The GenesysTM family of programmable power supplies sets a new standard for flexible, reliable,
AC/DC power systems in OEM, Industrial and Laboratory applications.
Features include:
Highest Power Density available 1500W in 1U
Wide Range Input 85 - 265Vac Continuous, single phase, 47/63Hz
Active Power Factor Correction 0.99
Output up to 600V, Current up to 200A
Built in RS232/RS485 Interface
Software Calibration
Last Setting Memory
High Resolution 16 bits ADCs & DACs
Reliable Encoders for Voltage and Current Adjustment
Constant Voltage/Constant Current auto crossover
Parallel Operation with Active Current Sharing
Independent Remote ON/OFF and Remote Enable/Disable
External Analog Programming and Monitoring
Reliable Modular and SMT Design
19" Rack Mounted ATE and OEM applications
Five Year Warranty
Optional Isolated Analog Programming and Monitoring
Optional GPIB (SCPI) Interface
LabView
drivers ( LabView
is registered trademark of National Instruments Corporation )
Worldwide Safety Agency Approvals CE Mark for LVD and EMC Regulation
Test and Measurement
Last setting memory simplifies test design and requires no battery backup.
Built in RS232/RS485 gives maximum system flexibility along with 0-5V and 0-10V, selectable analog programming
Wide range of available inputs allows testing of many different devices.
Semiconductor Burn-in
Safe Start may be enabled to restart at zero output to protect load.
Wide range input (85-265VAC) with Active Power Factor correction rides through input transients easily.
Component Test
High power density, zero stacking and single wire parallel operation give maximum system flexibility
Laser Diode
OVP is directly set on Voltage Meter, assuring accurate protection settings.
Current Limit Fold Back assures load is protected from current surges.
Heater Supplies
Smooth, reliable encoders enhance front panel control.
Remote analog programming is user selectable 0-5V or 0-10V.
RF Amplifiers and Magnets
Robust design assures stable operation under a wide variety of loads.
Excellent linearity in voltage and current mode.
Applications
GenesysTM power supplies have been designed to meet the demands of a wide variety of applications.
GenesysTM
750W/1500W-1U
1|
1. Remote/Local Output Voltage Sense Connections
2. DIP Switches select 0-5V or 0-10V Programming and other functions.
3. DB25 (Female) connector allows (Non-isolated) Analog Program and Monitor as well as other functions.
4. RS485 Out to other Genesys Power Supplies
5. RS232/RS485 IN Remote Serial Programming
6. Output Terminals are rugged bus bars for 6-60V Output, higher output voltage models have terminal block connector.
7. Exit air assures reliable operation when zero stacked
8. Wide-Range Input 85-265VAC continuous, 47/63Hz with Active Power Factor Correction (0.99)
AC Input Connector 750W: IEC320, 1500W: Screw terminal Model Shown
9. Position for Optional Isolated Analog Programming or GPIB Digital Interface model shown
Front Panel Description
Rear Panel Description
1. AC On/Off
2. Air Intake allows zero stacking for maximum system flexibility and power density
3. Reliable encoder controls Output Voltage and sets Address.
4. Volt Meter shows Output Voltage and directly displays OVP, UVL and Address settings.
5. Amp Meter also displays baud rate.
6. Reliable encoder controls Output Current and sets baud rate.
7. Function/Status LED's
8. Pushbuttons allow flexible user configuration
Coarse and Fine Voltage and Current Adjustment of Output
Preview Settings and Set Voltage while in Current Mode or with Output OFF
Set OVP and UVL Limits
Set Current Foldback
Local/Remote Mode and select Address and Baud Rate
Output ON/OFF and Auto Start/Safe Start Mode
Alarm
Fine Control
Preview Settings
Foldback Mode
Remote Mode
Output On
|2
Genesys TM 750W/1500W Specifications
GenesysTM
750W/1500W-1U
3|
*1: Minimum voltage is guaranteed to maximum 0.2% of Vomax.
*2: Minimum current is guaranteed to maximum 0.4% of Iomax.
