1
FN7119.4
EL5111, EL5211, EL5411
60MHz Rail-to-Rail Input-Output Op Amps
The EL5111, EL5211, and EL5411 are low power, high
voltage rail-to-rail input-output amplifiers. The EL5111
represents a single amplifier, the EL5211 contains two
amplifiers, and the EL5411 contains four amplifiers.
Operating on supplies ranging from 5V to 15V, while
consuming only 2.5mA per amplifier, the EL5111, EL5211,
and EL5411 have a bandwidth of 60MHz (-3dB). They also
provide common mode input ability beyond the supply rails,
as well as rail-to-rail output capability. This enables these
amplifiers to offer maximum dynamic range at any supply
voltage.
The EL5111, EL5211, and EL5411 also feature fast slewing
and settling times, as well as a high output drive capability of
65mA (sink and source). These features make these
amplifiers ideal for high speed filtering and signal
conditioning application. Other applications include battery
power, portable devices, and anywhere low power
consumption is important.
The EL5111 is available in 5-pin TSOT and 8-pin HMSOP
packages. The EL5211 is available in the 8-pin HMSOP
package. The EL5411 is available in space-saving 14-pin
HTSSOP packages. All feature a standard operational
amplifier pinout. These amplifiers operate over a temperature
range of -40C to +85C.
Features
Pb-Free Available (RoHS Compliant)
60MHz -3dB bandwidth
Supply voltage = 4.5V to 16.5V
Low supply current (per amplifier) = 2.5mA
High slew rate = 75V/s
Unity-gain stable
Beyond the rails input capability
Rail-to-rail output swing
180mA output short current
Applications
TFT-LCD panels
V
COM
amplifiers
Drivers for A-to-D converters
Data acquisition
Video processing
Audio processing
Active filters
Test equipment
Battery-powered applications
Portable equipment
Pinouts
EL5111
(8-PIN HMSOP)
TOP VIEW
EL5111
(5-PIN TSOT)
TOP VIEW
EL5211
(8-PIN HMSOP)
TOP VIEW
EL5411
(14-PIN HTSSOP)
TOP VIEW
NC
VS+
VOUT
NC
VS-
VIN+
VIN-
NC 1
2
3
4
8
7
6
5
-
+
1
2
3
5
4
-
+
VIN+
VS-
VOUT
VIN-
VS+
VS+
VOUTB
VINB-
VINB+
VS-
VINA+
VINA-
VOUTA 1
2
3
4
8
7
6
5
-
+
-
+
-
+
-
+
-
+
-
+
VS-
VS+
VINB+
VINB-
VOUTB
VINA+
VINA-
VOUTA
VINC+
VINC-
VOUTC
VIND+
VIND-
VOUTD
1
2
3
4
14
13
12
11
5
6
7
10
9
8
Data Sheet
October 29, 2004
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143
|
Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2004. All Rights Reserved. All other trademarks mentioned are the property of their respective owners.
2
FN7119.4
Ordering Information
PART NUMBER
PACKAGE
TAPE &
REEL
PKG. DWG. #
EL5111IWT-T7
5-Pin TSOT
7" (3K pcs)
MDP0049
EL5111IWT-T7A
5-Pin TSOT
7" (250 pcs)
MDP0049
EL5111IWTZ-T7
(Note)
5-Pin TSOT
(Pb-Free)
7" (3K pcs)
MDP0049
EL5111IWTZ-T7A
(Note)
5-Pin TSOT
(Pb-Free)
7" (250 pcs)
MDP0049
EL5111IYE
8-Pin HMSOP
-
MDP0050
EL5111IYE-T7
8-Pin HMSOP
7"
MDP0050
EL5111IYE-T13
8-Pin HMSOP
13"
MDP0050
EL5111IYEZ
(See Note)
8-Pin HMSOP
(Pb-free)
-
MDP0050
EL5111IYEZ-T7
(See Note)
8-Pin HMSOP
(Pb-free)
7"
MDP0050
EL5111IYEZ-T13
(See Note)
8-Pin HMSOP
(Pb-free)
13"
MDP0050
EL5211IYE
8-Pin HMSOP
-
MDP0050
EL5211IYE-T7
8-Pin HMSOP
7"
MDP0050
EL5211IYE-T13
8-Pin HMSOP
13"
MDP0050
EL5211IYEZ
(Note)
8-Pin HMSOP
(Pb-Free)
-
MDP0050
EL5211IYEZ-T7
(Note)
8-Pin HMSOP
(Pb-Free)
7"
MDP0050
EL5211IYEZ-T13
(Note)
8-Pin HMSOP
(Pb-Free)
13"
MDP0050
EL5411IRE
14-Pin
HTSSOP
-
MDP0048
EL5411IRE-T7
14-Pin
HTSSOP
7"
MDP0048
EL5411IRE-T13
14-Pin
HTSSOP
13"
MDP0048
EL5411IREZ
(Note)
14-Pin
HTSSOP
(Pb-Free)
-
MDP0048
EL5411IREZ-T7
(Note)
14-Pin
HTSSOP
(Pb-Free)
7"
MDP0048
EL5411IREZ-T13
(Note)
14-Pin
HTSSOP
(Pb-Free)
13"
MDP0048
NOTE: Intersil Pb-free products employ special Pb-free material sets;
molding compounds/die attach materials and 100% matte tin plate
termination finish, which are RoHS compliant and compatible with
both SnPb and Pb-free soldering operations. Intersil Pb-free products
are MSL classified at Pb-free peak reflow temperatures that meet or
exceed the Pb-free requirements of IPC/JEDEC J STD-020C.
