ChipFind - документация

Электронный компонент: P87C575EBAA

Скачать:  PDF   ZIP
Philips
Semiconductors
80C575/83C575/87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator,
failure detect circuitry, watchdog timer
Product specification
Supersedes data of 1998 Jan 27
IC20 Data Handbook
1998 May 01
INTEGRATED CIRCUITS
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
2
1998 May 01
853-1684 19332
DESCRIPTION
The Philips 80C575/83C575/87C575 is a
high-performance microcontroller fabricated
with Philips high-density CMOS technology.
The Philips CMOS technology combines the
high speed and density characteristics of
HMOS with the low power attributes of
CMOS. Philips epitaxial substrate minimizes
latch-up sensitivity.
The 8XC575 contains an 8k
8 ROM
(83C575) EPROM (87C575), a 256
8 RAM,
32 I/O lines, three 16-bit counter/timers, a
Programmable Counter Array (PCA), a
seven-source, two-priority level nested
interrupt structure, an enhanced UART, four
analog comparators, power-fail detect and
oscillator fail detect circuits, and on-chip
oscillator and clock circuits.
In addition, the 8XC575 has a low active
reset, and the port pins are reset to a low
level. There is also a fully configurable
watchdog timer, and internal power on clear
circuit. The part includes idle mode and
power-down mode states for reduced power
consumption.
FEATURES
80C51 based architecture
8k
8 ROM (83C575)
8k
8 EPROM (87C575)
ROMless (80C575)
256
8 RAM
Three 16-bit counter/timers
Programmable Counter Array
Enhanced UART
Boolean processor
Oscillator fail detect
Low active reset
Asynchronous low port reset
Schmitt trigger inputs
4 analog comparators
Watchdog timer
Low V
CC
detect
Memory addressing capability
64k ROM and 64k RAM
Power control modes:
Idle mode
Power-down mode
CMOS and TTL compatible
4.0 to 16MHz
Extended temperature ranges
OTP package available
PIN CONFIGURATIONS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
CMP0+/P1.0/T2
CMP0-/P1.1/T2EX
ECI/P1.2
CMP0/CEX0/P1.3
CMP1/CEX1/P1.4
CMP2/CEX2/P1.5
CMP3/CEX3/P1.6
RST
RxD/P3.0
TxD/P3.1
INT0/P3.2
INT1/P3.3
CMPR-/T0/P3.4
CMP1+/T1/P3.5
CEX4/P1.7
CMP2+/WR/P3.6
CMP3+/RD/P3.7
XTAL2
XTAL1
VSS
P2.0/A8
P2.1/A9
P2.2/A10
P2.3/A11
P2.4/A12
P2.5/A13
P2.6/A14
P2.7/A15
PSEN
ALE/PROG
EA/VPP
P0.7/AD7
P0.6/AD6
P0.5/AD5
P0.4/AD4
P0.3/AD3
P0.2/AD2
P0.1/AD1
P0.0/AD0
VDD
PQFP
6
44
1
40
34
1
7
17
11
39
33
29
23
12
18
28
22
DUAL
IN-LINE
PACKAGE
LCC
SU00234
ORDERING INFORMATION
ROMless
ROM
EPROM
1
TEMPERATURE RANGE
C AND PACKAGE
FREQ
(MHz)
DRAWING
NUMBER
P80C575EBP N
P83C575EBP N
P87C575EBPN
OTP
0 to +70, 40-Pin Plastic Dual In-line Package
16
SOT129-1
P80C575EBA A
P83C575EBA A
P87C575EBAA
OTP
0 to +70, 44-Pin Plastic Leaded Chip Carrier
16
SOT187-2
P80C575EHAA
P83C575EHAA
P87C575EHAA
OTP
40 to +125, 44-Pin Plastic Leaded Chip Carrier
16
SOT187-2
P80C575EBB B
P83C575EBB B
P87C575EBBB
OTP
0 to +70, 44-Pin Plastic Quad Flat Pack
16
SOT307-2
NOTE:
1. OTP - One Time Programmable EPROM.
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
3
BLOCK DIAGRAM
PSEN
EA
ALE
RST
XTAL1
XTAL2
VCC
VSS
PORT 0
DRIVERS
PORT 2
DRIVERS
RAM ADDR
REGISTER
RAM
PORT 0
LATCH
PORT 2
LATCH
ROM/
EPROM
REGISTER
B
ACC
TMP2
TMP1
ALU
TIMING
AND
CONTROL
INSTRUCTION
REGISTER
PD
OSCILLATOR
PSW
PORT 1
LATCH
PORT 3
LATCH
PORT 1
DRIVERS
PORT 3
DRIVERS
PROGRAM
ADDRESS
REGISTER
BUFFER
PC
INCRE-
MENTER
PROGRAM
COUNTER
DPTR
P1.0-P1.7
P3.0-P3.7
P0.0-P0.7
P2.0-P2.7
STACK
POINTER
SFRs
TIMERS
PCA
SU00238
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
4
CERAMIC AND PLASTIC LEADED
CHIP CARRIER PIN FUNCTIONS
LCC
6
1
40
7
17
39
29
18
28
Pin
Function
1
NC*
2
T2/P1.0/CMP0+
3
T2EX/P1.1/CMP0
4
P1.2/ECI
5
P1.3/CMP0/CEX0
6
P1.4/CMP1/CEX1
7
P1.5/CMP2/CEX2
8
P1.6/CMP3/CEX3
9
P1.7/CEX4
10
RST
11
RxD/P3.0
12
NC*
13
TxD/P3.1
14
INT0/P3.2
15
INT1/P3.3
16
T0/P3.4/CMPR
17
T1/P3.5/CMP1+
18
WR/P3.6/CMP2+
19
RD/P3.7/CMP3+
20
XTAL2
21
XTAL1
22
V
SS
Pin
Function
23
NC*
24
P2.0/A8
25
P2.1/A9
26
P2.2/A10
27
P2.3/A11
28
P2.4/A12
29
P2.5/A13
30
P2.6/A14
31
P2.7/A15
32
PSEN
33
ALE/PROG
34
NC*
35
EA/V
PP
36
P0.7/AD7
37
P0.6/AD6
38
P0.5/AD5
39
P0.4/AD4
40
P0.3/AD3
41
P0.2/AD2
42
P0.1/AD1
43
P0.0/AD0
44
V
CC
SU00235
* NO INTERNAL CONNECTION
PLASTIC QUAD FLAT PACK
PIN FUNCTIONS
PQFP
44
34
1
11
33
23
12
22
SU00236
Pin
Function
1
P1.5/CMP2/CEX2
2
P1.6/CMP3/CEX3
3
P1.7/CEX4
4
RST
5
RxD/P3.0
6
NC*
7
TxD/P3.1
8
INT0/P3.2
9
INT1/P3.3
10
T0/P3.4/CMPR
11
T1/P3.5/CMP1+
12
WR/P3.6/CMP2+
13
RD/P3.7CMP3+
14
XTAL2
15
XTAL1
16
V
SS
17
NC*
18
P2.0/A8
19
P2.1/A9
20
P2.2/A10
21
P2.3/A11
22
P2.4/A12
Pin
Function
23
P2.5/A13
24
P2.6/A14
25
P2.7/A15
26
PSEN
27
ALE/PROG
28
NC*
29
EA/V
PP
30
P0.7/AD7
31
P0.6/AD6
32
P0.5/AD5
33
P0.4/AD4
34
P0.3/AD3
35
P0.2/AD2
36
P0.1/AD1
37
P0.0/AD0
38
V
CC
39
NC*
40
T2/P1.0/CMP0+
41
T2EX/P1.1/CMP0
42
P1.2/ECI
43
P1.3/CMP0/CEX0
44
P1.4/CMP1/CEX1
* NO INTERNAL CONNECTION
LOGIC SYMBOL
POR
T
0
POR
T
1
POR
T
2
POR
T
3
ADDRESS AND
DATA BUS
ADDRESS BUS
T2
T2EX
RxD
TxD
INT0
INT1
T0
T1
WR
RD
SECONDAR
Y
FUNCTIONS
RST
EA/VPP
PSEN
ALE/PROG
VSS
VCC
XTAL1
XTAL2
CMPR
CMP1+
CMP2+
CMP3+
CMP0+
CMP0
ECI
CMP0/CEX0
CMP1/CEX1
CMP2/CEX2
CMP3/CEX3
CEX4
SU00237
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
5
PIN DESCRIPTIONS
PIN NUMBER
MNEMONIC
DIP
LCC
QFP
TYPE
NAME AND FUNCTION
V
SS
20
22
16
I
Ground: 0V reference.
V
CC
40
44
38
I
Power Supply: This is the power supply voltage for normal, idle, and power-down
operation.
P0.0-0.7
39-32
43-36
37-30
I/O
Port 0: Port 0 is an open-drain bidirectional I/O port. Port 0 pins that have 1s written to them
float and can be used as high-impedance inputs. Port 0 is also the multiplexed low-order
address and data bus during accesses to external program and data memory. In this
application, it uses strong internal pull-ups when emitting 1s. Port 0 also receives code
bytes during EPROM programming and outputs code bytes during program verification.
External pull-ups are required during program verification. During reset, port 0 will be
asynchronously driven low and will remain low until written to by software. All port 0 pins
have Schmitt trigger inputs with 200mV hysteresis. A weak pulldown on port 0 guarantees
positive leakage current (see DC Electrical Characteristics: I
L1
).
P1.0-P1.7
1-8
2-9
40-44
1-3
I/O
Port 1: Port 1 is an 8-bit bidirectional I/O port. Port 1 pins have internal pull-ups such that
pins that have 1s written to them can be used as inputs but will source current when
externally pulled low (see DC Electrical Characteristics: I
IL
). Port 1 receives the low-order
address byte during program memory verification and EPROM programming. During reset,
port 1 will be asynchronously driven low and will remain low until written to by software. All
port 1 pins have Schmitt trigger inputs with 50mV hysteresis. Port 1 pins also serve
alternate functions as follows:
1
2
40
I/O
P1.0
T2
Timer 2 external I/O clockout (programmable)
CMP0+
Comparator 0 positive input
2
3
41
I
P1.1
T2EX
Timer 2 capture input
CMP0-
Comparator 0 negative input
3
4
42
I
P1.2
ECI
PCA count input
4
5
43
I/O
P1.3
CEX0
PCA module 0 external I/O
CMP0
Comparator 0 output
5
6
44
I/O
P1.4
CEX1
PCA module 1 external I/O
CMP1
Comparator 1 output
6
7
1
I/O
P1.5
CEX2
PCA module 2 external I/O
CMP2
Comparator 2 output
7
8
2
I/O
P1.6
CEX3
PCA module 3 external I/O
CMP3
Comparator 3 output
8
9
3
I/O
P1.7
CEX4
PCA module 4 external I/O
P2.0-P2.7
21-28
24-31
18-25
I/O
Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that have 1s
written to them can be used as inputs, but will source current when externally pulled low
(see DC Electrical Characteristics: I
IL
). Port 2 emits the high-order address byte during
accesses to external program and data memory that use 16-bit addresses (MOVX
@DPTR). In this application, it uses strong internal pull-ups when emitting 1s. Port 2
receives the high-order address byte during program verification and EPROM programming.
During reset, port 2 will be asynchronously driven low and will remain low until written to by
software. Port 2 can be made open drain by writing to the P2OD register (AIH). In open
drain mode, weak pulldowns on port 2 guarantee positive leakage current (see DC
Electrical Characteristics I
L1
).
