1
PS8727A 07/07/04
Features
Near-Zero propagation delay
5 switches connect inputs to outputs
High signal passing bandwidth (500 MHz)
Beyond Rail-to-Rail switching
5V I/O tolerant with 3.3V supply in OFF and ON state
2.5V and 3.3V supply voltage operation
Hot Insertion Capable
Industrial Operating Temperature: -40C to +85C
2KV ESD Protection (Human Body Model)
Latch-up Performance > 250mA per JESD17
Packaging (Pb-free & Green available):
16-pin 150-mil wide plastic QSOP (Q)
16-pin 173-mil wide plastic TSSOP (L)
20-Contact TQFN (ZH)
Low Voltage, High-Bandwidth, 3-Channel
2:1 Mux/DeMux, NanoSwitch
TM
Description
Pericom Semiconductor's PI3CH series of switch circuits are
produced using the Company's advanced sub-micron CMOS
technology, achieving industry leading performance.
The PI3CH360 is a 3-Channel, 2:1 Multiplexer/Demultiplexer with
3-state outputs. The switch introduces no additional ground bounce
noise or propagation delay.
The PI3CH360 device is very useful in switching signals that have
high bandwidth (500MHz).
PI3CH360
Pin Configuration
Notes:
1. N.C. = No internal connection
Pin Description
Pin Name
Description
IAN to ICN
Data Inputs
S
Select Inputs
EN
Enable
YA to YC
Data Outputs
GND
Ground
V
CC
Power
Truth Table
(1)
EN
S
YA
YB
YC
Function
H
X
Hi-Z
Hi-Z
Hi-Z
Disable
L
L
IA0
IB0
IC0
S=0
L
H
IA1
IB1
IC1
S=1
Notes:
1. H=High Voltage Level
L=Low Voltage Level
Block Diagram
IA
0
EN
S
IA
1
IB
0
IB
1
IC
0
IC
1
YA
YB
YC
2
PS8727A 07/07/04
PI3CH360
Low Voltage, High-Bandwidth, 3-Channel, 2:1
Mux/DeMux, NanoSwitch
TM
Storage Temperature ................................................ 65C to +150C
Ambient Temperature with Power Applied ............... 40C to +85C
Supply Voltage to Ground Potential ........................... 0.5V to +4.6V
DC Input Voltage ........................................................ 0.5V to +6.0V
DC Output Current................................................................... 120mA
Power Dissipation ....................................................................... 0.5W
Note:
Stresses greater than those listed under MAXIMUM
RATINGS may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these
or any other conditions above those indicated in the operational
sections of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect re-
liability.
Maximum Ratings
(Above which the useful life may be impaired. For user guidelines, not tested.)
DC Electrical Characteristics, 3.3V Supply
(Over Operating Range, T
A
= 40C to +85C, V
CC
= 3.3V 10%)
Parameters
Description
Test Conditions
(1)
Min.
Typ.
(2)
Max. Units
V
IH
Input HIGH Voltage
Guaranteed Logic HIGH Level
2.0
--
--
V
V
IL
Input LOW Voltage
Guaranteed Logic LOW Level
0.5
--
0.8
V
IK
Clamp diode Voltage
V
CC
= Min., I
IN
= 18mA
--
1.3
1.8
I
IH
Input HIGH Current
V
CC
= Max., V
IN
= V
CC
--
--
1
A
I
IL
Input LOW Current
V
CC
= Max., V
IN
= GND
--
--
1
I
OZH
High-Impedence Current
(3)
0 Y, In V
CC
--
--
1
R
ON
Switch On-Resistance
(4)
V
CC
= Min.,V
IN
= 0.0V
I
ON
= 48mA or 64mA
--
4
6
V
CC
= Min., V
IN
= 3.6V, I
ON
= 15mA
--
5
8
DC Electrical Characteristics, 2.5V Supply
(Over Operating Range, T
A
= 40C to +85C, V
CC
= 2.5V 10%)
Parameters
(5)
Description
Test Conditions
Min.
Typ.
Max.
Units
V
IH
Input HIGH Voltage
Guaranteed Logic HIGH Level
1.8
V
CC
+ 0.3
V
V
IL
Inout LOW Voltage
Guaranteed Logic LOW Level
0.3
0.8
V
IK
Clamp Diode Voltage
V
CC
= Max., I
IN
= 6mA
0.7
1.8
I
IH
Input HIGH Current
V
CC
= Max., V
IN
= V
CC
1
A
I
IL
Input LOW Current
V
CC
= Max., V
IN
= GND
1
I
OZH
High Impedance Current
(3)
0 Y, In V
CC
1
R
ON
Switch On-Resistance
(4)
V
CC
= Min., V
IN
=0.0V,
I
ON
= 48mA
6
8
V
CC
= Min., V
IN
= 2.25V,
I
ON
= -15mA
7
14
3
PS8727A 07/07/04
PI3CH360
Low Voltage, High-Bandwidth, 3-Channel, 2:1
Mux/DeMux, NanoSwitch
TM
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device.
