1
FN7231
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143
|
Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright Intersil Americas Inc. 2003. All Rights Reserved. Elantec is a registered trademark of Elantec Semiconductor, Inc.
All other trademarks mentioned are the property of their respective owners.
PRELIMINARY
EL6835
Dual 4-Channel Driver with Oscillator &
LVDS
The EL6835 is a high performance,
dual output, laser driver for writeable
`super-combo' CD - DVD drives. The
ENA pin enables the chip, while the SEL1 pin selects the
I
OUT
pin. Various waveforms can be generated where the
amplitude is determined by the currents flowing into I
INR
,
I
IN2
, I
IN3
, and I
IN4
. The timing is determined by the signals
at WEN2-WEN2B, WEN3-WEN3B, and WEN4-WEN4B. The
oscillator is enabled when OSEN is high. The amplified I
INR
current of the selected channel is enabled when the ENA pin
is high. The total output current is the sum of the read
current, the enabled write currents, and the oscillator current
when enabled.
Usually a voltage DAC will drive a resistor that is in series
with the I
INR
, I
IN2
, I
IN3
, and I
IN4
input. The resistor allows
the user to optimize the current gain for each channel.
Output write current pulses are enabled when a high is
applied to the WEN2-WEN2B, WEN3-WEN3B, or WEN-
WEN4B pin. The write current will flow to the selected
output. When SEL1 is high I
OUT1
is selected. WENRB
enables read and oscillator current when low.
The R
F
oscillators frequency is determined by R
FREQ1
or
R
FREQ2
, and its amplitude by R
AMP1
or R
AMP2
.
Features
Two channels for CD or DVD
Voltage-controlled output current source requiring one
external set resistor per channel
Rise time = 0.8ns
Fall time = 0.8ns
Channel 2 to 250mA max
Channel 3 to 150mA max
Channel 4 to 100mA max
External 100
LVDS termination
On chip oscillator with frequency and amplitude control by
use of external resistors to ground
Oscillator frequency to 600MHz
Oscillator amplitude to 100mA
P-P
Single +5V supply (10%)
Chip ENAs for power savings
Applications
Super combo drives
Pinout
EL6835
(32-PIN LPP)
TOP VIEW
Ordering Information
PART
NUMBER
TEMP. RANGE
PACKAGE
PKG. DWG. #
EL6835CL
0C to +70C
32-Pin LPP
MDP0046
RFREQ2
GND
WENRB
WEN2
WEN2B
WEN3
WEN3B
VDDN
IOUT1
IOUT1
GND
RAMP1
RAMP2
VDDN
RF
R
E
Q1
II
N4
II
N3
II
N2
II
NR
OSE
N
GND
GND
NC
SE
L1
IOUT2
IOUT2
WEN4
WEN4B
ENA
GND
GND
VDDQ
25
24
23
22
21
20
19
32
31
30
29
28
10
11
12
13
14
1
2
3
4
5
6
7
THERMAL
PAD
8
9
18
17
15
27
16
26
Data Sheet
July 1, 2003
Get FULL DATASHEET
2
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation's quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
EL6835
PDF 
ZIP