P3.0-P3.7
10-17
11,
13-19
5,
7-13
I/O
Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins except P3.1
that have 1s written to them can be used as inputs but will source current when externally
pulled low (see DC Electrical Characteristics: I
IL
). P3.1 will be a high impedance pin except
while transmitting serial data, in which case the strong pull-up will remain on continuously
when outputting a 1 level. The P3.1 output drive level when transmitting can be set to one of
two levels by the writing to the P3.1 register bit. During reset all pins (except P3.1) will be
asynchronously driven low and will remain low until written to by software. All port 3 pins
have Schmitt trigger inputs with 200mV hysteresis, except P3.2 and P3.3, which have 50mV
hysteresis. Port 3 pins serve alternate functions as follows:
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
6
PIN DESCRIPTIONS (Continued)
PIN NUMBER
MNEMONIC
DIP
LCC
QFP
TYPE
NAME AND FUNCTION
Port 3: (continued)
10
11
5
I
P3.0
RxD
Serial receive port
11
13
7
O
P3.1
TxD
Serial transmit port enabled only when transmitting serial data
12
14
8
I
P3.2
INT0
External interrupt 0
13
15
9
I
P3.3
INT1
External interrupt 1
14
16
10
I
P3.4
T0
Timer/counter 0 input
CMPR-
Common - reference to comparators 1, 2, 3
15
17
11
I
P3.5
T1
Timer/counter 1 input
CMP1+
Comparator 1 positive input
16
18
12
O
P3.6
WR
External data memory write strobe
CMP2+
Comparator 2 positive input
17
19
13
O
P3.7
RD
External data memory read strobe
CMP3+
Comparator 3 positive input
RST
9
10
4
I
Reset: A low on this pin asynchronously resets all port pins to a low state except P3.1. The
pin must be held low with the oscillator running for 24 oscillator cycles to initialize the
internal registers. An internal diffused resistor to V
CC
permits a power on reset using only
an external capacitor to V
SS
. RST has a Schmitt trigger input stage to provide additional
noise immunity with a slow rising input voltage.
ALE/PROG
30
33
27
I/O
Address Latch Enable/Program Pulse: Output pulse for latching the low byte of the
address during an access to external memory. In normal operation, ALE is emitted at a
constant rate of 1/6 the oscillator frequency, and can be used for external timing or clocking.
Note that one ALE pulse is skipped during each access to external data memory. ALE is
switched off if the bit 0 in the AUXR register (8EH) is set. This pin is also the program pulse
input (PROG) during EPROM programming.
PSEN
29
32
26
O
Program Store Enable: The read strobe to external program memory. When the device is
executing code from the external program memory, PSEN is activated twice each machine
cycle, except that two PSEN activations are skipped during each access to external data
memory. PSEN is not activated during fetches from internal program memory.
EA/V
PP
31
35
29
I
External Access Enable/Programming Supply Voltage: EA must be externally held low
to enable the device to fetch code from external program memory locations 0000H to
1FFFH. If EA is held high, the device executes from internal program memory unless the
program counter contains an address greater than 1FFFH. This pin also receives the
12.75V programming supply voltage (V
PP
) during EPROM programming.
XTAL1
19
21
15
I
Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator
circuits.
XTAL2
18
20
14
O
Crystal 2: Output from the inverting oscillator amplifier.
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
7
Table 1.
87C575 Special Function Registers
SYMBOL
DESCRIPTION
DIRECT
ADDRESS
BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION
MSB
LSB
RESET
VALUE
ACC*
Accumulator
E0H
E7
E6
E5
E4
E3
E2
E1
E0
00H
AUXR#
Auxiliary
8EH
LO
AO
xxxxxx00B
B*
B register
F0H
F7
F6
F5
F4
F3
F2
F1
F0
00H
CCAP0H#
Module 0 Capture High
FAH
xxxxxxxxB
CCAP1H#
Module 1 Capture High
FBH
xxxxxxxxB
CCAP2H#
Module 2 Capture High
FCH
xxxxxxxxB
CCAP3H#
Module 3 Capture High
FDH
xxxxxxxxB
CCAP4H#
Module 4 Capture High
FEH
xxxxxxxxB
CCAP0L#
Module 0 Capture Low
EAH
xxxxxxxxB
CCAP1L#
Module 1 Capture Low
EBH
xxxxxxxxB
CCAP2L#
Module 2 Capture Low
ECH
xxxxxxxxB
CCAP3L#
Module 3 Capture Low
EDH
xxxxxxxxB
CCAP4L#
Module 4 Capture Low
EEH
xxxxxxxxB
CCAPM0#
Module 0 Mode
DAH
ECOM
CAPP
CAPN
MAT
TOG
PWM
ECCF
x0000000B
CCAPM1#
Module 1 Mode
DBH
ECOM
CAPP
CAPN
MAT
TOG
PWM
ECCF
x0000000B
CCAPM2#
Module 2 Mode
DCH
ECOM
CAPP
CAPN
MAT
TOG
PWM
ECCF
x0000000B
CCAPM3#
Module 3 Mode
DDH
ECOM
CAPP
CAPN
MAT
TOG
PWM
ECCF
x0000000B
CCAPM4#
Module 4 Mode
DEH
ECOM
CAPP
CAPN
MAT
TOG
PWM
ECCF
x0000000B
DF
DE
DD
DC
DB
DA
D9
D8
CCON*#
PCA Counter Control
D8H
CF
CR
CCF4
CCF3
CCF2
CCF1
CCF0
00x00000B
CH#
PCA Counter High
F9H
00H
CL#
PCA Counter Low
E9H
00H
CMOD#
PCA Counter Mode
D9H
CIDL
WDTE
CPS1
CPS0
ECF
00xxx000B
EF
EE
ED
EC
EB
EA
E9
E8
CMP*#
Comparator
E8H
EC3DP
EC2DP
EC1DP
EC0DP
C3RO
C2RO
C1RO
C0RO
00H
CMPE#
Comparator Enable
91H
EC3TDC
EC2TDC
EC1TDC
EC0TDC
EC3OD
EC2OD
EC1OD
EC0OD
00H
DPTR:
Data Pointer (2 bytes)
DPH
Data Pointer High
83H
00H
DPL
Data Pointer Low
82H
00H
AF
AE
AD
AC
AB
AA
A9
A8
IE*
Interrupt Enable
A8H
EA
EC
ET2
ES
ET1
EX1
ET0
EX0
00H
BF
BE
BD
BC
BB
BA
B9
B8
IP*
Interrupt Priority
B8H
PPC
PT2
PS
PT1
PX1
PT0
PX0
x0000000B
87
86
85
84
83
82
81
80
P0*
Port 0
80H
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
00H
97
96
95
94
93
92
91
90
P1*
Port 1
90H
CEX4
CEX3
CEX2
CEX1
CEX0
EXI
T2EX
T2
00H
A7
A6
A5
A4
A3
A2
A1
A0
P2*
Port 2
A0H
AD15
AD14
AD13
AD12
AD11
AD10
AD9
AD8
00H
B7
B6
B5
B4
B3
B2
B1
B0
P3*
Port 3
B0H
RD
WR
T1
T0
INT1
INT0
TxD
RxD
00H
*
SFRs are bit addressable.
#
SFRs are modified from or added to the 80C51 SFRs.
1. 87C575 only.
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
8
Table 1.
87C575 Special Function Registers (Continued)
SYMBOL
DESCRIPTION
DIRECT
ADDRESS
BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION
MSB
LSB
RESET
VALUE
P2OD#
Port 2 Pullup Disable
A1H
00H
PCON#
Power Control
87H
SMOD1
SMOD0
OSF
1
POF
1
LVF
1
GF0
PD
IDL
00xxx000B
D7
D6
D5
D4
D3
D2
D1
D0
PSW*
Program Status Word
D0H
CY
AC
F0
RS1
RS0
OV
P
00H
RACAP2H#
Timer 2 Capture High
CBH
00H
RACAP2L#
Timer 2 Capture Low
CAH
00H
SADDR#
Slave Address
A9H
00H
SADEN#
Slave Address Mask
B9H
00H
SBUF
Serial Data Buffer
99H
xxxxxxxxB
9F
9E
9D
9C
9B
9A
99
98
SCON*
Serial Control
98H
SM0
SM1
SM2
REN
TB8
RB8
TI
RI
00H
SP
Stack Pointer
81H
07H
8F
8E
8D
8C
8B
8A
89
88
TCON*
Timer Control
88H
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
00H
CF
CE
CD
CC
CB
CA
C9
C8
T2CON*
Timer 2 Control
C8H
TF2
EXF2
RCLK
TCLK
EXEN2
TR2
C/T2
CP/RL2
00H
T2MOD#
Timer 2 Mode Control
C9H
T2OE
2
DCEN
xxxxxxx0B
TH0
Timer High 0
8CH
00H
TH1
Timer High 1
8DH
00H
TH2#
Timer High 2
CDH
00H
TL0
Timer Low 0
8AH
00H
TL1
Timer Low 1
8BH
00H
TL2#
Timer Low 2
CCH
00H
TMOD
Timer Mode
89H
GATE
C/T
M1
M0
GATE
C/T
M1
M0
00H
C7
C6
C5
C4
C3
C2
C1
C0
WDCON*#
Watchdog Timer Control
C0H
PRE2
PRE1
PRE0
LVRE
OFRE
WDRUN
WDTOF
WDMOD
11111101B
WDL#
Watchdog Timer Reload
C1H
00H
WFEED1#
Watchdog Feed 1
C2H
xxH
WFEED2#
Watchdog Feed 2
C3H
xxH
*
SFRs are bit addressable.
#
SFRs are modified from or added to the 80C51 SFRs.
1. Reset value depends on reset source.
2. Programmable clock-out.
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
9
POWER ON CLEAR/
POWER ON FLAG
An on-chip Power On Detect Circuit resets
the 8XC575 and sets the Power Off Flag
(PCON.4) on power up or if V
CC
drops to
zero momentarily. The POF can only be
cleared by software. The RST pin is not
driven by the power on detect circuit. The
POF can be read by software to determine
that a power failure has occurred and can
also be set by software.
LOW VOLTAGE DETECT
An on-chip Low Voltage Detect circuit sets
the Low Voltage Flag (PCON.3) if V
CC
drops
below V
LOW
(see DC Electrical
Characteristics) and resets the 8XC575 if the
Low Voltage Reset Enable bit (WDCON.4) is
set. If the LVRE is cleared, the reset is
disabled but LVF will still be set if V
CC
is low.
The RST pin is not driven by the low voltage
detect circuit. The LVF can be read by
software to determine that V
CC
was low. The
LVF can be set or cleared by software.
OSCILLATOR FAIL DETECT
An on-chip Oscillator Fail Detect circuit sets
the Oscillator Fail Flag (PCON.5) if the
oscillator frequency drops below OSCF for
one or more cycles (see AC Electrical
Characteristics: OSCF) and resets the
8XC575 if the Oscillator Fail Reset Enable bit
(WDCON.3) is set. If OFRE is cleared, the
reset is disabled but OSF will still be set if the
oscillator fails. The RST pin is not driven by
the oscillator fail detect circuit. The OSF can
be read by software to determine that an
oscillator failure has occurred. The OSF can
be set or cleared by software.
