ChipFind - документация

Электронный компонент: OM3105P

Скачать:  PDF   ZIP

Document Outline

DATA SHEET
Preliminary specification
File under Discrete Semiconductors, SC17
January 1994
DISCRETE SEMICONDUCTORS
Philips Semiconductors
OM3105P
Hybrid integrated circuits for
inductive proximity detectors
January 1994
2
Philips Semiconductors
Preliminary specification
Hybrid integrated circuits for inductive
proximity detectors
OM3105P
FEATURES
Extra small dimensions (3 x 20 mm max.)
Wide supply voltage range (6 to 35 V)
Supply current typical 1.5 mA (output stage
switched off)
High output current (250 mA max.)
RC filter on the supply lines
PNP output transistor protected against transients from
the inductive load
Circuit protected against wrong polarity connection of
the supply voltage
Electronic short-circuit protection
Detection distance adjustable by a chip resistor (R
d
),
type 1206
Only a simple coil in one part is required; e.g. the
OM2860 requires a coil in two parts
Hysteresis adjustable by a chip resistor (R
h
), type 0603,
for using the OM3105P with other then M5 coils
Status of the output is shown by a yellow or red LED
mounted on the substrate surface
The OM3105P is also available without a LED, but with
an output pad for external LED connection
A version with a NPN output transistor is available
(OM3105P).
DESCRIPTION
The OM3105P is a hybrid integrated circuit intended for
inductive proximity detectors in a tubular construction,
especially the M5 hollow stud. The circuit performs a make
function (version 1): when actuated, the current flows
through the load, which can be for example a LED or an
optocoupler. It is also possible to perform a break function
when using version OM3115P.
Available versions:
OM3105P: pnp output; make function
OM3115P: pnp output; break function
OM3105N: npn output; make function
OM3115N: npn output; break function
OM31.5./0: for external LED connection.
QUICK REFERENCE DATA
SYMBOL
PARAMETER
CONDITIONS
TYP.
MAX.
UNIT
V
B
DC supply voltage
6
35
V
I
O
output current
V
B
= 24 V; T
s
= 25
C
-
250
mA
f
sw
operating switching frequency
M5 coil
-
5
kHz
T
s
operating substrate temperature
-
20
+70
C
January 1994
3
Philips Semiconductors
Preliminary specification
Hybrid integrated circuits for inductive
proximity detectors
OM3105P
MECHANICAL DATA
PAD INFORMATION
PAD NUMBER
DESCRIPTION
1
output
2
negative supply (
-
)
3
positive supply (+)
4
coil connection
5
coil connection
6
R
d
resistor (type 1206) for adjusting the detection distance
7
R
t
resistor (type 0603) for adjusting the stability with temperature variations
8
R
h
resistor (type 0603) for adjusting the hysteresis
MSA936 - 1
inductive
load
3
1
20 max
8
7
3
max
5
4
7.75 0.3
6
2
Dimensions in mm.
Coil: 0.063 mm Cu wire, 80 turns.
Potcore: 3.3 x 1.3 mm.
Fig.1 Outline and connections.
January 1994
4
Philips Semiconductors
Preliminary specification
Hybrid integrated circuits for inductive
proximity detectors
OM3105P
LIMITING VALUES
Limiting values in accordance with the Absolute Maximum Rating System (IEC 134).
CHARACTERISTICS
V
B
= 24 V (DC); T
s
= 25
C; unless otherwise specified.
SYMBOL
PARAMETER
MIN.
MAX.
UNIT
V
B
DC supply voltage
6
35
V
I
O
output current; T
s
= 25
C
-
250
mA
T
stg
storage temperature
-
40
+125
C
T
s
operating substrate temperature
-
20
+70
C
SYMBOL
PARAMETER
CONDITIONS
TYP.
MAX.
UNIT
I
B
supply current
output stage ON
11
-
mA
output stage OFF
1.5
-
mA
V
d
voltage drop
I
O
= 250 mA
1
1.5
V
d
detection distance
coil M5
0.8
-
mm
20
80
1.0
0.8
MBD233
0.9
0
20
40
60
d
(mm)
T ( C)
o
s
doff
don
Fig.2
Switching distance as a function of the
substrate temperature.
6
1.0
0.8
MBD235
0.9
12
18
24
30
d
(mm)
V (V)
B
doff
don
Fig.3
Switching distance as a function of the DC
supply voltage.
January 1994
5
Philips Semiconductors
Preliminary specification
Hybrid integrated circuits for inductive
proximity detectors
OM3105P
20
80
400
MBD234
0
20
40
60
I
T ( C)
o
s
O max
(mA)
350
300
250
200
150
Fig.4
Overload protection as a function of the substrate temperature.
MOUNTING RECOMMENDATIONS
General
If a protective cap is incorporated, it should be as thin as
possible, because its thickness "d" forms part of the
operating distance "S".
