ChipFind - документация

Электронный компонент: MT5VDDT872HY-202__

Скачать:  PDF   ZIP

Document Outline

09005aef80a8e767
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
1
2003 Micron Technology, Inc.
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
SMALL-OUTLINE
DDR SDRAM DIMM
MT5VDDT872H 64MB
MT5VDDT1672H 128MB
For the latest data sheet, please refer to the Micron
Web
site:
www.micron.com/moduleds
Features
JEDEC standard 200-pin, small-outline, dual in-line
memory module (DDR SODIMM)
Fast data transfer rates PC1600, PC2100, or PC2700
Utilizes 200 MT/s, 266 MT/s, and 333 MT/s DDR
SDRAM components
64MB (8 Meg x 72) and 128MB (16 Meg x 72)
ECC-1-bit error detection and correction
V
DD
= V
DD
Q= +2.5V
V
DDSPD
= +2.3V to +3.6V
2.5V I/O (SSTL_2 compatible)
Commands entered on each positive CK edge
DQS edge-aligned with data for READs; center-
aligned with data for WRITEs
Internal, pipelined double data rate (DDR)
architecture; two data accesses per clock cycle
Bidirectional data strobe (DQS) transmitted/
received with data--i.e., source-synchronous data
capture
Differential clock inputs (CK and CK#)
Four internal device banks for concurrent operation
Selectable burst lengths: 2, 4, or 8
Auto precharge option
Auto Refresh and Self Refresh Modes 15.625s
(64MB); 7.8125s (128MB) maximum average
periodic refresh interval
Serial Presence Detect (SPD) with EEPROM
Selectable READ CAS latency for maximum
compatibility
Gold edge contacts
Figure 1: 200-Pin SODIMM (MO-224)
NOTE:
1. Consult factory for availability of lead-free prod-
ucts.
2. CL = Device CAS (READ) Latency
OPTIONS
MARKING
Package
200-pin SODIMM (Standard)
G
200-pin SODIMM (Lead-free)
1
Y
Memory Clock/Speed/CAS Latency
2
6ns (167 MHz), 333 MT/s, CL = 2.5
-335
7.5ns (133 MHz), 266 MT/s, CL = 2
-262
7.5ns (133 MHz), 266 MT/s, CL = 2
-26A
7.5ns (133 MHz), 266 MT/s, CL = 2.5
-265
10ns (100 MHz), 200 MT/s, CL = 2
-202
Table 1:
Address Table
64MB
128MB
Refresh Count
4K
8K
Row Addressing
4K (A0A11)
8K(A0A12)
Device Bank Addressing
4 (BA0, BA1)
4 (BA0, BA1)
Device Configuration
8 Meg x 16
16 Meg x 16
Column Addressing
512 (A0A8)
512 (A0A8)
Module Rank Addressing
1 (S0#)
1 (S0#)
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
2
2003 Micron Technology. Inc.
NOTE:
All part numbers end with a two-place code (not shown), designating component and PCB revisions. Consult fac-
tory for current revision codes. Example: MT5VDDT1672HG-265A1.
Table 2:
Part Numbers and Timing Parameters
PART NUMBER
MODULE
DENSITY
CONFIGURATION
MODULE
BANDWIDTH
MEMORY CLOCK/
DATA RATE
CLOCK LATENCY
(CL -
t
RCD -
t
RP)
MT5VDDT872HG-335__
64MB
8 Meg x 72
2.7GB/s
6ns,333MT/s
2.5-3-3
MT5VDDT872HY-335__
64MB
8 Meg x 72
2.7GB/s
6ns,333MT/s
2.5-3-3
MT5VDDT872HG-262__
64MB
8 Meg x 72
2.1GB/s
7.5ns,266MT/s
2-2-2
MT5VDDT872HY-262__
64MB
8 Meg x 72
2.1GB/s
7.5ns,266MT/s
2-2-2
MT5VDDT872HG-26A__
64MB
8 Meg x 72
2.1GB/s
7.5ns,266MT/s
2-3-3
MT5VDDT872HY-26A__
64MB
8 Meg x 72
2.1GB/s
7.5ns,266MT/s
2-3-3
MT5VDDT872HG-265__
64MB
8 Meg x 72
2.1GB/s
7.5ns,266 MT/s
2.5-3-3
MT5VDDT872HY-265__
64MB
8 Meg x 72
2.1GB/s
7.5ns,266 MT/s
2.5-3-3
MT5VDDT872HG-202__
64MB
8 Meg x 72
1.6GB/s
10ns,200MT/s
2-2-2
MT5VDDT872HY-202__
64MB
8 Meg x 72
1.6GB/s
10ns,200MT/s
2-2-2
MT5VDDT1672HG-335__
128MB
16 Meg x 72
2.7GB/s
6ns,333MT/s
2.5-3-3
MT5VDDT1672HY-335__
128MB
16 Meg x 72
2.7GB/s
6ns,333MT/s
2.5-3-3
MT5VDDT1672HG-262__
128MB
16 Meg x 72
2.1GB/s
7.5ns,266MT/s
2-2-2
MT5VDDT1672HY-262__
128MB
16 Meg x 72
2.1GB/s
7.5ns,266MT/s
2-2-2
MT5VDDT1672HG-26A__
128MB
16 Meg x 72
2.1GB/s
7.5ns,266MT/s
2-3-3
MT5VDDT1672HY-26A__
128MB
16 Meg x 72
2.1GB/s
7.5ns,266MT/s
2-3-3
MT5VDDT1672HG-265__
128MB
16 Meg x 72
2.1GB/s
7.5ns,266 MT/s
2.5-3-3
MT5VDDT1672HY-265__
128MB
16 Meg x 72
2.1GB/s
7.5ns,266 MT/s
2.5-3-3
MT5VDDT1672HG-202__
128MB
16 Meg x 72
1.6GB/s
10ns,200MT/s
2-2-2
MT5VDDT1672HY-202__
128MB
16 Meg x 72
1.6GB/s
10ns,200MT/s
2-2-2
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
3
2003 Micron Technology. Inc.
NOTE:
Pin 99 is NC for 64MB, A12 for 128MB.
Figure 2: 200-Pin SODIMM Module Layout
Table 3:
Pin Assignment
(200-Pin SODIMM Front)
PIN SYMBOL PIN SYMBOL PIN SYMBOL PIN SYMBOL
1
V
REF
51
V
SS
101
A9
151
DQ42
3
V
SS
53
DQ19
103
V
SS
153
DQ43
5
DQ0
55
DQ24
105
A7
155
V
DD
7
DQ1
57
V
DD
107
A5
157
V
DD
9
V
DD
59
DQ25
109
A3
159
V
SS
11
DQS0
61
DQS3
111
A1
161
V
SS
13
DQ2
63
V
SS
113
V
DD
163
DQ48
15
V
SS
65
DQ26
115
A10
165
DQ49
17
DQ3
67
DQ27
117
BA0
167
V
DD
19
DQ8
69
V
DD
119
WE#
169
DQS6
21
V
DD
71
CB0
121
S0#
171
DQ50
23
DQ9
73
CB1
123
NC
173
V
SS
25
DQS1
75
V
SS
125
V
SS
175
DQ51
27
V
SS
77
DQS8
127
DQ32
177
DQ56
29
DQ10
79
CB2
129
DQ33
179
V
DD
31
DQ11
81
V
DD
131
V
DD
181
DQ57
33
V
DD
83
CB3
133
DQS4
183
DQS7
35
CK0
85
NC
135
DQ34
185
V
SS
37
CK0#
87
V
SS
137
V
SS
187
DQ58
39
V
SS
89
CK2
139
DQ35
189
DQ59
41
DQ16
91
CK2#
141
DQ40
191
V
DD
43
DQ17
93
V
DD
143
V
DD
193
SDA
45
V
DD
95
NC
145
DQ41
195
SCL
47
DQS2
97
NC
147
DQS5
197
V
DDSPD
49
DQ18
99
NC
/A12
149
V
SS
199
NC
Table 4:
Pin Assignment
(200-Pin SODIMM Back)
PIN SYMBOL PIN SYMBOL PIN SYMBOL PIN SYMBOL
2
V
REF
52
V
SS
102
A8
152
DQ46
4
V
SS
54
DQ23
104
V
SS
154
DQ47
6
DQ4
56
DQ28
106
A6
156
V
DD
8
DQ5
58
V
DD
108
A4
158
CK1#
10
V
DD
60
DQ29
110
A2
160
CK1
12
DM0
62
DM3
112
A0
162
V
SS
14
DQ6
64
V
SS
114
V
DD
164
DQ52
16
V
SS
66
DQ30
116
BA1
166
DQ53
18
DQ7
68
DQ31
118
RAS#
168
V
DD
20
DQ12
70
V
DD
120
CAS#
170
DM6
22
V
DD
72
CB4
122
NC
172
DQ54
24
DQ13
74
CB5
124
NC
174
V
SS
26
DM1
76
V
SS
126
V
SS
176
DQ55
28
V
SS
78
DM8
128
DQ36
178
DQ60
30
DQ14
80
CB6
130
DQ37
180
V
DD
32
DQ15
82
V
DD
132
V
DD
182
DQ61
34
V
DD
84
CB7
134
DM4
184
DM7
36
V
DD
86
NC
136
DQ38
186
V
SS
38
V
SS
88
V
SS
138
V
SS
188
DQ62
40
V
SS
90
V
SS
140
DQ39
190
DQ63
42
DQ20
92
V
DD
142
DQ44
192
V
DD
44
DQ21
94
V
DD
144
V
DD
194
SA0
46
V
DD
96
CKE0
146
DQ45
196
SA1
48
DM2
98
NC
148
DM5
198
SA2
50
DQ22
100
A11
150
V
SS
200
NC
U1
U2
U3
U4
U5
U6
Front View
Back View
PIN 1
PIN 199
(all odd pins)
PIN 2
PIN 200
(all even pins)
Indicates a V
DD
or V
DDQ
pin
Indicates a V
SS
pin
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
4
2003 Micron Technology. Inc.
Table 5:
Pin Descriptions
Pin numbers may not correlate with symbols. Refer to Pin Assignment Tables on page 3 for more information
PIN NUMBERS
SYMBOL
TYPE
DESCRIPTION
118, 119, 120
WE#, CAS#,
RAS#
Input
Command Inputs: RAS#, CAS#, and WE# (along with S#)
define the command being entered.
35, 37, 89, 91, 158, 160
CK0, CK0#, CK1,
CK1#, CK2, CK2#
Input
Clocks: CK and CK# are differential clock inputs. All address
and control input signals are sampled on the crossing of the
positive edge of CK and negative edge of CK#. Output data
(DQs and DQS) is refer- enced to the crossings of CK and CK#.