2.Display
3.Indications
Voltage
Current
Voltage, Current, Alarm, Fine, Preview, Foldback, Local, Output On
4 digits , accuracy: 0.5%+/-1 count
4 digits, accuracy: 0.5%+/-1 count
X
X
X
X
X
X
1.5 FRONT PANEL
1.Control functions
Vout/ Iout manual adjust by separate encoders (coarse and fine adjustment selectable)
OVP/UVL manual adjust by Volt. Adjust encoder
Address selection by Voltage (or current) adjust encoder. No of addresses:31
AC on/off, Output on/off, Re-start modes (auto, safe), Foldback control (CV to CC), Go to local control
RS232/485 and IEEE488.2 selection by IEEE enable switch and DIP switch
Baud rate selection: 1200,2400,4800,9600 and 19,200 bps
X
X
X
X
X
X
X
X
X
X
X
X
OVP Programming
Resolution (0.1% of Vomax)
Accuracy (1% of Vomax)
mV
mV
X
X
X
X
Readback Current
Resolution (0.012% of Iomax )
Accuracy (0.1% of Iomax+0.3% of Io Actual Output)
Resolution (0.012% of Iomax )
Accuracy (0.1% of Iomax+0.3% of Io Actual Output)
mA
mA
mA
mA
12
400
24
800
10.8
360
21.6
720
7.2
240
14.4
480
4.56
152
9.12
304
3.0
100
6
200
2.28
76
4.56
152
1.50
50
3.0
100
1.14
38
2.28
76
0.9
30
1.80
60
0.60
20
1.20
40
0.30
10
0.60
20
0.16
5.2
0.32
10.4
X
X
X
X
Readback Voltage
Resolution (0.012% of Vomax)
Accuracy (0.1%Vomax+0.1% of Vo Actual Output)
mV
mV
0.72
12
0.96
16
1.50
25
2.40
40
3.60
60
4.80
80
7.2
120
9.6
160
12
200
18
300
36
600
72
1200
X
X
X
X
Remote Current Programming (16 bit)
Resolution (0.012% of Iomax)
Accuracy (0.05% of Iomax+0.05% of Io Actual Output)
Resolution (0.012% of Iomax)
Accuracy (0.05% of Iomax+0.05% of Io Actual Output)
mA
mA
mA
mA
12
10
24
20
10.8
9
21.6
18
7.2
6
14.4
12
4.56
3.8
9.12
7.6
3.0
2.5
6
5
2.28
1.9
4.56
3.8
1.50
1.25
3.0
2.5
1.14
0.95
2.28
1.9
0.90
0.75
1.80
1.50
0.60
0.5
1.20
1
0.30
0.25
0.60
0.5
0.16
0.13
0.32
0.26
X
X
X
X
1.6 Interface RS232&RS485 or Optional GPIB Interface
Model
Remote Voltage Programming (16 bit)
Resolution (0.012% of Vomax)
Accuracy (0.05%Vomax+0.05% of Vo Actual Output)
V
mV
mV
6
0.72
6.0
8
0.96
8.0
12.5
1.50
12.5
20
2.40
20
30
3.60
30
40
4.80
40
60
7.2
60
80
9.6
80
100
12
100
150
18
150
300
36
300
600
72
600
750W
X
X
1500W
X
X
X
X
6
60
8
80
12
125
20
200
29
300
39
400
59
600
78
800
98
1000
146
1500
293
3000
586
6000
1.4 ANALOG PROGRAMMING AND MONITORING
1.Vout Voltage Programming
2.Iout Voltage Programming
3.Vout Resistor Programming
4.Iout Resistor Programming
5.On/Off control (rear panel)
6.Output Current monitor
7.Output Voltage monitor
8.Power Supply OK signal
9. CV/CC indicator
10. Enable/Disable
0~100%, 0~5V or 0~10V, user select. Accuracy and linearity:+/-0.5% of rated Vout.
0~100%, 0~5V or 0~10V, user select. Accuracy and linearity:+/-1% of rated Iout.
0~100%, 0~5/10Kohm full scale,user select.,Accuracy and linearity:+/-1% of rated Vout.
0~100%, 0~5/10Kohm full scale,user select. Accuracy and linearity:+/-1.5% of rated Iout.