LOW ACTIVE RESET
One of the most notable features on this part
is the low active reset. At this time this is the
only 80C51 derivative available that has low
active reset. This feature makes it easier to
interface the 8XC575 into an application to
accommodate the power-on and low voltage
conditions that can occur. The low active
reset operates exactly the same as high
active reset with the exception that the part is
put into the reset mode by applying a low
level to the reset pin. For power-on reset it is
also necessary to invert the power-on reset
circuit; connecting the 8.2K resistor from the
reset pin to V
CC
and the 10
f capacitor from
the reset pin to ground. Figure 1 shows all of
the reset related circuitry.
When reset the port pins on the 87C575 are
driven low asynchronously. This is different
from all other 80C51 derivatives.
The 8XC575 also has Low voltage detection
circuitry that will, if enabled, force the part to
reset when V
CC
(on the part) fails below a set
level. Low Voltage Reset is enabled by a
normal reset. Low Voltage Reset can be
disabled by clearing LVRE (bit 4 in the
WDCON SFR) then executing a watchdog
feed sequence (A5H to WFEED1 followed
immediately by 5A to WFEED2). In addition
there is a flag (LVF) that is set if a low voltage
condition is detected. The LVF flag is set
even if the Low Voltage detection circuitry is
disabled. Notice that the Low voltage
detection circuitry does not drive the RST#
pin so the LVF flag is the only way that the
microcontroller can determine if it has been
reset due to a low voltage condition.
The 8XC575 has an on-chip power-on
detection circuit that sets the POF (PCON.4)
flag on power up or if the V
CC
level
momentarily drops to 0V. This flag can be
used to determine if the part is being started
from a power-on (cold start) or if a reset has
occurred due to another condition (warm
start).
TIMERS
The 87C575 has four on-chip timers.
Timers 0 and 1 are identical in every way to
Timers 0 and 1 on the 80C51.
Timer 2 on the 8XC575 is identical to the
80C52 Timer 2 (described in detail in the
80C52 overview) with the exception that it is
an up or down counter. To configure the
Timer to count down the DCEN bit in the
T2MOD special function register must be set
and a low level must be present on the T2EX
pin (P1.1).
The Watchdog timer operation and
implementation is the same as that for the
8XC550 (described in the 8XC550 overview)
with the exception that the reset values of the
WDCON and WDL special function registers
have been changed. The changes in these
registers cause the watchdog timer to be
enabled with a timeout of 98304
T
OSC
when the part is reset. The watchdog can be
disabled by executing a valid feed sequence
and then clearing WDRUN (bit 2 in the
WDCON SFR).
PRE2
PRE1
PRE0
LVRE
OFRE
WDRUN
WDTOF
WDMOD
WDCON
(C0H)
SHADOW REGISTER
FOR WDCON
WATCHDOG FEED
SMOD1
SMOD0
OSF
LVF
GF0
GF1
IDL
PCON
(87GH)
OSC FREQ BELOW OSCF
(MIN FREQUENCY)
RST
+
V
CC
VLOW
(LOW V
CC
REFERENCE)
POWER-ON DETECT
PCA WATCHDOG
WATCHDOG TIMER
8xC575
INTERNAL
RESET
POF
SU00239
Figure 1. Reset Circuitry
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
10
PROGRAMMABLE COUNTER
ARRAY (PCA)
The Programmable Counter Array is a
special Timer that has five 16-bit
capture/compare modules associated with it.
Each of the modules can be programmed to
operate in one of four modes: rising and/or
falling edge capture, software timer,
high-speed output, or pulse width modulator.
Each module has a pin associated with it in
port 1. Module 0 is connected to P1.3(CEX0),
module 1 to P1.4(CEX1), etc.. The basic
PCA configuration is shown in Figure 2.
The PCA timer is a common time base for all
five modules and can be programmed to run
at: 1/12 the oscillator frequency, 1/4 the
oscillator frequency, the Timer 0 overflow, or
the input on the ECI pin (P1.2). The timer
count source is determined from the CPS1
and CPS0 bits in the CMOD SFR as follows
(see Figure 3):
CPS1 CPS0 PCA Timer Count Source
0
0
1/12 oscillator frequency
0
1
1/4 oscillator frequency
1
0
Timer 0 overflow
1
1
External Input at ECI pin
In the CMOD SFR are three additional bits
associated with the PCA. They are CIDL
which allows the PCA to stop during idle
mode, WDTE which enables or disables the
watchdog function on module 4, and ECF
which when set causes an interrupt and the
PCA overflow flag CF (in the CCON SFR) to
be set when the PCA timer overflows. These
functions are shown in Figure 3.
The watchdog timer function is implemented
in module 4 as implemented in other parts
that have a PCA that are available on the
market. However, if a watchdog timer is
required in the target application, it is
recommended to use the hardware watchdog
timer that is implemented on the 87C575
separately from the PCA (see Figure 14).
The CCON SFR contains the run control bit
for the PCA and the flags for the PCA timer
(CF) and each module (refer to Figure 6). To
run the PCA the CR bit (CCON.6) must be
set by software. The PCA is shut off by
clearing this bit. The CF bit (CCON.7) is set
when the PCA counter overflows and an
interrupt will be generated if the ECF bit in
the CMOD register is set, The CF bit can only
be cleared by software. Bits 0 through 4 of
the CCON register are the flags for the
modules (bit 0 for module 0, bit 1 for module
1, etc.) and are set by hardware when either
a match or a capture occurs. These flags
also can only be cleared by software. The
PCA interrupt system shown in Figure 4.
Each module in the PCA has a special
function register associated with it. These
registers are: CCAPM0 for module 0,
CCAPM1 for module 1, etc. (see Figure 7).
The registers contain the bits that control the
mode that each module will operate in. The
ECCF bit (CCAPMn.0 where n=0, 1, 2, 3, or
4 depending on the module) enables the CCF
flag in the CCON SFR to generate an
interrupt when a match or compare occurs in
the associated module. PWM (CCAPMn.1)
enables the pulse width modulation mode.
The TOG bit (CCAPMn.2) when set causes
the CEX output associated with the module to
toggle when there is a match between the
PCA counter and the module's
capture/compare register. The match bit MAT
(CCAPMn.3) when set will cause the CCFn
bit in the CCON register to be set when there
is a match between the PCA counter and the
module's capture/compare register.
The next two bits CAPN (CCAPMn.4) and
CAPP (CCAPMn.5) determine the edge that
a capture input will be active on. The CAPN
bit enables the negative edge, and the CAPP
bit enables the positive edge. If both bits are
set both edges will be enabled and a capture
will occur for either transition. The last bit in
the register ECOM (CCAPMn.6) when set
enables the comparator function. Figure 8
shows the CCAPMn settings for the various
PCA functions.
There are two additional registers associated
with each of the PCA modules. They are
CCAPnH and CCAPnL and these are the
registers that store the 16-bit count when a
capture occurs or a compare should occur.
When a module is used in the PWM mode
these registers are used to control the duty
cycle of the output.
PCA Capture Mode
To use one of the PCA modules in the
capture mode either one or both of the
CCAPM bits CAPN and CAPP for that
module must be set. The external CEX input
for the module (on port 1) is sampled for a
transition. When a valid transition occurs the
PCA hardware loads the value of the PCA
counter registers (CH and CL) into the
module's capture registers (CCAPnL and
CCAPnH). If the CCFn bit for the module in
the CCON SFR and the ECCFn bit in the
CCAPMn SFR are set then an interrupt will
be generated. Refer to Figure 9.
16-bit Software Timer Mode
The PCA modules can be used as software
timers by setting both the ECOM and MAT
bits in the modules CCAPMn register. The
PCA timer will be compared to the module's
capture registers and when a match occurs
an interrupt will occur if the CCFn (CCON
SFR) and the ECCFn (CCAPMn SFR) bits for
the module are both set (see Figure 10).
High Speed Output Mode
In this mode the CEX output (on port 1)
associated with the PCA module will toggle
each time a match occurs between the PCA
counter and the module's capture registers.
To activate this mode the TOG, MAT, and
ECOM bits in the module's CCAPMn SFR
must be set (see Figure 11).
MODULE FUNCTIONS:
16-BIT CAPTURE
16-BIT TIMER
16-BIT HIGH SPEED OUTPUT
8-BIT PWM
WATCHDOG TIMER (MODULE 4 ONLY)
MODULE 0
MODULE 1
MODULE 2
MODULE 3
MODULE 4
P1.3/CEX0
P1.4/CEX1
P1.5/CEX2
P1.6/CEX3
P1.7/CEX4
16 BITS
PCA TIMER/COUNTER
TIME BASE FOR PCA MODULES
16 BITS
SU00032
Figure 2. Programmable Counter Array (PCA)
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
11
CF
CR
CCF4
CCF3
CCF2
CCF1
CCF0
CCON
(D8H)
CH
CL
OVERFLOW
INTERRUPT
16BIT UP COUNTER
IDLE
TO PCA
MODULES
CMOD
(D9H)
CIDL
WDTE
CPS1
CPS0
ECF
OSC/12
OSC/4
TIMER 0
OVERFLOW
EXTERNAL INPUT
(P1.2/ECI)
DECODE
00
01
10
11
SU00033
Figure 3. PCA Timer/Counter
MODULE 0
MODULE 1
MODULE 2
MODULE 3
MODULE 4
PCA TIMER/COUNTER
CF
CR
CCF4
CCF3
CCF2
CCF1
CCF0
CMOD.0 ECF
CCAPMn.0 ECCFn
TO
INTERRUPT
PRIORITY
DECODER
CCON
(D8H)
IE.6
EC
IE.7
EA
SU00034
Figure 4. PCA Interrupt System
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
12
CMOD Address = OD9H
Reset Value = 00XX X000B
CIDL
WDTE
CPS1
CPS0
ECF
Bit:
Symbol
Function
CIDL
Counter Idle control: CIDL = 0 programs the PCA Counter to continue functioning during idle Mode. CIDL = 1 programs
it to be gated off during idle.
WDTE
Watchdog Timer Enable: WDTE = 0 disables Watchdog Timer function on PCA Module 4. WDTE = 1 enables it.
Not implemented, reserved for future use.*
CPS1
PCA Count Pulse Select bit 1.
CPS0
PCA Count Pulse Select bit 0.
CPS1
CPS0
Selected PCA Input**
0
0
0
Internal clock, f
OSC
12
0
1
1
Internal clock, f
OSC
4
1
0
2
Timer 0 overflow
1
1
3
External clock at ECI/P1.2 pin (max. rate = f
OSC
8)
ECF
PCA Enable Counter Overflow interrupt: ECF = 1 enables CF bit in CCON to generate an interrupt. ECF = 0 disables
that function of CF.
NOTE:
*
User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features. In that case, the reset or inactive value of the
new bit will be 0, and its active value will be 1. The value read from a reserved bit is indeterminate.
** f
OSC
= oscillator frequency
SU00035
7
6
5
4
3
2
1
0
Figure 5. CMOD: PCA Counter Mode Register
CCON Address = OD8H
Reset Value = 00X0 0000B
CF
CR
CCF4
CCF3
CCF2
CCF1
CCF0
Bit Addressable
Bit:
Symbol
Function
CF
PCA Counter Overflow flag. Set by hardware when the counter rolls over. CF flags an interrupt if bit ECF in CMOD is
set. CF may be set by either hardware or software but can only be cleared by software.
CR
PCA Counter Run control bit. Set by software to turn the PCA counter on. Must be cleared by software to turn the PCA
counter off.
Not implemented, reserved for future use*.
CCF4
PCA Module 4 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.
CCF3
PCA Module 3 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.
CCF2
PCA Module 2 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.
CCF1
PCA Module 1 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.
CCF0
PCA Module 0 interrupt flag. Set by hardware when a match or capture occurs. Must be cleared by software.