96
CKE0
Input
Clock Enable: CKE HIGH activates and CKE LOW deactivates
the internal clock, input buffers and output drivers. Taking
CKE LOW provides PRECHARGE POWER- DOWN and SELF
REFRESH operations (all device banks idle), or ACTIVE
POWER-DOWN (row ACTIVE in any device bank). CKE is
synchronous for POWER-DOWN entry and exit, and for SELF
REFRESH entry. CKE is asynchronous for SELF REFRESH exit
and for disabling the outputs. CKE must be maintained HIGH
throughout read and write accesses. Input buffers (excluding
CK, CK# and CKE ) are disabled during POWER-DOWN. Input
buffers (excluding CKE) are disabled during SELF REFRESH.
CKE is an SSTL_2 input but will detect an LVCMOS LOW level
after VDD is applied and until CKE is first brought HIGH.
After CKE is brought HIGH, it becomes an SSTL_2 input only.
121
S0#
Input
Chip Select: S# enables (registered LOW) and disables
(registered HIGH) the command decoder. All com- mands are
masked when S# is registered HIGH. S# is considered part of
the command code.
116, 117
BA0, BA1
Input
Bank Address: BA0 and BA1 define to which device bank an
ACTIVE, READ, WRITE, or PRECHARGE command is being
applied.
99
(128MB)
, 100, 101,
102, 105, 106, 107, 108,
109, 110, 111, 112, 115
A0-A11
(64MB)
A0-A12
(128MB)
Input
Address Inputs: Provide the row address for ACTIVE
commands, and the column address and auto precharge bit
(A10) for READ/WRITE commands, to select one location out
of the memory array in the respective device bank. A10
sampled during a PRECHARGE command determines whether
the PRECHARGE applies to one device bank (A10 LOW, device
bank selected by BA0, BA1) or all device banks (A10 HIGH).
The address inputs also provide the op-code during a MODE
REGISTER SET command. BA0 and BA1 define which mode
register (mode register or extended mode register) is loaded
during the LOAD MODE REGISTER command.
12, 26, 48, 62, 78, 134,
148, 170, 184
DM0-DM8
Input
Data Mask: DM is an input mask signal for write data. Input
data is masked when DM is sampled HIGH along with that
input data during a WRITE access. DM is sampled on both
edges of DQS. Although DM pins are input-only, the DM
loading is designed to match that of DQ and DQS pins.
193
SDA
Input/
Output
Serial Presence-Detect Data: SDA is a bidirectional pin used to
transfer addresses and data into and out of the presence-
detect portion of the module.
195
SCL
Input
Serial Clock for Presence-Detect: SCL is used to synchronize
the presence-detect data transfer to and from the module.
194, 196, 198
SA0-SA2
Input
Presence-Detect Address Inputs: These pins are used to
configure the presence-detect device.
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
5
2003 Micron Technology. Inc.
11, 25, 47, 61, 77, 133, 147,
169, 183
DQS0-DQS8
Input/
Output
Data Strobe: Output with READ data, input with WRITE data.
DQS is edge-aligned with READ data, centered in WRITE
data. Used to capture data.
71, 72, 73, 74, 79, 80, 83, 84
CB0 - CB7
Input/
Output
Check Bits: ECC 1-bit error checking and correction.
5, 6, 7, 8, 13, 14, 17, 18, 19,
20, 23, 24, 29, 30, 31, 32, 41,
42, 43, 44, 49, 50, 53, 54, 55,
56, 59, 60, 65, 66, 67, 68,
127, 128, 129, 130, 135, 136,
139, 140, 141, 142, 145, 146,
151, 152, 153, 154, 163, 164,
165, 166, 171, 172, 175, 176,
177, 178, 181, 182, 187, 188,
189, 190
DQ0-DQ63
Input/
Output
Data I/Os: Data bus.
1, 2
V
REF
Input
SSTL_2 reference voltage.
9, 10, 21, 22, 33, 34, 36,
45,46, 57, 58, 69, 70, 81, 82,
92, 93, 94, 113, 114, 131,
132, 143, 144, 155, 156, 157,
167, 168, 179, 180, 191, 192
V
DD
Supply
Power Supply: +2.5V 0.2V.
(See note 50 on page 22.)
3, 4, 15, 16, 27, 28, 38, 39,
40, 51, 52, 63, 64, 75, 76, 87,
88, 90, 103, 104, 125, 126,
137, 138, 149, 150, 159, 161,
162, 173, 174, 185, 186
V
SS
Supply
Ground.
197
V
DDSPD
Supply
Serial EEPROM positive power supply: +2.3V to +3.6V.
85, 86, 95, 97, 98,
99 (64MB), 123, 122, 124,
199, 200
NC
No Connect: These pins should be left unconnected.
Table 5:
Pin Descriptions
Pin numbers may not correlate with symbols. Refer to Pin Assignment Tables on page 3 for more information
PIN NUMBERS
SYMBOL
TYPE
DESCRIPTION
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
6
2003 Micron Technology. Inc.
Figure 3: Functional Block Diagram
DM3
DM2
DQ0
DQ1
DQ2
DQ3
DM0
DQ4
DQ5
DQ6
DQ7
DQ8
DQ9
DQ10
DQ11
DQ
DQ
DQ
DQ
U1
DQ12
DQ13
DQ14
DQ15
DQ
DQ
DQ
DQ
DQ16
DQ17
DQ18
DQ19
DQ20
DQ21
DQ22
DQ23
DQ24
DQ25
DQ26
DQ27
U2
DQ28
DQ29
DQ30
DQ31
DQ40
DQ41
DQ42
DQ43
U3
DM4
DQ44
DQ45
DQ46
DQ47
DQ48
DQ49
DQ50
DQ51
DQ52
DQ53
DQ54
DQ55
DQ56
DQ57
DQ58
DQ59
U4
DQ60
DQ61
DQ62
DQ63
DM1
DQ32
DQ33
DQ34
DQ35
DQ36
DQ37
DQ38
DQ39
DM5
DM6
DM7
S0#
S0#
S0#
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
LDM
UDM
S0#
BA0-BA1
A0-A11(64MB)
RAS#
CAS#
WE#
CKE0
DDR SDRAMs
CK0
CK1
DDR SDRAMs U1, U2
DDR SDRAMs U3, U4
DQS0
UDQS
DQS1
LDQS
DQS2
DQS3
DQS7
DQS6
DQS5
DQS4
CK1#
CK0#
DDR SDRAMs
DDR SDRAMs
DDR SDRAMs
DDR SDRAMs
DDR SDRAMs
S0#
A0
SA0
SERIAL PD
SDA
A1
SA1
A2
SA2
WP
SCL
U6
V
REF
V
SS
DDR SDRAMs
DDR SDRAMs
V
DD
DDR SDRAMs
V
DDSPD
SPD
A0-A12(128MB)
DDR SDRAMs
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
LDM
UDM
UDQS
LDQS
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
LDM
UDM
UDQS
LDQS
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
LDM
UDM
UDQS
LDQS
NC
NC
NC
NC
NC
NC
NC
NC
U5
V
DD
DM8
S0#
DQS8
V
DD
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
DQ
LDM
UDM
UDQS
LDQS
CB0
CB1
CB2
CB3
CB4
CB5
CB6
CB7
CK2
CK2#
DDR SDRAM U5
47K
47K
120
6.6pF
120
6.6pF
120
6.6pF
NOTE:
1.
Unless otherwise stated, all resistors are 22
W.
2.
Per industry standard, Micron utilizes various component speed grades as
referenced in the Module Part Numbering Guide at
www.micron.com/
numberguide
.
DDR SDRAM = MT46V8M16TG for 64MB
DDR SDRAM = MT46V16M16TG 128MB
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
7
2003 Micron Technology. Inc.
General Description
The MT5VDDT872H and MT5VDDT1672H are
high-speed CMOS, dynamic random-access, 64MB
and 128MB memory modules organized in a x72 (ECC)
configuration. DDR SDRAM modules use internally
configured quad-bank DDR SDRAM devices.
DDR SDRAM modules use a double data rate archi-
tecture to achieve high-speed operation. The double
data rate architecture is essentially a 2n-prefetch
architecture with an interface designed to transfer two
data words per clock cycle at the I/O pins. A single
read or write access for DDR SDRAM modules effec-
tively consists of a single 2n-bit wide, one-clock-cycle
data transfer at the internal DRAM core and two corre-
sponding n-bit wide, one-half-clock-cycle data trans-
fers at the I/O pins.
A bidirectional data strobe (DQS) is transmitted
externally, along with data, for use in data capture at
the receiver. DQS is an intermittent strobe transmitted
by the DDR SDRAM during READs and by the memory
controller during WRITEs. DQS is edge-aligned with
data for READs and center-aligned with data for
WRITEs.
DDR SDRAM modules operate from differential
clocks (CK, CK#); the crossing of CK going HIGH and
CK# going LOW will be referred to as the positive edge
of CK. Commands (address and control signals) are
registered at every positive edge of CK. Input data is
registered on both edges of DQS, and output data is
referenced to both edges of DQS, as well as to both
edges of CK.
Read and write accesses to DDR SDRAM modules
are burst oriented; accesses start at a selected location
and continue for a programmed number of locations
in a programmed sequence. Accesses begin with the
registration of an ACTIVE command, which is then fol-
lowed by a READ or WRITE command. The address
bits registered coincident with the ACTIVE command
are used to select the device bank and row to be
accessed (BA0, BA1 select device bank; A0A11 select
device row for 64MB, A0A12 select device row for
128MB ). The address bits registered coincident with
the READ or WRITE command are used to select the
device bank and the starting device column location
for the burst access.
DDR SDRAM modules provide for programmable
read or write burst lengths of 2, 4, or 8 locations. An
auto precharge function may be enabled to provide a
self-timed row precharge that is initiated at the end of
the burst access.
The pipelined, multibank architecture of DDR
SDRAM modules allows for concurrent operation,
thereby providing high effective bandwidth by hiding
row precharge and activation time.
An auto refresh mode is provided, along with a
power-saving power-down mode. All inputs are com-
patible with the JEDEC Standard for SSTL_2. All out-
puts are SSTL_2, Class II compatible. For more
information regarding DDR SDRAM operation, refer to
the 128Mb and 256Mb DDR SDRAM component data
sheets.
Serial Presence- Detect Operation
DDR SDRAM modules incorporate serial presence-
detect (SPD). The SPD function is implemented using
a 2,048-bit EEPROM. This nonvolatile storage device
contains 256 bytes. The first 128 bytes can be pro-
grammed by Micron to identify the module type and
various SDRAM organizations and timing parameters.
