ChipFind - документация

Электронный компонент: PCB80C51BH-2P

Скачать:  PDF   ZIP
Philips
Semiconductors
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
Product specification
1996 Aug 16
INTEGRATED CIRCUITS
IC20 Data Handbook
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
2
1996 Aug 16
8530169 17187
DESCRIPTION
The Philips 80C31/80C51/87C51 is a high-performance
microcontroller fabricated with Philips high-density CMOS
technology. The CMOS 8XC51 is functionally compatible with the
NMOS 8031/8051 microcontrollers. The Philips CMOS technology
combines the high speed and density characteristics of HMOS with
the low power attributes of CMOS. Philips epitaxial substrate
minimizes latch-up sensitivity.
The 8XC51 contains a 4k
8 ROM (80C51) EPROM (87C51), a 128
8 RAM, 32 I/O lines, two 16-bit counter/timers, a five-source,
two-priority level nested interrupt structure, a serial I/O port for either
multi-processor communications, I/O expansion or full duplex UART,
and on-chip oscillator and clock circuits.
In addition, the device has two software selectable modes of power
reduction--idle mode and power-down mode. The idle mode freezes
the CPU while allowing the RAM, timers, serial port, and interrupt
system to continue functioning. The power-down mode saves the
RAM contents but freezes the oscillator, causing all other chip
functions to be inoperative.
FEATURES
8031/8051 compatible
4k
8 ROM (80C51)
4k
8 EPROM (87C51)
ROMless (80C31)
128
8 RAM
Two 16-bit counter/timers
Full duplex serial channel
Boolean processor
Memory addressing capability
64k ROM and 64k RAM
Power control modes:
Idle mode
Power-down mode
CMOS and TTL compatible
Five speed ranges at V
CC
= 5V
12MHz
16MHz
24MHz
33MHz
Five package styles
Extended temperature ranges
OTP package available
PIN CONFIGURATIONS
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
RST
RxD/P3.0
TxD/P3.1
INT0/P3.2
INT1/P3.3
T0/P3.4
T1/P3.5
P1.7
WR/P3.6
RD/P3.7
XTAL2
XTAL1
VSS
P2.0/A8
P2.1/A9
P2.2/A10
P2.3/A11
P2.4/A12
P2.5/A13
P2.6/A14
P2.7/A15
PSEN
ALE/PROG
EA/VPP
P0.7/AD7
P0.6/AD6
P0.5/AD5
P0.4/AD4
P0.3/AD3
P0.2/AD2
P0.1/AD1
P0.0/AD0
VCC
CERAMIC
AND
PLASTIC
DUAL
IN-LINE
PACKAGE
CERAMIC
AND
PLASTIC
LEAD
CHIP
CARRIER
6
1
40
7
17
39
29
18
28
PLASTIC
QUAD
FLAT
PACK
44
34
1
11
33
23
12
22
SU00001
SEE PAGE 3 FOR QFP AND LCC PIN FUNCTIONS.
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
3
CERAMIC AND PLASTIC LEADED CHIP CARRIER
PIN FUNCTIONS
LCC
6
1
40
7
17
39
29
18
28
Pin
Function
1
NC*
2
P1.0
3
P1.1
4
P1.2
5
P1.3
6
P1.4
7
P1.5
8
P1.6
9
P1.7
10
RST
11
P3.0/RxD
12
NC*
13
P3.1/TxD
14
P3.2/INT0
15
P3.3/INT1
Pin
Function
16
P3.4/T0
17
P3.5/T1
18
P3.6/WR
19
P3.7/RD
20
XTAL2
21
XTAL1
22
V
SS
23
NC*
24
P2.0/A8
25
P2.1/A9
26
P2.2/A10
27
P2.3/A11
28
P2.4/A12
29
P2.5/A13
30
P2.6/A14
Pin
Function
31
P2.7/A15
32
PSEN
33
ALE/PROG
34
NC*
35
EA/VPP
36
P0.7/AD7
37
P0.6/AD6
38
P0.5/AD5
39
P0.4/AD4
