1
FN7185.2
EL5210, EL5410
30MHz Rail-to-Rail Input-Output Op Amps
The EL5210 and EL5410 are low power, high voltage rail-to-
rail input-output amplifiers. The EL5210 contains two
amplifiers in one package and the EL5410 contains four
amplifiers. Operating on supplies ranging from 5V to 15V,
while consuming only 2.5mA per amplifier, the EL5410 and
EL5210 have a bandwidth of 30MHz (-3dB). They also
provide common mode input ability beyond the supply rails,
as well as rail-to-rail output capability. This enables these
amplifiers to offer maximum dynamic range at any supply
voltage.
The EL5410 and EL5210 also feature fast slewing and
settling times, as well as a high output drive capability of
30mA (sink and source). These features make these
amplifiers ideal for high speed filtering and signal
conditioning application. Other applications include battery
power, portable devices, and anywhere low power
consumption is important.
The EL5410 is available in a space-saving 14-Pin TSSOP
package, as well as the industry-standard 14-Pin SOIC. The
EL5210 is available in the 8-Pin MSOP and 8-Pin SOIC
packages. Both feature a standard operational amplifier pin
out. These amplifiers operate over a temperature range of
-40C to +85C.
Features
30MHz -3dB bandwidth
Supply voltage = 4.5V to 16.5V
Low supply current (per amplifier) = 2.5mA
High slew rate = 33V/s
Unity-gain stable
Beyond the rails input capability
Rail-to-rail output swing
Available in both standard and space-saving fine pitch
packages
Pb-Free available (RoHS compliant)
Applications
Driver for A-to-D Converters
Data Acquisition
Video Processing
Audio Processing
Active Filters
Test Equipment
Battery Powered Applications
Portable Equipment
Pinouts
1
2
3
4
14
13
12
11
5
6
7
10
9
8
-
+
-
+
-
+
-
+
EL5410
(14-PIN TSSOP, SOIC)
TOP VIEW
VS-
VS+
VINB+
VINB-
VOUTB
VINA+
VINA-
VOUTA
VINC+
VINC-
VOUTC
VIND+
VIND-
VOUTD
1
2
3
4
8
7
6
5
-
+
-
+
VS-
VS+
VINA+
VINA-
VOUTA
VOUTB
VINB-
VINB+
EL5210
(8-PIN MSOP, SOIC)
TOP VIEW
Data Sheet
May 6, 2005
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-352-6832
|
Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2003-2005. All Rights Reserved
All other trademarks mentioned are the property of their respective owners.
2
FN7185.2
May 6, 2005
Ordering Information
PART NUMBER
PACKAGE
TAPE & REEL PKG. DWG. #
EL5210CS
8-Pin SOIC
-
MDP0027
EL5210CS-T7
8-Pin SOIC
7"
MDP0027
EL5210CS-T13
8-Pin SOIC
13"
MDP0027
EL5210CSZ
(See Note)
8-Pin SOIC
(Pb-free)
-
MDP0027
EL5210CSZ-T7
(See Note)
8-Pin SOIC
(Pb-free)
7"
MDP0027
EL5210CSZ-T13
(See Note)
8-Pin SOIC
(Pb-free)
13"
MDP0027
EL5210CY
8-Pin MSOP
-
MDP0043
EL5210CY-T7
8-Pin MSOP
7"
MDP0043
EL5210CY-T13
8-Pin MSOP
13"
MDP0043
EL5210CYZ
(See Note)
8-Pin MSOP
(Pb-free)
-
MDP0043
EL5210CYZ-T7
(See Note)
8-Pin MSOP
(Pb-free)
7"
MDP0043
EL5210CYZ-T13
(See Note)
8-Pin MSOP
(Pb-free)
13"
MDP0043
EL5410CS
14-Pin SOIC
-
MDP0027
EL5410CS-T7
14-Pin SOIC
7"
MDP0027
EL5410CS-T13
14-Pin SOIC
13"
MDP0027
EL5410CSZ
(See Note)
14-Pin SOIC
(Pb-free)
-
MDP0027
EL5410CSZ-T7
(See Note)
14-Pin SOIC
(Pb-free)
7"
MDP0027
EL5410CSZ-T13
(See Note)
14-Pin SOIC
(Pb-free)
13"
MDP0027
EL5410CR
14-Pin TSSOP
-
MDP0044
EL5410CR-T7
14-Pin TSSOP
7"
MDP0044
EL5410CR-T13
14-Pin TSSOP
13"
MDP0044
EL5410CRZ
(See Note)
14-Pin TSSOP
(Pb-free)
-
MDP0044
EL5410CRZ-T7
(See Note)
14-Pin TSSOP
(Pb-free)
7"
MDP0044
EL5410CRZ-T13
(See Note)
14-Pin TSSOP
(Pb-free)
13"
MDP0044
Add "-T" suffix for tape and reel.