The remaining 128 bytes of storage are available for
use by the customer. System READ/WRITE operations
between the master (system logic) and the slave
EEPROM device (DIMM) occur via a standard I
2
C bus
using the DIMM's SCL (clock) and SDA (data) signals,
together with SA(2:0), which provide eight unique
DIMM/EEPROM addresses. Write protect (WP) is tied
to ground on the module, permanently disabling hard-
ware write protect.
Mode Register Definition
The mode register is used to define the specific
mode of operation of the DDR SDRAM. This definition
includes the selection of a burst length, a burst type, a
CAS latency and an operating mode, as shown in the
Mode Register Diagram. The mode register is pro-
grammed via the MODE REGISTER SET command
(with BA0 = 0 and BA1 = 0) and will retain the stored
information until it is programmed again or the device
loses power (except for bit A8, which is self-clearing).
Reprogramming the mode register will not alter the
contents of the memory, provided it is performed cor-
rectly. The mode register must be loaded (reloaded)
when all device banks are idle and no bursts are in
progress, and the controller must wait the specified
time before initiating the subsequent operation. Vio-
lating either of these requirements will result in
unspecified operation.
Mode register bits A0A2 specify the burst length,
A3 specifies the type of burst (sequential or inter-
leaved), A4A6 specify the CAS latency, and A7A11
(64MB), or A7A12 (128MB) specify the operating
mode.
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
8
2003 Micron Technology. Inc.
Burst Length
Read and write accesses to the DDR SDRAM are
burst oriented, with the burst length being program-
mable, as shown in Mode Register Diagram. The burst
length determines the maximum number of column
locations that can be accessed for a given READ or
WRITE command. Burst lengths of 2, 4, or 8 locations
are available for both the sequential and the inter-
leaved burst types.
Reserved states should not be used, as unknown
operation or incompatibility with future versions may
result.
When a READ or WRITE command is issued, a block
of columns equal to the burst length is effectively
selected. All accesses for that burst take place within
this block, meaning that the burst will wrap within the
block if a boundary is reached. The block is uniquely
selected by A1Ai when the burst length is set to two,
by A2Ai when the burst length is set to four and by
A3Ai when the burst length is set to eight (where Ai is
the most significant column address bit for a given
configuration; see Note 5 for Figure 6, Burst Definition
Table, on page 9). The remaining (least significant)
address bit(s) is (are) used to select the starting loca-
tion within the block. The programmed burst length
applies to both read and write bursts.
Burst Type
Accesses within a given burst may be programmed
to be either sequential or interleaved; this is referred to
as the burst type and is selected via bit M3.
The ordering of accesses within a burst is deter-
mined by the burst length, the burst type and the start-
ing column address, as shown in Burst Definition
Table.
Read Latency
The READ latency is the delay, in clock cycles,
between the registration of a READ command and the
availability of the first bit of output data. The latency
can be set to 2 or 2.5 clocks, as shown in CAS Latency
Diagram.
If a READ command is registered at clock edge n,
and the latency is m clocks, the data will be available
nominally coincident with clock edge n + m. The CAS
Latency Table indicates the operating frequencies at
which each CAS latency setting can be used.
Reserved states should not be used as unknown
operation or incompatibility with future versions may
result.
Figure 4: Mode Register Definition Diagram
M3 = 0
Reserved
2
4
8
Reserved
Reserved
Reserved
Reserved
M3 = 1
Reserved
2
4
8
Reserved
Reserved
Reserved
Reserved
Operating Mode
Normal Operation
Normal Operation/Reset DLL
All other states reserved
0
1
-
0
0
-
0
0
-
0
0
-
0
0
-
0
0
-
Valid
Valid
-
0
1
Burst Type
Sequential
Interleaved
CAS Latency
Reserved
Reserved
2
Reserved
Reserved
Reserved
2.5
Reserved
Burst Length
M0
0
1
0
1
0
1
0
1
Burst Length
CAS Latency BT
0*
A9
A7 A6 A5 A4 A3
A8
A2 A1 A0
Mode Register (Mx)
Address Bus
9
7
6
5
4
3
8
2
1
0
M1
0
0
1
1
0
0
1
1
M2
0
0
0
0
1
1
1
1
M3
M4
0
1
0
1
0
1
0
1
M5
0
0
1
1
0
0
1
1
M6
0
0
0
0
1
1
1
1
M6-M0
M8 M7
Operating Mode
A10
A12 A11
BA0
BA1
10
11
12
13
0*
14
* M14 and M13 (BA1 and BA0)
must be "0, 0" to select the
base mode register (vs. the
extended mode register).
M9
M10
M12 M11
Burst Length
CAS Latency BT
0*
0*
A9
A7 A6 A5 A4 A3
A8
A2 A1 A0
Mode Register (Mx)
Address Bus
9
7
6
5
4
3
8
2
1
0
Operating Mode
A10
A11
BA0
BA1
10
11
12
13
* M13 and M12 (BA1 and BA0)
must be "0, 0" to select the
base mode register (vs. the
extended mode register).
64MB Module
128MB Module
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
9
2003 Micron Technology. Inc.
NOTE:
1. For a burst length of two, A1
Ai select the two-data-
element block; A0 selects the first access within the
block.
2. For a burst length of four, A2
Ai select the four-data-
element block; A0
A1 select the first access within the
block.
3. For a burst length of eight, A3
Ai select the eight-data-
element block; A0
A2 select the first access within the
block.
4. Whenever a boundary of the block is reached within a
given sequence above, the following access wraps
within the block.
5. Ai = A8
Figure 5: CAS Latency Diagram
Operating Mode
The normal operating mode is selected by issuing a
MODE REGISTER SET command with bits A7A11
(64MB) or A7A12 (128MB) each set to zero, and bits
A0A6 set to the desired values. A DLL reset is initiated
by issuing a MODE REGISTER SET command with bits
A7 and A9A11 (64MB) or A9A12 (128MB) each set to
zero, bit A8 set to one, and bits A0A6 set to the desired
values. Although not required by the Micron device,
JEDEC specifications recommend when a LOAD
MODE REGISTER command is issued to reset the DLL,
it should always be followed by a LOAD MODE REGIS-
TER command to select normal operating mode.
All other combinations of values for A7A11 (64MB)
or A7A12 (128MB) are reserved for future use and/or
test modes. Test modes and reserved states should not
be used because unknown operation or incompatibil-
ity with future versions may result.
Extended Mode Register
The extended mode register controls functions
beyond those controlled by the mode register; these
additional functions are DLL enable/disable and out-
put drive strength. These functions are controlled via
the bits shown in the Extended Mode Register Defini-
tion Diagram. The extended mode register is pro-
grammed via the LOAD MODE REGISTER command
Table 6:
Burst Definition Table
BURST
LENGTH
STARTING
COLUMN
ADDRESS
ORDER OF ACCESSES
WITHIN A BURST
TYPE =
SEQUENTIAL
TYPE =
INTERLEAVED
2
A0
0
0-1
0-1
1
1-0
1-0
4
A1 A0
0
0
0-1-2-3
0-1-2-3
0
1
1-2-3-0
1-0-3-2
1
0
2-3-0-1
2-3-0-1
1
1
3-0-1-2
3-2-1-0
8
A2 A1 A0
0
0
0
0-1-2-3-4-5-6-7
0-1-2-3-4-5-6-7
0
0
1
1-2-3-4-5-6-7-0
1-0-3-2-5-4-7-6
0
1
0
2-3-4-5-6-7-0-1
2-3-0-1-6-7-4-5
0
1
1
3-4-5-6-7-0-1-2
3-2-1-0-7-6-5-4
1
0
0
4-5-6-7-0-1-2-3
4-5-6-7-0-1-2-3
1
0
1
5-6-7-0-1-2-3-4
5-4-7-6-1-0-3-2
1
1
0
6-7-0-1-2-3-4-5
6-7-4-5-2-3-0-1
1
1
1
7-0-1-2-3-4-5-6
7-6-5-4-3-2-1-0
Table 7:
CAS Latency (CL) Table
ALLOWABLE OPERATING
CLOCK FREQUENCY (MHZ)
SPEED
CL = 2
CL = 2.5
-335
NA
75
f 167
-262
75
f 133
75
f 133
-26A
75
f 133
75
f 133
-265
75
f 100
75
f 133
-202
75
f 100
75
f 125
CK
CK#
COMMAND
DQ
DQS
CL = 2
READ
NOP
NOP
NOP
READ
NOP
NOP
NOP
Burst Length = 4 in the cases shown
Shown with nominal tAC, tDQSCK, and tDQSQ
CK
CK#
COMMAND
DQ
DQS
CL = 2.5
T0
T1
T2
T2n
T3
T3n
T0
T1
T2
T2n
T3
T3n
DON'T CARE
TRANSITIONING DATA
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
10
2003 Micron Technology. Inc.
to the mode register (with BA0 = 1 and BA1 = 0) and
will retain the stored information until it is pro-
grammed again or the device loses power. The
enabling of the DLL should always be followed by a
LOAD MODE REGISTER command to the mode regis-
ter (BA0/BA1 both low) to reset the DLL.
The extended mode register must be loaded when
all device banks are idle and no bursts are in progress,
and the controller must wait the specified time before
initiating any subsequent operation. Violating either
of these requirements could result in unspecified oper-
ation.
Output Drive Strength
The normal full drive strength for all outputs is
specified to be SSTL2, Class II. The x16 supports an
option for reduced drive. This option is intended for
the support of the lighter load and/or point-to-point
environments.
The selection of the reduced drive strength will alter
the DQ and DQS from SSTL2, Class II drive strength to
a reduced drive strength, which is approximately 54
percent of the SSTL2, Class II drive strength.
For detailed information on programmable and
reduced drive strength option, refer to the 128Mb or
256Mb DDR SDRAM data sheets.
DLL Enable/Disable
The DLL must be enabled for normal operation.
DLL enable is required during power-up initialization
and upon returning to normal operation after having
disabled the DLL for the purpose of debug or evalua-
tion. (When the device exits self refresh mode, the DLL
is enabled automatically.) Any time the DLL is
enabled, 200 clock cycles must occur before a READ
command can be issued.
Figure 6: Extended Mode Register
Definition Diagram
NOTE:
1. BA1 and BA0 (E13 and E12 for 64MB, E14 and E13
for 128MB) must be "0, 1" to select the Extended
Mode Register (vs. the base Mode Register).
