NTE919D
Integrated Circuit
High Speed Dual Comparator
Description:
The NTE919D is a precision high speed dual comparator fabricated on a single monolithic chip. This
devices is designed to operate over a wide range of supply voltages down to a single 5V logic supply
and ground. Further, it has higher gain and lower input currents than devices like the NTE910. The
uncommitted collector of the output stage makes it compatible with RTL, DTL, and TTL as well as
capable of driving lamps and relays at currents up to 25mA.
Although designed primarily for applications requiring operation from digital logic supplies, the
NTE919D is fully specified for power supplies up to
15V.
Features:
D
Two Independent Comparators
D
Operates from a Single 5V Supply
D
Typically 80ns Response Time at
15V
D
Minimum FanOut of 2 Each Side
D
Maximum Input Current of 1
A Over Temperature
D
Inputs and Outputs can be Isolated from System Ground
D
High Common Mode Slew Rate
Absolute Maximum Ratings:
Total Supply Voltage
36V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output to Negative Supply Voltage
36V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ground to Negative Supply Voltage
25V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Ground to Positive Supply Voltage
18V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Differential Input Voltage
5V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Input Voltage (Note 1)
15V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Power Dissipation (Note 2)
500mW
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Output Short Circuit Duration
10sec
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Operating Temperature Range
0
to +70
C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Storage Temperature Range
65
to +150
C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Lead Temperature (Soldering 10 sec)
+260
C
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Note 1. For supply voltages less than
15 the absolute maximum input voltage is equal to the supply
voltage.
Note 2. The maximum junction temperature is 85
C. For operating at elevated temperatures, de-
vices must be derated based on a thermal resistance of 100
C/W, junction to ambient.
Electrical Characteristics: (Note 3)
Parameter
Test Conditions
Min
Typ
Max
Unit
Input Offset Voltage
T
A
= +25
C, R
S
5k, Note 4
2.0
8.0
mV
Input Offset Current
T
A
= +25
C, Note 4
80
200
nA
Input Bias Current
T
A
= +25
C
250
1000
nA
Voltage Gain
T
A
= +25
C, Note 6
8
40
V/mV
Response Time
T
A
= +25
C, V
S
=
15V, Note 5
80
ns
Saturation Voltage
V
IN
10mV, I
OUT
= 25mA T
A
= +25
C
0.75
1.5
V
Output Leakage Current
V
IN
10mV, V
OUT
= 35V, V = V
GND
= 0V,
T
A
= +25
C
0.2
10
A
Input Offset Voltage
R
S
5k, Note 4
10
mV
Input Offset Current
Note 4
300
nA
Input Bias Curent
1200
nA
Input Voltage Range
V
S
=
15V
13
V
V+ = 5V, V = 0
1
3
V
Saturation Voltage
V+
4.5V, V = 0, V
IN
10mV, I
SINK
3.2mA
0.3
0.4
V
Differential Input Voltage
5
V
Positive Supply Current
T
A
= +25
C, V+ = 5V, V = 0
4.3
mA
Positive Supply Current
T
A
= +25
C, V
S
=
15V
8
12.5
mA
Negative Supply Current
T
A
= +25
C, V
S
=
15V
3
5
mA
Note 3. These specifications apply for V
S
=
15V, and 0
C
T
A
70
C, unless otherwise stated.
The offset voltage, offset current and bias current specifications apply for any supply voltage
from a single 5V supply up to
15V supplies. Do not operate the device with more than 16V
from ground to V
S
.
Note 4. The offset voltages and offset currents given are the maximum values required to drive the
output within a volt of either supply with a 1mA load. Thus, these parameters define an error
band and take into account the worst case effects of voltage gain and input impedance.
Note 5. The response time specified is for a 100mV input step with 5mV overdrive.
Note 6. Output is pulled up to 15V through a 1.4
resistor.
Pin Connection Diagram
GND 2
NonInverting Input 2
Inverting Input 2
V (+)
Output 1
N.C.
N.C.
Output 2
V ()
Inverting Input 1
NonInverting Input 1
GND 1
N.C.
N.C.
1
2
3
4
5
6
7
14
13
12
11
10
9
8
PDF 
ZIP