch on), excessive V
CC
current may be drawn;
i. e., the current out of the switch may contain both V
CC
and switch input components. The reliability of the
device will be unaffected unless the Maximum Ratings are exceeded.
This device contains protection circuitry to guard against damage due to high static voltages or electric
fields. However, precautions must be taken to avoid applications of any voltage higher than maximum rated
voltages to this high-impedance circuit. For proper operation, V
IN
and V
OUT
should be constrained to the range
indicated in the Recommended Operating Conditions..
Unused digital input pins must always be tied to an appropriate logic voltage level (e.g., either GND or
V
CC
). Unused Analog I/O pins may be left open or terminated.
IN74HC4053
509
DC ELECTRICAL CHARACTERISTICS
Digital Section
(Voltages Referenced to GND)
V
EE
=GND, Except Where Noted
V
CC
Guaranteed Limit
Symbol
Parameter
Test Conditions
V
25
C
to
-55
C
85
C
125
C
Unit
V
IH
Minimum High-Level
Input Voltage,
Channel-Select or
Enable Inputs
R
ON
= Per Spec
2.0
4.5
6.0
1.5
3.15
4.2
1.5
3.15
4.2
1.5
3.15
4.2
V
V
IL
Maximum Low -Level
Input Voltage,
Channel-Select or
Enable Inputs
R
ON
= Per Spec
2.0
4.5
6.0
0.3
0.9
1.2
0.3
0.9
1.2
0.3
0.9
1.2
V
I
IN
Maximum Input
Leakage Current,
Channel-Select or
Enable Inputs
V
IN
=V
CC
or GND,
V
EE
=-6.0 V
6.0
0.1
1.0
1.0
A
I
CC
Maximum Quiescent
Supply Current
(per Package)
Channel Select = V
CC
or GND
Enable = V
CC
or GND
V
IS
= V
CC
or GND
V
IO
= 0 V V
EE
= GND
V
EE
= -6.0
6.0
6.0
2
8
20
80
40
160
A
DC ELECTRICAL CHARACTERISTICS
Analog Section
V
CC
V
EE
Guaranteed Limit
Symbol
Parameter
Test Conditions
V
V
25
C
to
-55
C
85
C
125
C
Uni
t
R
ON
Maximum "ON" Resistance
V
IN
=V
IL
or V
IH
V
IS
= V
CC
or V
EE
I
S
2.0 mA(Figure 1)
4.5
4.5
6.0
0.0
-4.5
-6.0
190
120
100
240
150
125
280
170
140
V
IN
=V
IL
or V
IH
V
IS
= V
CC
or V
EE
(Endpoints)
I
S
2.0 mA(Figure 1)
4.5
4.5
6.0
0.0
-4.5
-6.0
150
100
80
190
125
100
230
140
115
R
ON
Maximum Difference in
"ON" Resistance Between
Any Two Channels in the
Same Package
V
IN
=V
IL
or V
IH
V
IS
= 1/2 (V
CC
- V
EE
)
I
S
2.0 mA
4.5
4.5
6.0
0.0
-4.5
-6.0
30
12
10
35
15
12
40
18
14
I
OFF
Maximum Off- Channel
Leakage Current, Any One
Channel
V
IN
=V
IL
or V
IH
V
IO
= V
CC
- V
EE
Switch Off (Figure 2)
6.0
-6.0
0.1
0.5
1.0
A
Maximum Off- Channel
Leakage Current, Common
Channel
V
IN
=V
IL
or V
IH
V
IO
= V
CC
- V
EE
Switch Off (Figure 3)
6.0
-6.0
0.1
1.0
2.0
I
ON
Maximum On- Channel
Leakage Current, Channel to
Channel
V
IN
=V
IL
or V
IH
Switch to Switch =
V
CC
- V
EE
(Figure 5)
6.0
-6.0
0.1
1.0
2.0
A
IN74HC4053
510
