April 2005
1
M9999-040805
MIC9130
Micrel, Inc.
MIC9130
High-Voltage, High-Speed Telecom DC-to-DC Controller
General Description
The MIC9130 is a current-mode PWM controller that efficiently
converts 48V telecom voltages to logic levels. The MIC9130
features a high voltage start-up circuit that allows the device to
be connected to input voltages as high as 180V. The high input
voltage capability protects the MIC9130 from line transients
that are common in telecom systems. The start-up circuitry
also saves valuable board space and simplifies designs by
integrating several external components.
The MIC9130 is capable of high speed operation. Typically
the MIC9130 can control a sub-25ns pulse width on the gate
out pin. Its internal oscillator can operate over 2.5MHz, with
even higher frequencies available through synchronisation.
The high speed operation of the MIC9130 is made safe by
the very fast, 34ns response from current sense to output,
minimizing power dissipation in a fault condition.
The MIC9130 allows for the designs of high efficiency power
supplies. It can achieve efficiencies over 90% at high output
currents. Its low 1.3mA quiescent current allows high efficiency
even at light loads.
The MIC9130 has a maximum duty cycle of 50%. For de-
signs requiring a high duty cycle, refer to the MIC9131. The
MIC9130 is available in a 16-pin SOP and 16-pin QSOP
package options. The rated junction temperature range is
from 40C to +125C.
Typical Application
OUT
Slope
Compensation
ISNS
FB
VBIAS
EN
SYNC
CPWR
AGND PGND
SS
UVLO
VCC
LINE
OSC
RBIAS
COMP
2
1
13
10
5
12
4
16
14
7
6
8
3
9
11
15
MIC9130
VOUT
3.3V @ 4A
VIN
36V to 72V
12V
OPTO
FEEDBACK
T1
Si4884DY
Si4800DY
B330
2.5H
330F (x2)
6.3V
FQD10N20
0.2
200V
0.2
1W
332k
47pF
4.75k
332k
10nF
0.1F
1M
38.3k
MBR0540
40V/0.5A
1F
16V
20
0.1F
1.21k
20k
N = 4
N = 20
N = 5
1.5MHz DSL Power Supply
Features
Input voltages up to 180V
Internal oscillator capable of >2.5MHz operation
Synchronisation capability to 4MHz
Current sense delay of 34ns
Minimum pulse width <25ns
90% efficiency
1.3mA quiescent current
1A shutdown current
Soft-start
Resistor programmable current sense threshold
Selectable soft-start retry
4 sink, 12 source output driver
Programmable under-voltage lockout
Constant-frequency PWM current-mode control
16-pin SOIC and 16-pin QSOP
Applications
Telecom power supplies
Line cards
ISDN network terminators
Micro- and pico-cell base stations
Low power (< 30W) dc-dc converters
Micrel, Inc. 2180 Fortune Drive San Jose, CA 95131 USA tel + 1 (408) 944-0800 fax + 1 (408) 474-1000 http://www.micrel.com
MIC9130
Micrel, Inc.
M9999-040805
2
April 2005
Pin Description
Pin Number
Pin Name
Pin Function
1
LINE
Line (Input): 180Vdc maximum supply input. May be floated if unused.
2
VCC
Supply (Input): MIC9130 internal supply input.
3
RBIAS
Bias Resistor (External Component): Connect 562K to ground.
4
OSC
Oscillator RC Network (External Components): Connect external resistor-
capacitor network to set oscillator frequency.
5
SYNC
Synchronization (Input): External oscillator input for slave operation of
controller. See OSC. Do not float.
6
COMP
Compensation (External Components): Error amplifier output for external
compensation network connection.
7
FB
Feedback (Input): Error amplifier inverting input.
8
CPWR
Current Limit Selection (Input): When CPWR is high, an over-current
condition at the ISNS input will terminate the gate drive and reset the
soft-start latch. If the CPWR pin is low, an over-current condition at the ISNS
input will terminate the gate drive signal, but will not cause a reset of the
soft-start circuit.