EL5111, EL5211, EL5411
3
FN7119.4
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typ values are for information purposes only. Unless otherwise noted, all tests are
at the specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
Absolute Maximum Ratings
(T
A
= 25C)
Supply Voltage between V
S
+ and V
S
- . . . . . . . . . . . . . . . . . . . .+18V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . V
S
- - 0.5V, V
S
+0.5V
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 65mA
Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . +125C
Storage Temperature . . . . . . . . . . . . . . . . . . . . . . . .-65C to +150C
Ambient Operating Temperature . . . . . . . . . . . . . . . .-40C to +85C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
Electrical Specifications
V
S
+ = +5V, V
S
- = -5V, R
L
= 1k
to 0V, T
A
= 25C, Unless Otherwise Specified
PARAMETER
DESCRIPTION
CONDITIONS
MIN
TYP
MAX
UNIT
INPUT CHARACTERISTICS
V
OS
Input Offset Voltage
V
CM
= 0V
3
15
mV
TCV
OS
Average Offset Voltage Drift (Note 1)
7
V/C
I
B
Input Bias Current
V
CM
= 0V
2
60
nA
R
IN
Input Impedance
1
G
C
IN
Input Capacitance
2
pF
CMIR
Common-Mode Input Range
-5.5
+5.5
V
CMRR
Common-Mode Rejection Ratio
for V
IN
from -5.5V to 5.5V
50
70
dB
A
VOL
Open-Loop Gain
-4.5V
V
OUT
4.5V
62
70
dB
OUTPUT CHARACTERISTICS
V
OL
Output Swing Low
I
L
= -5mA
-4.92
-4.85
V
V
OH
Output Swing High
I
L
= 5mA
4.85
4.92
V
I
SC
Short-Circuit Current
180
mA
I
OUT
Output Current
65
mA
POWER SUPPLY PERFORMANCE
PSRR
Power Supply Rejection Ratio
V
S
is moved from 2.25V to 7.75V
60
80
dB
I
S
Supply Current
No load (EL5111)
2.5
4.5
mA
No load (EL5211)
5
7.5
mA
No load (EL5411)
10
15
mA
DYNAMIC PERFORMANCE
SR
Slew Rate (Note 2)
-4.0V
V
OUT
4.0V, 20% to 80%
75
V/s
t
S
Settling to +0.1% (A
V
= +1)
(A
V
= +1), V
O
= 2V step
80
ns
BW
-3dB Bandwidth
60
MHz
GBWP
Gain-Bandwidth Product
32
MHz
PM
Phase Margin
50
CS
Channel Separation
f = 5MHz (EL5211 & EL5411 only)
110
dB
d
G
Differential Gain (Note 3)
R
F
= R
G
= 1k
and V
OUT
= 1.4V
0.17
%
d
P
Differential Phase (Note 3)
R
F
= R
G
= 1k
and V
OUT
= 1.4V
0.24
NOTES:
