Philips Semiconductors

Product specification

83C750/87C750

80C51 8-bit microcontroller family
1K/64 OTP/ROM, low pin count

1998 May 01

8531683 19331

DESCRIPTION

The Philips 8XC750 offers the advantages of the 80C51 architecture
in a small package and at low cost.

The 8XC750 Microcontroller is fabricated with Philips high-density
CMOS technology. Philips epitaxial substrate minimizes CMOS
latch-up sensitivity.

The 87C750 contains a 1k

8 EPROM, a 64

8 RAM, 19 I/O lines,

a 16-bit auto-reload counter/timer, a five-source, fixed-priority level
interrupt structure and an on-chip oscillator.

FEATURES

80C51 based architecture

Oscillator frequency range--up to 16MHz

Small package sizes

24-pin DIP (300 mil "skinny DIP")

24-pin Shrink Small Outline Package

28-pin PLCC

87C750 available in one-time programmable plastic packages

Low power consumption:

Normal operation: less than 11mA @ 5V, 12MHz

Idle mode

Power-down mode

8 EPROM (87C750)

8 RAM

16-bit auto reloadable counter/timer

Boolean processor

CMOS and TTL compatible

Well suited for logic replacement, consumer and industrial
applications

LED drive outputs

PIN CONFIGURATIONS

P3.4/A4

P3.3/A3

P3.2/A2/A10

P3.1/A1/A9

P3.0/A0/A8

P0.2/VPP

RST

P0.0/ASEL

P1.0/D0

P1.1/D1

P1.2/D2

P1.3/D3

P1.4/D4

P1.5/INT0/D5

P1.6/INT1/D6

P1.7/T0/D7

P3.7/A7

P3.6/A6

P3.5/A5

PLASTIC

DUAL

IN-LINE

AND

SHRINK

SMALL

OUTLINE

PACKAGE

PLASTIC

LEADED

CHIP

CARRIER

P0.1/OEPGM

Pin

Function

P3.4/A4

P3.3/A3

P3.2/A2/A10

P3.1/A1/A9

NC*

P3.0/A0/A8

P0.2/V

P0.1/OE-PGM

P0.0/ASEL

NC*

RST

Pin

Function

P1.0/D0

P1.1/D1

P1.2/D2

P1.3/D3

P1.4/D4

P1.5/INT0/D5

NC*

P1.6/INT1/D6

P1.7/T0/D7

P3.7/A7

P3.6/A6

P3.5/A5

SU00295A

* NO INTERNAL CONNECTION

ORDERING INFORMATION

ROM

EPROM

TEMPERATURE RANGE

C AND PACKAGE

FREQUENCY

DRAWING

NUMBER

P83C750EBP N

P87C750EBP N

OTP

0 to +70, Plastic Dual In-line Package

3.5 to 16MHz

SOT222-1

P83C750EFP N

P87C750EFP N

OTP

40 to +85, Plastic Dual In-line Package

3.5 to 16MHz

SOT222-1

P83C750EBA A

P87C750EBA A

OTP

0 to +70, Plastic Lead Chip Carrier

3.5 to 16MHz

SOT261-3

P83C750EFA A

P87C750EFA A

OTP

40 to +85, Plastic Lead Chip Carrier

3.5 to 16MHz

SOT261-3

P83C750EBD DB

P87C750EBD DB

OTP

0 to +70, Shrink Small Outline Package

3.5 to 16MHz

SOT340-1

NOTE:
1. OTP = One Time Programmable EPROM.

Philips Semiconductors

Product specification

83C750/87C750

80C51 8-bit microcontroller family
1K/64 OTP/ROM, low pin count

1998 May 01

PIN DESCRIPTIONS

PIN NO.

MNEMONIC

DIP/

SSOP

LCC

TYPE

NAME AND FUNCTION

Circuit Ground Potential

Supply voltage during normal, idle, and power-down operation.