2. The QFC# option is not supported.
Operating Mode
Normal Operation
All other states reserved
0
0
Valid
0
1
DLL
Enable
Disable
DLL
1
1
0
1
A9
A7 A6 A5 A4 A3
A8
A2 A1 A0
Extended Mode
Register (Ex)
Address Bus
9
7
6
5
4
3
8
2
1
0
E0
0
1
Drive Strength
Normal
Reduced
E1
E0
E1,
Operating Mode
A10
A11
BA1 BA0
10
11
12
13
E3
E4
0
0
0
0
0
E6 E5
E7
E8
E9
0
0
E10
E11
DS
DLL
1
1
0
1
A9
A7 A6 A5 A4 A3
A8
A2 A1 A0
Extended Mode
Register (Ex)
Address Bus
9
7
6
5
4
3
8
2
1
0
Operating Mode
A10
A11
A12
BA1 BA0
10
11
12
13
14
DS
64MB Module
128MB Module
0
E2
2
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
11
2003 Micron Technology. Inc.
Commands
The Truth Tables below provides a general reference
of available commands. For a more detailed descrip-
tion of commands and operations, refer to the 128Mb
or 256Mb DDR SDRAM component data sheet.
NOTE:
1. DESELECT and NOP are functionally interchangeable.
2. BA0BA1 provide device bank address and A0A11 (64MB) or A0A12 (128MB) provide row address.
3. BA0BA1 provide device bank address; A0A8, provide column address; A10 HIGH enables the auto precharge feature
(nonpersistent), and A10 LOW disables the auto precharge feature.
4. Applies only to read bursts with auto precharge disabled; this command is undefined (and should not be used) for READ
bursts with auto precharge enabled and for WRITE bursts.
5. A10 LOW: BA0BA1 determine which device bank is precharged. A10 HIGH: all device banks are precharged and BA0-
BA1 are "Don't Care."
6. This command is AUTO REFRESH if CKE is HIGH, SELF REFRESH if CKE is LOW.
7. Internal refresh counter controls row addressing; all inputs and I/Os are "Don't Care" except for CKE.
8. BA0BA1 select either the mode register or the extended mode register (BA0 = 0, BA1 = 0 select the mode register; BA0
= 1, BA1 = 0 select extended mode register; other combinations of BA0BA1 are reserved).
A0A11 (64MB) or A0A12 (128MB) provide the op-code to be written to the selected mode register.
Table 8:
Truth Table Commands
CKE is HIGH for all commands shown except SELF REFRESH
NAME (FUNCTION)
CS#
RAS#
CAS#
WE#
ADDR
NOTES
DESELECT (NOP)
H
X
X
X
X
1
NO OPERATION (NOP)
L
H
H
H
X
1
ACTIVE (Select device bank and activate row)
L
L
H
H
Bank/Row
2
READ (Select device bank and column, and start READ burst)
L
H
L
H
Bank/Col
3
WRITE (Select device bank and column, and start WRITE burst)
L
H
L
L
Bank/Col
3
BURST TERMINATE
L
H
H
L
X
4
PRECHARGE (Deactivate row in device bank or banks)
L
L
H
L
Code
5
AUTO REFRESH or SELF REFRESH (Enter self refresh mode)
L
L
L
H
X
6, 7
LOAD MODE REGISTER
L
L
L
L
Op-Code
8
Table 9:
Truth Table DM Operation
Used to mask write data; provided coincident with the corresponding data
NAME (FUNCTION)
DM
DQS
WRITE Enable
L
Valid
WRITE Inhibit
H
X
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
12
2003 Micron Technology. Inc.
Absolute Maximum Ratings
Stresses greater than those listed may cause perma-
nent damage to the device. This is a stress rating only,
and functional operation of the device at these or any
other conditions above those indicated in the opera-
tional sections of this specification is not implied.
Exposure to absolute maximum rating conditions for
extended periods may affect reliability.
Voltage on V
DD
Supply
Relative to V
SS
. . . . . . . . . . . . . . . . . . . . . -1V to +3.6V
Voltage on V
DD
Q Supply
Relative to V
SS
. . . . . . . . . . . . . . . . . . . . -1V to +3.6V
Voltage on V
REF
and Inputs
Relative to V
SS
. . . . . . . . . . . . . . . . . . . . -1V to +3.6V
Voltage on I/O Pins
Relative to V
SS
. . . . . . . . . . . . . -0.5V to V
DD
Q +0.5V
Operating Temperature
T
A
(ambient) . . . . . . . . . . . . . . . . . . . .. 0C to +70C
Storage Temperature (plastic) . . . . . . -55C to +150C
Power Dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . 5W
Short Circuit Output Current. . . . . . . . . . . . . . . 50mA
Table 10: DC Electrical Characteristics and Operating Conditions
Notes: 15, 14, 50; notes appear on pages 1922; 0C
T
A
+70C
PARAMETER/CONDITION
SYMBOL
MIN
MAX
UNITS
NOTES
Supply Voltage
V
DD
2.3
2.7
V
32, 37
I/O Supply Voltage
V
DD
Q
2.3
2.7
V
32, 37, 40
I/O Reference Voltage
V
REF
0.49
V
DD
Q 0.51
V
DD
Q
V
6, 40
I/O Termination Voltage (system)
V
TT
V
REF
- 0.04
V
REF
+ 0.04
V
7, 40
Input High (Logic 1) Voltage
V
IH
(
DC
)
V
REF
+ 0.15
V
DD
+ 0.3
V
25
Input Low (Logic 0) Voltage
V
IL
(
DC
)
-0.3
V
REF
- 0.15
V
25
INPUT LEAKAGE CURRENT Any input
0V
V
IN
V
DD
, Vref pin 0V
V
IN
1.35V
(All other pins not under test = 0V)
Command/Address,
RAS#, CAS#, WE#,
CKE, S#
I
I
-10
10
A
49
CK0, CK0#, CK1, CK1#
-4
4
DM, CK2, CK2#
-2
2
OUTPUT LEAKAGE CURRENT
(DQ pins are disabled; 0V
V
OUT
V
DD
Q)
DQ, DQS
I
OZ
-5
5
A
49
OUTPUT LEVELS
High Current (V
OUT
= V
DD
Q - 0.373V, minimum V
REF
, minimum V
TT
)
Low Current (V
OUT
= 0.373V, maximum V
REF
, maximum V
TT
)
I
OH
-16.8
mA
33, 35
I
OL
16.8
mA
OUTPUT LEVELS (Reduced drive option)
High Current (V
OUT
= V
DD
Q - 0.373V, minimum V
REF
, minimum V
TT
)
Low Current (V
OUT
= 0.373V, maximum V
REF
, maximum V
TT
)
I
OH
-9
mA
34, 35
I
OL
9
mA
Table 11: AC Input Operating Conditions
Notes: 15, 14, 50; notes appear on pages 1922; 0C
T
A
+70C; V
DD
= V
DD
Q = +2.5V 0.2V
PARAMETER/CONDITION
SYMBOL
MIN
MAX
UNITS
NOTES
Input High (Logic 1) Voltage
V
IH
(
AC
)
V
REF
+ 0.310
V
12, 25, 36
Input Low (Logic 0) Voltage
V
IL
(
AC
)
V
REF
- 0.310
V
12, 25, 36
I/O Reference Voltage
V
REF
(
AC
)
0.49
V
DD
Q
0.51
V
DD
Q
V
6
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
13
2003 Micron Technology. Inc.
Table 12: I
DD
Specifications and Conditions 64MB Module
DDR SDRAM component values only
Notes: 15, 8, 10, 14, 50; notes appear on pages 1922; 0C
T
A
+70C; V
DD
= V
DD
Q = +2.5V 0.2V
MAX
PARAMETER/CONDITION
SYM
-335
-262
-26A/
-265
-202
UNITS NOTES
OPERATING CURRENT: One device bank; Active-Precharge;
t
RC =
t
RC (MIN);
t
CK =
t
CK (MIN); DQ, DM and DQS inputs
changing once per clock cyle; Address and control inputs
changing once every two clock cycles
I
DD0
600
575
550
525
mA
20, 44
OPERATING CURRENT: One device bank; Active -Read
Precharge; Burst = 2;
t
RC =
t
RC (MIN);
t
CK =
t
CK (MIN);
I
OUT
= 0mA; Address and control inputs changing once per
clock cycle
I
DD1
675
675
650
600
mA
20, 44
PRECHARGE POWER-DOWN STANDBY CURRENT: All device
banks idle; Power-down mode;
t
CK =
t
CK (MIN); CKE = (LOW)
I
DD2P
15
15
15
15
mA
21, 28,
46
IDLE STANDBY CURRENT: CS# = HIGH; All device banks idle;
t
CK =
t
CK MIN; CKE = HIGH; Address and other control inputs
changing once per clock cycle. V
IN
= V
REF
for DQ, DQS, and
DM
I
DD2F
225
225
225
175
mA
47
ACTIVE POWER-DOWN STANDBY CURRENT: One device bank
active; Power-down mode;
t
CK =
t
CK (MIN); CKE = LOW
I
DD3P
125
125
100
100
mA
21, 28,
46
ACTIVE STANDBY CURRENT: CS# = HIGH; CKE = HIGH; One
device bank; Active-Precharge;
t
RC =
t
RAS (MAX);
t
CK =
t
CK (MIN); DQ, DM andDQS inputs changing twice per
clock cycle; Address and other control inputs changing once
per clock cycle
I
DD3N
250
250
225
200
mA
20, 43
OPERATING CURRENT: Burst = 2; Reads; Continuous burst;
One device bank active; Address and control inputs changing
once per clock cycle;
t
CK =
t
CK (MIN); I
OUT
= 0mA
I
DD4R
750
725
725
675
mA
20, 44
OPERATING CURRENT: Burst = 2; Writes; Continuous burst;
One device bank active; Address and control inputs changing
once per clock cycle;
t
CK =
t
CK (MIN); DQ, DM, and DQS
inputs changing twice per clock cycle
I
DD4W
700
675
625
575
mA
20
AUTO REFRESH CURRENT
t
RC =
t
RC (MIN)
I
DD5
1,175
1,075
1,050
950
mA
24, 46
t
RC = 15.625s
I
DD5A
25
25
25
25
mA
24, 46
SELF REFRESH CURRENT: CKE
0.2V
I
DD6
15
15
10
10
mA
9
OPERATING CURRENT: Four device bank interleaving READs
(BL = 4) with auto precharge,
t
RC =
t
RC (MIN);