9
VBIAS
Reference (Output): Internal 5V supply. Will source 5mA maximum.
10
EN
Enable (Input): Logic level enable/shutdown input; logic high = enabled (on),
logic low = shutdown (off).
11
AGND
Analog Ground (Return)
12
SS
Soft-Start (External Components): Connect external capacitor to slowly ramp
up duty cycle during startup and over-current conditions.
13
UVLO
Undervoltage Lockout (External Components): Connect to unbiased resistive
divider network to set controller's minimum operating voltage. Connect to
VBIAS if not needed.
14
ISNS
Current Sense (Input): Connect between external switching MOSFET source
and switch current sense resistor.
15
PGND
Power Ground (Return)
16
OUT
Switch Drive Output (Output): Connect to gate of external switching
MOSFET.
Pin Configuration
2
VCC
3
RBIAS
4
OSC
5
SYNC
6
COMP
7
FB
1
LINE
8
CPWR
OUT
16
PGND
15
ISNS
14
UVLO
13
SS
12
AGND
11
10
9 VBIAS
EN
16-Pin SOP (M)
16-Pin QSOP (QS)
Ordering Information
Part Number
Max. Duty Cycle Junction Temp. Range
Package
Standard
Pb-Free
MIC9130BM
MIC9130YM
50%
-40C to +125C
16-Pin SOP
MIC9130BQS
MIC9130YQS
50%
-40C to +125C
16-Pin QSOP
April 2005
3
M9999-040805
MIC9130
Micrel, Inc.
Absolute Maximum Ratings
(Note 1)
Line Input Voltage (V
LINE
) .........................................+190V
V
CC
Input Voltage (V
CC
) ..............................................+19V
Current Sense Input Voltage (V
ISNS
) ..............0.3 to +5.3V
Enable Voltage (V
EN
) ............................ 0.3 to V
CC
+ 0.3V
Feedback Input Voltage (V
FB
) ........................0.3 to +5.3V
Sync Input Voltage (V
SYNC
) ............................0.3 to +5.3V
Soft-Start Voltage (V
SS
) ..................................0.3 to +5.3V
UVLO Voltage (V
UVLO
) ...................................0.3 to +5.3V
Storage Temperature (T
S
) ........................ 65C to +150C
Power Dissipation (P
D
)
16-pin SOP ...................................400mW @ T
A
= +85C
16-pin QSOP ................................245mW @ T
A
= +85C
ESD Rating,
Note 3
Operating Ratings
(Note 2)
Line Input Voltage (V
LINE
) .................V
CC
to +180V,
Note 4
V
CC
Input Voltage (V
CC
) .................................. +9V to +18V
Junction Temperature Range (T
J
) ............ 40C to +125C
Package Thermal Resistance
16-pin SOP (
JA
) ..............................................100C/W
16-pin QSOP (
JA
) ............................................163C/W
Electrical Characteristics
T
A
= 25C, V
LINE
= 48V, V
CC
= 10V, R
t
= 9.47K, C
t
= 470pF, R
BIAS
= 562k, V
EN
= 10V, V
ISNS
= 0V, V
UVLO
= 2V
,
V
SYNC
= 0V, unless
otherwise noted.
Bold values indicate 40 C T
J
+125C.
