Features
q
High Speed Operation 15GHz
q
Silicon Technology for Low Phase Noise (Typically
Better Than 2140dBc / Hz at 10kHz)
q
Very Low Power Dissipation: 150mW (Typ.)
q
Single 5V Supply Operation
q
High Input Sensitivity
q
Very Wide Operating Frequency Range
q
Available as DESC SMD 5962 - 9157201MPA
Absolute Maximum Ratings
Supply voltage, V
CC
- 6.5V
Clock input voltage
2.5V p-p
Storage temperature range
65
C to +150
C
Junction temperature
+ 175
C
Ordering Information
SP8830 A DG
SP8830 B DG
DES9157201/AC/DGAZ (SMD)
V
CC
1mA
OUTPUT
OUTPUT
GND
7
6
1
5
125k
125k
INPUT
INPUT
2
3
08mA
1k
2k
08mA
4
2
4
5
SP8830
1.5GHz
10 Prescaler
Advance Information
DS3690
Issue 3.3
June 1999
Figure 1 SP8830 block diagram
q
Temperature Range: 255
C to 1125
C (A Grade)
2
40
C to 185
C (B Grade)
Description
The SP8830 is one of a range of very high speed low
power prescalers for professional and military
applications. The device features a complementary output
stage with on chip current sources for the emitter follower
outputs.
2
SP8830
Advance Information
Electrical Characteristics
Unless otherwise stated, the Electrical Characteristics are guaranteed over specified supply, frequency and
temperature range
Supply voltage, V
CC
-475V to +525V
Temperature, T
AMB
= -55
C to +125
C (A Grade), -40
C to +85
C (B Grade)
Characteristic
Supply current, I
CC
Input sensitivity, 100MHz to
1500MHz
Input impedance (series equivalent)
Output voltage with f
IN
= 100MHz
Output voltage with f
IN
= 1500MHz
07
Value
Typ.
Max.
Min.
Units
Pin
40
50
2
1
04
50
100
mA
mV
pF
V p-p
V p-p
RMS sinewave, measured in 50
system. See Figs 3 and 4.
See Fig. 5
Conditions
1
2, 3
2, 3
6, 7
6, 7
400
150
100
50
100 500 1000 1500 2000
FREQUENCY (MHz)
V
IN
(mV RMS INTO 50
)
*
Tested as specified
in table of Electrical
Characteristics
GUARANTEED
*
OPERATING
WINDOW
Figure 3 Typical input sensitivity
Figure 2 Pin connections
V
CC
INPUT
INPUT
NC
NC
OUTPUT
OUTPUT
GND
1
2
3
4
8
7
6
5
DG8
3
Advance Information
SP8830
1
2
3
4
8
7
6
5
1n
01
1
5V
1n
RATIO
COUNTER
POWER
METER
50
50
SIGNAL GENERATOR
Output load for
amplitude measurements
3p
01
FROM
OUTPUT
COAXIAL
SWITCH
SP8830
1k
j 2
j 1
j 0.5
j 0.2
0
2
j 0.2
2
j 0.5
2
j 1
2
j 2
1
0.5
0.2
j 5
2
j 5
2
5
500MHz
1500MHz
100MHz
1000MHz
Figure 4 Test circuit
Figure 5 Typical input impdance, normalised to 50
M Mitel (design) and ST-BUS are registered trademarks of MITEL Corporation
Mitel Semiconductor is an ISO 9001 Registered Company
Copyright 1999 MITEL Corporation
All Rights Reserved
Printed in CANADA
TECHNICAL DOCUMENTATION - NOT FOR RESALE
World Headquarters - Canada
Tel: +1 (613) 592 2122
Fax: +1 (613) 592 6909
North America
Asia/Pacific
Europe, Middle East,
Tel: +1 (770) 486 0194
Tel: +65 333 6193
and Africa (EMEA)
Fax: +1 (770) 631 8213
Fax: +65 333 6192
Tel: +44 (0) 1793 518528
Fax: +44 (0) 1793 518581
http://www.mitelsemi.com
Information relating to products and services furnished herein by Mitel Corporation or its subsidiaries (collectively "Mitel") is believed to be reliable. However, Mitel assumes no
liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of
patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or
service conveys any license, either express or implied, under patents or other intellectual property rights owned by Mitel or licensed from third parties by Mitel, whatsoever.
Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Mitel, or non-Mitel furnished goods or services may infringe patents or
other intellectual property rights owned by Mitel.
This publication is issued to provide information only and (unless agreed by Mitel in writing) may not be used, applied or reproduced for any purpose nor form part of any order or
contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this
publication are subject to change by Mitel without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or
service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific
piece of equipment. It is the user's responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or
data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in
any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Mitel's
conditions of sale which are available on request.
PDF 
ZIP