t
CK =
t
CK
(MIN); Address and control inputs change only during Active
READ or WRITE commands
I
DD7
1,800
1,800
1,675
1,550
mA
20, 45
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
14
2003 Micron Technology. Inc.
Table 13: I
DD
Specifications and Conditions 128MB Module
DDR SDRAM component values only
Notes: 15, 8, 10, 14, 50; notes appear on pages 1922; 0C
T
A
+70C; V
DD
= V
DD
Q = +2.5V 0.2V
MAX
PARAMETER/CONDITION
SYM
-335
-262
-26A/
-265
-202
UNITS NOTES
OPERATING CURRENT: One device bank; Active-Precharge;
t
RC =
t
RC (MIN);
t
CK =
t
CK (MIN); DQ, DM and DQS inputs
changing once per clock cyle; Address and control inputs
changing once every two clock cycles
I
DD0
625
625
525
600
mA
20, 44
OPERATING CURRENT: One device bank; Active -Read
Precharge; Burst = 2;
t
RC =
t
RC (MIN);
t
CK =
t
CK (MIN);
I
OUT
= 0mA; Address and control inputs changing once per
clock cycle
I
DD1
900
850
775
825
mA
20, 44
PRECHARGE POWER-DOWN STANDBY CURRENT: All device
banks idle; Power-down mode;
t
CK =
t
CK (MIN); CKE = (LOW)
I
DD2P
20
20
20
20
mA
21, 28,
46
IDLE STANDBY CURRENT: CS# = HIGH; All device banks idle;
t
CK =
t
CK MIN; CKE = HIGH; Address and other control inputs
changing once per clock cycle. V
IN
= V
REF
for DQ, DQS, and
DM
I
DD2F
250
225
225
225
mA
47
ACTIVE POWER-DOWN STANDBY CURRENT: One device bank
active; Power-down mode;
t
CK =
t
CK (MIN); CKE = LOW
I
DD3P
150
125
125
150
mA
21, 28,
46
ACTIVE STANDBY CURRENT: CS# = HIGH; CKE = HIGH; One
device bank; Active-Precharge;
t
RC =
t
RAS (MAX);
t
CK =
t
CK (MIN); DQ, DM andDQS inputs changing twice per
clock cycle; Address and other control inputs changing once
per clock cycle
I
DD3N
300
250
250
250
mA
20, 43
OPERATING CURRENT: Burst = 2; Reads; Continuous burst;
One device bank active; Address and control inputs changing
once per clock cycle;
t
CK =
t
CK (MIN); I
OUT
= 0mA
I
DD4R
1,100
925
925
1250
mA
20, 44
OPERATING CURRENT: Burst = 2; Writes; Continuous burst;
One device bank active; Address and control inputs changing
once per clock cycle;
t
CK =
t
CK (MIN); DQ, DM, and DQS
inputs changing twice per clock cycle
I
DD4W
825
725
725
1,250
mA
20
AUTO REFRESH CURRENT
t
RC =
t
RC (MIN)
I
DD5
1,275
1,175
1,175
1,225
mA
24, 46
t
RC = 7.8125s
I
DD5A
30
30
30
30
mA
24, 46
SELF REFRESH CURRENT: CKE
0.2V
I
DD6
20
20
20
20
mA
9
OPERATING CURRENT: Four device bank interleaving READs
(BL = 4) with auto precharge,
t
RC =
t
RC (MIN);
t
CK =
t
CK
(MIN); Address and control inputs change only during Active
READ or WRITE commands
I
DD7
2,200
1,900
1,900
2,000
mA
20, 45
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
15
2003 Micron Technology. Inc.
Table 14: Capacitance
Note: 11; notes appearon pages 1922
PARAMETER
SYMBOL
MIN
MAX
UNITS
Input/Output Capacitance: DQ, DQS
C
IO
4
5
pF
Input Capacitance: Command and Address, S#, CKE
C
I1
10
15
pF
Input Capacitance: CK0, CK0#, CK1, CK1#
C
I2
10.6
12.6
pF
Input Capacitance: CK2, CK2#
C
I2
8.6
9.6
pF
Table 15: DDR SDRAM Component Electrical Characteristics and Recommended AC
Operating Conditions (-335, -262)
Notes: 15, 12-15, 29, 50; notes appear on pages 1922; 0C
T
A
+70C; V
DD
= V
DD
Q = +2.5V 0.2V
AC CHARACTERISTICS
-335
-262
UNITS
NOTES
PARAMETER
SYMBOL
MIN
MAX
MIN
MAX
Access window of DQs from CK/CK#
t
AC
-0.7
+0.75
-0.70
+0.70
ns
CK high-level width
t
CH
0.45
0.55
0.45
0.55
t
CK
26
CK low-level width
t
CL
0.45
0.55
0.45
0.55
t
CK
26
Clock cycle time
CL=2.5
t
CK (2.5)
6
13
6
13
ns
41, 48
CL=2
t
CK (2)
7.5
13
7.5
13
ns
41, 48
DQ and DM input hold time relative to DQS
t
DH
0.45
0.45
ns
23, 27
DQ and DM input setup time relative to DQS
t
DS
0.45
0.45
ns
23, 27
DQ and DM input pulse width (for each input)
t
DIPW
1.75
1.75
ns
27
Access window of DQS from CK/CK#
t
DQSCK
-0.60
+0.60
-0.65
+0.6
ns
DQS input high pulse width
t
DQSH
0.35
0.35
t
CK
DQS input low pulse width
t
DQSL
0.35
0.35
t
CK
DQS-DQ skew, DQS to last DQ valid, per group, per access
t
DQSQ
0.45
0.45
ns
22, 23
Write command to first DQS latching transition
t
DQSS
0.75
1.25
0.75
1.25
t
CK
DQS falling edge to CK rising - setup time
t
DSS
0.2
0.2
t
CK
DQS falling edge from CK rising - hold time
t
DSH
0.2
0.2
t
CK
Half clock period
t
HP
t
CH,
t
CL
t
CH,
t
CL
ns
30
Data-out high-impedance window from CK/CK#
t
HZ
+0.70
+0.7
ns
16, 38
Data-out low-impedance window from CK/CK#
t
LZ
-0.70
-0.7
ns
16, 39
Address and control input hold time (fast slew rate)
t
IH
F
0.75
0.75
ns
12
Address and control input setup time (fast slew rate)
t
IS
F
0.75
0.75
ns
12
Address and control input hold time (slow slew rate)
t
IH
S
0.80
0.8
ns
12
Address and control input setup time (slow slew rate)
t
IS
S
0.80
0.8
ns
12
LOAD MODE REGISTER command cycle time
t
MRD
12
15
ns
DQ-DQS hold, DQS to first DQ to go non-valid, per access
t
QH
t
HP -
t
QHS
t
HP-
t
QHS
ns
22, 23
Data hold skew factor
t
QHS
0.55
0.75
ns
ACTIVE to PRECHARGE command
t
RAS
42
70,000
40
120,000
ns
31
ACTIVE to READ with Auto precharge
command
64MB
t
RAP
18
15
ns
42
128MB
18
15
ns
ACTIVE to ACTIVE/AUTO REFRESH command period
t
RC
60
60
ns
AUTO REFRESH command period
t
RFC
72
75
ns
46
ACTIVE to READ or WRITE delay
t
RCD
18
15
ns
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
16
2003 Micron Technology. Inc.
PRECHARGE command period
t
RP
18
15
ns
DQS read preamble
t
RPRE
0.9
1.1
0.9
1.1
t
CK
38
DQS read postamble
t
RPST
0.4
0.6
0.4
0.6
t
CK
ACTIVE bank a to ACTIVE bank b command
t
RRD
12
15
ns
DQS write preamble
t
WPRE
0.25
0.25
t
CK
DQS write preamble setup time
t
WPRES
0
0
ns
18, 19
DQS write postamble
t
WPST
0.4
0.6
0.4
0.6
t
CK
17
Write recovery time
t
WR
15
15
ns
Internal WRITE to READ command delay
t
WTR
1
1
t
CK
Data valid output window
na
t
QH -
t
DQSQ
t
QH -
t
DQSQ
ns
22
REFRESH to REFRESH command interval
64MB
t
REFC
140.6
140.6
s
21
128MB
70.3
70.3
s
21
Average periodic refresh interval
64MB
t
REFI
15.6
15.6
s
21
128MB
7.8
7.8
s
21
Terminating voltage delay to V
DD
t
VTD
0
0
ns
Exit SELF REFRESH to non-READ command
t
XSNR
75
75
ns
Exit SELF REFRESH to READ command
t
XSRD
200
200
t
CK
Table 15: DDR SDRAM Component Electrical Characteristics and Recommended AC
Operating Conditions (-335, -262) (Continued)
Notes: 15, 12-15, 29, 50; notes appear on pages 1922; 0C
T
A
+70C; V
DD
= V
DD
Q = +2.5V 0.2V
AC CHARACTERISTICS
-335
-262
UNITS
NOTES
PARAMETER
SYMBOL
MIN
MAX
MIN
MAX
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
17
2003 Micron Technology. Inc.
Table 16: DDR SDRAM Component Electrical Characteristics and Recommended AC
Operating Conditions (-26A, -265, -202)
Notes: 15, 12-15, 29, 50; notes appear on pages 1922; 0C
T
A
+70C; V
DD
= V
DD
Q = +2.5V 0.2V
AC CHARACTERISTICS
-26A/-265
-202
UNITS
NOTES
PARAMETER
SYMBOL
MIN
MAX
MIN
MAX
Access window of DQs from CK/CK#
t
AC
-0.75
+0.75
-0.8
+0.8
ns
CK high-level width
t
CH
0.45
0.55
0.45
0.55
t
CK
26
CK low-level width
t
CL
0.45
0.55
0.45
0.55
t
CK
26
Clock cycle time
CL=2.5
t
CK (2.5)
7.5
13
8
13
ns
41, 48
CL=2
t
CK (2)
7.5/10
13
10
13
ns
41, 48
DQ and DM input hold time relative to DQS
t
DH
0.5
0.6
ns
23, 27
DQ and DM input setup time relative to DQS
t
DS
0.5
0.6
ns
23, 27
DQ and DM input pulse width (for each input)
t
DIPW
1.75
2
ns
27
Access window of DQS from CK/CK#
t
DQSCK
-0.75
+0.75
-0.8
+0.8
ns
DQS input high pulse width
t
DQSH
0.35
0.35
t
CK
DQS input low pulse width
t
DQSL
0.35
0.35
t
CK
DQS-DQ skew, DQS to last DQ valid, per group, per access
t
DQSQ
0.5
0.6
ns
22, 23
Write command to first DQS latching transition
t
DQSS
0.75
1.25
0.75
1.25
t
CK
DQS falling edge to CK rising - setup time
t
DSS
0.2
0.2
t
CK
DQS falling edge from CK rising - hold time
t
DSH
0.2
0.2
t
CK
Half clock period
t
HP
t
CH,
t
CL
t
CH,
t
CL
ns
30
Data-out high-impedance window from CK/CK#
t
HZ
+0.75
+0.8
ns
16, 38
Data-out low-impedance window from CK/CK#
t
LZ
-0.75
-0.8
ns
16, 39
Address and control input hold time (fast slew rate)
t
IH
F
0.90
1.1
ns
12
Address and control input setup time (fast slew rate)
t
IS
F
0.90
1.1
ns
12
Address and control input hold time (slow slew rate)
t
IH
S
1
1.1
ns
12
Address and control input setup time (slow slew rate)