A brass stud wall should not extend beyond the potcore.
The exact value of "S" with its spread is determined by a
number of variables, e.g.:
value of the adjustment resistor R
x
,
the oscillator coil,
the metal of the actuator,
the material and shape of the housing.
Soldering recommendations
Use normal 60/40 solder.
Use a soldering iron with a fine point.
Soldering time should be kept to a minimum, not
exceeding 2.5 s per soldering point (T
sld
= 250
C
maximum).
The substrate should preferably be pre-heated to a
temperature of 100
C with a minimum of 80
C and a
maximum of 125
C.
Potting recommendations
First cover the hybrid IC with about 0.5 mm of silicone
rubber, let it harden and with the parts inserted in the tube,
fill up the tube with epoxy.
Fig.5 Insertion of potcore in brass tube.
MSB318
d
January 1994
6
Philips Semiconductors
Preliminary specification
Hybrid integrated circuits for inductive
proximity detectors
OM3105P
DEFINITIONS
LIFE SUPPORT APPLICATIONS
These products are not designed for use in life support appliances, devices, or systems where malfunction of these
products can reasonably be expected to result in personal injury. Philips customers using or selling these products for
use in such applications do so at their own risk and agree to fully indemnify Philips for any damages resulting from such
improper use or sale.
Data sheet status
Objective specification
This data sheet contains target or goal specifications for product development.
Preliminary specification
This data sheet contains preliminary data; supplementary data may be published later.
Product specification
This data sheet contains final product specifications.
Limiting values
Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one or
more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation
of the device at these or at any other conditions above those given in the Characteristics sections of the specification
is not implied. Exposure to limiting values for extended periods may affect device reliability.
Application information
Where application information is given, it is advisory and does not form part of the specification.
January 1994
7
Philips Semiconductors
Preliminary specification
Hybrid integrated circuits for inductive
proximity detectors
OM3105P
NOTES
Philips Semiconductors
Philips Semiconductors a worldwide company
Argentina: IEROD, Av. Juramento 1992 - 14.b, (1428)
BUENOS AIRES, Tel. (541)786 7633, Fax. (541)786 9367
Australia: 34 Waterloo Road, NORTH RYDE, NSW 2113,
Tel. (02)805 4455, Fax. (02)805 4466
Austria: Triester Str. 64, A-1101 WIEN, P.O. Box 213,
Tel. (01)60 101-1236, Fax. (01)60 101-1211
Belgium: Postbus 90050, 5600 PB EINDHOVEN, The Netherlands,
Tel. (31)40 783 749, Fax. (31)40 788 399
Brazil: Rua do Rocio 220 - 5
th
floor, Suite 51,
CEP: 04552-903-SO PAULO-SP, Brazil.
P.O. Box 7383 (01064-970).
Tel. (011)829-1166, Fax. (011)829-1849
Canada: INTEGRATED CIRCUITS:
Tel. (800)234-7381, Fax. (708)296-8556
DISCRETE SEMICONDUCTORS: 601 Milner Ave,
SCARBOROUGH, ONTARIO, M1B 1M8,
Tel. (0416)292 5161 ext. 2336, Fax. (0416)292 4477
Chile: Av. Santa Maria 0760, SANTIAGO,
Tel. (02)773 816, Fax. (02)777 6730
Colombia: Carrera 21 No. 56-17, BOGOTA, D.E., P.O. Box 77621,
Tel. (571)217 4609, Fax. (01)217 4549
Denmark: Prags Boulevard 80, PB 1919, DK-2300 COPENHAGEN S,
Tel. (032)88 2636, Fax. (031)57 1949
Finland: Sinikalliontie 3, FIN-02630 ESPOO,
Tel. (9)0-50261, Fax. (9)0-520971
France: 4 rue du Port-aux-Vins, BP317,
92156 SURESNES Cedex,
Tel. (01)4099 6161, Fax. (01)4099 6427
Germany: P.O. Box 10 63 23, 20095 HAMBURG ,
Tel. (040)3296-0, Fax. (040)3296 213
Greece: No. 15, 25th March Street, GR 17778 TAVROS,
Tel. (01)4894 339/4894 911, Fax. (01)4814 240