40
P0.3/AD3
41
P0.2/AD2
42
P0.1/AD1
43
P0.0/AD0
44
V
CC
SU00002
* DO NOT CONNECT
PLASTIC QUAD FLAT PACK
PIN FUNCTIONS
Pin
Function
1
P1.5
2
P1.6
3
P1.7
4
RST
5
P3.0/RxD
6
NC*
7
P3.1/TxD
8
P3.2/INT0
9
P3.3/INT1
10
P3.4/T0
11
P3.5/T1
12
P3.6/WR
13
P3.7/RD
14
XTAL2
15
XTAL1
Pin
Function
16
V
SS
17
NC*
18
P2.0/A8
19
P2.1/A9
20
P2.2/A10
21
P2.3/A11
22
P2.4/A12
23
P2.5/A13
24
P2.6/A14
25
P2.7/A15
26
PSEN
27
ALE/PROG
28
NC*
29
EA/V
PP
30
P0.7/AD7
Pin
Function
31
P0.6/AD6
32
P0.5/AD5
33
P0.4/AD4
34
P0.3/AD3
35
P0.2/AD2
36
P0.1/AD1
37
P0.0/AD0
38
V
CC
39
NC*
40
P1.0
41
P1.1
42
P1.2
43
P.13
44
P1.4
PQFP
44
34
1
11
33
23
12
22
SU00003
* DO NOT CONNECT
LOGIC SYMBOL
POR
T
0
POR
T
1
POR
T
2
POR
T
3
ADDRESS AND
DATA BUS
ADDRESS BUS
SECONDAR
Y
FUNCTIONS
RxD
TxD
INT0
INT1
T0
T1
WR
RD
RST
EA/VPP
PSEN
ALE/PROG
VSS
VCC
XTAL1
XTAL2
SU00004
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
4
ORDERING INFORMATION
PHILIPS NORTH AMERICA
EPROM
DRAWING
NUMBER
ROMless
ROM
DRAWING
NUMBER
TEMPERATURE RANGE
o
C
AND PACKAGE
1
Freq
MHz
SC87C51CCF40
0590B
0 to +70, Ceramic Dual In-line Package, UV
3.5 to 12
SC87C51CCK44
1472A
0 to +70, Ceramic Leaded Chip Carrier, UV
3.5 to 12
SC87C51CCN40
SOT129-1
SC80C31BCCN40
SC80C51BCCN40
SOT129-1
0 to +70, Plastic Dual In-line Package, OTP
3.5 to 12
SC87C51CCA44
SOT187-2
SC80C31BCCA44
SC80C51BCCA44
SOT187-2
0 to +70, Plastic Leaded Chip Carrier, OTP
3.5 to 12
SC87C51CCB44
SOT307-2
SC80C31BCCB44
SC80C51BCCB44
SOT307-2
0 to +70, Plastic Quad Flat Pack, OTP
3.5 to 12
SC87C51ACF40
0590B
40 to +85, Ceramic Dual In-line Package, UV
3.5 to 12
SC87C51ACN40
SOT129-1
SC80C31BACN40
SC80C51BACN40
SOT129-1
40 to +85, Plastic Dual In-line Package, OTP
3.5 to 12
SC87C51ACA44
SOT187-2
SC80C31BACA44
SC80C51BACA44
SOT187-2
40 to +85, Plastic Leaded Chip Carrier, OTP
3.5 to 12
SC87C51ACB44
SOT307-2
SC80C31BACB44
SC80C51BACB44
SOT307-2
40 to +85, Plastic Quad Flat Pack, OTP
3.5 to 12
SC87C51CGF40
0590B
0 to +70, Ceramic Dual In-line Package, UV
3.5 to 16
SC87C51CGK44
1472A
0 to +70, Ceramic Leaded Chip Carrier, UV
3.5 to 16
SC87C51CGN40
SOT129-1
SC80C31BCGN40
SC80C51BCGN40
SOT129-1
0 to +70, Plastic Dual In-line Package, OTP
3.5 to 16
SC87C51CGA44
SOT187-2
SC80C31BCGA44
SC80C51BCGA44
SOT187-2
0 to +70, Plastic Leaded Chip Carrier, OTP
3.5 to 16
SC87C51CGB44
SOT307-2
SC80C31BCGB44
SC80C51BCGB44
SOT307-2
0 to +70, Plastic Quad Flat Pack, OTP
3.5 to 16
SC87C51AGF40
0590B
40 to +85, Ceramic Dual In-line Package, UV
3.5 to 16
SC87C51AGN40
SOT129-1
SC80C31BAGN40
SC80C51BAGN40
SOT129-1
40 to +85, Plastic Dual In-line Package, OTP
3.5 to 16
SC87C51AGA44
SOT187-2
SC80C31BAGA44
SC80C51BAGA44
SOT187-2
40 to +85, Plastic Leaded Chip Carrier, OTP
3.5 to 16
SC87C51AGB44
SOT307-2
SC80C31BAGB44
SC80C51BAGB44
SOT307-2
40 to +85, Plastic Quad Flat Pack, OTP
3.5 to 16
SC87C51CPF40
0590B
0 to +70, Ceramic Dual In-line Package, UV
3.5 to 24
SC87C51CPK44
1472A