t
IS
S
1
1.1
ns
12
LOAD MODE REGISTER command cycle time
t
MRD
15
16
ns
DQ-DQS hold, DQS to first DQ to go non-valid, per access
t
QH
t
HP -
t
QHS
t
HP -
t
QHS
ns
22, 23
Data hold skew factor
t
QHS
0.75
1
ns
ACTIVE to PRECHARGE command
t
RAS
40
120,000
40
120,000
ns
31
ACTIVE to READ with Auto precharge command
64MB
t
RAP
t
RAS(MIN)-(burst length*
t
CK/2) ns
42
128MB
20
20
ns
ACTIVE to ACTIVE/AUTO REFRESH command period
t
RC
65
70
ns
AUTO REFRESH command period
t
RFC
75
80
ns
46
ACTIVE to READ or WRITE delay
t
RCD
20
20
ns
PRECHARGE command period
t
RP
20
20
ns
DQS read preamble
t
RPRE
0.9
1.1
0.9
1.1
t
CK
38
DQS read postamble
t
RPST
0.4
0.6
0.4
0.6
t
CK
ACTIVE bank a to ACTIVE bank b command
t
RRD
15
15
ns
DQS write preamble
t
WPRE
0.25
0.25
t
CK
DQS write preamble setup time
t
WPRES
0
0
ns
18, 19
DQS write postamble
t
WPST
0.4
0.6
0.4
0.6
t
CK
17
Write recovery time
t
WR
15
15
ns
Internal WRITE to READ command delay
t
WTR
1
1
t
CK
Data valid output window
na
t
QH -
t
DQSQ
t
QH -
t
DQSQ
ns
22
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
18
2003 Micron Technology. Inc.
REFRESH to REFRESH command interval
64MB
t
REFC
140.6
140.6
s
21
128MB 70.3
70.3
s
21
Average periodic refresh interval
64MB
t
REFI
15.6
15.6
s
21
128MB 7.8
7.8
s
21
Terminating voltage delay to V
DD
t
VTD
0
0
ns
Exit SELF REFRESH to non-READ command
t
XSNR
75
80
ns
Exit SELF REFRESH to READ command
t
XSRD
200
200
t
CK
Table 16: DDR SDRAM Component Electrical Characteristics and Recommended AC
Operating Conditions (-26A, -265, -202) (Continued)
Notes: 15, 12-15, 29, 50; notes appear on pages 1922; 0C
T
A
+70C; V
DD
= V
DD
Q = +2.5V 0.2V
AC CHARACTERISTICS
-26A/-265
-202
UNITS
NOTES
PARAMETER
SYMBOL
MIN
MAX
MIN
MAX
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
19
2003 Micron Technology. Inc.
Notes
1. All voltages referenced to V
SS
.
2. Tests for AC timing, I
DD
, and electrical AC and DC
characteristics may be conducted at nominal ref-
erence/supply voltage levels, but the related spec-
ifications and device operation are guaranteed for
the full voltage range specified.
3. Outputs measured with equivalent load:
4. AC timing and I
DD
tests may use a V
IL
-to-V
IH
swing of up to 1.5V in the test environment, but
input timing is still referenced to V
REF
(or to the
crossing point for CK/CK#), and parameter speci-
fications are guaranteed for the specified AC input
levels under normal use conditions. The mini-
mum slew rate for the input signals used to test
the device is 1V/ns in the range between V
IL
(ACV)
and V
IH
(AC).
5. The AC and DC input level specifications are as
defined in the SSTL_2 Standard (i.e., the receiver
will effectively switch as a result of the signal
crossing the AC input level, and will remain in that
state as long as the signal does not ring back
above [below] the DC input LOW [HIGH] level).
6. V
REF
is expected to equal V
DD
Q/2 of the transmit-
ting device and to track variations in the DC level
of the same. Peak-to-peak noise (non-common
mode) on V
REF
may not exceed 2 percent of the
DC value. Thus, from V
DD
Q/2, V
REF
is allowed
25mV for DC error and an additional 25mV for
AC noise. This measurement is to be taken at the
nearest V
REF
by-pass capacitor.
7. V
TT
is not applied directly to the device. V
TT
is a
system supply for signal termination resistors, is
expected to be set equal to V
REF
and must track
variations in the DC level of V
REF
.
8. I
DD
is dependent on output loading and cycle
rates. Specified values are obtained with mini-
mum cycle time at CL = 2 for -262, -26A, and -202,
CL = 2.5 for-335 and -265 with the outputs open.
9. Enables on-chip refresh and address counters.
10. I
DD
specifications are tested after the device is
properly initialized, and is averaged at the defined
cycle rate.
11. This parameter is sampled. V
DD
=
+2.5V 0.2V
,
V
DD
Q =
+2.5V 0.2V
, V
REF
= V
SS
, f = 100 MHz, T
A
=
25C, V
OUT
(DC) = V
DD
Q/2, V
OUT
(peak to peak) =
0.2V. DM input is grouped with I/O pins, reflecting
the fact that they are matched in loading.
12. Command/Address input slew rate = 0.5V/ns. For
-335, -262, -26A, and -265 with slew rates 1V/ns
and faster,
t
IS and
t
IH are reduced to 900ps. If the
slew rate is less than 0.5V/ ns, timing must be der-
ated:
t
IS has an additional 50ps per each 100mV/
ns reduction in slew rate from the 500mV/ns,
while
t
IH remains constant. If the slew rate
exceeds 4.5V/ns, functionality is uncertain.
13. The CK/CK# input reference level (for timing ref-
erenced to CK/CK#) is the point at which CK and
CK# cross; the input reference level for signals
other than CK/CK# is V
REF
.
14. Inputs are not recognized as valid until V
REF
stabi-
lizes. Exception: during the period before V
REF
stabilizes, CKE
0.3 x V
DD
Q is recognized as LOW.
15. The output timing reference level, as measured at
the timing reference point indicated in Note 3, is
V
TT
.
16.
t
HZ and
t
LZ transitions occur in the same access
time windows as valid data transitions. These
parameters are not referenced to a specific voltage
level, but specify when the device output is no
longer driving (HZ) or begins driving (LZ).
17. If DQS transitions to HIGH above V
IH
(DC) MIN,
then it must not transition to LOW below V
IH
(DC)
MIN prior to
t
DQSH (MIN).
18. This is not a device limit. The device will operate
with a negative value, but system performance
could be degraded due to bus turnaround.
19. It is recommended that DQS be valid (HIGH or
LOW) on or before the WRITE command. The
case shown (DQS going from High-Z to logic
LOW) applies when no WRITEs were previously in
progress on the bus. If a previous WRITE was in
progress, DQS could be HIGH during this time,
depending on
t
DQSS.
20. MIN (
t
RC or
t
RFC) for I
DD
measurements is the
smallest multiple of
t
CK that meets the minimum
absolute value for the respective parameter.
t
RAS
(MAX) for I
DD
measurements is the largest multi-
ple of
t
CK that meets the maximum absolute
value for
t
RAS.
Output
(V
OUT
)
Reference
Point
50
V
TT
30pF
QFC#
(V
OUT
)
Reference
Point
75
V
TT
15pF
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
20
2003 Micron Technology. Inc.
Figure 7: Derating Data Valid Window
21. The refresh period is 64ms. This equates to an
average refresh rate of 15.625s (128MB module)
or 7.8125s (256MB module). However, an AUTO
REFRESH command must be asserted at least
once every 140.6s (128MB module) or 70.3s
(256MB module); burst refreshing or posting by
the DRAM controller greater than eight refresh
cycles is not allowed.
22. The valid data window is derived by achieving
other specifications:
t
HP (
t
CK/2),
t
DQSQ, and
t
QH
(
t
QH =
t
HP -
t
QHS). The data valid window derates
directly porportional with the clock duty cycle
and a practical data valid window can be derived.
The clock is allowed a maximum duty cycle varia-
tion of 45/55, beyond which functionality is
uncertain. Figure 7, Derating Data Valid Window,
shows derating curves for duty cycles between 50/
50 and 45/55.
23. Each byte lane has a corresponding DQS.
24. This limit is actually a nominal value and does not
result in a fail value. CKE is HIGH during RE-
FRESH command period (
t
RFC [MIN]) else CKE is
LOW (i.e., during standby).
25. To maintain a valid level, the transitioning edge of
the input must:
a. Sustain a constant slew rate from the current
AC level through to the target AC level, V
IL
(AC)
or V
IH
(AC).
b. Reach at least the target AC level.
c. After the AC target level is reached, continue to
maintain at least the target DC level, V
IL
(DC)
or V
IH
(DC).
26. JEDEC specifies CK and CK# input slew rate must
be
1V/ns (2V/ns differentially).
27. DQ and DM input slew rates must not deviate
from DQS by more than 10 percent. If the DQ/
DM/DQS slew rate is less than 0.5V/ns, timing
must be derated: 50ps must be added to
t
DS and
t
DH for each 100mv/ns reduction in slew rate. If
slew rate exceeds 4V/ns, functionality is uncer-
tain.
28. V
DD
must not vary more than 4 percent if CKE is
not active while any device bank is active.
29. The clock is allowed up to 150ps of jitter. Each
timing parameter is allowed to vary by the same
amount.
30.
t
HP min is the lesser of
t
CL minimum and
t
CH
minimum actually applied to the device CK and
3.750
3.700
3.650
3.600
3.550
3.500
3.450
3.400
3.350
3.300
3.250
3.400
3.350
3.300
3.250
3.200
3.150
3.100
3.050
3.000
2.950
2.900
2.500
2.463
2.425
2.388
2.350
2.313
2.275
2.238
2.200
2.163
2.125
1.8
2.0
2.2
2.4
2.6
2.8
3.0
3.2
3.4
3.6
3.8
50/50
49.5/50.5 49/51
48.5/52.5
48/52
47.5/53.5
47/53
46.5/54.5
46/54
45.5/55.5
45/55
Clock Duty Cycle
ns
-335
-262/-26A/-265 @
t
CK = 10ns
-202 @
t
CK = 10ns
-262/-26A/-265 @
t
CK = 7.5ns
-202 @
t
CK = 8ns
NA
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
21
2003 Micron Technology. Inc.
CK/ inputs, collectively during device bank active.
31. READs and WRITEs with auto precharge are not
allowed to be issued until
t
RAS(MIN) can be satis-
fied prior to the internal precharge command
being issued.
32. Any positive glitch in the nominal voltage must be
less than 1/3 of the clock and not more than
+400mV or 2.9V maximum, whichever is less. Any
negative glitch must be less than 1/3 of the clock
cycle and not exceed either -300mV or 2.2V mini-
mum, whichever is more positive.