2. Typical values are at V
CC
= 3.3V, +25C ambient.
Notes:
1. For Max. or Min. conditions, use appropriate value specified under Electrical Characteristics for the applicable device type.
2. Typical values are at V
CC
= 3.3V, T
A
= 25C ambient and maximum loading.
3. Not more than one output should be shorted at one time. Duration of the test should not exceed one second.
4. Measured by the voltage drop between Y and In pin at indicated current through the switch. ON resistance is determined
by the lower of the voltages on the two (Y, In) pins.
5. This parameter is determined by device characterization but is not production tested.
Capacitance
(T
A
= 25C f = 1 MHz)
Parameters
(5)
Description
Test Conditions
Typ.
Units
C
IN
Input Capacitance
V
IN
= 0V
3.0
pF
C
OFF(IN)
In Capacitance, Switch Off
3.5
C
OFF(Y)
Y Capacitance, Switch Off
7.0
C
ON
Y/In Capacitance, Switch On
10.0
Power Supply Characteristics
Parameters
Description
Test Conditions
(1)
Min. Typ.
(2)
Max.
Units
I
CC
Quiescent Power Supply Current
V
CC
= 3.6V, V
IN
= GND or V
CC
0.8
mA
4
PS8727A 07/07/04
PI3CH360
Low Voltage, High-Bandwidth, 3-Channel, 2:1
Mux/DeMux, NanoSwitch
TM
Switching Characteristics over 2.5V Operating Range
Parameters
Description
Conditions
(1)
Com.
Units
Min.
Max.
t
PLH
t
PHL
Propogation Delay
(2,3)
Y to In, In to Y
See Test Diagram
0.3
ns
t
PZH
t
PZL
Enable Time S or EN to Y or In
See Test Diagram
1.5
15.0
t
PHZ
t
PLZ
Disable Time S or EN to Y or In
1.5
12.0
Switching Characteristics over 3.3V Operating Range
Parameters
Description
Conditions
(1)
Com.
Units
Min.
Typ.
Max.
t
PLH
t
PHL
Propogation Delay
(2,3)
Y to In, In to Y
See Test Diagram
0.3
ns
t
PZH
t
PZL
Enable Time S or EN to Y or In
See Test Diagram
1.5
9.0
t
PHZ
t
PLZ
Disable Time S or EN to Y or In
1.5
9.0
Notes:
1. See test circuit and waveforms.
2. This parameter is guaranteed but not tested on Propagation Delays.
3. The switch contributes no propagational delay other than the RC delay of the On-Resistance of the switch and the load
capacitance. The time constant for the switch alone is of the order of 0.30ns for 10pF load. Since this time constant is much
smaller than the rise/fall times of typical driving signals, it adds very little propagational delay to the system. Propagational
delay of the switch when used in a system is determined by the driving circuit on the driving side of the switch and its
interaction with the load on the driven side.
Dynamic Electrical Characteristics Over the Operating Range
(T
A
= -40 to +85, V
CC
= 3.3V 10%)
Parameter
Description
Test Condition
Min.
Typ.
Max.
Units
X
TALK
Crosstalk
See Test Diagram
-60
dB
O
IRR
Off-Isolation
See Test Diagram
-60
BW
-3dB Bandwidth
See Test Diagram
200
500
MHz
5
PS8727A 07/07/04
PI3CH360
Low Voltage, High-Bandwidth, 3-Channel, 2:1
Mux/DeMux, NanoSwitch
TM
Test Circuit for Electrical Characteristics
(1)
Notes:
1. C
L
= Load capacitance: includes jig and probe capacitance.
2. R
T
= Termination resistance: should be equal to Z
OUT
of the Pulse Generator
3. Waveform 1 is for an output with internal conditions such that the output is low except when disabled by the output control.
Waveform 2 is for an output with internal conditions such that the output is high except when disabled by the output control.
4. All input impulses are supplied by generators having the following characteristics: PRR MHz, Z
O
= 50, t
R
2.5ns, t
F
2.5ns.
5. The outputs are measured one at a time with one transition per measurement.
Test Circuit for Dynamic Electrical Characteristics
RT
10pF
CL
VCC
VIN
VOUT
200
200
6.0V
Pulse
Generator
D.U.T
V
CC
D.U.T
T1
R1
S1
HP11667A
50
10
pF
HP4195A
Switch Positions
Test
Switch
t
PLZ
, t
PZL
6.0V
t
PHZ
, t
PZH
GND
Prop Delay
Open
PDF 
ZIP