0 to +70, Ceramic Leaded Chip Carrier, UV
3.5 to 24
SC87C51CPN40
SOT129-1
SC80C31BCPN40
SC80C51BCPN40
SOT129-1
0 to +70, Plastic Dual In-line Package, OTP
3.5 to 24
SC87C51CPA44
SOT187-2
SC80C31BCPA44
SC80C51BCPA44
SOT187-2
0 to +70, Plastic Leaded Chip Carrier, OTP
3.5 to 24
SC87C51APF40
0590B
40 to +85, Ceramic Dual In-line Package, UV
SC87C51APN40
SOT129-1
SC80C31BAPN40
SC80C51BAPN40
SOT129-1
40 to +85, Plastic Dual In-line Package, OTP
3.5 to 24
SC87C51APA44
SOT187-2
SC80C31BAPA44
SC80C51BAPA44
SOT187-2
40 to +85, Plastic Leaded Chip Carrier, OTP
3.5 to 24
SC87C51CYF40
0590B
0 to +70, Ceramic Dual In-line Package, UV
3.5 to 33
SC87C51CYK44
1472A
0 to +70, Ceramic Leaded Chip Carrier, UV
3.5 to 33
SC87C51CYN40
SOT129-1
SC80C31BCYN40
SC80C51BCYN40
SOT129-1
0 to +70, Plastic Dual In-line Package, OTP
3.5 to 33
SC87C51CYA44
SOT187-2
SC80C31BCYA44
SC80C51BCYA44
SOT187-2
0 to +70, Plastic Leaded Chip Carrier, OTP
3.5 to 33
1. OTP = One Time Programmable EPROM. UV = UV Erasable EPROM
2. SOT311 replaced by SOT307-2.
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
5
ORDERING INFORMATION (Continued)
PHILIPS
ROMless
(ORDER NUMBER)
ROMless
(MARKING NUMBER)
ROM
DRAWING
NUMBER
TEMPERATURE RANGE
o
C
AND PACKAGE
1
Freq
MHz
PCB80C31-2 N
PCB80C31BH2-12P
PCB80C51BH-2P
SOT129-1
0 to +70, Plastic Dual In-line Package, OTP
0.5 to 12
PCB80C31-2 A
PCB80C31BH2-12WP
PCB80C51BH-2WP
SOT187-2
0 to +70, Plastic Leaded Chip Carrier, OTP
0.5 to 12
PCB80C31BH2-12H
PCB80C51BH-2H
SOT307-2
2
0 to +70, Plastic Quad Flat Pack, OTP
0.5 to 12
PCB80C31-3 N
PCB80C31BH3-16P
PCB80C51BH-3P
SOT129-1
0 to +70, Plastic Dual In-line Package, OTP
1.2 to 16
PCB80C31-3 A
PCB80C31BH3-16WP
PCB80C51BH-3WP
SOT187-2
0 to +70, Plastic Leaded Chip Carrier, OTP
1.2 to 16
PCB80C31BH3-16H
PCB80C51BH-3H
SOT307-2
2
0 to +70, Plastic Quad Flat Pack, OTP
1.2 to 16
PCF80C31-3 N
PCF80C31BH3-16P
PCF80C51BH-3P
SOT129-1
40 to +85, Plastic Dual In-line Package, OTP
1.2 to 16
PCF80C31-3 A
PCF80C31BH3-16WP
PCF80C51BH-3WP
SOT187-2
40 to +85, Plastic Leaded Chip Carrier, OTP
1.2 to 16
PCF80C31BH3-16H
PCF80C51BH-3H
SOT307-2
2
40 to +85, Plastic Quad Flat Pack, OTP
1.2 to 16
PCA80C31BH3-16P
PCA80C51BH-3P
SOT129-1
40 to +125, Plastic Dual In-line Package
1.2 to 16
PCA80C31BH3-16WP
PCA80C51BH-3WP
SOT187-2
40 to +125, Plastic Leaded Chip Carrier
1.2 to 16
PCB80C31-4 N
PCB80C31BH4-24P
PCB80C51BH-4P
SOT129-1
0 to +70, Plastic Dual In-line Package, OTP
1.2 to 24
PCB80C31-4 A
PCB80C31BH4-24WP
PCB80C51BH-4WP
SOT187-2
0 to +70, Plastic Leaded Chip Carrier, OTP
1.2 to 24
PCB80C31BH4-24H
PCB80C51BH-4H
SOT307-2
2
0 to +70, Plastic Quad Flat Pack, OTP
1.2 to 24
PCF80C31-4 N
PCF80C31BH4-24P
PCF80C51BH-4P
SOT129-1
40 to +85, Plastic Dual In-line Package, OTP
1.2 to 24
PCF80C31-4 A
PCF80C31BH4-24WP
PCF80C51BH-4WP
SOT187-2
40 to +85, Plastic Leaded Chip Carrier, OTP
1.2 to 24
PCF80C31BH4-24H
PCF80C51BH-4H
SOT307-2