Parameter
Condition
Min
Typ
Max
Units
Bias Regulator
Output Voltage
I
VBIAS
= 0mA; V
OSC
= 0V (Oscillator OFF)
4.7
4.85
5.0
V
4.6
5.1
V
Line Regulation
9V V
CC
18V, I
VBIAS
= 0mA; V
OSC
= 0V
24
40
mV
Load Regulation
0mA I
VBIAS
5mA; V
OSC
= 0V
5
30
mV
Oscillator Section
Initial Accuracy (f
OSC
)
R
t
= 9.47K, C
t
= 470pF
180
200
220
kHz
Oscillator Output Frequency
f
OSC/2
kHz
Maximum Duty Cycle
50
%
Voltage Stability (f/f)
9V V
CC
18V
2.5
%
Temperature Stability
40C T
J
125C
100
ppm/C
Maximum Sync Frequency
Note 5
4
MHz
Sync Threshold Level
2.5
V
Sync Hysteresis
0.7
V
Sync Minimum Pulse Width
50
ns
Error Amp Section
FB Voltage
V
COMP
= V
FB
2.475
2.5
2.525
V
2.45
2.55
Open Loop Voltage Gain, A
VOL
90
dB
Unity Gain Bandwidth
4
MHz
PSRR
9V V
CC
18V
60
dB
COMP Sink Current
V
FB
= 2.7V; V
COMP
= 5V
80
100
A
COMP Source Current
V
FB
= 2.3V; V
COMP
= 0V
1
2.5
mA
V
COMP
Low
V
FB
= 2.7V; I
COMP
= 50A
115
300
mV
V
COMP
High
V
FB
= 2.3V; I
COMP
= +500A
3.5
4
V
Input Bias Current (I
FB
)
V
FB
= V
COMP
160
nA
Slew Rate
SINK
1.5
V/s
SOURCE
1.5
V/s
MIC9130
Micrel, Inc.
M9999-040805
4
April 2005
Parameter
Condition
Min
Typ
Max
Units
Preregulator
Input Leakage Current
V
LINE
= 180V, V
CC
= 10V
0.1
10
A
V
CC
Gate Lockout (V
GLO(ON)
)
V
LINE
= 48V
7.2
7.5
V
V
CC
Gate Lockout Hysteresis
V
LINE
= 48V
700
800
mV
(V
GLO
)
V
CC
Pre-Regulator Off (V
PR(OFF)
) V
LINE
= 48V
V
GLO(ON)
V
7.7
+0.5V
V
CC
Pre-Regulator Hysteresis
V
LINE
= 48V
500
700
mV
(V
PR
)
Start-up Current
V
LINE
= 48V, V
CC
= 7.5V,
Note 4
9
12
mA
Supply
Supply Current, I
VCC
Pin 16 (OUT) = OPEN
1.3
1.5
mA
Enable Input Current
V
EN
= 0V ,10V; V
LINE
= 48V
10
0.1
10
A
Shutdown Supply Current
V
EN
= 0V ; V
CC
= 18V
0.1
10
A
Protection and Control
Current Limit Threshold Voltage
0.772
0.83
0.888
V
Current Limit Delay to Output
V
ISNS
= 0V to 5V
34
ns
Current Limit Source Current
V
ISNS
= 0V
30
40
50
A
Enable Input Threshold (Turn-on)
1
1.6
2.2
V
Enable Input Hysteresis
150
mV
CPWR Input Current
V
CPWR
= 5V, 0V
1
+1
A
CPWR Threshold
1.6
V
Soft-Start Current
V
SS
= 0V
2.5
4
6
A
Line UVLO Threshold (Turn-on)
1.16
1.22
1.28
V
Line UVLO Threshold Hysteresis
140
mV
Thermal Shutdown
145
C
Thermal Shutdown Hysteresis
25
C
MOSFET Driver
Output Minimum On-Time
V
ISNS
= 5V
21
ns
Output Driver Impedance
SOURCE ; I
SOURCE
= 200mA
8
12
SINK ; I
SINK
= 200mA
4
6
Rise Time
C
OUT
= 500pF
12
ns
Fall Time
C
OUT
= 500pF
8
ns
Note 1. Exceeding the absolute maximum rating may damage the device.
Note 2. The device is not guaranteed to function outside its operating rating.
Note 3. Devices are ESD sensitive. Handling precautions recommended.
Note 4. If a substained DC voltage >150V is applied to the LINE pin, a current-limiting 1.8kresistor should be used in series with the LINE pin. This
condition does not apply for transient conditions over 150V.