NOTE:
*
User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features. In that case, the reset or inactive value of the
new bit will be 0, and its active value will be 1. The value read from a reserved bit is indeterminate.
SU00036
7
6
5
4
3
2
1
0
Figure 6. CCON: PCA Counter Control Register
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
13
CCAPMn Address
CCAPM0
0DAH
CCAPM1
0DBH
CCAPM2
0DCH
CCAPM3
0DDH
CCAPM4
0DEH
Reset Value = X000 0000B
ECOMn
CAPPn
CAPNn
MATn
TOGn
PWMn
ECCFn
Not Bit Addressable
Bit:
Symbol
Function
Not implemented, reserved for future use*.
ECOMn
Enable Comparator. ECOMn = 1 enables the comparator function.
CAPPn
Capture Positive, CAPPn = 1 enables positive edge capture.
CAPNn
Capture Negative, CAPNn = 1 enables negative edge capture.
MATn
Match. When MATn = 1, a match of the PCA counter with this module's compare/capture register causes the CCFn bit
in CCON to be set, flagging an interrupt.
TOGn
Toggle. When TOGn = 1, a match of the PCA counter with this module's compare/capture register causes the CEXn
pin to toggle.
PWMn
Pulse Width Modulation Mode. PWMn = 1 enables the CEXn pin to be used as a pulse width modulated output.
ECCFn
Enable CCF interrupt. Enables compare/capture flag CCFn in the CCON register to generate an interrupt.
NOTE:
*User software should not write 1s to reserved bits. These bits may be used in future 8051 family products to invoke new features. In that case, the reset or inactive value of the new
bit will be 0, and its active value will be 1. The value read from a reserved bit is indeterminate.
SU00037
7
6
5
4
3
2
1
0
Figure 7. CCAPMn: PCA Modules Compare/Capture Registers
ECOMn
CAPPn
CAPNn
MATn
TOGn
PWMn
ECCFn
MODULE FUNCTION
X
0
0
0
0
0
0
0
No operation
X
X
1
0
0
0
0
X
16-bit capture by a positive-edge trigger on CEXn
X
X
0
1
0
0
0
X
16-bit capture by a negative trigger on CEXn
X
X
1
1
0
0
0
X
16-bit capture by a transition on CEXn
X
1
0
0
1
0
0
X
16-bit Software Timer
X
1
0
0
1
1
0
X
16-bit High Speed Output
X
1
0
0
0
0
1
0
8-bit PWM
X
1
0
0
1
X
0
X
Watchdog Timer
Figure 8. PCA Module Modes (CCAPMn Register)
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
14
CF
CR
CCF4
CCF3
CCF2
CCF1
CCF0
CCON
(D8H)
ECOMn
CAPPn
CAPNn
MATn
TOGn
PWMn
ECCFn
CCAPMn, n= 0 to 4
(DAH DEH)
CH
CL
CCAPnH
CCAPnL
CEXn
CAPTURE
PCA INTERRUPT
PCA TIMER/COUNTER
0
0
0
0
(TO CCFn)
SU00749
Figure 9. PCA Capture Mode
MATCH
CF
CR
CCF4
CCF3
CCF2
CCF1
CCF0
CCON
(D8H)
ECOMn
CAPPn
CAPNn
MATn
TOGn
PWMn
ECCFn
CCAPMn, n= 0 to 4
(DAH DEH)
CH
CL
CCAPnH
CCAPnL
PCA INTERRUPT
PCA TIMER/COUNTER
0
0
0
0
16BIT COMPARATOR
(TO CCFn)
ENABLE
WRITE TO
CCAPnH
RESET
WRITE TO
CCAPnL
0
1
SU00750
Figure 10. PCA Compare Mode
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
15
CF
CR
CCF4
CCF3
CCF2
CCF1
CCF0
CCON
(D8H)
ECOMn
CAPPn
CAPNn
MATn
TOGn
PWMn
ECCFn
CCAPMn, n: 0..4
(DAH DEH)
CH
CL
CCAPnH
CCAPnL
PCA INTERRUPT
PCA TIMER/COUNTER
1
0
0
0
16BIT COMPARATOR
(TO CCFn)
WRITE TO
CCAPnH
RESET
WRITE TO
CCAPnL
0
1
ENABLE
CEXn
TOGGLE
MATCH
SU00751
Figure 11. PCA High Speed Output Mode
Pulse Width Modulator Mode
All of the PCA modules can be used as PWM
outputs. Figure 12 shows the PWM function.
The frequency of the output depends on the
source for the PCA timer. All of the modules
will have the same frequency of output
because they all share the PCA timer. The
duty cycle of each module is independently
variable using the module's capture register
CCAPLn. When the value of the PCA CL
SFR is less than the value in the module's
CCAPLn SFR the output will be low, when it
is equal to or greater than the output will be
high. When CL overflows from FF to 00,
CCAPLn is reloaded with the value in
CCAPHn. the allows updating the PWM
without glitches. The PWM and ECOM bits in
the module's CCAPMn register must be set
to enable the PWM mode.
WATCHDOG TIMER
The watchdog timer is not directly loadable
by the user. Instead, the value to be loaded
into the main timer is held in an autoload
register or is part of the mask ROM
programming. In order to cause the main
timer to be loaded with the appropriate value,
a special sequence of software action must
take place. This operation is referred to as
feeding the watchdog timer.
To feed the watchdog, two instructions must
be sequentially executed successfully. No
intervening instruction fetches are allowed,
so interrupts should be disabled before
feeding the watchdog. The instructions
should move A5H to the WFEED1 register
and then 5AH to the WFEED2 register. If
WFEED1 is correctly loaded and WFEED2 is
not correctly loaded, then an immediate
underflow will occur.
The watchdog timer subsystem has two
modes of operation. Its principal function is a
watchdog timer. In this mode it protects the
system from incorrect code execution by
causing a system reset when the watchdog
timer underflows as a result of a failure of
software to feed the timer prior to the timer
reaching its terminal count. If the user does
not employ the watchdog function, the
watchdog subsystem can be used as a timer.
In this mode, reaching the terminal count sets
a flag. In most other respects, the timer mode
possesses the characteristics of the
watchdog mode. This is done to protect the
integrity of the watchdog function.
The watchdog timer subsystem consists of a
prescaler and a main counter. The prescaler
has 8 selectable taps off the final stages and
the output of a selected tap provides the
clock to the main counter. The main counter
is the section that is loaded as a result of the
software feeding the watchdog and it is the
section that causes the system reset
(watchdog mode) or time-out flag to be set
(timer mode) if allowed to reach its terminal
count.
Programming the Watchdog Timer
Both the EPROM and ROM devices have a
set of SFRs for holding the watchdog
autoload values and the control bits. The
watchdog time-out flag is present in the
watchdog control register and operates the
same in all versions. In the EPROM device,
the watchdog parameters (autoload value
and control) are always taken from the SFRs.
In the ROM device, the watchdog parameters
can be mask programmed or taken from the
SFRs. The selection to take the watchdog
parameters from the SFRs or from the mask
programmed values is controlled by EA
(external access). When EA is high (internal
ROM access), the watchdog parameters are
taken from the mask programmed values. If
the watchdog is mask programmed to the
timer mode, then the autoload values and the
pre-scaler taps are taken from the SFRs.
When EA is low (external access), the
watchdog parameters are taken from the
SFRs. The user should be able to leave code
in his program which initializes the watchdog
SFRs even though he has migrated to the
mask ROM part. This allows no code
changes from EPROM prototyping to ROM
coded production parts.
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
16
CL < CCAPnL
ECOMn
CAPPn
CAPNn
MATn
TOGn
PWMn
ECCFn
CCAPMn, n: 0..4
(DAH DEH)
PCA TIMER/COUNTER
0
0
0
0
CL
CCAPnL
CEXn
8BIT
COMPARATOR
OVERFLOW
CCAPnH
ENABLE
0
1
CL >= CCAPnL
0
SU00752
Figure 12. PCA PWM Mode
Watchdog Detailed Operation
EPROM Device (and ROMless Operation:
EA = 0)
In the ROMless operation (ROM part, EA = 0)
and in the EPROM device, the watchdog
operates in the following manner (see
Figure 14).
Whether the watchdog is in the watchdog or
timer mode, when external RESET is applied,
the following takes place:
Watchdog mode bit set to watchdog mode.
Watchdog run control bit set to ON.
Autoload register set to 00 (min. count).
Watchdog time-out flag cleared.
Prescaler is cleared.
Prescaler tap set to the highest divide.
Autoload takes place.
The watchdog can be fed even though it is in
the timer mode.
Note that the operational concept is for the
watchdog mode of operation, when coming
out of a hardware reset, the software should
load the autoload registers, set the mode to
watchdog, and then feed the watchdog
(cause an autoload). The watchdog will now
be starting at a known point.
If the watchdog is in the watchdog mode and
running and happens to underflow at the time
the external RESET is applied, the watchdog
time-out flag will be cleared.
When the watchdog is in the watchdog mode
and the watchdog underflows, the following
action takes place (see Figure 16):
Autoload takes place.
Watchdog time-out flag is set
Mode bit unchanged.
Watchdog run bit unchanged.
Autoload register unchanged.
Prescaler tap unchanged.
All other device action same as external
reset.
Note that if the watchdog underflows, the
program counter will start from 00H as in the
case of an external reset. The watchdog
time-out flag can be examined to determine if
the watchdog has caused the reset condition.
The watchdog time-out flag bit can be cleared
by software.
When the watchdog is in the timer mode and
the timer software underflows, the following
action takes place:
Autoload takes place.
Watchdog time-out flag is set
Mode bit unchanged.
Watchdog run bit unchanged.
Autoload register unchanged.
Prescaler tap unchanged.
Mask ROM Device (EA = 1)
In the mask ROM device, the watchdog
mode bit (WDMOD) is mask programmed
and the bit in the watchdog command register
is read only and reflects the mask
programmed selection. If the mask
programmed mode bit selects the timer
mode, then the watchdog run bit (WDRUN)
operates as described under EPROM
Device. If the mask programmed bit selects
the watchdog mode, then the watchdog run
bit has no effect on the timer operation (see
Figure 15).
Watchdog Function
The watchdog consists of a programmable
prescaler and the main timer. The prescaler
derives its clock from the on-chip oscillator.
The prescaler consists of a divide by 12
followed by a 13 stage counter with taps from
stage 6 through stage 13. This is shown in
Figure 17. The tap selection is
programmable. The watchdog main counter
is a down counter clocked (decremented)
each time the programmable prescaler
underflows. The watchdog generates an
underflow signal (and is autoloaded) when
the watchdog is at count 0 and the clock to
decrement the watchdog occurs. The
watchdog is 8 bits long and the autoload
value can range from 0 to FFH. (The
autoload value of 0 is permissible since the
prescaler is cleared upon autoload).
This leads to the following user design
equations. Definitions :t
OSC
is the oscillator
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
17
period, N is the selected prescaler tap value,
W is the main counter autoload value, t
MIN
is
the minimum watchdog time-out value (when
the autoload value is 0), t
MAX
is the maximum
time-out value (when the autoload value is
FFH), t
D
is the design time-out value.
t
MIN
= t
OSC
12
64
t
MAX
= t
MIN
128
256
t
D
= t
MIN
2
PRESCALER
(W + 1)
(where prescaler = 0, 1, 2, 3, 4, 5, 6, or 7)
Note that the design procedure is anticipated
to be as follows. A t
MAX
will be chosen either
from equipment or operation considerations
and will most likely be the next convenient
value higher than t
D
. (If the watchdog were
inadvertently to start from FFH, an overflow
would be guaranteed, barring other
anomalies, to occur within t
MAX
). Then the
value for the prescaler would be chosen
from:
prescaler = log2 (t
MAX
/ (t
OSC
12
256)) - 6
This then also fixes t
MIN
. An autoload value
would then be chosen from:
W = t
D
/ t
MIN
- 1
The software must be written so that a feed
operation takes place every t
D
seconds from
the last feed operation. Some tradeoffs may
need to be made. It is not advisable to
include feed operations in minor loops or in
subroutines unless the feed operation is a
specific subroutine.
