August 1996
ML65244/ML65L244
*
High Speed Dual Quad Buffer/Line Drivers
BLOCK DIAGRAM
*This Part Is Obsolete
1
GENERAL DESCRIPTION
The ML65244 and ML65L244 are non-inverting dual quad
buffer/line drivers. The high operating frequency (50MHz
driving a 50pF load) and low propagation delay
(ML65244 1.7ns, ML65L244 2ns) make them ideal for
very high speed applications such as processor bus
buffering and cache and main memory control.
These buffers use a unique analog implementation to
eliminate the delays inherent in traditional digital designs.
Schottky clamps reduce under and overshoot, and special
output driver circuits limit ground bounce. The ML65244
and ML65L244 conform to the pinout and functionality of
the industry standard FCT244 and are intended for
applications where propagation delay is critical to the
system design.
Note: This part was previously numbered ML6582.
FEATURES
s Low propagation delay -- 1.7ns ML65244
2.0ns ML65L244
s Fast Dual 4-bit TTL level buffer/line driver with tri-state
capability on the output (two 4-bit sections)
s TTL compatible input and output levels
s Schottky diode clamps on all inputs to handle
undershoot and overshoot
s Onboard schottky diodes minimize noise
s Reduced output swing of 0 4.1 volts
s Ground bounce controlled outputs, typically less
than 400mV
s Industry standard FCT244 type pinout
s Applications include high speed cache memory, main
memory, processor bus buffering, and graphics cards
1G
18
YAO
17
BO
16
YA1
15
B1
14
YA2
13
B2
12
YA3
11
B3
2
AO
3
YBO
4
A1
5
YB1
6
A2
7
YB2
8
A3
9
YB3
19
1
2G
GND
10
VCC
20
VCC
2
ML65244/ML65L244
PIN CONFIGURATION
TOP VIEW
20-Pin SOIC, QSOP
PIN DESCRIPTION
NAME
I/O
DESCRIPTION
Ai
I
Data Bus A
YAi
O
Data Bus A
Bi
I
Data Bus B
YBi
O
Data Bus B
1G
I
Output Enable for data bus A
2G
I
Output Enable for data bus B
GND
I
Signal Ground
V
CC
I
+ 5V supply
FUNCTION TABLE
1G/2G
Ai/Bi
YAi/YBi
H
X
Z
L
L
L
L
H
H
1G
A0
YB0
A1
YB1
A2
YB2
A3
YB3
GND
V
CC
2G
YA0
B0
YA1
B1
YA2
B2
YA3
B3
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
ABSOLUTE MAXIMUM RATINGS
V
CC ...............................................................................
0.3V to 7V
DC Input voltage ................................ 0.3 to V
CC
+ 0.3V
AC Input voltage (< 20ns) ........................................ 3.0V
DC Output voltage ............................. 0.3 to V
CC
+ 0.3V
Output sink current (per pin) ................................ 120mA
Storage temperature ................................ 65
C to 150
C
Junction temperature .............................................. 150
C
Thermal Impedance (
JA
)
SOIC ............................................................... 96
C/W
QSOP ............................................................ 100
C/W
L = Logic Low
H = Logic High
X = Don't Care
Z = High Impedance
3
ML65244/ML65L244
ELECTRICAL CHARACTERISTICS
Unless otherwise stated, these specifications apply for: V
CC
= 5.0
5%V, T
A
= 0
C to 70
C (Note 1).