Hong Kong: 15/F Philips Ind. Bldg., 24-28 Kung Yip St.,
KWAI CHUNG, Tel. (0)4245 121, Fax. (0)4806 960
India: PEICO ELECTRONICS & ELECTRICALS Ltd.,
Components Dept., Shivsagar Estate, Block 'A',
Dr. Annie Besant Rd., Worli, BOMBAY 400 018,
Tel. (022)4938 541, Fax. (022)4938 722
Indonesia: Philips House, Jalan H.R. Rasuna Said Kav. 3-4,
P.O. Box 4252, JAKARTA 12950,
Tel. (021)5201 122, Fax. (021)5205 189
Ireland: Newstead, Clonskeagh, DUBLIN 14,
Tel. (01)640 000, Fax. (01)640 200
Italy: Viale F. Testi, 327, 20162 MILANO,
Tel. (02)6752.1, Fax. (02)6752.3350
Japan: Philips Bldg 13-37, Kohnan 2 -chome, Minato-ku, KOKIO 108,
Tel. (03)3740 5101, Fax. (03)3740 0570
Korea: (Republic of) Philips House, 260-199 Itaewon-dong,
Yongsan-ku, SEOUL, Tel. (02)794-5011, Fax. (02)798-8022
Malaysia: No. 76 Jalan Universiti, 46200 PETALING JAYA,
SELANGOR, Tel. (03)757 5511, Fax. (03)757 4880
Mexico: Philips Components, 5900 Gateway East, Suite 200,
EL PASO, TX 79905, Tel. 9-5(800)234-7381, Fax. (708)296-8556
Netherlands: Postbus 90050, 5600 PB EINDHOVEN,
Tel. (040)78 37 49, Fax. (040)78 83 99
New Zealand: 2 Wagener Place, C.P.O. Box 1041, AUCKLAND,
Tel. (09)849-4160, Fax. (09)849-7811
Norway: Box 1, Manglerud 0612, OSLO,
Tel. (22)74 8000, Fax. (22)74 8341
Pakistan: Philips Markaz, M.A. Jinnah Rd., KARACHI 3,
Tel. (021)577 039, Fax. (021)569 1832
Philippines: PHILIPS SEMICONDUCTORS PHILIPPINES Inc,
106 Valero St. Salcedo Village, P.O. Box 911, MAKATI,
Metro MANILA, Tel. (02)810 0161, Fax. (02)817 3474
Portugal: Av. Eng. Duarte Pacheco 6, 1009 LISBOA Codex,
Tel. (01)683 121, Fax. (01)658 013
Singapore: Lorong 1, Toa Payoh, SINGAPORE 1231,
Tel. (65)350 2000, Fax. (65)251 6500
South Africa: 195-215 Main Road, Martindale,
P.O. Box 7430,JOHANNESBURG 2000,
Tel. (011)470-5433, Fax. (011)470-5494
Spain: Balmes 22, 08007 BARCELONA,
Tel. (03)301 6312, Fax. (03)301 42 43
Sweden: Kottbygatan 7, Akalla. S-164 85 STOCKHOLM,
Tel. (0)8-632 2000, Fax. (0)8-632 2745
Switzerland: Allmendstrasse 140, CH-8027 ZRICH,
Tel. (01)488 2211, Fax. (01)481 7730
Taiwan: 69, Min Sheng East Road, Sec 3, P.O. Box 22978,
TAIPEI 10446, Tel. (2)509 7666, Fax. (2)500 5899
Thailand: PHILIPS ELECTRONICS (THAILAND) Ltd.,
60/14 MOO 11, Bangna - Trad Road Km. 3
Prakanong, BANGKOK 10260,
Tel. (2)399-3280 to 9, (2)398-2083, Fax. (2)398-2080
Turkey: Talatpasa Cad. No. 5, 80640 LEVENT/ISTANBUL,
Tel. (0212)279 2770, Fax. (0212)269 3094
United Kingdom: Philips Semiconductors Limited, P.O. Box 65,
Philips House, Torrington Place, LONDON, WC1E 7HD,
Tel. (071)436 41 44, Fax. (071)323 03 42
United States: INTEGRATED CIRCUITS:
811 East Arques Avenue, SUNNYVALE, CA 94088-3409,
Tel. (800)234-7381, Fax. (708)296-8556
DISCRETE SEMICONDUCTORS: 2001 West Blue Heron Blvd.,
P.O. Box 10330, RIVIERA BEACH, FLORIDA 33404,
Tel. (800)447-3762 and (407)881-3200, Fax. (407)881-3300
Uruguay: Coronel Mora 433, MONTEVIDEO,
Tel. (02)70-4044, Fax. (02)92 0601
For all other countries apply to: Philips Semiconductors,
International Marketing and Sales, Building BAF-1,
P.O. Box 218, 5600 MD, EINDHOVEN, The Netherlands,
Telex 35000 phtcnl, Fax. +31-40-724825
SCD27
Philips Electronics N.V. 1993
All rights are reserved. Reproduction in whole or in part is prohibited without the
prior written consent of the copyright owner.
The information presented in this document does not form part of any quotation
or contract, is believed to be accurate and reliable and may be changed without
notice. No liability will be accepted by the publisher for any consequence of its
use. Publication thereof does not convey nor imply any license under patent- or
other industrial or intellectual property rights.
Printed in The Netherlands
9397 726 50011