AC ELECTRICAL CHARACTERISTICS
(C
L
=50pF,Input t
r
=t
f
=6.0 ns)
V
CC
Guaranteed Limit
Symbol
Parameter
V
25
C
to
-55
C
85
C
125
C
Unit
t
PLH
, t
PHL
Maximum Propagation Delay, Channel-Select to
Analog Output (Figures 8 and 9)
2.0
4.5
6.0
370
74
63
465
93
79
550
110
94
ns
t
PLH
, t
PHL
Maximum Propagation Delay , Analog Input to
Analog Output (Figures 10 and 11)
2.0
4.5
6.0
60
12
10
75
15
13
90
18
15
ns
t
PLZ
, t
PHZ
Maximum Propagation Delay , Enable to Analog
Output (Figures 12 and 13)
2.0
4.5
6.0
290
58
49
364
73
62
430
86
73
ns
t
PZL
, t
PZH
Maximum Propagation Delay , Enable to Analog
Output (Figures 12 and 13)
2.0
4.5
6.0
345
69
59
435
87
74
515
103
87
ns
C
IN
Maximum Input Capacitance, Channel-Select or
Enable Inputs
-
10
10
10
pF
C
I/O
Maximum Capacitance
Analog I/O
All Switches Off
-
35
35
35
pF
Common O/I
-
50
50
50
Feedthrough
-
1.0
1.0
1.0
Power Dissipation Capacitance (Per Package)
(Figure 15)
Typical @25
C,V
CC
=5.0 V, V
EE
=0
V
C
PD
Used to determine the no-load dynamic power
consumption:
P
D
=C
PD
V
CC
2
f+I
CC
V
CC
45
pF
IN74HC4053
511
ADDITIONAL APPLICATION CHARACTERISTICS
(GND = 0.0 V)
V
CC
V
EE
Limit
*
Symbol
Parameter
Test Conditions
V
V
25
C
Unit
BW
Maximum On-
Channel
Bandwidth or
Minimum
Frequency
Response
(Figure 5)
f
in
=1 MHz Sine Wave
Adjust f
in
Voltage to Obtain 0 dBm at V
OS
Increase f
in
Frequence Until dB Meter
Reads -3 dB
R
L
=50
, C
L
=10 pF
2.25
4.50
6.00
-2.25
-4.50
-6.00
120
120
120
MHz
-
Off-Channel
Feedthrough
Isolation
(Figure 6)
f
in
= Sine Wave
Adjust f
in
Voltage to Obtain 0 dBm at V
IS
f
in
= 10 kHz, R
L
=600
, C
L
=50 pF
2.25
4.50
6.00
-2.25
-4.50
-6.00
-50
-50
-50
dB
f
in
= 1.0 MHz, R
L
=50
, C
L
=10 pF
2.25
4.50
6.00
-2.25
-4.50
-6.00
-40
-40
-40
-
Feedthrough
Noise, Channel
Select Input to
Common O/I
(Figure 7)
V
IN
1 MHz Square Wave (t
r
= t
f
= 6 ns)
Adjust R
L
at Setup so that I
S
= 0 A Enable
= GND
R
L
=600
, C
L
=50 pF
2.25
4.50
6.00
-2.25
-4.50
-6.00
25
105
135
mVpp
R
L
=10
, C
L
=10 pF
2.25
4.50
6.00
-2.25
-4.50
-6.00
35
145
190
-
Crosstalk
Between Any
Two Switches
(Figure 14)
f
in
= Sine Wave
Adjust f
in
Voltage to Obtain 0 dBm at V
IS
f
in
= 10 kHz, R
L
=600
, C
L
=50 pF
2.25
4.50
6.00
-2.25
-4.50
-6.00
-50
-50
-50
dB
f
in
= 1 MHz, R
L
=50
, C
L
=10 pF
2.25
4.50
6.00
-2.25
-4.50
-6.00
-60
-60
-60
THD
Total Harmonic
Distortion
(Figure 16)
f
in
= 1 kHz, R
L
=10 k
, C
L
=50 pF
THD = THD
Measured
- THD
Source
V
IS
=4.0 V
PP
sine wave
V
IS
=8.0 V
PP
sine wave
V
IS
=11.0 V
PP
sine wave
2.25
4.50
6.00
-2.25
-4.50
-6.00
0.10
0.08
0.05
%
* Limits not tested. Determined by design and verified by qualification.
PDF 
ZIP