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
AC ELECTRICAL CHARACTERISTICS (C
LOAD
= 50pF, R
LOAD
= 500
)
t
PLH
, t
PHL
Propagation delay
Ai to YAi, Bi to YBi (Note 2)
ML65244
1.4
1.7
ns
ML65L244
1.6
2.0
ns
t
OE
Output enable time
10
15
ns
1G, 2G to YAi/YBi
t
OD
Output disable time
10
ns
1G, 2G to YAi/YBi
C
IN
Input capacitance
8
pF
DC ELECTRICAL CHARACTERISTICS (C
LOAD
= 50pF, R
LOAD
=
)
V
IH
Input high voltage
Logic HIGH
2.0
V
V
IL
Input low voltage
Logic LOW
0.8
V
I
IH
Input high current
Per pin, V
IN
= 3V
ML65244
0.5
1.5
mA
ML65L244
0.3
0.5
mA
I
IL
Input low current
Per pin, V
IN
= 0
ML65244
2.4
3.5
mA
ML65L244
0.8
1.0
mA
I
HI-Z
Three-state output current V
CC
= 5.25V, 0 < V
IN
< V
CC
5
A
I
OS
Short circuit current
V
CC
= 5.25V, V
O
= GND
60
225
mA
(Note 3)
V
IC
Input clamp voltage
V
CC
= 4.75V, I
IN
= 18mA
0.7
1.2
V
V
OH
Output high voltage
V
CC
= 4.75V, I
OH
= 100
A
2.4
V
(Notes 4 & 5)
V
OL
Output low voltage
V
CC
= 4.75V, I
OL
= 25mA
0.6
V
(Notes 4 & 5)
V
OFF
V
IN
V
OUT
per buffer
V
CC
= 4.75V (Note 4)
ML65244
0
100
200
mV
ML65L244
0
200
300
mV
I
CC
Quiescent Power
V
CC
= 5.25V, Freq = 0Hz,
55
80
mA
Supply Current
Inputs/outputs open
Note 1: Limits are guaranteed by 100% testing, sampling or correlation with worst case test conditions.
Note 2: One line switching, see Figure 3, t
PLH
, t
PHL
versus C
L
.
Note 3: Not more than one output should be shorted for more than a second.
Note 4: This is a true analog buffer. In the linear region, the output tracks the input with an offset (V
OFF
). For V
OH
, V
IN
= 2.7V.
V
OH MIN
includes V
OFF
. For V
OL
, V
IN
= 0V, V
OL MAX
includes V
OFF
Note 5: See Figure 2 for I
OH
versus V
OH
and I
OL
versus V
OL
data.
1.5V
1.5V
1.5V
1.5V
t
PHL
t
PLH
t
R
, t
F
4ns
3V
0V
3V
0V
INPUT
OUTPUT
4
ML65244/ML65L244
CH1 1.00V CH2 1.00V 10.0ns
CH1 1.00V CH2 1.00V 10.0ns
+20
0
20
40
60
80
100
120
140
160
180
200
2.5
I
OH
(mA)
V
OH
(V)
3.0
3.5
4.0
Figure 2a. Typical V
OL
Versus I
OL
for One Buffer Output.
Figure 2b. Typical V
OH
Versus I
OH
for One Buffer Output.
220
200
180
160
140
120
100
80
60
40
20
0
2.5
0.0
I
OL
(mA)
V
OL
(V)
0.5
1.0
1.5
2.0
3.0
2.5
2.0
1.5
1.0
0.5
0.0
100
30
t
pd
(ns)
LOAD CAPACITANCE (pF)
50
75
150
ML65L244
ML65244
210
190
170
150
130
110
90
70
50
10
I
CC
(mA)
FREQUENCY (MHz)
20
30
40
50
60
70
80
90
150pF
100pF
75pF
50pF
30pF
ML65244
74FCT244
Figure 1. Ground Bounce Comparison, Four Outputs Switching into 50pF Loads.
Figure 3. Propagation Delay (t
PLH
, t
PHL
) Versus Load
Capacitance, One Output Switching.
Figure 4. I
CC
Versus Frequency for Various Load
Capacitances, Four Outputs Switching.
5
ML65244/ML65L244
FUNCTIONAL DESCRIPTION
The ML65244 and ML65L244 are very high speed non-
inverting buffer/line drivers with three-state outputs which
are ideally suited for bus-oriented applications. They
provide a low propagation delay by using an analog
design approach (a high speed unity gain buffer), as
compared to conventional digital approaches. The
ML65244 and ML65L244 follow the pinout and
functionality of the industry standard FCT244 series of
buffer/line drivers and are intended to replace them in
designs where the propagation delay is a critical part of
the system design considerations. The ML65244 and
ML65L244 are capable of driving load capacitances
several times larger than their input capacitance. They are
configured so that the Ai inputs go to the YAi outputs, with
the A side output enable controlled by 1G. Similarly, 2G
controls the Bi inputs which go to the YBi outputs.