P0.0-P0.2

8-6

9-7

I/O

Port 0: Port 0 is a 3-bit open-drain, bidirectional port. Port 0 pins that have 1s written to them float,
and in that state can be used as high-impedance inputs. These pins are driven low if the port register
bit is written with a 0. The state of the pin can always be read from the port register by the program.

P0.0, P0.1, and P0.2 are open drain bidirectional I/O pins with the electrical characteristics listed in
the tables that follow. While these differ from "standard TTL" characteristics, they are close enough
for the pins to still be used as general-purpose I/O. Port 0 also provides alternate functions for
programming the EPROM memory as follows:

N/A

(P0.2)  Programming voltage input. (See Note 1.)

OE/PGM (P0.1)  Input which specifies verify mode (output enable) or the program mode.
OE/PGM = 1 output enabled (verify mode).
OE/PGM = 0 program mode.

ASEL (P0.0)  Input which indicates which bits of the EPROM address are applied to port 3.
ASEL = 0 low address byte available on port 3.
ASEL = 1 high address byte available on port 3 (only the three least significant bits are used).

P1.0-P1.7

13-20

15-20,
23, 24

I/O

Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1 pins that have 1s written
to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 1 pins
that are externally pulled low will source current because of the internal pull-ups. (See DC
Electrical Characteristics: I

). Port 1 serves to output the addressed EPROM contents in the verify

mode and accepts as inputs the value to program into the selected address during the program
mode. Port 1 also serves the special function features of the 80C51 family as listed below:

INT0 (P1.5): External interrupt.

INT1 (P1.6): External interrupt.

T0 (P1.7): Timer 0 external input.

P3.0-P3.7

5-1,

23-21

6, 4-1,

27-25

I/O

Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s written
to them are pulled high by the internal pull-ups and can be used as inputs. As inputs, port 3 pins
that are externally being pulled low will source current because of the pull-ups. (See DC Electrical
Characteristics: I

). Port 3 also functions as the address input for the EPROM memory location to

be programmed (or verified). The 10-bit address is multiplexed into this port as specified by
P0.0/ASEL.

RST

Reset: A high on this pin for two machine cycles while the oscillator is running, resets the device.
An internal diffused resistor to V

permits a power-on RESET using only an external capacitor to

. After the device is reset, a 10-bit serial sequence, sent LSB first, applied to RESET, places

the device in the programming state allowing programming address, data and V

to be applied for

programming or verification purposes. The RESET serial sequence must be synchronized with the
X1 input.

Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator circuits.
X1 also serves as the clock to strobe in a serial bit stream into RESET to place the device in the
programming state.

Crystal 2: Output from the inverting oscillator amplifier.

NOTE:
1. When P0.2 is at or close to 0 Volt, it may affect the internal ROM operation. We recommend that P0.2 be tied to V

via a small pull-up (e.g.,

OSCILLATOR CHARACTERISTICS

X1 and X2 are the input and output, respectively, of an inverting
amplifier which can be configured for use as an on-chip oscillator.

To drive the device from an external clock source, X1 should be
driven while X2 is left unconnected. There are no requirements on
the duty cycle of the external clock signal, because the input to the
internal clock circuitry is through a divide-by-two flip-flop. However,
minimum and maximum high and low times specified in the data
sheet must be observed.

RESET

A reset is accomplished by holding the RST pin high for at least two
machine cycles (24 oscillator periods), while the oscillator is running.
To insure a good power-up reset, the RST pin must be high long

enough to allow the oscillator time to start up (normally a few
milliseconds) plus two machine cycles. At power-up, the voltage on
V

and RST must come up at the same time for a proper start-up.

IDLE MODE

In idle mode, the CPU puts itself to sleep while all of the on-chip
peripherals stay active. The instruction to invoke the idle mode is the
last instruction executed in the normal operating mode before the
idle mode is activated. The CPU contents, the on-chip RAM, and all
of the special function registers remain intact during this mode. The
idle mode can be terminated either by any enabled interrupt (at
which time the process is picked up at the interrupt service routine
and continued), or by a hardware reset which starts the processor in
the same manner as a power-on reset.