Watchdog Control Register (WDCON)
(Bit Addressable) Address C0
The following bits of this register are read
only in the ROM part when EA is high:
WDMOD, PRE0, PRE1, and PRE2. That is,
the register will reflect the mask programmed
values. In the ROM part with EA high, these
bits are taken from mask coded bits and are
not readable by the program. WDRUN is
read only in the ROM part when EA is high
and WDMOD is in the watchdog mode. When
WDMOD is in the timer mode, WDRUN
functions normally.
The parameters written into WDMOD, PRE0,
PRE1, and PRE2 by the program are not
applied directly to the watchdog timer
subsystem. The watchdog timer subsystem is
directly controlled by a second register which
stores these bits. The transfer of these bits
from the user register (WDMOD) to the
second control register takes place when the
watchdog is fed. This prevents random code
execution from directly foiling the watchdog
function. This does not affect the operation
where these bits are taken from mask coded
values.
The reset values of the WDCON and WDL
registers will be such that the timer resets to
the watchdog mode with a timeout period of
12
64
128
t
OSC
. The watchdog timer
will not generate an interrupt. Additional bits
in WDCON are used to disable reset
generation by the oscillator fail and low
voltage detect circuits. WDCON can be
written by software only by executing a valid
watchdog feed sequence.
WDCON Register Bit Definitions
WDCON.7
PRE2
Prescaler Select 2,
reset to 1
WDCON.6
PRE1
Prescaler Select 1,
reset to 1
WDCON.5
PRE0
Prescaler Select 0,
reset to 1
WDCON.4
LVRE
Low Voltage Reset
Enable, reset to 1
(enabled)
WDCON.3
OFRE
Oscillator Fail Reset
Enable, reset to 1
(enabled)
WDCON.2
WDRUN
Watchdog Run,
reset to 1 (enabled)
WDCON.1
WDTOF
Watchdog Timeout
Flag, reset =
Indeterminate
WDCON.0
WDMOD
Watchdog Mode,
reset to 1 (watchdog
mode)
Enhanced UART
The UART operates in all of the usual modes
that are described in the first section of this
book for the 80C51. In addition the UART can
perform framing error detect by looking for
missing stop bits, and automatic address
recognition. The 87C575 UART also fully
supports multiprocessor communication as
does the standard 80C51 UART.
When used for framing error detect the UART
looks for missing stop bits in the
communication. A missing bit will set the FE
bit in the SCON register. The FE bit shares
the SCON.7 bit with SM0 and the function of
SCON.7 is determined by PCON.6 (SMOD0)
(see Figure 19). If SMOD0 is set then
SCON.7 functions as FE. SCON.7 functions
as SM0 when SMOD0 is cleared. When used
as FE SCON.7 can only be cleared by
software. Refer to Figure 18.
Automatic Address Recognition
Automatic Address Recognition is a feature
which allows the UART to recognize certain
addresses in the serial bit stream by using
hardware to make the comparisons. This
feature saves a great deal of software
overhead by eliminating the need for the
software to examine every serial address
which passes by the serial port. This feature
is enabled by setting the SM2 bit in SCON. In
the 9 bit UART modes, mode 2 and mode 3,
the Receive Interrupt flag (RI) will be
automatically set when the received byte
contains either the "Given" address or the
"Broadcast" address. The 9 bit mode requires
that the 9th information bit is a 1 to indicate
that the received information is an address
and not data. Automatic address recognition
is shown in Figure 20.
The 8 bit mode is called Mode 1. In this mode
the RI flag will be set if SM2 is enabled and
the information received has a valid stop bit
following the 8 address bits and the
information is either a Given or Broadcast
address.
Mode 0 is the Shift Register mode and SM2
is ignored.
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
18
ECOMn
CAPPn
CAPNn
MATn
TOGn
PWMn
ECCFn
CCAPM4
(DEH)
CH
CL
CCAP4H
CCAP4L
RESET
PCA TIMER/COUNTER
X
0
0
0
16BIT COMPARATOR
MATCH
ENABLE
WRITE TO
CCAP4H
RESET
WRITE TO
CCAP4L
0
1
1
CMOD
(D9H)
CIDL
WDTE
CPS1
CPS0
ECF
X
SU00042
Figure 13. PCA Watchdog Timer
PRE2
PRE1
PRE0
LVRE
OFRE
WDRUN
WDTOF
WDMOD
WDCON
(C0H)
RESET
8BIT DOWN
COUNTER
PRESCALER
OSC/12
MOV WFEED1,#0A5H
MOV WFEED2,#5AH
WATCHDOG FEED SEQUENCE
SHADOW REGISTER
FOR WDCON
WDL
(C1H)
SU00240
Figure 14. Watchdog Timer in 87C575 and 80C575 / 83C575 (EA = 0)
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
19
PRE2
PRE1
PRE0
LVRE
OFRE
WDRUN
WDTOF
WDMOD
WDCON
(C0H)
8BIT DOWN
COUNTER
PRESCALER
OSC/12
MOV WFEED1,#0A5H
MOV WFEED2,#5AH
WATCHDOG FEED SEQUENCE
SHADOW REGISTER
FOR WDCON
ROMCODE
CONTENT
WD
PRE2:0
WDMOD
ADDRESS
2032H
2031H
2030H
1
SU00241
Figure 15. Watchdog Timer of 83C575 in Watchdog Mode (EA = 1, WDMOD = 1)
PRE2
PRE1
PRE0
LVRE
OFRE
WDRUN
WDTOF
WDMOD
WDCON
(C0H)
8BIT DOWN
COUNTER
PRESCALER
OSC/12
MOV WFEED1,#0A5H
MOV WFEED2,#5AH
WATCHDOG FEED SEQUENCE
SHADOW REGISTER
FOR WDCON
ROMCODE
CONTENT
WD
PRE2:0
WDMOD
ADDRESS
2032H
2031H
2030H
0
SU00242
Figure 16. Watchdog Timer of 83C575 in Timer Mode (EA = 1, WDMOD = 0)
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
20
2
2
2
2
2
2
2
PRE2
PRE1
PRE0
000
001
010
011
100
101
110
111
OSC/12
64
64
128
256
512
1024
2048
4096
8192
TO WATCHDOG
DOWN COUNTER
DECODE
SU00243
Figure 17. Watchdog Prescaler
SCON Address = 98H
Reset Value = 0000 0000B
SM0/FE
SM1
SM2
REN
TB8
RB8
Tl
Rl
Bit Addressable
(SMOD0 = 0/1)*
Symbol
Function
FE
Framing Error bit. This bit is set by the receiver when an invalid stop bit is detected. The FE bit is not cleared by valid
frames but should be cleared by software. The SMOD0 bit must be set to enable access to the FE bit.
SM0
Serial Port Mode Bit 0, (SMOD0 must = 0 to access bit SM0)
SM1
Serial Port Mode Bit 1
SM0
SM1
Mode
Description
Baud Rate**
0
0
0
shift register
f
OSC
/12
0
1
1
8-bit UART
variable
1
0
2
9-bit UART
f
OSC
/64 or f
OSC
/32
1
1
3
9-bit UART
variable
SM2
Enables the Automatic Address Recognition feature in Modes 2 or 3. If SM2 = 1 then Rl will not be set unless the
received 9th data bit (RB8) is 1, indicating an address, and the received byte is a Given or Broadcast Address.
In Mode 1, if SM2 = 1 then Rl will not be activated unless a valid stop bit was received, and the received byte is a
Given or Broadcast Address. In Mode 0, SM2 should be 0.
REN
Enables serial reception. Set by software to enable reception. Clear by software to disable reception.
TB8
The 9th data bit that will be transmitted in Modes 2 and 3. Set or clear by software as desired.
RB8
In modes 2 and 3, the 9th data bit that was received. In Mode 1, if SM2 = 0, RB8 is the stop bit that was received.
In Mode 0, RB8 is not used.
Tl
Transmit interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or at the beginning of the stop bit in the
other modes, in any serial transmission. Must be cleared by software.
Rl
Receive interrupt flag. Set by hardware at the end of the 8th bit time in Mode 0, or halfway through the stop bit time in
the other modes, in any serial reception (except see SM2). Must be cleared by software.
NOTE:
*SMOD0 is located at PCON6.
**f
OSC
= oscillator frequency
SU00043
Bit:
7
6
5
4
3
2
1
0
Figure 18. SCON: Serial Port Control Register
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
21
SMOD1
SMOD0
POF
LVF
GF0
GF1
IDL
PCON
(87H)
SM0 / FE
SM1
SM2
REN
TB8
RB8
TI
RI
SCON
(98H)
D0
D1
D2
D3
D4
D5
D6
D7
D8
STOP
BIT
DATA BYTE
ONLY IN
MODE 2, 3
START
BIT
SET FE BIT IF STOP BIT IS 0 (FRAMING ERROR)
SM0 TO UART MODE CONTROL
0 : SCON.7 = SM0
1 : SCON.7 = FE
SU00044
Figure 19. UART Framing Error Detection
Using the Automatic Address Recognition
feature allows a master to selectively
communicate with one or more slaves by
invoking the Given slave address or
addresses. All of the slaves may be
contacted by using the Broadcast address.
Two special Function Registers are used to
define the slave's address, SADDR, and the
address mask, SADEN. SADEN is used to
define which bits in the SADDR are to b used
and which bits are "don't care". The SADEN
mask can be logically ANDed with the
SADDR to create the "Given" address which
the master will use for addressing each of the
slaves. Use of the Given address allows
multiple slaves to be recognized while
excluding others. The following examples will
help to show the versatility of this scheme:
Slave 0
SADDR
=
1100 0000
SADEN
=
1111 1101
Given
=
1100 00X0
Slave 1
SADDR
=
1100 0000
SADEN
=
1111 1110
Given
=
1100 000X
In the above example SADDR is the same
and the SADEN data is used to differentiate
between the two slaves. Slave 0 requires a 0
in bit 0 and it ignores bit 1. Slave 1 requires a
0 in bit 1 and bit 0 is ignored. A unique
address for Slave 0 would be 1100 0010
since slave 1 requires a 0 in bit 1. A unique
address for slave 1 would be 1100 0001
since a 1 in bit 0 will exclude slave 0. Both
slaves can be selected at the same time by
an address which has bit 0 = 0 (for slave 0)
and bit 1 = 0 (for slave 1). Thus, both could
be addressed with 1100 0000.
In a more complex system the following could
be used to select slaves 1 and 2 while
excluding slave 0:
Slave 0
SADDR
=
1100 0000
SADEN
=
1111 1001
Given
=
1100 0XX0
Slave 1
SADDR
=
1110 0000
SADEN
=
1111 1010
Given
=
1110 0X0X
Slave 2
SADDR
=
1110 0000
SADEN
=
1111 1100
Given
=
1110 00XX
In the above example the differentiation
among the 3 slaves is in the lower 3 address
bits. Slave 0 requires that bit 0 = 0 and it can
be uniquely addressed by 1110 0110. Slave 1
requires that bit 1 = 0 and it can be uniquely
addressed by 1110 and 0101. Slave 2
requires that bit 2 = 0 and its unique address
is 1110 0011. To select Slaves 0 and 1 and
exclude Slave 2 use address 1110 0100,
since it is necessary t make bit 2 = 1 to
exclude slave 2.
