3236 Scott Boulevard
Santa Clara, California 95054
Phone: (408) 986-5060
Fax: (408) 986-5095
CMM6004-SC
Features
0.25 to 3.0 GHz Frequency Range
41 dBm Output IP3
2.1 dB Noise Figure
14.5 dB Gain
23.5 dBm P1dB
SOT-89 SMT Package
Single Power Supply
+3V to +5V Voltage Rail
Description
The CMM6004-SC is a high dynamic range amplifier
designed for applications operating within the 0.25 to 3.0 GHz
frequency range. It is an ideal solution for transmit and receive
functions where high linearity is required.
The amplifier has the flexibility of being optimized
for a number of wireless applications. The combination of low
NF and high IP3 at the same bias point make it an ideal trans-
mit or receive solution when used in applications including
cellular and PCS (personal communications service) operating
from 0.8 to 2.2 GHz; MMDS (multichannel multipoint distrib-
ution systems) operating from 2.2 to 2.7 GHz; and WLAN
(wireless LAN) operating at 2.4 GHz.
The CMM6004-SC is packaged in a low-cost, space
efficient, surface mount SOT-89 package which provides
excellent electrical stability and low thermal resistance. All
devices are 100% RF and DC tested.
0.25 to 3.0 GHz
High Dynamic Range
Amplifier
Advanced Product Information
February 2003
(1 of 4)
Functional Block Diagram
Absolute Maximum Ratings
Parameter
Rating
Parameter
Rating
Parameter
Rating
Supply Voltage
+6.0 V
Storage Temperature
-55C to +125C
Operating Temperature
-40C to +85C
RF Input Power
+10 dBm
Junction Temperature
150C
Thermal Resistance
89C/W
Parameter
Condition
Min
Typ
Max
Units
Frequency Range
0.25
3.0
GHz
Gain
Externally matched
13.5
14.5
dB
Input Return Loss
Externally matched
-10
dB
Output IP3
+38
+41
dBm
Noise Figure
1.6
2.1
dB
Output P1dB
23
dBm
Operating Current Range
120
150
180
mA
Supply Voltage
5.0
V
Electrical Characteristics
Unless otherwise specified, the following specifications are guaranteed at room temperature
in a Celeritek test fixture.
Notes:
1. T = 25C, Vdd = 5.0, Frequency = 800 MHz, 50 Ohm system
2. OIP3 measured with two tones at output power of 5 dBm/tone separated by 10 MHz.
Operation of this device above any of these parameters may cause damage.
Parameter
Typical
Units
Frequency Range
900
1900
2400
MHz
Gain
16.5
14.5
13.6
dB
Input Return Loss
-18
-15
-15
dB
Output Return Loss
-14
-10
-12
dB
Output IP3
+41.5 +41.0
+41.0
dBm
Output P1dB
23.8
23.5
23.0
dBm
Noise Figure
1.8
2.2
2.3
dB
Typical Parameters
Notes:
1. Typical values reflect performance in recommended application circuit.
Input
Ground Output
Bias
Ground
1
2
3
4
3236 Scott Boulevard, Santa Clara, California 95054
Phone: (408) 986-5060
Fax: (408) 986-5095
CMM6004-SC
Advanced Product Information - February 2003
(2 of 4)
Typical Performance
3236 Scott Boulevard
Santa Clara, California 95054
Phone: (408) 986-5060
Fax: (408) 986-5095
CMM6004-SC
Advanced Product Information - August 2002
(3 of 4)
Application Circuit (900 MHz)
Typical Performance (50 Ohm System)
Frequency
900 MHz
Gain
16.5 dB
Input Return Loss
-18.0 dB
Output Return Loss
-14.0 dB
OIP3
41.0 dBm
Noise Figure
1.8 dB
Bias
Vds = 5V, Id = 173 mA
P1dB
23.8 dBm
uuuu
L
12 nH
RF
IN
CMM6004-SC
T = 100 mil
Z = 38
INPUT MATCHING
NETWORK
Application Circuit (1900 MHz)
Typical Performance (50 Ohm System)
Frequency
1900 MHz
Gain
14.5 dB
Input Return Loss
-15 dB
Output Return Loss
-10 dB
OIP3
41.0 dBm
Noise Figure
2.2 dB
Bias
Vds = 5V, Id = 174 mA
P1dB
23.5 dBm
RF
OUT
uuuu
uuuu
C
56 pF
L
47 nH
Vcc
5V
C
56 pF
L
6.8 nH
RF
IN
CMM6004-SC
T = 100 mil
Z = 38
INPUT MATCHING
NETWORK
C
2.2 pF
T = 200 mil
Z = 38
uuuu
L
2.7 nH
RF
OUT
uuuu
C
56 pF
L
47 nH
Vcc
5V
C
56 pF
T = 200 mil
Z = 38
Application Circuit (2400 MHz)
Typical Performance (50 Ohm System)
Frequency
2400 MHz
Gain
13.6 dB
Input Return Loss
-15 dB
Output Return Loss
-12 dB
OIP3
41.0 dBm
Noise Figure
2.3 dB
Bias
Vds = 5V, Id = 175 mA
P1dB
23.0 dBm
RF
OUT
uuuu
uuuu
C
56 pF
L
47 nH
Vcc
5V
C
56 pF
L
6.8 nH
RF
IN
CMM6004-SC
T = 100 mil
Z = 38
INPUT MATCHING
NETWORK
C
1.2 pF
T = 200 mil
Z = 38
uuuu
L
2.2 nH
3236 Scott Boulevard, Santa Clara, California 95054
Phone: (408) 986-5060
Fax: (408) 986-5095
CMM6004-SC
Advanced Product Information - February 2003
(4 of 4)
Celeritek reserves the right to make changes without further notice to any products herein. Celeritek makes no warranty, representation or guarantee regarding the
suitability of its products for any particular purpose, nor does Celeritek assume any liability arising out of the application or use of any product or circuit, and specifically
disclaims any and all liability, including without limitation consequential or incidental damages. "Typical" parameters can and do vary in different applications. All operating
parameters, including "Typicals" must be validated for each customer application by customer's technical experts. Celeritek does not convey any license under its patent
rights nor the rights of others. Celeritek products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body,
or other applications intended to support or sustain life, or for any other application in which the failure of the Celeritek product could create a situation where personal
injury or death may occur. Should Buyer purchase or use Celeritek products for any such unintended or unauthorized application, Buyer shall indemnify and hold Celeritek
and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out
of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such claim alleges that Celeritek was negligent
regarding the design or manufacture of the part. Celeritek is a registered trademark of Celeritek, Inc. Celeritek, Inc. is an Equal Opportunity/Affirmative Action Employer.
Ordering Information
The CMM6004-SC is available in a surface-mount SOT-89 package and devices are available in tape and reel.
Part Number for Ordering
Package
CMM6004-SC
SOT-89 surface-mount power package in tape and reel
PB-CMM6004-SC
Evaluation Board with SMA connectors for CMM6004-SC
1
2
3
4
6XXX
XXXXXX
ZYYWW
DIMENSIONS IN INCHES
[MILLIMETERS]
4.50
[0.177]
1.73
[0.068]
0.46
[0.18]
3X
1.50
[0.059]
3.00
[0.118]
0.76
[0.030]
0.38
[0.015]
0.38
[0.015]
4.41
[0.163]
1.55
[0.061]
2.50
[0.096]
0.71
[0.028]
MARKINGS:
6XXX = CELERITEK MODEL NO.
XXXXXX = WAFER LOT NO.
ZYYWW = DATE CODE (YR/WEEK)
FIRST LETTER COUNTRY OF ORIGIN IF OTHER THAT USA
0.99
[0.039]
0.58
[0.023]
0.64
[0.025]
0.86
[0.034]
1.27
[0.050]
3.48
[0.137]
5.33
[0.210]
3.86
[0.152]
1.70
[0.067]
2.06
[0.081]
0.41
[0.016]
Physical Dimensions
PDF 
ZIP