2
40 to +85, Plastic Leaded Chip Carrier, OTP
1.2 to 24
PCB80C31-5 N
PCB80C31BH5-30P
PCB80C51BH-5P
SOT129-1
0 to +70, Plastic Dual In-line Package
1.2 to 33
PCB80C31-5 A
PCB80C31BH5-30WP
PCB80C51BH-5WP
SOT187-2
0 to +70, Plastic Leaded Chip Carrier
1.2 to 33
PCB80C31-5 B
PCB80C31BH5-30H
PCB80C51BH-5H
SOT307-2
2
0 to +70, Plastic Quad Flat Pack
1.2 to 33
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
6
BLOCK DIAGRAM
PSEN
EA/VPP
ALE/PROG
RST
XTAL1
XTAL2
VCC
VSS
PORT 0
DRIVERS
PORT 2
DRIVERS
RAM ADDR
REGISTER
RAM
PORT 0
LATCH
PORT 2
LATCH
ROM/EPROM
REGISTER
B
ACC
STACK
POINTER
TMP2
TMP1
ALU
TIMING
AND
CONTROL
INSTRUCTION
REGISTER
PD
OSCILLATOR
PSW
PORT 1
LATCH
PORT 3
LATCH
PORT 1
DRIVERS
PORT 3
DRIVERS
PROGRAM
ADDRESS
REGISTER
BUFFER
PC
INCRE-
MENTER
PROGRAM
COUNTER
DPTR
PCON
SCON
TMOD
TCON
TH0
TL0
TH1
TL1
SBUF
IE
IP
INTERRUPT, SERIAL
PORT AND TIMER BLOCKS
P1.0P1.7
P3.0P3.7
P0.0P0.7
P2.0P2.7
SU00005
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
7
PIN DESCRIPTION
PIN NO.
MNEMONIC
DIP
LCC
QFP
TYPE
NAME AND FUNCTION
V
SS
20
22
16
I
Ground: 0V reference.
V
CC
40
44
38
I
Power Supply: This is the power supply voltage for normal, idle, and power-down
operation.
P0.00.7
3932
4336
3730
I/O
Port 0: Port 0 is an open-drain, bidirectional I/O port. Port 0 pins that have 1s written to
them float and can be used as high-impedance inputs. Port 0 is also the multiplexed
low-order address and data bus during accesses to external program and data memory. In
this application, it uses strong internal pull-ups when emitting 1s. Port 0 also outputs the
code bytes during program verification in the 87C51. External pull-ups are required during
program verification.
P1.0P1.7
18
29
40-44,
13
I/O
Port 1: Port 1 is an 8-bit bidirectional I/O port with internal pull-ups. Port 1 pins that have 1s
written to them are pulled high by the internal pull-ups and can be used as inputs. As
inputs, port 1 pins that are externally pulled low will source current because of the internal
pull-ups. (See DC Electrical Characteristics: I
IL
). Port 1 also receives the low-order address
byte during program memory verification.
P2.0P2.7
2128
2431
1825
I/O
Port 2: Port 2 is an 8-bit bidirectional I/O port with internal pull-ups. Port 2 pins that have 1s
written to them are pulled high by the internal pull-ups and can be used as inputs. As
inputs, port 2 pins that are externally being pulled low will source current because of the
internal pull-ups. (See DC Electrical Characteristics: I
IL
). Port 2 emits the high-order
address byte during fetches from external program memory and during accesses to
external data memory that use 16-bit addresses (MOVX @DPTR). In this application, it
uses strong internal pull-ups when emitting 1s. During accesses to external data memory
that use 8-bit addresses (MOV @Ri), port 2 emits the contents of the P2 special function
register.