These unity gain analog buffers achieve low propagation
delays by having the output follow the input with a small
offset. The output rise and fall times will closely match
those of the input waveform. All inputs and outputs have
Schottky clamp diodes to handle undershoot or overshoot
noise suppression in unterminated applications. All
outputs have ground bounce suppression (typically
< 400mV), high drive output capability with almost
immediate response to the input signal, and low
output skew.
The I
OL
current drive capability of a buffer/line driver is
often interpreted as a measure of its ability to sink current
in a dynamic sense. This may be true for CMOS buffer/
line drivers, but it is not true for the ML65244 and
ML65L244. This is because their sink and source current
capability depends on the voltage difference between the
output and the input. The ML65244 can sink or source
more than 100mA to a load when the load is switching
due to the fact that during the transition, the difference
between the input and output is large. I
OL
is only
significant as a DC specification, and is 25mA.
ARCHITECTURAL DESCRIPTION
Until now, buffer/line drivers have been implemented in
CMOS logic and made to be TTL compatible by sizing the
input devices appropriately. In order to buffer large
capacitances with CMOS logic, it is necessary to cascade
an even number of inverters, each successive inverter
larger than the preceding, eventually leading to an inverter
that will drive the required load capacitance at the
required frequency. Each inverter stage represents an
additional delay in the gating process because in order for
a single gate to switch, the input must slew more than half
of the supply voltage. The best of these CMOS buffers has
managed to drive a 50pF load capacitance with a delay of
3.2ns. Micro Linear has produced a dual quad buffer/line
driver with a delay less than 1.7ns by using a unique
circuit architecture that does not require cascaded logic
gates. The ML65244 uses a feedback technique to
produce an output that follows the input. If the output
voltage is not close to the input, then the feedback
circuitry will source or sink enough current to the load
capacitance to correct the discrepancy.
Figure 5. One buffer cell of the ML65244
Q1
IN
OUT
Q2
Q7
R2
R6
R5
GND
R4
Q4
Q3
R1
R8
R3
Q5
Q6
R7
VCC
6
ML65244/ML65L244
The basic architecture of the ML65244 is shown in Figure
5. It is implemented on a 1.5
m BiCMOS process.
However, in this particular circuit, all of the active devices
are NPNs -- the fastest devices available in the process.
In this circuit, there are two paths to the output. One path
sources current to the load capacitance when the signal is
asserted, and the other path sinks current from the output
when the signal is negated.
The assertion path is the emitter follower path consisting
of the level shift transistor Q1, the output transistor Q2,
and the bias resistor R8. It sources current to the output
through the 75
resistor R7 which is bypassed by another
NPN (not shown) during fast input transients. The
negation path is a current differencing op amp connected
in a follower configuration. The active components in this
amplifier are transistors Q3Q7. R3R6 are bias resistors,
and R1 and R2 are the feedback resistors. The key to
understanding the operation of the current differencing op
amp is to know that the currents in transistors Q3 and Q5
are the same at all times and that the voltages at the bases
of Q4 and Q6 are roughly the same. If the output is higher
than the input, then an error current will flow through R2.
This error current will flow into the base of Q6 and be
multiplied by
squared to the collector of Q7, closing the
loop. The larger the discrepancy between the output and
input, the larger the feedback current, and the harder Q7
sinks current from the load capacitor.
A number of MOSFETs are not shown in Figure 5. These
MOSFETs are used to three-state dormant buffers. For
instance, the feedback resistors R1 and R2 were
implemented as resistive transmission gates to ensure that
disabled buffers do not load the lines they are connected
to. Similarly, there is a PMOS in series with R8 that is
normally on but shuts off for disable. Other MOSFETs
have been included to ensure that disabled buffers
consume no power.
TERMINATION
R7 in Figure 5 also acts as a termination resistor. This 75
resistor is in series with the output and therefore helps
suppress noise caused by transmission line effects such as
reflections from mismatched impedances. System
designers using CMOS transceivers commonly have to use
external resistors in series with each transceiver output to
suppress this noise. Systems using the ML65244 or
ML65L244 may not have to use these external resistors.