NOTE: Intersil Pb-free products employ special Pb-free material
sets; molding compounds/die attach materials and 100% matte tin
plate termination finish, which are RoHS compliant and compatible
with both SnPb and Pb-free soldering operations. Intersil Pb-free
products are MSL classified at Pb-free peak reflow temperatures that
meet or exceed the Pb-free requirements of IPC/JEDEC J STD-020.
EL5210, EL5410
3
FN7185.2
May 6, 2005
NOTES:
1. Measured over operating temperature range
2. Slew rate is measured on rising and falling edges
3. NTSC signal generator used
Absolute Maximum Ratings
(T
A
= 25C)
Supply Voltage between V
S
+ and V
S
-. . . . . . . . . . . . . . . . . . . .+18V
Input Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . .V
S
- -0.5V, V
S
+0.5V
Maximum Continuous Output Current . . . . . . . . . . . . . . . . . . . 30mA
Maximum Die Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . +125C
Storage Temperature. . . . . . . . . . . . . . . . . . . . . . . .-65C to +150C
Operating Temperature . . . . . . . . . . . . . . . . . . . . . . .-40C to +85C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Curves
CAUTION: Stresses above those listed in "Absolute Maximum Ratings" may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
IMPORTANT NOTE: All parameters having Min/Max specifications are guaranteed. Typical values are for information purposes only. Unless otherwise noted, all tests
are at the specified temperature and are pulsed tests, therefore: T
J
= T
C
= T
A
Electrical Specifications
V
S
+ = +5V, V
S
- = -5V, R
L
= 1k
and C
L
= 12pF to 0V, T
A
= 25C unless otherwise specified.
PARAMETER
DESCRIPTION
CONDITION
MIN
TYP
MAX
UNIT
INPUT CHARACTERISTICS
V
OS
Input Offset Voltage
V
CM
= 0V
3
15
mV
TCV
OS
Average Offset Voltage Drift (Note 1)
7
V/C
I
B
Input Bias Current
V
CM
= 0V
2
60
nA
R
IN
Input Impedance
1
G
C
IN
Input Capacitance
2
pF
CMIR
Common-Mode Input Range
-5.5
+5.5
V
CMRR
Common-Mode Rejection Ratio
for V
IN
from -5.5V to 5.5V
50
70
dB
A
VOL
Open-Loop Gain
-4.5V
V
OUT
4.5V
65
80
dB
OUTPUT CHARACTERISTICS
V
OL
Output Swing Low
I
L
= -5mA
-4.9
-4.8
V
V
OH
Output Swing High
I
L
= 5mA
4.8
4.9
V
I
SC
Short Circuit Current
120
mA
I
OUT
Output Current
30
mA
POWER SUPPLY PERFORMANCE
PSRR
Power Supply Rejection Ratio
V
S
is moved from 2.25V to 7.75V
60
80
dB
I
S
Supply Current (Per Amplifier)
No Load
2.5
3.75
mA
DYNAMIC PERFORMANCE
SR
Slew Rate (Note 2)
-4.0V
V
OUT
4.0V, 20% to 80%
33
V/s
t
S
Settling to +0.1% (A
V
= +1)
(A
V
= +1), V
O
= 2V Step
140
ns
BW
-3dB Bandwidth
30
MHz
GBWP
Gain-Bandwidth Product
20
MHz
PM
Phase Margin
50
CS
Channel Separation
f = 5MHz
110
dB
d
G
Differential Gain (Note 3)
R
F
= R
G
= 1k
and V
OUT
= 1.4V
0.12
%
d
P
Differential Phase (Note 3)
R
F
= R
G
= 1k
and V
OUT
= 1.4V
0.17
EL5210, EL5410
4
FN7185.2
May 6, 2005
NOTES:
1. Measured over operating temperature range
2. Slew rate is measured on rising and falling edges
3. NTSC signal generator used
Electrical Specifications
V
S
+ = 5V, V
S
- = 0V, R
L
= 1k
and C
L
= 12pF to 2.5V, T
A
= 25C unless otherwise specified.
