ChipFind - документация

Электронный компонент: MLP7130

Скачать:  PDF   ZIP
Control Devices: MLP 7100 Series
Limiter Diodes
Description
The MicroMetrics MLP 7100 series
Limiter diodes are specially processed
PIN diodes with a thin intrinsic region
designed for use in passive or active
limiters over the entire range of fre-
quencies from 100 MHz to beyond 20
GHz. The different "I" region thick-
nesses and capacitances provide vari-
able threshold and leakage power lev-
els and power handling capability.
Applications
The MLP 7100 series limiters are for
use in waveguides, coax, microstrip or
stripline. Single or cascade devices
may be used depending on power
levels.
RS
RS
RS
2
50
50
COIL for GROUND RETURN
High Power Equivalent Circuit
2
48
Features
 Low Loss
Greater Bandwidth
Fast Turn on Time
Packaging
 Chip, Glass, Ceramic, Surface Mount
Typical Performance
50
50
Diode Chip
+50
+40
+30
PEAK POWER OUTPUT
(dBm)
PEAK POWER INPUT
(dBm)
+20
+10
0
+10
+20
+30
+40
+50
+60
+66
MLP7130
MLP7110
MLP7140
MLP7100
MLP7120
50
0
+3
+6
2
4
6
8
10
12
14
16
18
+8
50
Diode Chip
MLP 7100 Series
MLP 7100-7140 Series
FREQUENCY
(GHz)
LEAKAGE POWER
ABOVE 1.0 GHz
(dB)
Contr
ol Devices
MicroMetrics, Inc. 136 Harvey Road, Building C, Londonderry, NH 03053
Voice: 603-641-3800, Fax: 603-641-3500, Internet: www.micrometrics.com, E-mail: serv@micrometrics.com
Control Devices: MLP 7100 Series
Electrical Characteristics
49
Maximum Ratings
Operating Temperature
-55C to +150C
Maximum Leakage Current
0.5 mA at 88% of minimum rated breakdown
Max. Peak
Leakage
2
Pin
Typical
Pout
Insertion Loss
3
CW
4
Recovery
5
@1.0
s
Threshold
2
TYP
TYP
Pin
Time, Typ
Part
(dBm)
(dB)
(dBm)
(dB)
MAX (W)
(nS)
Number
+50
+10
+22
0.1
2
10
MLP7100
+53
+10
+24
0.2
3
10
MLP7101
+56
+10
+25
0.2
4
10
MLP7102
+53
+15
+27
0.1
3
20
MLP7110
+56
+15
+29
0.2
4
20
MLP7111
+59
+15
+31
0.2
5
20
MLP7112
+60
+20
+39
0.1
5
50
MLP7120
+63 +20 +41 0.2 10 50 MLP7121
+66 +20 +44 0.2 15 50 MLP7122
+47
+7
+19
0.1
2
5
MLP7130
+50
+7
+22
0.1
3
5
MLP7131
+47
+12
+24
0.1
3
10
MLP7140
+50
+12
+27
0.1
4
10
MLP7141
Vb
Cj0
Cj6
Rs Typ
6
Rs Typ
6
Tl
p
1
Maximum
TYP
TYP
MAX
@ 10 mA
@ 1.0 mA
TYP
TYP
Thermal Resistance
Part
(V)
(pF)
(pF)
(
)
(
)
(nS)
(C/W)
(C/W)
Number
20-45
0.20
0.15
1.5
5.0
5
20
100
MLP7100
-
0.50
0.30
1.2
4.5
10
12
80
MLP7101
-
0.70
0.50
1.0
4.0
10
10
55
MLP7102
45-75
0.20
0.15
1.5
4.0
10
15
80
MLP7110
-
0.50
0.30
1.2
3.5
15
10
60
MLP7111
-
0.70
0.50
1.0
3.0
20
6
40
MLP7112
120-180
0.20
0.15
1.5
3.5
50
1.2
40
MLP7120
-
0.60
0.30
1.0
3.0
50
0.5
20
MLP7121
-
0.80
0.50
0.5
3.0
100
0.3
15
MLP7122
15-30
0.12
0.10
2.0
4.0
5
30
120
MLP7130
-
0.20
0.15
1.5
3.0
5
20
80
MLP7131
30-60
0.12
0.10
2.0
4.0
7
20
100
MLP7140
-
0.20
0.15
1.5
4.0
7
15
70
MLP7141
Contr
ol Devices
MicroMetrics, Inc. 136 Harvey Road, Building C, Londonderry, NH 03053
Voice: 603-641-3800, Fax: 603-641-3500, Internet: www.micrometrics.com, E-mail: serv@micrometrics.com
Notes:
1. Pulsed thermal impedance is given for a 1 s pulse. CW thermal impedance presumes infinite heat sink.
2. Threshold input power produces 1 dB increase in insertion loss. Figure shows typical leakage power curves. Data taken
for 1.0 GHz.
3. Chip loss can be represented as a resistance in shunt with the junction capacitance. Rp is measured at 3 GHz, zero
Bias. Loss data shown are for 10 GHz for 0.15 and 0.30 pF chips, 5 GHz for 0.50 pF chips. Loss is measured at -10
dBm input.
4. Note that CW power and average power are not synonymous. Power ratings are computed in terms of a peak
junction temperature of 200C, for short pulses, an average junction temperature of 125C, and an ambient of 25C.
Duty factor 0.001 assumed for maximum pulse power input. Figure shows power derating with temperature.
5. Recovery time is measured with ground return (less than 1.0 Ohm) to 1 dB excess loss, at 1 GHz.
6. Series resistance is measured at 500 MHz.
7. Limiter diodes with higher capacitance and/or higher breakdown voltage for very high power applications are
available on request.