APPLICATIONS
There are a wide variety of needs for extremely fast buffers
in high speed processor system designs like Pentium,
PowerPC, Mips, Sparc, Alpha and other RISC processors.
These applications are either in the cache memory area or
the main memory (DRAM) area. In addition, fast buffers
find applications in high speed graphics and multimedia
applications. The high capacitive loading due to
multiplexed address lines on the system bus demand
external buffers to take up the excess drive current. The
needed current to skew the transitions between rise and
fall times must be done without adding excessive
propagation delay. The ML65244 and ML65L244 are
equipped with Schottky diodes to clean up ringing from
overshoot and undershoot caused by reflections in
unterminated board traces.
7
ML65244/ML65L244
PHYSICAL DIMENSIONS
inches (millimeters)
SEATING PLANE
0.291 - 0.301
(7.39 - 7.65)
PIN 1 ID
0.398 - 0.412
(10.11 - 10.47)
0.498 - 0.512
(12.65 - 13.00)
0.012 - 0.020
(0.30 - 0.51)
0.050 BSC
(1.27 BSC)
0.022 - 0.042
(0.56 - 1.07)
0.095 - 0.107
(2.41 - 2.72)
0.005 - 0.013
(0.13 - 0.33)
0.090 - 0.094
(2.28 - 2.39)
20
0.007 - 0.015
(0.18 - 0.38)
0 - 8
1
0.024 - 0.034
(0.61 - 0.86)
(4 PLACES)
Package: S20
20-Pin SOIC
PIN 1 ID
SEATING PLANE
0.150 - 0.160
(3.81 - 4.06)
0.228 - 0.244
(5.79 - 6.20)
0.338 - 0.348
(8.58 - 8.84)
0.008 - 0.012
(0.20 - 0.31)
0.025 BSC
(0.63 BSC)
0.015 - 0.035
(0.38 - 0.89)
0.060 - 0.068
(1.52 - 1.73)
0.004 - 0.010
(0.10 - 0.26)
0.055 - 0.061
(1.40 - 1.55)
0.006 - 0.010
(0.15 - 0.26)
0 - 8
20
0.050 - 0.055
(1.27 - 1.40)
(4 PLACES)
1
Package: K20
20-Pin QSOP
8
ML65244/ML65L244
ORDERING INFORMATION
PART NUMBER
SPEED
TEMPERATURE RANGE
PACKAGE
ML65244CK
1.7ns
0
C to 70
C
20-Pin QSOP (K20)
ML65244CS
1.7ns
0
C to 70
C
20-Pin SOIC (S20)
ML65L244CK
2.0ns
0
C to 70
C
20-Pin QSOP (K20)
(Obsolete)
ML65L244CS
2.0ns
0
C to 70
C
20-Pin SOIC (S20)
(Obsolete)
Intel, Pentium, PCI are registered trademarks of Intel Corporation. Mips, Alpha and Sparc are registered trademarks of Silicon Graphics, DEC and
Sun Microsystems respectively.
Micro Linear reserves the right to make changes to any product herein to improve reliability, function or design.
Micro Linear does not assume any liability arising out of the application or use of any product described herein,
neither does it convey any license under its patent right nor the rights of others. The circuits contained in this
data sheet are offered as possible applications only. Micro Linear makes no warranties or representations as to
whether the illustrated circuits infringe any intellectual property rights of others, and will accept no responsibility
or liability for use of any application herein. The customer is urged to consult with appropriate legal counsel
before deciding on a particular application.
DS65244-01
2092 Concourse Drive
San Jose, CA 95131
Tel: 408/433-5200
Fax: 408/432-0295
Micro Linear 1997
is a registered trademark of Micro Linear Corporation
Products described in this document may be covered by one or more of the following patents, U.S.: 4,897,611; 4,964,026; 5,027,116; 5,281,862; 5,283,483; 5,418,502; 5,508,570; 5,510,727; 5,523,940;
5,546,017; 5,559,470; 5,565,761; 5,592,128; 5,594,376; Japan: 2598946; 2619299. Other patents are pending.
PDF 
ZIP