P3.0P3.7
1017
11,
1319
5,
713
I/O
Port 3: Port 3 is an 8-bit bidirectional I/O port with internal pull-ups. Port 3 pins that have 1s
written to them are pulled high by the internal pull-ups and can be used as inputs. As
inputs, port 3 pins that are externally being pulled low will source current because of the
pull-ups. (See DC Electrical Characteristics: I
IL
). Port 3 also serves the special features of
the 80C51 family, as listed below:
10
11
5
I
RxD (P3.0): Serial input port
11
13
7
O
TxD (P3.1): Serial output port
12
14
8
I
INT0 (P3.2): External interrupt
13
15
9
I
INT1 (P3.3): External interrupt
14
16
10
I
T0 (P3.4): Timer 0 external input
15
17
11
I
T1 (P3.5): Timer 1 external input
16
18
12
O
WR (P3.6): External data memory write strobe
17
19
13
O
RD (P3.7): External data memory read strobe
RST
9
10
4
I
Reset: A high on this pin for two machine cycles while the oscillator is running, resets the
device. An internal diffused resistor to V
SS
permits a power-on reset using only an external
capacitor to V
CC
.
ALE/PROG
30
33
27
I/O
Address Latch Enable/Program Pulse: Output pulse for latching the low byte of the
address during an access to external memory. In normal operation, ALE is emitted at a
constant rate of 1/6 the oscillator frequency, and can be used for external timing or clocking.
Note that one ALE pulse is skipped during each access to external data memory. This pin is
also the program pulse input (PROG) during EPROM programming.
PSEN
29
32
26
O
Program Store Enable: The read strobe to external program memory. When the device is
executing code from the external program memory, PSEN is activated twice each machine
cycle, except that two PSEN activations are skipped during each access to external data
memory. PSEN is not activated during fetches from internal program memory.
EA/V
PP
31
35
29
I
External Access Enable/Programming Supply Voltage: EA must be externally held low
to enable the device to fetch code from external program memory locations 0000H to
0FFFH. If EA is held high, the device executes from internal program memory unless the
program counter contains an address greater than 0FFFH. This pin also receives the
12.75V programming supply voltage (V
PP
) during EPROM programming.
XTAL1
19
21
15
I
Crystal 1: Input to the inverting oscillator amplifier and input to the internal clock generator
circuits.
XTAL2
18
20
14
O
Crystal 2: Output from the inverting oscillator amplifier.
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
8
Table 1.
80C52/80C54/80C58 Special Function Registers
SYMBOL
DESCRIPTION
DIRECT
ADDRESS
BIT ADDRESS, SYMBOL, OR ALTERNATIVE PORT FUNCTION
MSB
LSB
RESET
VALUE
ACC*
Accumulator
E0H
E7
E6
E5
E4
E3
E2
E1
E0
00H
AUXR#
Auxiliary
8EH
AO
xxxxxxx0B
AUXR1#
Auxiliary 1 (Note 2)
A2H
WUPD
0
DPS
xxxx00x0B
B*
B register
F0H
F7
F6
F5
F4
F3
F2
F1
F0
00H
DPTR:
Data Pointer (2 bytes)
DPH
Data Pointer High
83H
00H
DPL
Data Pointer Low
82H
00H
AF
AE
AD
AC
AB
AA
A9
A8
IE*
Interrupt Enable
A8H
EA
EC
ET2
ES
ET1
EX1
ET0
EX0
00H
BF
BE
BD
BC
BB
BA
B9
B8
IP*
Interrupt Priority
B8H
PT2
PS
PT1
PX1
PT0
PX0
x0000000B
B7
B6
B5
B4
B3
B2
B1
B0
IPH#
Interrupt Priority High
B7H
PT2H
PSH
PT1H
PX1H
PT0H
PX0H
x0000000B
87
86
85
84
83
82
81
80
P0*
Port 0
80H
AD7
AD6
AD5
AD4
AD3
AD2
AD1
AD0
FFH
97
96
95
94
93
92
91
90
P1*
Port 1
90H
T2EX
T2
FFH
A7
A6
A5
A4
A3
A2
A1
A0
P2*
Port 2
A0H
AD15
AD14
AD13
AD12
AD11
AD10
AD9
AD8
FFH
B7
B6
B5
B4
B3
B2
B1
B0
P3*
Port 3
B0H
RD
WR
T1
T0
INT1
INT0
TxD
RxD
FFH
PCON#
1
Power Control
87H
SMOD1
SMOD0
GF1
GF0
PD
IDL
00xx0000B
D7
D6
D5