The Broadcast Address for each slave is
created by taking the logical OR of SADDR
and SADEN. Zeros in this result are treated
as don't-cares. In most cases, interpreting
the don't-cares as ones, the broadcast
address will be FF hexadecimal.
Upon reset SADDR (SFR address 0A9H) and
SADEN (SFR address 0B9H) are loaded with
0s. This produces a given address of all
"don't cares" as well as a Broadcast address
of all "don't cares". this effectively disables
the Automatic Addressing mode and allows
the microcontroller to use standard 80C51
type UART drivers which do not make use of
this feature.
Analog Comparators
Four analog comparators are provided on
chip. Three comparators have a common
negative reference CMPR- and independent
positive inputs CMP1+, CMP2+, CMP3+ on
port 3. The fourth comparator has
independent positive and negative inputs
CMP0+ and CMP0- on port 1. The CMP
register contains an output and enable bit for
each comparator. The CMP register is bit
addressable and is located at SFR address
E8H. Figure 21 shows the connection of the
comparators.
Pullups at the comparator input pins will be
disabled by hardware when the comparator is
enabled. In addition, to make inputs high
impedance, the corresponding port SFR bits
must be set by software to disable the
pulldowns.
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
22
SM0
SM1
SM2
REN
TB8
RB8
TI
RI
SCON
(98H)
D0
D1
D2
D3
D4
D5
D6
D7
D8
1
1
1
0
COMPARATOR
1
1
X
RECEIVED ADDRESS D0 TO D7
PROGRAMMED ADDRESS
IN UART MODE 2 OR MODE 3 AND SM2 = 1:
INTERRUPT IF REN=1, RB8=1 AND "RECEIVED ADDRESS" = "PROGRAMMED ADDRESS"
WHEN OWN ADDRESS RECEIVED, CLEAR SM2 TO RECEIVE DATA BYTES
WHEN ALL DATA BYTES HAVE BEEN RECEIVED: SET SM2 TO WAIT FOR NEXT ADDRESS.
SU00045
Figure 20. UART Multiprocessor Communication, Automatic Address Recognition
CMP Register Bit Definitions
CMP.7
enable comparator 3,
disable pullups at P3.4, P3.7
CMP.6
enable comparator 2,
disable pullups at P3.4, P3.6
CMP.5
enable comparator 1,
disable pullups at P3.4, P3.5
CMP.4
enable comparator 0,
disable pullups at P1.0, P1.1
CMP.3
comparator 3 output (read only)
CMP.2
comparator 2 output (read only)
CMP.1
comparator 1 output (read only)
CMP.0
comparator 0 output (read only)
All comparators are disabled automatically in
power down mode, in idle mode unused
comparators should be disabled by software
to save power. A comparator can generate
an interrupt that will terminate idle mode.
The CMPE register contains bits to enable
each comparator to drive external output pins
or internal PCA capture inputs. Pullups at the
output pins are disabled by hardware when
the external comparator output is enabled.
The comparator output is wire-ORed with the
corresponding port SFR bit, so the SFR bit
must also be set by software to enable the
output.
CMPE Register Bit Definitions
CMPE.7 enables comparator 3 to drive
CEX3
CMPE.6 enables comparator 2 to drive
CEX2
CMPE.5 enables comparator 1 to drive
CEX1
CMPE.4 enables comparator 0 to drive
CEX0
CMPE.3 enables comparator 3 output on
P1.6 (open drain)
CMPE.2 enables comparator 2 output on
P1.5 (open drain)
CMPE.1 enables comparator 1 output on
P1.4 (open drain)
CMPE.0 enables comparator 0 output on
P1.3 (open drain)
When 1s are written to CMPE bits 7-4,
the comparator outputs will drive the
corresponding capture input. (This function is
not available in the idle or power-down
mode.) When 1s are written to CMPE bits 3-0
the comparator output will also drive the
corresponding port 1 pin. (This function is
available in idle mode.) If the comparator's
enabled to drive the capture input but not the
port pin, then the port pin can be used for
general purpose I/O. When a comparator
output is enabled, pullups at the output pin
are disabled and the output becomes open
drain. The comparator output can be used to
trigger a capture input in idle mode by
programming the CMPE register to drive the
pin from the comparator output to have the
pin supply the capture trigger.
There are two special function registers
associated with the comparators. They are
CMP which contains the comparator enables
and a bit that can be read by software to
determine the state of each comparator's
output, and CMPE which controls whether
the output from each comparator drives the
associated output pin or a capture input
associated with one of the PCA modules.
The CMP registers bits 03 can be read by
software to determine the state of the output
of each comparator. To do this the associated
comparator must be enabled but the output in
port 1 can be disabled. This allows easy
polling of the comparator output value without
the need to use up a port pin.
The CMPE register allows the comparator to
drive the associated PCA module capture
input, so that on compare a capture can be
generated in the PCA. Bits 03 of this
register enable the comparator output to drive
the associated port 1 output circuitry. Used
as a comparator output this circuitry is open
drain. To enable the comparator output to
drive to port 1, the corresponding port bit
must also be set to disable the pulldown. If
the comparator is not enabled to drive the
port 1 circuitry, the associated port 1 pin can
be used for other I/O. This includes when a
comparator is enabled to drive the capture
input to a PCA module.
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
23
+
+
+
+
* : WILL DISABLE PULLUPS
ON RELEVANT PINS
P3.5 / CMP1+
P3.6 / CMP2+
P3.7 / CMP3+
P3.4 / CMPR
P1.0 / CMP0+
P1.1 / CMP0
EC3DP *
EC2DP *
EC1DP *
EC0DP *
C3R0
C2R0
C1R0
C0R0
CMP
(E8H)
EC3TDC
EC2TDC
EC1TDC
EC0TDC
EC3OD *
EC2OD *
EC1OD *
EC0OD *
CMPE
(91H)
P1.3 / CMP0
P1.4 / CMP1
P1.5 / CMP2
P1.6 / CMP3
ENABLE
ENABLE
ENABLE
ENABLE
TO CEX0 INPUT OF
PCA MODULE 0
TO CEX1 INPUT OF
PCA MODULE 1
TO CEX2 INPUT OF
PCA MODULE 2
TO CEX3 INPUT OF
PCA MODULE 3
SU00244
Figure 21. Analog Comparators
Reduced EMI Mode
There are two bits in the AUXR register that
can be set to reduce the internal clock drive
and disable the ALE output. AO (AUXR.0)
when set turns off the ALE output. LO
(AUXR.1) when set reduces the drive of the
internal clock circuitry. Both bits are cleared
on Reset. With LO set the 87C575 will still
operate at 12MHz, but will have reduced EMI
in the range above 100MHz.
AUXR (8EH)
LO
AO
AO:
Turns off ALE output.
LO:
Reduces drive of internal clock
circuitry. 8XC575 spec'd to 12MHz
when LO set.
INTERNAL RESET
Internal resets generated by the power on,
low voltage, and oscillator fail detect circuits
are self timed to guarantee proper
initialization of the 8XC575. Reset will be held
approximately 24 oscillator periods after
normal conditions are detected by all enabled
detect circuits. Internal resets do not drive
RST but will cause missing pulses on ALE.
Interrupt Enable (IE) Register
EA
IE.7
enable all interrupts
EC
IE.6
enable PCA interrupt
ET2
IE.5
enable Timer 2 interrupt
ES
IE.4
enable Serial I/O interrupt
ET1
IE.3
enable Timer 1 interrupt
EX1
IE.2
enable External interrupt 1
ET0
IE.1
enable Timer 0 interrupt
EX0
IE.0
enable External interrupt 0
Interrupt Priority (IP) Register
IP.7
reserved
PPC
IP.6
PCA interrupt priority
PT2
IP.5
Timer 2 interrupt priority
PS
IP.4
Serial I/O interrupt priority
PT1
IP.3
Timer 1 interrupt priority
PX1
IP.2
External interrupt 1 priority
PT0
IP.1
Timer 0 interrupt priority
PX0
IP.0
External interrupt 0 priority
Priority Source
Flag
Vector
1
INT0
IE0
03H highest priority
2
Timer 0
TF0
0BH
3
INT1
IE1
13H
4
Timer 1
TF1
1BH
87C575
5
PCA
CF,CCFn 33H
6
Serial I/O RI,TI
23H
7
Timer 2
TF2/EXF2 2BH lowest priority
80C575/83C575/87C575
5
Serial I/O RI/TI
23H
6
Timer 2
TF2/EXF2 23H
7
PCA
CF, CCF
n
33H lowest priority
Power Control (PCON) Register
SMOD1
PCON.7 double baud rate bit
SMOD0
PCON.6 SCON.7 access control
OSF
PCON.5 oscillator fail flag
POF
PCON.4 power off flag
LVF
PCON.3 low voltage flag
GF0
PCON.2 general purpose flag
PD
PCON.1 power down mode bit
IDL
PCON.0 idle mode bit
Port 2 Pullup Disable Register
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
24
OSCILLATOR
CHARACTERISTICS
XTAL1 and XTAL2 are the input and output,
respectively, of an inverting amplifier. The
pins can be configured for use as an on-chip
oscillator, as shown in the Logic Symbol,
page 4.
To drive the device from an external clock
source, XTAL1 should be driven while XTAL2
is left unconnected. There are no
requirements on the duty cycle of the
external clock signal, because the input to
the internal clock circuitry is through a
divide-by-two flip-flop. However, minimum
and maximum high and low times specified in
the data sheet must be observed.
IDLE MODE
In idle mode, the CPU puts itself to sleep
while all of the on-chip peripherals stay
active. The instruction to invoke the idle
mode is the last instruction executed in the
normal operating mode before the idle mode
is activated. The CPU contents, the on-chip
RAM, and all of the special function registers
remain intact during this mode. The idle
mode can be terminated either by any
enabled interrupt (at which time the process
is picked up at the interrupt service routine
and continued), or by a hardware reset which
starts the processor in the same manner as a
power-on reset.
POWER-DOWN MODE
In the power-down mode, the oscillator is
stopped and the instruction to invoke
power-down is the last instruction executed.
Only the contents of the on-chip RAM are
preserved. The control bits for the reduced
power modes are in the special function
register PCON. Power-down mode can be
terminated with either a hardware reset or
external interrupt. With an external interrupt
INT0 or INT1 must be enabled and
configured as level sensitive. Holding the pin
low restarts to oscillator and bringing the pin
back high completes the exit.
If the watchdog is enabled (WDRUN = 1),
then power-down mode is disabled.
DESIGN CONSIDERATIONS
At power-on, the voltage on V
CC
must come
up with RST low for a proper start-up.
Table 2 shows the state of I/O ports during
low current operating modes.
