ChipFind - документация

Электронный компонент: OAT1043x-V1-z-yy

Скачать:  PDF   ZIP
OKI Electronic Components
FEDFOAT1043X-V1-01
Issue Data: Jan. 15, 2002
OAT1043x-V1-z-yy
OC192/STM -64 Optical Transceiver Module
1/4
APPLICATION

OC-192 and STM-64 SERDES Transceiver
FEATURES
Optical performance compliant with OC-192 IR-2/STM-64 S-64.2b
Electrical interface compliant with OIF1999.102.8 SFI-4
TX/RX Loss of Lock
300pins connector(Pin Assignments compliant with OIF2001.063.1)
Supply voltage; +3.3V , +5V and -5.2V
SPECIFICATION
Parameter
Unit
OAT1043x-V1-A-yy
Parameter
-
IR-2
Operating Bit rate
Gbps
9.95328
Mean launched power range
dBm
-1 to +2
Center wavelength range
nm
1530 to 1565
Minimum extinction ratio
dB
8.2
Maximum spectral width
nm
1.0 (@ 20 dB)
Side mode suppression ratio
dB
30
Received optical power [BER = 10-12]
dBm
-14 to -1
Transmission distance
km
40
Power consumption
W
10 (Typ.)
Operating temperature
C
0 to +65
Dimension
mm
88.9 114.3 13 (without heat sink)

FEDFOAT1043X-V1-01
OKI Semiconductor
OAT1043x-V1-z-yy
2/4
BLOCK DIAGRAM
LsTEMPMON
LsBIASMON
LsPOWMON
LsENABLE
TxDin0-15P/N
TxPICLKP/N
10Gbps Optical Signal
Output
TxLOCKERR
TX E-O
Driver
APC
LsBIASALM
LsTEMPALM
ATC
TxREFCLKP/N
TxPCLKP/N
MUX
with CMU
TxRESET
TxREFSEL
TxMCLKP/N
RxPOCLKP/N
RxDout0-15P/N
RxREFCLKP/N
10Gbps Optical Signal
Input
RxPOWMON
RX O-E
CDR
with DEMUX
Post AMP
RxLCKREF
RxPOWALM
RxRESET
RxMCLKP/N
RxLOCKERR
16
16
FEDFOAT1043X-V1-01
OKI Semiconductor
OAT1043x-V1-z-yy
3/4
PACKAGE OUTLINE
(Unit: mm)
ORDERING INFORMATION
OAT1043x-V1-z-yy
x
z
yy
Optical connector
Bit rate(Gbps)
Fiber length
S
SC
A
9.95
10
1m
F
FC
B
10.3
05
0.5m
L
LC
C
9.95/10.3/10.7
M
MU
D
10.7
FEDFOAT1043X-V1-01
OKI Semiconductor
OAT1043x-V1-z-yy
4/4
NOTICE
1. The information contained herein can change without notice owing to product and/or technical improvements.
Before using the product, please make sure that the information being referred to is up -to-date.
2. The outline of action and examples for application circuits described herein have been chosen as an
explanation for the standard action and performance of the product. When planning to use the product, please
ensure that the external conditions are reflected in the actual circuit, assembly, and program designs.
3. When designing your product, please use our product below the specified maximum ratings and within the
specified operating ranges including, but not limited to, operating voltage, power dissipation, and operating
temperature.

4. Oki assumes no responsibility or liability whatsoever for any failure or unusual or unexpected operation
resulting from misuse, neglect, improper installation, repair, alteration or accident, improper handling, or
unusual physical or electrical stress including, but not limited to, exposure to parameters beyond the specified
maximum ratings or operation outside the specified operating range.
5. Neither indemnity against nor license of a third party's industrial and intellectual property right, etc. is
granted by us in connection with the use of the product and/or the information and drawings contained herein.
No responsibility is assumed by us for any infringement of a third party's right which may result from the use
thereof.
6. The products listed in this document are intended for use in general electronics equipment for commercial
applications (e.g., office automation, communication equipment, measurement equipment, consumer
electronics, etc.). These products are not autho rized for use in any system or application that requires special
or enhanced quality and reliability characteristics nor in any system or application where the failure of such
system or application may result in the loss or damage of property, or death or injury to humans.
Such applications include, but are not limited to, traffic and automotive equipment, safety devices, aerospace
equipment, nuclear power control, medical equipment, and life-support systems.
7. Certain products in this document may need government approval before they can be exported to particular
countries. The purchaser assumes the responsibility of determining the legality of export of these products
and will take appropriate and necessary steps at their own expense for these.
8. No part of the contents contained herein may be reprinted or reproduced without our prior permission.
9.
Qualification and Reliability
To help ensure high product reliability and customer satisfaction, OKI is committed to an intensive quality
program tha t starts in the design phase and proceeds through the manufacturing process.
Optical transceiver modules are qualified to OKI internal standards using MIL-STD-883 test methods and
procedures and using sample techniques consistent with Telcordia requirements.
This qualification program fully meets the intent of Telcordia reliability practices GR-468-CORE.
10. Laser Safety
All version of transceiver are Class 1 Laser products FDA complies with 21 CFR 1040.10 and 1040.11
requirements.
Also, all versions are Class 1 Laser products pre IEC 825-1
.
Copyright 2002 Oki Electric Industry Co., Ltd.