Philips Semiconductors

Product specification

83C750/87C750

80C51 8-bit microcontroller family
1K/64 OTP/ROM, low pin count

1998 May 01

POWER-DOWN MODE

In the power-down mode, the oscillator is stopped and the
instruction to invoke power-down is the last instruction executed.
Only the contents of the on-chip RAM are preserved. A hardware
reset is the only way to terminate the power-down mode. the control
bits for the reduced power modes are in the special function register
PCON.

Table 1.

External Pin Status During Idle and
Power-Down Modes

MODE

Port 0

Port 1

Port 2

Idle

Data

Power-down

Data

DIFFERENCES BETWEEN THE 8XC750 AND THE
80C51

Program Memory

On the 8XC750, program memory is 1024 bytes long and is not
externally expandable, so the 80C51 instructions MOVX, LJMP, and
LCALL are not implemented. The only fixed locations in program
memory are the addresses at which execution is taken up in
response to reset and interrupts, which are as follows:

Program Memory

Event

Address

Reset

000

External INT0

003

Counter/timer 0

00B

External INT1

013

Counter/Timer Subsystem

Timer/Counter
The 8XC750 has one timers: a 16-bit timer/counter. The 16-bit
timer/counter's operation is similar to mode 2 operation on the
80C51, but is extended to 16 bits. The timer/counter is clocked by
either 1/12 the oscillator frequency or by transitions on the T0 pin.
The C/T pin in special function register TCON selects between
these two modes. When the TCON TR bit is set, the timer/counter is
enabled. Register pair TH and TL are incremented by the clock
source. When the register pair overflows, the register pair is
reloaded with the values in registers RTH and RTL. The value in the
reload registers is left unchanged. See the 83C750 counter/timer
block diagram in Figure 1. The TF bit in special function register

TCON is set on counter overflow and, if the interrupt is enabled, will
generate an interrupt.

TCON Register

MSB

LSB

GATE

C/T

IE0

IT0

IE1

IT1

GATE

1 Timer/counter is enabled only when INT0 pin is high,

and TR is 1.

0 Timer/counter is enabled when TR is 1.

C/T

1 Counter/timer operation from T0 pin.
0 Timer operation from internal clock.

1 Set on overflow of TH.
0 Cleared when processor vectors to interrupt routine

and by reset.

1 Timer/counter enabled.
0 Timer/counter disabled.

IE0

1 Edge detected in INT0.

IT0

1 INT0 is edge triggered.
0 INT0 is level sensitive.

IE1

1 Edge detected on INT1.

IT1

1 INT1 is edge triggered.
0 INT1 is level sensitive.

These flags are functionally identical to the corresponding 80C51
flags, except that there is only one timer on the 83C750 and the
flags are therefore combined into one register.

Note that the positions of the IE0/IT0 and IE1/IT1 bits are
transposed from the positions used in the standard 80C51 TCON
register.

Interrupt Subsystem Fixed Priority

The IP register and the 2-level interrupt system of the 80C51 are
eliminated. Simultaneous interrupt conditions are resolved by a
single-level, fixed priority as follows:

Highest priority:

Pin INT0
Counter/timer flag 0
Pin INT1

Special Function Register Addresses

Special function registers for the 8XC750 are identical to those of
the 80C51, except for the changes listed below:

80C51 special function registers not present in the 8XC750 are
TMOD (89), P2 (A0) and IP (B8). The 80C51 registers TH1 and TL1
are replaced with the 87C750 registers RTH and RTL respectively
(refer to Table 2).

OSC

RTL

RTH

T0 Pin

Gate

INT0 Pin

Int.

C/T = 0

C/T = 1

Reload

SU00300

Figure 1.

83C751 Counter/Timer Block Diagram

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: 83C750

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: 83C750