Table 2. External Pin Status During Idle and Power-Down Modes
MODE
PROGRAM MEMORY
ALE
PSEN
PORT 0
PORT 1
PORT 2
PORT 3
Idle
Internal
1
1
Data
Data
Data
Data
Idle
External
1
1
Float
Data
Address
Data
Power-down
Internal
0
0
Data
Data
Data
Data
Power-down
External
0
0
Float
Data
Data
Data
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
25
ROM CODE SUBMISSION
When submitting ROM code for the 83C575, the following must be specified:
1. 8k byte user ROM data
2. 32 byte ROM encryption key
3. ROM security bits
4. The watchdog timer parameters.
ADDRESS
CONTENT
BIT(S)
COMMENT
0000H to 1FFFH
DATA
7:0
User ROM Data
2000H to 201FH
KEY
7:0
ROM Encryption Key
FFH = no encryption
2020H
Reserved
Security Bit 2
Security Bit 1
2
1
0
Must = 1
0 = enable, 1 = disable
0 = enable, 1 = disable
2030H
Reserved
7:0
Must = FFH
2031H
Reserved
7:0
Must = FFH
2032H
WDL
1
7:0
Watchdog reload value
(see specification)
2033H
WDCON
1
7:5
PRE2:0
2033H
WDCON
1
4
LVRE
2033H
WDCON
1
3
OFRE
2033H
WDCON
1
2
WDRUN=0, not ROM coded
2033H
WDCON
1
1
WDTOF=0, not ROM coded
2033H
WDCON
1
0
WDMOD
NOTES:
1. See Watchdog Timer Specification for definition of WDL and WDCON bits.
Security Bit 1: When programmed, this bit has two effects on masked ROM parts:
1. External MOVC is disabled, and
2. EA# is latched on Reset.
Security Bit 2: When programmed, this bit inhibits Verify User ROM.
ABSOLUTE MAXIMUM RATINGS
1, 2, 3
PARAMETER
RATING
UNIT
Operating temperature under bias
55 to +125
C
Storage temperature range
65 to +150
C
Voltage on EA/V
PP
pin to V
SS
0 to +13.0
V
Voltage on any other pin to V
SS
0.5 to +6.5
V
Maximum I
OL
per I/O pin
15
mA
Power dissipation (based on package heat transfer limitations, not
device power consumption)
1.5
W
NOTES:
1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any conditions other than those described in the AC and DC Electrical Characteristics section
of this specification is not implied.
2. This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static
charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maxima.
3. Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to V
SS
unless otherwise
noted.
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
26
DC ELECTRICAL CHARACTERISTICS
T
amb
= 0
C to +70
C and 40
C to +125
C, V
CC
= 5V
10%, V
SS
= 0V
SYMBOL
PARAMETER
TEST
LIMITS
UNIT
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
1
MAX
UNIT
V
IL
Input low voltage (Ports 0, 2, 3, except 3.2, 3.3)
0.5
0.5V
CC
0.6
V
V
IL1
Input low voltage (Ports 1, 3.2, 3.3, XTAL1, RST)
0.5
0.2V
CC
0.5
V
V
IL2
Input low voltage (EA)
0
0.2V
CC
0.45
V
V
IH
Input high voltage (Ports 0, 2, 3, except 3.2, 3.3)
0.5V
CC
+0.8
V
CC
+0.5
V
V
IH1
Input high voltage (Ports 1, 3.2, 3.3)
0.8V
CC
+0.3
V
CC
+0.5
V
V
IH2
Input high voltage (EA)
0.2V
CC
+0.9
V
CC
+0.5
V
V
IH3
Input high voltage (XTAL1, RST)
0.7V
CC
V
CC
+0.5
V
HYS
Hysteresis (Ports 0, 2, 3, except 3.2, 3.3)
200
mV
HYS1
Hysteresis (Ports 1, 3.2, 3.3)
50
mV
V
OL
Output voltage low (Ports 1, 2, 3, except 3.1)
I
OL
= 1.6mA
0.45
V
V
OL1
Output voltage low (Ports 0, ALE, PSEN
)
I
OL
= 3.2mA
0.45
V
V
OL2
Output voltage low
P3.1 with bit cleared
P3.1 with bit set
I
OL
= 10.0mA
I
OL
= 1.6mA
0.50
0.45
V
V
V
OH
Output voltage high (Ports 1, 2, 3, except P3.1)
I
OH
= 30
A
V
CC
0.7
V
V
OH1
Output voltage high (Port 0 in external bus mode, ALE, PSEN)
I
OH
= 3.2mA
V
CC
0.7
V
V
OH2
Output voltage high
P3.1 with bit cleared
P3.1 with bit set
I
OH
= 10.0mA
I
OH
= 1.6mA
V
CC
1.5
V
CC
1.5
V
V
V
IO
Offset voltage comparator inputs
35
+35
mV
V
CR
Common mode range comparator inputs
0
V
CC
V
I
IL
Logical 0 input current (Ports 1, 2, 3, except 3.1)
V
IN
= 0.45V
75
A
I
TL
Logical 1-to-0 transition current
(Ports 2, 3, except 3.1, 3.2, 3.3)
4
See Note 4
600
A
I
TL1
Logical 1-to-0 transition current (Ports 1, 3.2, 3.3)
See Note 4
450
A
I
L1
Input leakage current (Port 0, Port2 in open drain mode)
9
0.45 < V
IN
< V
CC
2
40
A
I
L2
Input leakage current (EA, P3.1)
0.45 < V
IN
< V
CC
10
+10
A
I
LC
Input leakage current comparator inputs
0 < V
IN
< V
CC
1.0
+1.0
A
I
CC
Power supply current:
7
Active mode @ 16MHz
5
Idle mode @ 16MHz
Power-down mode
See note 6
20
8
5
30
12
75
mA
mA
A
R
RST
Internal reset pull-up resistor
V
IN
= 0V
50
200
k
V
LOW
Low V
CC
detect voltage
4.0
4.45
V
C
IO
Pin capacitance
10
f = 1MHz
10
pF
NOTES: (SEE NEXT PAGE)
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
27
NOTES TO THE DC ELECTRICAL CHARACTERISTICS TABLE:
1. Typical ratings are not guaranteed. The values listed are at room temperature, 5V.
2. Capacitive loading on ports 0 and 2 may cause spurious noise to be superimposed on the V
OL
s of ALE and ports 1 and 3. The noise is due
to external bus capacitance discharging into the port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operations. In the
worst cases (capacitive loading > 100pF), the noise pulse on the ALE pin may exceed 0.8V. In such cases, it may be desirable to qualify
ALE with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input. I
OL
can exceed these conditions provided that no
single output sinks more than 5mA and no more than two outputs exceed the test conditions.
3. Capacitive loading on ports 0 and 2 may cause the V
OH
on ALE and PSEN to momentarily fall below the 0.9V
CC
specification when the
address bits are stabilizing.
4. Pins of ports 1, 2 and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its
maximum value when V
IN
is between V
IH
and V
IL
.
5. I
CC
MAX at other frequencies can be determined from Figure 29.
6. See Figures 30 through 33 for I
CC
test conditions.
7. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF.
8. Under steady state (non-transient) conditions, I
OL
must be externally limited as follows:
Maximum I
OL
per port pin:
10mA
Maximum I
OL
per 8-bit port:
26mA
Maximum total I
OL
for all outputs:
71mA
If I
OL
exceeds the test condition, V
OL
may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
test conditions.
9. Specification applies to Port 2 when P2OD bit is set.
10. 15pF MAX for the EA/V
PP
and P0.0 pins.
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
28
AC ELECTRICAL CHARACTERISTICS
T
amb
= 0
C to +70
C and 40
C to +125
C, V
CC
= 5V
10%, V
SS
= 0V
1, 2
VARIABLE CLOCK
SYMBOL
FIGURE
PARAMETER
MIN
MAX
UNIT
1/t
CLCL
22
Oscillator frequency: Speed Versions
8XC575
E
6
16
MHz
OSCF
Oscillator fail detect frequency
0.6
5.5
MHz
TR
Comparator response time
10
s
t
LHLL
22
ALE pulse width
2t
CLCL
40
ns
t
AVLL
22
Address valid to ALE low
t
CLCL
25
ns
t
LLAX
22
Address hold after ALE low
t
CLCL
25
ns
t
LLIV
22
ALE low to valid instruction in
4t
CLCL
75
ns
t
LLPL
22
ALE low to PSEN low
t
CLCL
25
ns
t
PLPH
22
PSEN pulse width
3t
CLCL
45
ns
t
PLIV
22
PSEN low to valid instruction in
3t
CLCL
70
ns
t
PXIX
22
Input instruction hold after PSEN
0
ns
t
PXIZ
22
Input instruction float after PSEN
t
CLCL
25
ns
t
AVIV
22
Address to valid instruction in
5t
CLCL
85
ns
t
PLAZ
22
PSEN low to address float
10
ns
Data Memory
t
RLRH
23, 24
RD pulse width
6t
CLCL
100
ns
t
WLWH
23, 24
WR pulse width
6t
CLCL
100
ns
t
RLDV
23, 24
RD low to valid data in
5t
CLCL
110
ns
t
RHDX
23, 24
Data hold after RD
0
ns
t
RHDZ
23, 24
Data float after RD
2t
CLCL
28
ns
t
LLDV
23, 24
ALE low to valid data in
8t
CLCL
150
ns
t
AVDV
23, 24
Address to valid data in
9t
CLCL
165
ns
t
LLWL
23, 24
ALE low to RD or WR low
3t
CLCL
50
3t
CLCL
+50
ns
t
AVWL
23, 24
Address valid to WR low or RD low
4t
CLCL
75
ns
t
QVWX
23, 24
Data valid to WR transition
t
CLCL
30
ns
t
WHQX
23, 24
Data hold after WR
t
CLCL
25
ns
t
RLAZ
23, 24
RD low to address float
0
ns
t
WHLH
23, 24
RD or WR high to ALE high
t
CLCL
25
t
CLCL
+25
ns
External Clock
t
CHCX
26
High time
12
ns
t
CLCX
26
Low time
12
ns
t
CLCH
26
Rise time
20
ns
t
CHCL
26
Fall time
20
ns
Shift Register
t
XLXL
25
Serial port clock cycle time
12t
CLCL
ns
t
QVXH
25
Output data setup to clock rising edge
10t
CLCL
133
ns
t
XHQX
25
Output data hold after clock rising edge
2t
CLCL
60
ns
t
XHDX
25
Input data hold after clock rising edge
0
ns
t
XHDV
25
Clock rising edge to input data valid
10t
CLCL
133
ns
NOTES:
1. Parameters are valid over operating temperature range unless otherwise specified.
2. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF.
3. Interfacing the 80C32/52 to devices with float times up to 45ns is permitted. This limited bus contention will not cause damage to Port 0
drivers.