1. Measured over operating temperature range.
2. Slew rate is measured on rising and falling edges.
3. NTSC signal generator used.
EL5111, EL5211, EL5411
4
FN7119.4
Electrical Specifications
V
S
+ = +5V, V
S
- = 0V, R
L
= 1k
to 2.5V, T
A
= 25C, Unless Otherwise Specified
PARAMETER
DESCRIPTION
CONDITION
MIN
TYP
MAX
UNIT
INPUT CHARACTERISTICS
V
OS
Input Offset Voltage
V
CM
= 2.5V
3
15
mV
TCV
OS
Average Offset Voltage Drift (Note 4)
7
V/C
I
B
Input Bias Current
V
CM
= 2.5V
2
60
nA
R
IN
Input Impedance
1
G
C
IN
Input Capacitance
2
pF
CMIR
Common-Mode Input Range
-0.5
+5.5
V
CMRR
Common-Mode Rejection Ratio
for V
IN
from -0.5V to 5.5V
45
66
dB
A
VOL
Open-Loop Gain
0.5V
V
OUT
4.5V
62
70
dB
OUTPUT CHARACTERISTICS
V
OL
Output Swing Low
I
L
= -5mA
80
150
mV
V
OH
Output Swing High
I
L
= 5mA
4.85
4.92
V
I
SC
Short-circuit Current
180
mA
I
OUT
Output Current
65
mA
POWER SUPPLY PERFORMANCE
PSRR
Power Supply Rejection Ratio
V
S
is moved from 4.5V to 15.5V
60
80
dB
I
S
Supply Current
No load (EL5111)
2.5
4.5
mA
No load (EL5211)
5
7.5
mA
No load (EL5411)
10
15
mA
DYNAMIC PERFORMANCE
SR
Slew Rate (Note 5)
1V
V
OUT
4V, 20% to 80%
75
V/s
t
S
Settling to +0.1% (A
V
= +1)
(A
V
= +1), V
O
= 2V step
80
ns
BW
-3dB Bandwidth
60
MHz
GBWP
Gain-Bandwidth Product
32
MHz
PM
Phase Margin
50
CS
Channel Separation
f = 5MHz (EL5211 & EL5411 only)
110
dB
d
G
Differential Gain (Note 6)
R
F
= R
G
= 1k
and V
OUT
= 1.4V
0.17
%
d
P
Differential Phase (Note 6)
R
F
= R
G
= 1k
and V
OUT
= 1.4V
0.24
NOTES:
4. Measured over operating temperature range.
5. Slew rate is measured on rising and falling edges.
6. NTSC signal generator used.
Electrical Specifications
V
S
+ = +15V, V
S
- = 0V, R
L
= 1k
to 7.5V, T
A
= 25C, Unless Otherwise Specified
PARAMETER
DESCRIPTION
CONDITION
MIN
TYP
MAX
UNIT
INPUT CHARACTERISTICS
V
OS
Input Offset Voltage
V
CM
= 7.5V
3
15
mV
TCV
OS
Average Offset Voltage Drift (Note 7)
7
V/C
I
B
Input Bias Current
V
CM
= 7.5V
2
60
nA
R
IN
Input Impedance
1
G
5
FN7119.4
C
IN
Input Capacitance
2
pF
CMIR
Common-Mode Input Range
-0.5
+15.5
V
CMRR
Common-Mode Rejection Ratio
for V
IN
from -0.5V to 15.5V
53
72
dB
A
VOL
Open-Loop Gain
0.5V
V
OUT
14.5V
62
70
dB
OUTPUT CHARACTERISTICS
V
OL
Output Swing Low
I
L
= -5mA
80
150
mV
V
OH
Output Swing High
I
L
= 5mA
14.85
14.92
V
I
SC
Short-circuit Current
180
mA
I
OUT
Output Current
65
mA
POWER SUPPLY PERFORMANCE
PSRR
Power Supply Rejection Ratio
V
S
is moved from 4.5V to 15.5V
60
80
dB
I
S
Supply Current
No load (EL5111)
2.5
4.5
mA
No load (EL5211)
5
7.5
mA
No load (EL5411)
10
15
mA
DYNAMIC PERFORMANCE
SR
Slew Rate (Note 8)
1V
V
OUT
14V, 20% to 80%
75
V/s
t
S
Settling to +0.1% (A
V
= +1)
(A
V
= +1), V
O
= 2V step
80
ns
BW
-3dB Bandwidth
60
MHz
GBWP
Gain-Bandwidth Product
32
MHz
PM
Phase Margin
50
CS
Channel Separation
f = 5MHz (EL5211 & EL5411 only)
110
dB
d
G
Differential Gain (Note 9)
R
F
= R
G
= 1k
and V
OUT
= 1.4V
0.16
%
d
P
Differential Phase (Note 9)
R
F
= R
G
= 1k
and V
OUT
= 1.4V
0.22
NOTES:
7. Measured over operating temperature range
8. Slew rate is measured on rising and falling edges
9. NTSC signal generator used
Electrical Specifications
V
S
+ = +15V, V
S
- = 0V, R
L
= 1k
to 7.5V, T
A
= 25C, Unless Otherwise Specified
(Continued)
PARAMETER
DESCRIPTION
CONDITION
MIN
TYP
MAX
UNIT
PDF 
ZIP