PARAMETER
DESCRIPTION
CONDITION
MIN
TYP
MAX
UNIT
INPUT CHARACTERISTICS
V
OS
Input Offset Voltage
V
CM
= 2.5V
3
15
mV
TCV
OS
Average Offset Voltage Drift (Note 1)
7
V/C
I
B
Input Bias Current
V
CM
= 2.5V
2
60
nA
R
IN
Input Impedance
1
G
C
IN
Input Capacitance
2
pF
CMIR
Common-Mode Input Range
-0.5
+5.5
V
CMRR
Common-Mode Rejection Ratio
for V
IN
from -0.5V to 5.5V
45
66
dB
A
VOL
Open-Loop Gain
0.5V
V
OUT
4.5V
65
80
dB
OUTPUT CHARACTERISTICS
V
OL
Output Swing Low
I
L
= -5mA
100
200
mV
V
OH
Output Swing High
I
L
= 5mA
4.8
4.9
V
I
SC
Short Circuit Current
120
mA
I
OUT
Output Current
30
mA
POWER SUPPLY PERFORMANCE
PSRR
Power Supply Rejection Ratio
V
S
is moved from 4.5V to 15.5V
60
80
dB
I
S
Supply Current (Per Amplifier)
No Load
2.5
3.75
mA
DYNAMIC PERFORMANCE
SR
Slew Rate (Note 2)
1V
V
OUT
4V, 20% o 80%
33
V/s
t
S
Settling to +0.1% (A
V
= +1)
(A
V
= +1), V
O
= 2V Step
140
ns
BW
-3dB Bandwidth
30
MHz
GBWP
Gain-Bandwidth Product
20
MHz
PM
Phase Margin
50
CS
Channel Separation
f = 5MHz
110
dB
d
G
Differential Gain (Note 3)
R
F
= R
G
= 1k
and V
OUT
= 1.4V
0.30
%
d
P
Differential Phase (Note 3)
R
F
= R
G
= 1k
and V
OUT
= 1.4V
0.66
EL5210, EL5410
5
FN7185.2
May 6, 2005
NOTES:
1. Measured over operating temperature range
2. Slew rate is measured on rising and falling edges
3. NTSC signal generator used
Electrical Specifications
V
S
+ = 15V, V
S
- = 0V, R
L
= 1k
and C
L
= 12pF to 7.5V, T
A
= 25C unless otherwise specified.
PARAMETER
DESCRIPTION
CONDITION
MIN
TYP
MAX
UNIT
INPUT CHARACTERISTICS
V
OS
Input Offset Voltage
V
CM
= 7.5V
3
15
mV
TCV
OS
Average Offset Voltage Drift (Note 1)
7
V/C
I
B
Input Bias Current
V
CM
= 7.5V
2
60
nA
R
IN
Input Impedance
1
G
C
IN
Input Capacitance
2
pF
CMIR
Common-Mode Input Range
-0.5
+15.5
V
CMRR
Common-Mode Rejection Ratio
for V
IN
from -0.5V to 15.5V
53
72
dB
A
VOL
Open-Loop Gain
0.5V
V
OUT
14.5V
65
80
dB
OUTPUT CHARACTERISTICS
V
OL
Output Swing Low
I
L
= -7.5mA
170
350
mV
V
OH
Output Swing High
I
L
= 7.5mA
14.65
14.83
V
I
SC
Short Circuit Current
120
mA
I
OUT
Output Current
30
mA
POWER SUPPLY PERFORMANCE
PSRR
Power Supply Rejection Ratio
V
S
is moved from 4.5V to 15.5V
60
80
dB
I
S
Supply Current (Per Amplifier)
No Load
2.5
3.75
mA
DYNAMIC PERFORMANCE
SR
Slew Rate (Note 2)
1V
V
OUT
14V, 20% o 80%
33
V/s
t
S
Settling to +0.1% (A
V
= +1)
(A
V
= +1), V
O
= 2V Step
140
ns
BW
-3dB Bandwidth
30
MHz
GBWP
Gain-Bandwidth Product
20
MHz
PM
Phase Margin
50
CS
Channel Separation
f = 5MHz
110
dB
d
G
Differential Gain (Note 3)
R
F
= R
G
= 1k
and V
OUT
= 1.4V
0.10
%
d
P
Differential Phase (Note 3)
R
F
= R
G
= 1k
and V
OUT
= 1.4V
0.11
EL5210, EL5410
PDF 
ZIP