33. Normal Output Drive Curves:
a. The full variation in driver pull-down current
from minimum to maximum process, temper-
ature and voltage will lie within the outer
bounding lines of the V-I curve of Figure 8,
Pull-Down Characteristics.
b. The variation in driver pull-down current
within nominal limits of voltage and tempera-
ture is expected, but not guaranteed, to lie
within the inner bounding lines of the V-I
curve of Figure 8, Pull-Down Characteristics.
c. The full variation in driver pull-up current
from minimum to maximum process, temper-
ature and voltage will lie within the outer
bounding lines of the V-I curve of Figure 9,
Pull-Up Characteristics.
d. The variation in driver pull-up current within
nominal limits of voltage and temperature is
expected, but not guaranteed, to lie within the
inner bounding lines of the V-I curve of Figure
9, Pull-Up Characteristics.
e. The full variation in the ratio of the maximum
to minimum pull-up and pull-down current
should be between 0.71 and 1.4, for device
drain-to-source voltages from 0.1V to 1.0V, and
at the same voltage and temperature.
f. The full variation in the ratio of the nominal
pull-up to pull-down current should be unity
10 percent, for device drain-to-source volt-
ages from 0.1V to 1.0V.
34. Reduced Output Drive Curves:
a. The full variation in driver pull-down current
from minimum to maximum process, tempera-
ture and voltage will lie within the outer
bounding lines of the V-I curve of Figure 10,
Reduced Output Pull-Down Characteristics, on
page 22.
b. The variation in driver pull-down current
within nominal limits of voltage and tempera-
ture is expected, but not guaranteed, to lie
within the inner bounding lines of the V-I curve
of Figure 10, Reduced Output Pull-Down Char-
acteristics, on page 22.
c. The full variation in driver pull-up current from
minimum to maximum process, temperature
and voltage will lie within the outer bounding
lines of the V-I curve of Figure 11, Reduced
Output Pull-Up Characteristics, on page 22.
d. The variation in driver pull-up current within
nominal limits of voltage and temperature is
expected, but not guaranteed, to lie within the
inner bounding lines of the V-I curve of
Figure 11, Reduced Output Pull-Up Character-
istics, on page 22.
e. The full variation in the ratio of the maximum
to minimum pull-up and pull-down current
should be between 0.71 and 1.4, for device
drain-to-source voltages from 0.1V to 1.0V, and
at the same voltage.
f. The full variation in the ratio of the nominal
pull-up to pull-down current should be unity
10 percent, for device drain-to-source volt-
ages from 0.1V to 1.0V.
Figure 8: Pull-Down Characteristics
Figure 9: Pull-Up Characteristics
160
140
I
OUT
(mA)
V
OUT
(V)
Nominal low
Minimum
Nominal high
Maximum
120
100
80
60
40
20
0
0.0
0.5
1.0
1.5
2.0
2.5
V
OUT
(V)
0
-20
I
OUT
(mA)
Nominal low
Minimum
Nominal high
Maximum
-40
-60
-80
-100
-120
-140
-160
-180
-200
0.0
0.5
1.0
1.5
2.0
2.5
V
DD
Q - V
OUT
(V)
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
22
2003 Micron Technology. Inc.
35. The voltage levels used are derived from a mini-
mum V
DD
level and the referenced test load. In
practice, the voltage levels obtained from a prop-
erly terminated bus will provide significantly dif-
ferent voltage values.
36. V
IH
overshoot: V
IH
(MAX) = V
DD
Q + 1.5V for a
pulse width
3ns and the pulse width can not be
greater than 1/3 of the cycle rate. V
IL
undershoot:
V
IL
(MIN) = -1.5V for a pulse width
3ns and the
pulse width can not be greater than 1/3 of the
cycle rate.
37. V
DD
and V
DD
Q must track each other.
38. This maximum value is derived from the refer-
enced test load. In practice, the values obtained
in a typical terminated design may reflect up to
310ps less for
t
HZ(MAX) and the last DVW.
t
HZ
(MAX) will prevail over
t
DQSCK (MAX) +
t
RPST
(MAX) condition.
t
LZ (MIN) will prevail over
t
DQSCK (MIN) +
t
RPRE (MAX) condition.
39. For slew rates greater than 1V/ns the (LZ) transi-
tion will start about 310ps earlier.
40. During initialization, V
DD
Q, V
TT
, and V
REF
must
be equal to or less than V
DD
+ 0.3V. Alternatively,
V
TT
may be 1.35V maximum during power up,
even if V
DD
/V
DD
Q are 0V, provided a minimum of
42
W of series resistance is used between the V
TT
supply and the input pin.
41. The current Micron part operates below the slow-
est JEDEC operating frequency of 83 MHz. As
such, future die may not reflect this option.
42.
t
RAP
t
RCD. Does not apply to -335 speed grade.
43. For -335, -262, -26A, and -265, I
DD
3
N
is specified
to be 35mA at 100 MHz.
44. Random addressing changing and 50 percent of
data changing at every transfer.
45. Random addressing changing and 100 percent of
data changing at every transfer.
46. CKE must be active (high) during the entire time a
refresh command is executed. That is, from the
time the AUTO REFRESH command is registered,
CKE must be active at each rising clock edge, until
t
REF later.
47. I
DD
2N specifies the DQ, DQS, and DM to be
driven to a valid high or low logic level. I
DD
2
Q
is
similar to I
DD
2
F
except I
DD
2
Q
specifies the
address and control inputs to remain stable.
Although I
DD
2
F
, I
DD
2
N
, and I
DD
2
Q
are similar,
I
DD
2
F
is "worst case."
48. Whenever the operating frequency is altered, not
including jitter, the DLL is required to be reset.
This is followed by 200 clock cycles (before READ
commands).
49. Leakage number reflects the worst case leakage
possible through the module pin, not what each
memory device contributes.
50. The -335 module speed grade, using the -6R speed
device, has V
DD
(MIN) = 2.4V.
Figure 10: Reduced Output Pull-Down
Characteristics
Figure 11: Reduced Output Pull-Up
Characteristics
0
10
20
30
40
50
60
70
80
0.0
0.5
1.0
1.5
2.0
2.5
V
OUT
(V)
I
OUT
(mA)
Nominal low
Minimum
Nominal high
Maximum
-50
-45
-40
-35
-30
-25
-20
-15
-10
-5
0
0.0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
1.0
V
DD
Q - V
OUT
(V)
I
OUT
(mA)
Nominal low
Minimum
Nominal high
Maximum
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
23
2003 Micron Technology. Inc.
SPD Clock and Data Conventions
Data states on the SDA line can change only during
SCL LOW. SDA state changes during SCL HIGH are
reserved for indicating start and stop conditions (as
shown in Figure 12, Data Validity, and Figure 13, Defi-
nition of Start and Stop).
SPD Start Condition
All commands are preceded by the start condition,
which is a HIGH-to-LOW transition of SDA when SCL
is HIGH. The SPD device continuously monitors the
SDA and SCL lines for the start condition and will not
respond to any command until this condition has been
met.
SPD Stop Condition
All communications are terminated by a stop condi-
tion, which is a LOW-to-HIGH transition of SDA when
SCL is HIGH. The stop condition is also used to place
the SPD device into standby power mode.
SPD Acknowledge
Acknowledge is a software convention used to indi-
cate successful data transfers. The transmitting device,
either master or slave, will release the bus after trans-
mitting eight bits. During the ninth clock cycle, the
receiver will pull the SDA line LOW to acknowledge
that it received the eight bits of data (as shown in Fig-
ure 14, Acknowledge Response from Receiver).
The SPD device will always respond with an
acknowledge after recognition of a start condition and
its slave address. If both the device and a WRITE oper-
ation have been selected, the SPD device will respond
with an acknowledge after the receipt of each subse-
quent eight-bit word. In the read mode the SPD device
will transmit eight bits of data, release the SDA line and
monitor the line for an acknowledge. If an acknowl-
edge is detected and no stop condition is generated by
the master, the slave will continue to transmit data. If
an acknowledge is not detected, the slave will termi-
nate further data transmissions and await the stop
condition to return to standby power mode.
Figure 12: Data Validity
Figure 13: Definition of Start and Stop
Figure 14: Acknowledge Response from Receiver
SCL
SDA
DATA STABLE
DATA STABLE
DATA
CHANGE
SCL
SDA
START
BIT
STOP
BIT
SCL from Master
Data Output
from Transmitter
Data Output
from Receiver
9
8
Acknowledge
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
24
2003 Micron Technology. Inc.
Figure 15: SPD EEPROM Timing Diagram
Table 17: EEPROM Device Select Code
Most significant bit (b7) is sent first
SELECT CODE
DEVICE TYPE IDENTIFIER
CHIP ENABLE
RW
b7
b6
b5
b4
b3
b2
b1
b0
Memory Area Select Code (two arrays)
1
0
1
0
SA2
SA1
SA0
RW
Protection Register Select Code
0
1
1
0
SA2
SA1
SA0
RW
Table 18: EEPROM Operating Modes
MODE
RW BIT
WC
BYTES
INITIAL SEQUENCE
Current Address Read
1
V
IH
or V
IL
1
START, Device Select, RW = `1'
Random Address Read
0
V
IH
or V
IL
1
START, Device Select, RW = `0', Address
1
V
IH
or V
IL
1
reSTART, Device Select, RW = `1'
Sequential Read
1
V
IH
or V
IL
1
Similar to Current or Random Address Read
Byte Write
0
V
IL
1
START, Device Select, RW = `0'
Page Write
0
V
IL
16
START, Device Select, RW = `0'
SCL
SDA IN
SDA OUT
tLOW
tSU:STA
tHD:STA
tF
tHIGH
tR
tBUF
tDH
tAA
tSU:STO
tSU:DAT
tHD:DAT
UNDEFINED
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
25
2003 Micron Technology. Inc.
NOTE:
1. The SPD EEPROM WRITE cycle time (
t
WRC) is the time from a valid stop condition of a write sequence to the end of the
EEPROM internal erase/program cycle. During the WRITE cycle, the EEPROM bus interface circuit is disabled, SDA
remains HIGH due to pull-up resistor, and the EEPROM does not respond to its slave address.
