ChipFind - документация

Электронный компонент: OAT1042x-V1-z-yy

Скачать:  PDF   ZIP
OKI Electronic Components
FEDFOAT1042X-V1-01
Issue Data: Feb. 4, 2002
OAT1042x-V1-z-yy
OC192/STM -64 Optical Transceiver Module
1/5
APPLICATION

OC-192 and STM-64 SERDES Transceiver Module
FEATURES
Transmission Distance 12km
Wavelength 1310nm
1:16 DeMUX with LVDS differential 622Mbps data outputs
16:1 MUX with LVDS differential 622Mbps data inputs
TX/RX Loss of Lock
Compact size
Supply voltage; +3.3V , +5V and -5.2V
SPECIFICATION

Optical interface specifications
Parts Number
OAT1042x-V1-z-yy
Parameter
For 12km
Units
Transmitter module
Pout
-4 to 0
dBm
c
1290 to 1330
nm
Optical output waveform
ITU-T G.691 STM-64 Unamplified Mask standard
Extinction ratio
8.2
dB
20
1.0
nm
SMSR
30
dB
Jitter Generation
Compliant with GR-253
Receiver Module
Minimum sensitivity
-12
dBm
Minimum overload
0
dBm
c_rx
1290 ~ 1600
nm
Rx Return loss
27
dB
Jitter Generation, Tolerance
and Transfer
Compliant with GR-253
Optical path
D
LRmax
40
ps/nm
System Optical return loss
24
dB
Optical Path Penalty
1
dB
FEDFOAT1042X-V1-01
OKI Semiconductor
OAT1042x-V1-z-yy
2/5

Power Supply
Parameter
Symbol
Min.
Typ.
Max.
Units
Imax
Supply Voltage
Vdd
3.13
3.3
3.47
V
2A
Vcc
4.75
5
5.25
V
0.8 A
Vee
-4.94
-5.2
-5.45
V
1.8A
Power consumption
8
14
W
Operating Temperature(Case temperature)
0 to 65 degC

Dimensions(without heat sink)
Dimensions
Units
Width
88.9
Length
114.3
Height
13
mm

Connector
Optical
Select SC / FC / LC / MU
Electrical
300pin BERG MegArray@84502-10X

FEDFOAT1042X-V1-01
OKI Semiconductor
OAT1042x-V1-z-yy
3/5
BLOCK DIAGRAM
LsTEMPMON
LsBIASMON
LsPOWMON
LsENABLE
TxDin0-15P/N
TxPICLKP/N
OC192 Optical
Output
TxLOCKERR
TX E-O
Driver
Power Control
LsBIASALM
LsTEMPALM
Temp Control
TxREFCLKP/N
TxLINETIMSEL
RxPOCLKP/N
RxDout0-15P/N
RxREFCLKP/N
RxLOCKERR
OC192 Optical
Input
RxPOWMON
I2CDATA
I2CCLOCK
RX O-E
CDR
with DEMUX
Post AMP
uP
EEPROM
Optional function
Source and
Line Timing modes
TxPCLKP/N
MUX
with CMU
TxRESET
TxREFSEL
Optional function
Manufacturing Infomation stored
TxMCLKP/N
RxLCKREF
ALM
RxPOWALM
RxRESET
RxMCLKP/N
ORDERING INFORMATION
OAT1042x-V1-z-yy
x
z
yy
optical connector
Bitrate(Gbps)
Fiber Length
S
SC
A
9.95
10
1m
F
FC
B
10.3
05
0.5m
L
LC
C
9.95/10.3/10.7
M
MU
D
10.7
FEDFOAT1042X-V1-01
OKI Semiconductor
OAT1042x-V1-z-yy
4/5
PACKAGE OUTLINE
(Unit: mm)
OPT IN






OPT OUT
FEDFOAT1042X-V1-01
OKI Semiconductor
OAT1042x-V1-z-yy
5/5
NOTICE
1. The information contained herein can change without notice owing to product and/or technical improvements.
Before using the product, please make sure that the information being referred to is up -to-date.
2. The outline of action and examples for application circuits described herein have been chosen as an
explanation for the standard action and performance of the product. When planning to use the product, please
ensure that the external conditions are reflected in the actual circuit, assembly, and program designs.
3. When designing your product, please use our product below the specified maximum ratings and within the
specified operating ranges including, but not limited to, operating voltage, power dissipation, and operating
temperature.

4. Oki assumes no responsibility or liability whatsoever for any failure or unusual or unexpected operation
resulting from misuse, neglect, improper installation, repair, alteration or accident, improper handling, or
unusual physical or electrical stress including, but not limited to, exposure to parameters beyond the specified
maximum ratings or operation outside the specified operating range.
5. Neither indemnity against nor license of a third party's industrial and intellectual property right, etc. is
granted by us in connection with the use of the product and/or the information and drawings contained herein.
No responsibility is assumed by us for any infringement of a third party's right which may result from the use
thereof.
6. The products listed in this document are intended for use in general electronics equipment for commercial
applications (e.g., office automation, communication equipment, measurement equipment, consumer
electronics, etc.). These products are not authorized for use in any system or application that requires special
or enhanced quality and reliability characteristics nor in any system or application where the failure of such
system or application may result in the loss or damage of property, or death or injury to humans.
Such applications include, but are not limited to, traffic and automotive equipment, safety devices, aerospace
equipment, nuclear power control, medical equipment, and life-support systems.
7. Certain products in this document may need government approval before they can be exported to particular
countries. The purchaser assumes the responsibility of determining the legality of export of these products
and will take appropriate and necessary steps at their own expense for these.
8. No part of the contents contained herein may be reprinted or reproduced without our prior permission.
9.
Qualification and Reliability
To help ensure high product reliability and customer satisfaction, OKI is committed to an intensive quality
program that starts in the design phase and proceeds through the manufacturing process.
Optical transceiver modules are qualified to OKI internal standards using MIL-STD-883 test methods and
procedures and using sample techniques consistent with Telcordia requirements.
This qualification program fully meets the intent of Telcordia reliability practices GR-468-CORE.
10. Laser Safety
All version of transceiver are Class 1 Laser products FDA complies with 21 CFR 1040.10 and 1040.11
requirements.
Also, all versions are Class 1 Laser products pre IEC 825-1
.
Copyright 2002 Oki Electric Industry Co., Ltd.