Note 5. For oscillator frequencies above 2.5MHz it may be necessary to power to VBIAS pin from an external power source due to the current limita-
tions of the internal 5V regulator. See Applications Information for details
April 2005
5
M9999-040805
MIC9130
Micrel, Inc.
Typical Characteristics
-2.0
-1.5
-1.0
-0.5
0
0.5
1.0
1.5
2.0
8 9 10 11 12 13 14 15 16 17 18
OSC FREQ. VARIATION (%)
V
CC
(V)
Oscillator Frequency
vs. V
CC
Voltage
F
OSC (NOM)
=200kHz
Rt=9.47K
Ct=470pF
-5
-4
-3
-2
-1
0
1
2
3
4
5
-40
0
40
80
120
160
OSC FREQ. VARIATION (%)
TEMPERATURE (C)
Oscillator Frequency
vs. Temperature
V
C C
= 10V
R
BIAS
= 560K
Rt = 9.47K
Ct = 470pF
2.499
2.500
2.501
2.502
8 9 10 11 12 13 14 15 16 17 18
REFERENCE VOLTAGE (V)
V
CC
(V)
Error Amp Reference
Voltage vs. V
CC
Voltage
R
BIAS
= 560K
2.480
2.485
2.490
2.495
2.500
2.505
2.510
-40 -20 0 20 40 60 80 100120140
REFERENCE VOLTAGE (V)
TEMPERATURE (C)
Error Amp Reference
Voltage vs. Temperature
V
C C
= 10V
R
BIAS
= 560K
1.180
1.185
1.190
1.195
1.200
1.205
1.210
1.215
1.220
8 9 10 11 12 13 14 15 16 17 18
THRESHOLD (V)
VCC (V)
Line UVLO Threshold
vs. V
CC
1.18
1.19
1.2
1.21
1.22
1.23
1.24
-40
0
40
80
120
160
UVLO THRESHOLD (V)
TEMPERATURE (C)
Line UVLO Threshold
vs. Temperature
V
C C
=10V
R
BIAS
=560K
1.0
1.2
1.4
1.6
1.8
2.0
2.2
2.4
8
10
12
14
16
18
QUIESCENT CURRENT (mA)
V
CC
(V)
Quiescent Current
vs. V
CC
Voltage
R
BIAS
= 560K
Rt = 9.47K
Ct = 470pF
1.3
1.31
1.32
1.33
1.34
1.35
1.36
1.37
1.38
1.39
1.4
-40 -20 0 20 40 60 80 100120140
QUIESCENT CURRENT (mA)
TEMPERATURE (C)
Quiescent Current
vs. Temperature
V
C C
= 10V
R
BIAS
= 560K
Rt = 9.47K
Ct = 470pF
0
1
2
3
4
5
6
7
8
9
10
0
200
400
600
800 1000
QUIESCENT CURRENT (mA)
GATE DRIVE FREQUENCY (kHz)
Quiescent Current
vs. Frequency
Ct = 120pF
Ct = 470pF
1
1.5
2
2.5
3
3.5
0
200 400 600 800 1000 1200
QUIESCENT CURRENT (mA)
R
BIAS
(k)
Quiescent Current
vs. R
BIAS
V
C C
= 10V
Rt = 9.53K
Ct = 470pf
f
OSC
= 200kHz
0
10
20
30
40
50
60
70
80
90
0
200 400 600 800 1000 1200
DELAY (ns)
R
BIAS
(k)
ISNS to Gate Output Delay
vs. R
BIAS
0
50
100
150
200
250
300
350
0
200
400
600
800
1000
1200
1400
1600
1800
2000
DELAY (ns)
OVERDRIVE (mV)
ISNS to Gate Output Delay
vs. Overdrive
R
BIAS
=160K
R
BIAS
=560K
R
BIAS
=360K
PDF 
ZIP