Table 19: Serial Presence-Detect EEPROM DC Operating Conditions
All voltages referenced to V
SS
; V
DDSPD
= +2.3V to +3.6V
PARAMETER/CONDITION
SYMBOL
MIN
MAX
UNITS
SUPPLY VOLTAGE
V
DDSPD
2.3
3.6
V
INPUT HIGH VOLTAGE: Logic 1; All inputs
V
IH
V
DDSPD
0.7 V
DDSPD
+ 0.5
V
INPUT LOW VOLTAGE: Logic 0; All inputs
V
IL
-1
V
DDSPD
0.3
V
OUTPUT LOW VOLTAGE: I
OUT
= 3mA
V
OL
0.4
V
INPUT LEAKAGE CURRENT: V
IN
= GND to V
DD
I
LI
10
A
OUTPUT LEAKAGE CURRENT: V
OUT
= GND to V
DD
I
LO
10
A
STANDBY CURRENT: SCL = SDA = V
DD
- 0.3V; All other inputs = V
SS
or V
DD
I
SB
30
A
POWER SUPPLY CURRENT: SCL clock frequency = 100 KHz
I
CC
2
mA
Table 20: Serial Presence-Detect EEPROM AC Operating Conditions
All voltages referenced to V
SS
; V
DDSPD
= +2.3V to +3.6V
PARAMETER/CONDITION
SYMBOL
MIN
MAX
UNITS
NOTES
SCL LOW to SDA data-out valid
t
AA
0.3
3.5
s
Time the bus must be free before a new transition can start
t
BUF
4.7
s
Data-out hold time
t
DH
300
ns
SDA and SCL fall time
t
F
300
ns
Data-in hold time
t
HD:DAT
0
s
Start condition hold time
t
HD:STA
4
s
Clock HIGH period
t
HIGH
4
s
Noise suppression time constant at SCL, SDA inputs
t
I
100
ns
Clock LOW period
t
LOW
4.7
s
SDA and SCL rise time
t
R
1
s
SCL clock frequency
t
SCL
100
KHz
Data-in setup time
t
SU:DAT
250
ns
Start condition setup time
t
SU:STA
4.7
s
Stop condition setup time
t
SU:STO
4.7
s
WRITE cycle time
t
WRC
10
ms
1
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
26
2003 Micron Technology. Inc.
Table 21: Serial Presence-Detect Matrix
"1"/"0": Serial Data, "driven to HIGH"/"driven to LOW"; notes appear following matrix
BYTE
DESCRIPTION
ENTRY (VERSION)
MT5VDDT872H
MT5VDDT1672H
0
Number of SPD Bytes Used by Micron
128
80
80
1
Total Number of Bytes in SPD Device
256
08
08
2
Fundamental Memory Type
DDR SDRAM
07
07
3
Number of Row Addresses on Assembly
12,13
0C
0D
4
Number of Column Addresses on Assembly
10
09
09
5
Number of Physical Ranks on DIMM
1
01
01
6
Module Data Width
72
48
48
7
Module Data Width (Continued)
0
00
00
8
Module Voltage Interface Levels (V
DD
Q)
SSTL 2.5V
04
04
9
SDRAM Cycle Time, (
t
CK) CAS Latency = 2.5
(See note 1)
6ns (-335)
7ns (-262/-26A)
7.5ns (-265)
8ns (-202)
60
70
75
80
60
70
75
80
10
SDRAM Access From Clock (
t
AC) CAS Latency = 2.5
0.7ns (-335)
0.75ns (-262/-26A/-265)
0.8ns (-202)
70
75
80
70
75
80
11
Module Configuration Type
ECC
02
02
12
Refresh Rate/Type
15.62s, 7.8s/SELF
80
82
13
SDRAM Device Width (Primary DDR SDRAM)
16
10
10
14
Error-checking DDR SDRAM Data Width
16
10
10
15
Minimum Clock Delay, Back-to-Back Random
Column Access
1 clock
01
01
16
Burst Lengths Supported
2, 4, 8
0E
0E
17
Number of Banks on DDR SDRAM Device
4
04
04
18
CAS Latencies Supported
2, 2.5
0C
0C
19
CS Latency
0
01
01
20
WE Latency
1
02
02
21
SDRAM Module Attributes
Unbuffered/Diff. Clock
20
20
22
SDRAM Device Attributes: General
Fast/Concurrent AP
C1
C1
23
SDRAM Cycle Time, (
t
CK) CAS Latency = 2
7.5ns (-335/-262/-26A)
10ns (-265/-202)
75
A0
75
A0
24
SDRAM Access From Clock (
t
AC) CAS Latency = 2
0.7ns (-335)
0.75ns (-262/-26A/-265)
0.8ns (-202)
70
75
80
70
75
80
25
SDRAM Cycle Time, (
t
CK) CAS Latency = 1.5
N/A
00
01
26
SDRAM Access from CK , (
t
AC) CAS Latency = 1.5
N/A
00
01
27
Minimum Row Precharge Time, (
t
RP)
18ns (-335)
15ns (-262)
20ns (-26A/-265/-202)
48
3C
50
48
3C
50
28
Minimum Row Active to Row Active, (
t
RRD)
12ns (-335)
15ns (-262/-26A/-265/-202)
30
3C
30
3C
29
Minimum RAS# to CAS# Delay, (
t
RCD)
18ns (-335)
15ns (-262)
20ns (-26A/-265/-202)
48
3C
50
48
3C
50
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
27
2003 Micron Technology. Inc.
30
Minimum RAS# Pulse Width, (
t
RAS), (See note 3)
42ns (-335)
45ns (-262/-26A/-265)
40ns (-202)
2A
2D
28
2A
2D
28
31
Module Rank Density
64MB, 128MB
10
20
32
Address and Command Setup Time, (
t
IS),
(See note 4)
0.8ns (-335)
1.0ns (-262/-26A/-265)
1.1ns (-202)
80
A0
B0
80
A0
B0
33
Address and Command Hold Time, (
t
IH),
(See note 4)
0.8ns (-335)
1.0ns (-262/-26A/-265)
1.1ns (-202)
80
A0
B0
80
A0
B0
34
Data/Data Mask Input Setup Time, (
t
DS)
0.45ns (-335)
0.5ns (-262/-26A/-265)
0.6ns (-202)
45
50
60
45
50
60
35
Data/Data Mask Input Hold Time, (
t
DH)
0.45ns (-335)
0.5ns (-262/-26A/-265)
0.6ns (-202)
45
50
60
45
50
60
36-40 Reserved
00
00
41
Minimum Active Auto Refresh Time (
t
RC)
60ns (335/-262)
65ns (-26A/-265)
70ns (-202)
3C
41
46
3C
41
46
42
Minimum Auto Refresh to Active/Auto Refresh
Command Period, (
t
RFC)
72ns (-335)
75ns (-262/-26A/-265)
80ns (-202)
48
4B
50
48
4B
50
43
SDRAM Device Max Cycle Time (
t
CK
MAX
)
12ns (-335)
13ns (-262/-26A/-265/-202)
30
34
30
34
44
SDRAM Device Max DQS-DQ Skew Time (
t
DQSQ)
0.45ns (-335)
0.5ns (-262/-26A/-265)
0.6ns (-202)
2D
32
3C
2D
32
3C
45
SDRAM Device Max Read Data Hold Skew Factor
(
t
QHS)
0.55ns (-335)
0.75ns (-262/-26A/-265)
1.0ns (-202)
55
75
A0
55
75
A0
46
Reserved
00
00
47
DIMM Height
01
01
4861 Reserved
00
00
62
SPD Revision
Release 1.0
10
10
63
Checksum for Bytes 0-62
-335
-262
-26A
-265
-202
16
E9
16
46
E1
29
BC
E9
19
B4
64
Manufacturer's JEDEC ID Code
MICRON
2C
2C
65-71 Manufacturer's JEDEC IDCode
(Continued)
00
00
72
Manufacturing Location
0112
01 - 0C
01 - 0C
73-90 Module Part Number (ASCII)
Variable Data
Variable Data
91
PCB Identification Code
1-9
01 - 09
01 - 09
92
Identification Code (Continued)
0
00
00
Table 21: Serial Presence-Detect Matrix (Continued)
"1"/"0": Serial Data, "driven to HIGH"/"driven to LOW"; notes appear following matrix
BYTE
DESCRIPTION
ENTRY (VERSION)
MT5VDDT872H
MT5VDDT1672H
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice.
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
28
2003 Micron Technology. Inc.
NOTE:
1. Value for -26A
t
CK set to 7ns (0x70) for optimum BIOS compatibility. Actual device spec. value is 7.5ns.
2. The value of
t
RAS used for -262/-26A/-265 modules is calculated from
t
RC -
t
RP. Actual device spec. value is 40 ns.
3. The JEDEC SPD specification allows fast or slow slew rate values for these bytes. The worst-case (slow slew rate) value is
represented here. Systems requiring the fast slew rate setup and hold values are supported, provided the faster mini-
mum slew rate is met.
93
Year of Manufacture in BCD
Variable Data
Variable Data
94
Week of Manufacturein BCD
Variable Data
Variable Data
95-98 Module Serial Number
Variable Data
Variable Data
99-127 Manufacturer-specific Data (RSVD)
Table 21: Serial Presence-Detect Matrix (Continued)
"1"/"0": Serial Data, "driven to HIGH"/"driven to LOW"; notes appear following matrix
BYTE
DESCRIPTION
ENTRY (VERSION)
MT5VDDT872H
MT5VDDT1672H
8000 S. Federal Way, P.O. Box 6, Boise, ID 83707-0006, Tel: 208-368-3900
E-mail: prodmktg@micron.com, Internet: http://www.micron.com, Customer Comment Line: 800-932-4992
Micron, the M logo, and the Micron logo are trademarks and/or service marks of Micron Technology, Inc.
64MB, 128MB (x72, ECC)
200-PIN DDR SDRAM SODIMM
09005aef80a8e767
Micron Technology, Inc., reserves the right to change products or specifications without notice..
DD5C8_16x72HG_C.fm - Rev. C 7/03 EN
29
2003 Micron Technology, Inc
Figure 16: 200-Pin SODIMM Dimensions
NOTE:
All dimensions are in inches (millimeters)
or typical where noted.
Data Sheet Designation
Released (No Mark): This data sheet contains mini-
mum and maximum limits specified over the complete
power supply and temrperature range for production
devices. Although considered final, these specifica-
tions are subject to change, as further product devel-
opment and data characterization sometimes occur.
U1
U2
U3
U4
U5
U6
0.150 (3.80)
MAX
0.043 (1.10)
0.035 (0.90)
PIN 1
2.666 (67.72)
2.656 (67.45)
0.787 (20.00)
TYP
0.071 (1.80)
(2X)
0.024 (0.60)
TYP
0.018 (0.45)
TYP
0.079 (2.00) R
(2X)
PIN 199
FRONT VIEW
0.085 (2.15)
0.236 (6.00)
2.504 (63.60)
TYP
0.091 (2.30)
0.039 (1.0)
TYP
1.244 (31.60)
1.256 (31.90)
0.449 (11.40)
TYP
1.87 (47.40)
TYP
BACK VIEW
PIN 2
PIN 200
MAX
MIN