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
29
EXPLANATION OF THE AC SYMBOLS
Each timing symbol has five characters. The
first character is always `t' (= time). The other
characters, depending on their positions,
indicate the name of a signal or the logical
status of that signal. The designations are:
A Address
C Clock
D Input data
H Logic level high
I Instruction (program memory contents)
L Logic level low, or ALE
P PSEN
Q Output data
R RD signal
t Time
V Valid
W WR signal
X No longer a valid logic level
Z Float
Examples: t
AVLL
= Time for address valid to
ALE low.
t
LLPL
=Time for ALE low to
PSEN low.
t
PXIZ
ALE
PSEN
PORT 0
PORT 2
A0A15
A8A15
A0A7
A0A7
t
AVLL
t
PXIX
t
LLAX
INSTR IN
t
LHLL
t
PLPH
t
LLIV
t
PLAZ
t
LLPL
t
AVIV
SU00006
t
PLIV
Figure 22. External Program Memory Read Cycle
ALE
PSEN
PORT 0
PORT 2
RD
A0A7
FROM RI OR DPL
DATA IN
A0A7 FROM PCL
INSTR IN
P2.0P2.7 OR A8A15 FROM DPF
A0A15 FROM PCH
t
WHLH
t
LLDV
t
LLWL
t
RLRH
t
LLAX
t
RLAZ
t
AVLL
t
RHDX
t
RHDZ
t
AVWL
t
AVDV
t
RLDV
SU00025
Figure 23. External Data Memory Read Cycle
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
30
t
LLAX
ALE
PSEN
PORT 0
PORT 2
WR
A0A7
FROM RI OR DPL
DATA OUT
A0A7 FROM PCL
INSTR IN
P2.0P2.7 OR A8A15 FROM DPF
A0A15 FROM PCH
t
WHLH
t
LLWL
t
WLWH
t
AVLL
t
AVWL
t
QVWX
t
WHQX
t
QVWH
SU00026
Figure 24. External Data Memory Write Cycle
0
1
2
3
4
5
6
7
8
INSTRUCTION
ALE
CLOCK
OUTPUT DATA
WRITE TO SBUF
INPUT DATA
CLEAR RI
VALID
VALID
VALID
VALID
VALID
VALID
VALID
VALID
SET TI
SET RI
t
XLXL
t
QVXH
t
XHQX
t
XHDX
t
XHDV
SU00027
1
2
3
0
4
5
6
7
Figure 25. Shift Register Mode Timing
VCC0.5
0.45V
0.7VCC
0.2VCC0.1
t
CHCL
t
CLCL
t
CLCH
t
CLCX
t
CHCX
SU00009
Figure 26. External Clock Drive
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
31
VCC0.5
0.45V
0.2VCC+0.9
0.2VCC0.1
NOTE:
AC inputs during testing are driven at V
CC
0.5 for a logic `1' and 0.45V for a logic `0'.
Timing measurements are made at V
IH
min for a logic `1' and V
IL
max for a logic `0'.
SU00010
Figure 27. AC Testing Input/Output
VLOAD
VLOAD+0.1V
VLOAD0.1V
VOH0.1V
VOL+0.1V
NOTE:
TIMING
REFERENCE
POINTS
For timing purposes, a port is no longer floating when a 100mV change from load voltage occurs,
and begins to float when a 100mV change from the loaded V
OH
/V
OL
level occurs. I
OH
/I
OL
20mA.
SU00011
Figure 28. Float Waveform
FREQUENCY (MHz)
MAX ACTIVE
TYP ACTIVE
MAX IDLE
TYP IDLE
ICC (mA)
0
4
5
10
15
16
20
30
25
20
15
10
5
0
SU00245
Figure 29. I
CC
vs. FREQ
Valid only within frequency specifications of the device under test
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
32
VCC
EA
RST
XTAL1
XTAL2
VSS
VCC
VCC
ICC
(NC)
CLOCK SIGNAL
SU00246
Figure 30. I
CC
Test Condition, Active Mode
All other pins are disconnected
VCC
EA
RST
XTAL1
XTAL2
VSS
VCC
VCC
ICC
(NC)
CLOCK SIGNAL
SU00247
Figure 31. I
CC
Test Condition, Idle Mode
All other pins are disconnected
VCC0.5
0.45V
0.7VCC
0.2VCC0.1
t
CHCL
t
CLCL
t
CLCH
t
CLCX
t
CHCX
SU00009
Figure 32. Clock Signal Waveform for I
CC
Tests in Active and Idle Modes
t
CLCH
= t
CHCL
= 5ns
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
33
VCC
EA
RST
XTAL1
XTAL2
VSS
VCC
VCC
ICC
(NC)
SU00248
Figure 33. I
CC
Test Condition, Power Down Mode
All other pins are disconnected. V
CC
= 2V to 5.5V
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
34
EPROM CHARACTERISTICS
To put the 87C575 in the EPROM
programming mode, PSEN must be held high
during power up, then driven low with reset
active. The 87C575 is programmed by using
a modified Quick-Pulse Programming
TM
algorithm. It differs from older methods in the
value used for V
PP
(programming supply
voltage) and in the width and number of the
ALE/PROG pulses.
The 87C575 contains two signature bytes
that can be read and used by an EPROM
programming system to identify the device.
The signature bytes identify the device as an
87C575 manufactured by Philips.
Table 3 shows the logic levels for reading the
signature byte, and for programming the
program memory, the encryption table, and
the security bits. The circuit configuration and
waveforms for quick-pulse programming are
shown in Figures 34 and 35. Figure 36 shows
the circuit configuration for normal program
memory verification.
Quick-Pulse Programming
The setup for microcontroller quick-pulse
programming is shown in Figure 34. Note that
the 87C575 is running with a 4 to 6MHz
oscillator. The reason the oscillator needs to
be running is that the device is executing
internal address and program data transfers.
The address of the EPROM location to be
programmed is applied to ports 1 and 2, as
shown in Figure 34. The code byte to be
programmed into that location is applied to
port 0. RST, PSEN and pins of ports 2 and 3
specified in Table 3 are held at the `Program
Code Data' levels indicated in Table 3. The
ALE/PROG is pulsed low 25 times as shown
in Figure 35.
To program the encryption table, repeat the
25 pulse programming sequence for
addresses 0 through 1FH, using the `Pgm
Encryption Table' levels. Do not forget that
after the encryption table is programmed,
verification cycles will produce only encrypted
data.
To program the security bits, repeat the 25
pulse programming sequence using the `Pgm
Security Bit' levels. After one security bit is
programmed, further programming of the
code memory and encryption table is
disabled. However, the other security bit can
still be programmed.
Note that the EA/V
PP
pin must not be allowed
to go above the maximum specified V
PP
level
for any amount of time. Even a narrow glitch
above that voltage can cause permanent
damage to the device. The V
PP
source
should be well regulated and free of glitches
and overshoot.
Program Verification
If security bit 2 has not been programmed,
the on-chip program memory can be read out
for program verification. The address of the
program memory locations to be read is
applied to ports 1 and 2 as shown in
Figure 36. The other pins are held at the
`Verify Code Data' levels indicated in Table 3.
The contents of the address location will be
emitted on port 0. External pull-ups are
required on port 0 for this operation.
If the encryption table has been programmed,
the data presented at port 0 will be the
exclusive NOR of the program byte with one
of the encryption bytes. The user will have to
know the encryption table contents in order to
correctly decode the verification data. The
encryption table itself cannot be read out.
Reading the Signature Bytes
The signature bytes are read by the same
procedure as a normal verification of
locations 030H and 031H, except that P3.6
and P3.7 need to be pulled to a logic low. The
values are:
(030H) = 15H indicates manufactured by
Philips
(B0H) =
97H indicates 87C575
Program/Verify Algorithms
Any algorithm in agreement with the
conditions listed in Table 3, and which
satisfies the timing specifications, is suitable.
Table 3.
EPROM Programming Modes
MODE
RST
PSEN
ALE/PROG
EA/V
PP
P2.7
P2.6
P3.7
P3.6
Read signature
0
0
1
1
0
0
0
0
Program code data
0
0
0*
V
PP
1
0
1
1
Verify code data
0
0
1
1
0
0
1
1
Pgm encryption table
0
0
0*
V
PP
1
0
1
0
Pgm security bit 1
0
0
0*
V
PP
1
1
1
1
Pgm security bit 2
0
0
0*
V
PP
1
1
0
0
NOTES:
1. `0' = Valid low for that pin, `1' = valid high for that pin.
2. V
PP
= 12.75V
0.25V.
3. V
CC
= 5V
10% during programming and verification.
*
ALE/PROG receives 25 programming pulses while V
PP
is held at 12.75V. Each programming pulse is low for 100
s (
10
s) and high for a
minimum of 10
s.
TM
Trademark phrase of Intel Corporation.
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
35
A0A7
0
1
1
46MHz
+5V
PGM DATA
+12.75V
25 100
s PULSES TO GROUND
0
1
0
A8A12
P1
RST
P3.6
P3.7
XTAL2
XTAL1
VSS
VCC
P0
EA/VPP
ALE/PROG
PSEN
P2.7
P2.6
P2.0P2.4
87C575
SU00249
Figure 34. Programming Configuration
ALE/PROG:
ALE/PROG:
1
0
1
0
25 PULSES
100
s+10
10
s MIN
SU00018
Figure 35. PROG Waveform
A0A7
0
1
1
46MHz
+5V
PGM DATA
1
1
0
0 ENABLE
0
A8A12
P1
RST
P3.6
P3.7
XTAL2
XTAL1
VSS
V
CC
P0
EA/VPP
ALE/PROG
PSEN
P2.7
P2.6
P2.0P2.4
87C575
SU00250
Figure 36. Program Verification
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
36
EPROM PROGRAMMING AND VERIFICATION CHARACTERISTICS
T
amb
= 21
C to +27
C, V
CC
= 5V
10%, V
SS
= 0V (See Figure 37)
SYMBOL
PARAMETER
MIN
MAX
UNIT
V
PP
Programming supply voltage
12.5
13.0
V
I
PP
Programming supply current
50
mA
1/t
CLCL
Oscillator frequency
4
6
MHz
t
AVGL
Address setup to PROG low
48t
CLCL
t
GHAX
Address hold after PROG
48t
CLCL
t
DVGL
Data setup to PROG low
48t
CLCL
t
GHDX
Data hold after PROG
48t
CLCL
t
EHSH
P2.7 (ENABLE) high to V
PP
48t
CLCL
t
SHGL
V
PP
setup to PROG low
10
s
t
GHSL
V
PP
hold after PROG
10
s
t
GLGH
PROG width
90
110
s
t
AVQV
Address to data valid
48t
CLCL
t
ELQZ
ENABLE low to data valid
48t
CLCL
t
EHQZ
Data float after ENABLE
0
48t
CLCL
t
GHGL
PROG high to PROG low
10
s
PROGRAMMING
*
VERIFICATION
*
ADDRESS
ADDRESS
DATA IN
DATA OUT
LOGIC 1
LOGIC 1
LOGIC 0
t
AVQV
t
EHQZ
t
ELQV
t
SHGL
t
GHSL
t
GLGH
t
GHGL
t
AVGL
t
GHAX
t
DVGL
t
GHDX
P1.0P1.7
P2.0P2.4
PORT 0
ALE/PROG
EA/V
PP
P2.7
ENABLE
SU00020
t
EHSH
*
FOR PROGRAMMING VERIFICATION SEE FIGURE 34.
FOR VERIFICATION CONDITIONS SEE FIGURE 36.
Figure 37. EPROM Programming and Verification
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
37
DIP40:
plastic dual in-line package; 40 leads (600 mil)
SOT129-1
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
38
PLCC44:
plastic leaded chip carrier; 44 leads
SOT187-2
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
39
QFP44:
plastic quad flat package; 44 leads (lead length 1.3 mm); body 10 x 10 x 1.75 mm
SOT307-2
Philips Semiconductors
Product specification
80C575/83C575/
87C575
80C51 8-bit microcontroller family
8K/256 OTP/ROM/ROMless, 4 comparator, failure detect circuitry, watchdog timer
1998 May 01
40
Definitions
Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support -- These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes -- Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 940883409
Telephone 800-234-7381
Copyright Philips Electronics North America Corporation 1998
All rights reserved. Printed in U.S.A.
Date of release: 05-98
Document order number:
9397 750 03854
Philips
Semiconductors
Data sheet
status
Objective
specification
Preliminary
specification
Product
specification
Product
status
Development
Qualification
Production
Definition
[1]
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
Data sheet status
[1]
Please consult the most recently issued datasheet before initiating or completing a design.