4707 Dey Road Liverpool, N.Y. 13088
(315) 701-6751
FEATURES:
All N-Channel Mosfets
Isolated Package for Direct Heat Sinking, Excellent Thermal Conductivity
Avalanche Rated Devices
Interfaces with Most Brushless Motor Drive IC's
200 Volt, 20 Amp Full Three Phase Bridge at 25C
ISO-9001 CERTIFIED BY DSCC
M.S.KENNEDY CORP.
THREE PHASE BRIDGE
MOSFET POWER MODULE
The MSK 3016 is an all N-Channel three phase power MOSFET Bridge Circuit. Packaged in a space efficient isolated
ceramic tab power SIP that allows for direct heat sinking, the MSK 3016 can be interfaced with a wide array of brushless
motor drive IC's. The MSK 3016 uses M.S Kennedy's proven power hybrid technology to produce a cost effective high
performance circuit for use in today's sophisticated servo motor and disk drive systems.
DESCRIPTION:
EQUIVALENT SCHEMATIC
Three Phase Brushless DC Motor Servo Control
Disk Drive Spindle Control
Fin Actuator Control
Az-El Antenna Control
TYPICAL APPLICATIONS
PIN-OUT INFORMATION
1
2
3
4
5
6
7
8
9
10
11
Drain Q2, Q4, Q6
Drain Q2, Q4, Q6
Drain Q2, Q4, Q6
Gate Q2
Gate Q1
Drain Q1, Source Q2
Drain Q1, Source Q2
Drain Q1, Source Q2
Gate Q4
Gate Q3
Drain Q3, Source Q4
Drain Q3,Source Q4
Drain Q3, Source Q4
Source Q1, Q3, Q5
Source Q1, Q3, Q5
Source Q1, Q3, Q5
Gate Q6
Drain Q5, Source Q6
Drain Q5, Source Q6
Drain Q5, Source Q6
Gate Q5
12
13
14
15
16
17
18
19
20
21
3016
1
Rev. - 5/01
Drain-Source Leakage Current
Gate-Source Threshold Voltage
Drain-Source On Resistance
Drain-Source On Resistance
Forward Transconductance
Forward On Voltage
Reverse Recovery Time
Reverse Recovery Charge
Drain-Source Breakdown Voltage
Gate-Source Leakage Current
Total Gate Charge
Gate-Source Charge
Gate-Drain Charge
Turn-On Delay Time
Rise Time
Turn-Off Delay Time
Fall Time
Input Capacitance
Output Capacitance
Reverse Transfer Capacitance
Body Diode
1
2
3
4
410 mJ
+150C MAX
-55C to +150C
-55C to +125C
300C MAX
Single Pulse Avalanche Energy
Junction Temperature
Storage Temperature
Case Operating Temperature Range
Lead Temperature Range
(10 Seconds)
Drain to Source Voltage
Drain to Gate Voltage
(R
GS
=1M
)
Gate to Source Voltage
(Continuous)
Continuous Current
Pulsed Current
Thermal Resistance
(Junction to Case)@25C
Thermal Resistance
(Junction to Case)@125C
ABSOLUTE MAXIMUM RATINGS
V
DSS
V
DGDR
V
GS
I
D
I
DM
R
TH-JC
R
TH-JC
T
J
T
ST
T
C
T
LD
200V MAX
200V MAX
20V MAX
20A MAX
30A MAX
1.3C/W
2.1C/W
V
GS
=0 I
D
=0.25mA
V
DS
=200V V
GS
=0V
V
GS
=20V V
DS
=0
V
DS
=V
GS
I
D
=250A
V
GS
=10V ID = 20A
V
GS
=10V I
D
=20A
V
DS
=50V I
D
=20A
I
D
= 20A
V
DS
=160V
V
GS
= 10V
V
DD
=100V
I
D
= 20A
R
G
= 6.2
R
D
= 3.2
V
GS
=0V
V
DS
=25V
f=1MHz
I
S
=20 A V
GS
=0V
I
S
=20 A di/dt=100A/S
Parameter
Units
MSK3001
Test Conditions
V
A
nA
V
S
nC
nC
nC
nS
nS
nS
nS
pF
pF
pF
V
nS
C
M i n .
200
-
-
2.0
-
-
2.7
-
-
-
-
-
-
-
-
-
-
-
-
-
T y p .
-
-
-
-
-
-
-
-
-
-
16
86
70
62
2800
780
250
2.0
360
4.6
M a x .
-
250
100
4.0
0.12
0.09
-
140
28
74
-
-
-
-
-
-
-
-
540
6.9
ELECTRICAL SPECIFICATIONS
2
NOTES:
This parameter is guaranteed by design but need not be tested. Typical parameters are representative of actual device performance but are for reference only.
Resistance as seen at package pins.
Resistance for die only; use for thermal calculations.
T
A
=25C unless otherwise specified.
4
2
Rev. - 5/01
1
1
1
1
1
1
3
1
1
1
1
1
1
1
1
This deadtime should allow for the turn on and turn off time of the transistors, especially when slowing them down with gate
resistors. This situation will be present when switching motor direction, or when sophisticated timing schemes are used for servo
systems such as locked antiphase PWM'ing for high bandwidth operation.
APPLICATION NOTES
BRIDGE DRIVE CONSIDERATIONS
It is important that the logic used to turn ON and OFF the various transistors allow sufficient "dead time" between a high side
transistor and its low side transistor to make sure that at no time are they both ON. When they are, this is called "shoot-through",
and it places a momentary short across the power supply. This overly stresses the transistors and causes excessive noise as well.
See Figure 1.
3
Figure 1
Rev. - 5/01
TYPICAL PERFORMANCE CURVES
4
Rev. - 5/01
MECHANICAL SPECIFICATIONS
The information contained herein is believed to be accurate at the time of printing. MSK reserves the right to make
changes to its products or specifications without notice, however, and assumes no liability for the use of its products.
Please visit our website for the most recent revision of this datasheet.
M.S. Kennedy Corp.
4707 Dey Road, Liverpool, New York 13088
Phone (315) 701-6751
FAX (315) 701-6752
www.mskennedy.com
ORDERING INFORMATION
ALL DIMENSIONS ARE 0.010 INCHES UNLESS OTHERWISE LABELED.
5
Rev. - 5/01
Part
Number
Screening Level
MSK 3016
Industrial
PDF 
ZIP