By electrical. Voltage: 0~0.6V/2~15V,or dry contact ,user selectable logic
0~5V or 0~10V , accuracy:1% , user selectable
0~5V or 0~10V ,accuracy:1% ,user selectable
5V-OK, 0V-Fail 500ohm impedance
CV: TTL high (4~5V) source: 10mA, CC: TTL low (0~0.4V):10mA
Dry contact. Open:off , Short: on. Max. voltage at Enable/Disable in: 6V
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
1.1 CONSTANT VOLTAGE MODE
1.Max.line regulation ( 0.01% of Vo+ 2mV )(*4)
2.Max load regulation ( 0.01% of Vo+2mV )(*5)
3.Ripple and noise p-p 20MHz
4.Ripple r.m.s 5Hz~1MHz
5.Remote sense compensation/line
6.Temp. coefficient
7.Up-prog. response time, 0~Vomax
8.Down-prog response time full-load
9.Down-prog response time no-load
10.Transient response time (*8)
mV
mV
mV
mV
V
PPM/
C
mS
mS
mS
2.6
2.6
60
8
1
100PPM/
C from rated output voltage,following 30 minutes warm up
80mS , N.L/F.L , resistive load
10
500
Less than 1mSec for models up to and including 100V. 2msec for models above 100V
2.8
2.8
60
8
1
600
3.3
3.3
60
8
1
50
700
4
4
60
8
1
800
5
5
60
8
1.5
900
6
6
60
8
2
80
1000
8
8
60
8
3
1100
10
10
80
8
4
150mS , N.L/F.L , resistive load
1200
12
12
80
8
5
1500
17
17
100
10
5
150
2000
32
32
125
25
5
2500
62
62
300
60
5
4000
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
X
1.2 CONSTANT CURRENT MODE
1.Max.line regulation (0.01% of Io+ 2mA)(*4)
2.Max.load regulation (0.01% of Io+5mA)(*6)
3.Ripple r.m.s 5Hz~1MHz . (*7)
1.Max.line regulation (0.01% of Io+ 2mA)(*4)
2.Max.load regulation (0.01% of Io+5mA)(*6)
3.Ripple r.m.s 5Hz~1MHz .(*7)
4.Temp. coefficient
mA
mA
mA
mA
mA
mA
PPM/
C
12
15
200
2
5
400
100PPM/
C from rated output voltage,following 30 minutes warm up
11
14
180
2
5
360
8
11
120
2
5
240
5.8
8.8
76
2
5
152
4.5
7.5
63
2
5
125
3.9
6.9
48
2
5
95
3.25
6.25
38
2
5
75
2.95
5.95
29
2
5
57
2.75
5.75
23
2
5
45
2.5
5.5
18
2
5
35
2.25
5.25
13
2
5
25
2.13
5.13
8
2
5
12
X
X
X
X
X
X
X
X
1.3 PROTECTIVE FUNCTIONS
1. OCP
2. OCP Foldback
3. OVP type
4. OVP trip point
5. Over Temp. Protection
0~105% Constant Current
Output shut down when power supply change from CV to CC. User selectable.
Inverter shut-down, manual reset by AC input recycle or by OUT button
0.5~7.5V
User selectable , latched or non latched
0.5~10V 1~15V
1~24V
2~36V 2~44V 5~66V
5~88V 5~110V 5~165V 5~330V 5~660V
X
X
X
X
X
X
X
X
X
X
*7: For 6V models the ripple is measured at 2~6V output voltage and full output current. For other models, the ripple is measured at 10~100% output voltage and full output current.
*8: Time for the output voltage to recover within 0.5% of its rated for a load change 10~90% of rated output , Output set-point:10~100%.
*3: At maximum output power.
*4: 85~132Vac or 170~265Vac, constant load.
*5: From No-load to Full-load, constant input voltage.
*6: For load voltage change, equal to the unit voltage rating, constant input voltage.
GEN
V
A
W
6-100
6
100
600
8-90
8
90
720
12.5-60
12.5
60
750
20-38
20
38
760
30-25
30
25
750
40-19
40
19
760
60-12.5
60
12.5
750
80-9.5
80
9.5
760
100-7.5
100
7.5
750
150-5
150
5
750
300-2.5
300
2.5
750
600-1.3
600
1.3
780
X
X
X
X
1.0 MODEL
1.Rated output voltage (*1)
2.Rated Output Current (*2)
3.Rated Output Power
750W
1500W
3.Rated Output Power
1.0 MODEL
1.Rated output voltage(*1)
2.Rated Output Current(*2)
4.Efficiency at 100/200Vac (*3)
GEN
V
A
W
%
6-200
6
200
1200
77/80
8-180
8
180
1440
78/81
12.5-120
12.5
120
1500
81/84
20-76
20
76
1520
83/86
30-50
30
50
1500
83/86
40-38
40
38
1520
84/88
60-25
60
25
1500
84/88
80-19
80
19
1520
84/88
100-15
100
15
1500
84/88
150-10
150
10
1500
84/88
300-5
300
5
1500
83/87
600-2.6
600
2.6
1560
83/87
X
X
X
X
X
X
Accuracy -Values have been calculated at Vomax & Io max
General Specifications GenesysTM 750W/1500W
Outline Drawing GenesysTM 750W/1500W Units
|4
NOTE
1. PLUG CONNECTORS INCLUDED WITH THE POWER SUPPLY
2. CHASSIS SLIDES MOUNTING HOLES #10-32 MARKED "A"
GENERAL DEVICES P/N: CC301-00-S160 OR EQUIVALENT
*1: For cases where conformance to various safety standards (UL, IEC etc.) is required, to be described as 100-240Vac (50/60Hz).
2.1 INPUT CHARACTERISTICS
1. Input voltage/freq. (*1)
2. Power Factor
0.99 @100/200Vac, rated output power.
3. EN61000-3-2,3 compliance
Complies with EN61000-3-2 class A and EN61000-3-3 at 20~100% output power.
4. Input current 100/200Vac
5. Inrush current 100/200Vac
750W :Less than 25A,
1500W :Less than 50A
6. Hold-up time
More than 20mS , 100Vac , at 100% load.
750W :10.5A / 5A,
1500W :21A / 11A
85~265Vac continuous, 47~63Hz, single phase
2.6 MECHANICAL CONSTRUCTION
1. Cooling
2. Dimensions (WxHxD)
W: 422.8mm, H: 43.6mm, D: 432.8mm (excluding connectors, encoders, handles etc..)
3. Weight
750W: 7Kg (15.4 Lbs)
1500W: 8.5Kg (18.7 Lbs)
4. AC Input connector
750W: AC Inlet IEC320.
1500W: screw terminal block, Phoenix P/N: FRONT-4-H-7.62 , with strain relief
5.Output connectors
6V to 60V models: bus-bars (hole 8.5mm).
80V to 600V models :terminal block ,Phoenix P/N: FRONT-4-H-7.62
Forced air flow: from front to rear. No ventilation holes at the top or bottom of the chassis Variable fan speed.
2.7 RELIABILITY SPECS
1. Warranty
5 years.
1. Parallel Operation
2. Series Operation
Up to 4 units in master/slave mode with single wire current balance connection
Up to 2 units. with external diodes.
600V Max to Chassis ground
2.2 POWER SUPPLY CONFIGURATION
2.3 ENVIRONMENTAL CONDITIONS
1. Operating temp
2. Storage temp
-20~70
C
3. Operating humidity
30~90% RH (no condensation).
4. Storage humidity
10~95% RH (no condensation).
5. Vibration
MIL-810E, method 514.4 , test cond. I-3.3.1 . The EUT is fixed to the vibrating surface.
6. Shock
Less than 20G , half sine , 11mSec. Unit is unpacked.
7. Altitude
Operating: 10000ft (3000m) , Non operating: 40000ft (12000m).
0~50
C, 100% load.
EN55022A, FCC part 15-A, VCCI-1.
2.4 EMC
1.Applicable standards:
EN55024
2.ESD
IEC1000-4-2. Air-disch.-8KV, contact disch.-4KV
3.Fast transients
IEC1000-4-4. 2KV
4.Surge immunity
IEC1000-4-5. 1KV line to line, 2KV line to ground
5.Conducted immunity
IEC1000-4-6, 3V
6.Radiated immunity
IEC1000-4-3, 3V/m
7.Conducted emission
EN55022B,FCC part 15J-B,VCCI-2
8.Radiated emission
EN55022A,FCC part 15-A,VCCI-1
9.Voltage dips
EN61000-4-11
10. Conducted emission
11. Radiated emission
EN55022B, FCC part 15-B, VCCI-2.
More than 100Mohm at 25
C , 70% RH.
2.5 SAFETY
1.Applicable standards:
400<Vout<600V:Output is hazardous, IEEE/Isolated analog are not SELV.
2.Withstand voltage
60<Vout<600V models: Input-Haz. Output: 2.5KVrms 1min, Input-SELV: 3KVrms 1min.
Hazardous Output.-SELV: 1.9KVrms 1min, Hazardous Output-Ground:1.9KVrms 1min.
3.Insulation resistance
CE Mark, UL60950,EN60950 listed. Vout<60V:Output is SELV , IEEE/Isolated analog are SELV.
60<Vout<400V: Output is hazardous, IEEE/Isolated analog are SELV.
Vout<60V models :Input-Outputs (SELV): 3.0KVrms 1min, Input-Ground: 2.0KVrms 1min.
Input-Ground: 2KVrms 1min.
PDF 
ZIP