D4
D3
D2
D1
D0
PSW*
Program Status Word
D0H
CY
AC
F0
RS1
RS0
OV
P
00H
SADDR#
Slave Address
A9H
00H
SADEN#
Slave Address Mask
B9H
00H
SBUF
Serial Data Buffer
99H
xxxxxxxxB
9F
9E
9D
9C
9B
9A
99
98
SCON*
Serial Control
98H
SM0/FE
SM1
SM2
REN
TB8
RB8
TI
RI
00H
SP
Stack Pointer
81H
07H
8F
8E
8D
8C
8B
8A
89
88
TCON*
Timer Control
88H
TF1
TR1
TF0
TR0
IE1
IT1
IE0
IT0
00H
CF
CE
CD
CC
CB
CA
C9
C8
T2MOD#
Timer 2 Mode Control
C9H
T2OE
DCEN
xxxxxx00B
TH0
Timer High 0
8CH
00H
TH1
Timer High 1
8DH
00H
TL0
Timer Low 0
8AH
00H
TL1
Timer Low 1
8BH
00H
TMOD
Timer Mode
89H
GATE
C/T
M1
M0
GATE
C/T
M1
M0
00H
*
SFRs are bit addressable.
#
SFRs are modified from or added to the 80C51 SFRs.
Reserved bits.
1. Reset value depends on reset source.
2. Available only on SC80C51.
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
9
OSCILLATOR CHARACTERISTICS
XTAL1 and XTAL2 are the input and output, respectively, of an
inverting amplifier. The pins can be configured for use as an on-chip
oscillator, as shown in the logic symbol.
To drive the device from an external clock source, XTAL1 should be
driven while XTAL2 is left unconnected. There are no requirements
on the duty cycle of the external clock signal, because the input to
the internal clock circuitry is through a divide-by-two flip-flop.
However, minimum and maximum high and low times specified in
the data sheet must be observed.
RESET
A reset is accomplished by holding the RST pin high for at least two
machine cycles (24 oscillator periods), while the oscillator is running.
To insure a good power-up reset, the RST pin must be high long
enough to allow the oscillator time to start up (normally a few
milliseconds) plus two machine cycles.
IDLE MODE
In idle mode, the CPU puts itself to sleep while all of the on-chip
peripherals stay active. The instruction to invoke the idle mode is the
last instruction executed in the normal operating mode before the
idle mode is activated. The CPU contents, the on-chip RAM, and all
of the special function registers remain intact during this mode. The
idle mode can be terminated either by any enabled interrupt (at
which time the process is picked up at the interrupt service routine
and continued), or by a hardware reset which starts the processor in
the same manner as a power-on reset.
POWER-DOWN MODE
In the power-down mode, the oscillator is stopped and the
instruction to invoke power-down is the last instruction executed.
Only the contents of the on-chip RAM are preserved. A hardware
reset is the only way to terminate the power-down mode. the control
bits for the reduced power modes are in the special function register
PCON.
Table 2 shows the state of I/O ports during low current operating
modes.
Table 2. External Pin Status During Idle and Power-Down Modes
MODE
PROGRAM MEMORY
ALE
PSEN
PORT 0
PORT 1
PORT 2
PORT 3
Idle
Internal
1
1
Data
Data
Data
Data
Idle
External
1
1
Float
Data
Address
Data
Power-down
Internal
0
0
Data
Data
Data
Data
Power-down
External
0
0
Float
Data
Data
Data
ROM CODE SUBMISSION
When submitting ROM code for the 80C51, the following must be specified:
1. 4k byte user ROM data
2. 64 byte ROM encryption key (SC80C51 only)
3. ROM security bits (SC80C51 only).
ADDRESS
CONTENT
BIT(S)
COMMENT
0000H to 0FFFH
DATA
7:0
User ROM Data
1000H to 101FH
KEY
7:0
ROM Encryption Key
1020H
SEC
0
ROM Security Bit 1
1020H
SEC
1
ROM Security Bit 2
Security Bit 1: When programmed, this bit has two effects on masked ROM parts:
1. External MOVC is disabled, and
2. EA# is latched on Reset.
Security Bit 2: When programmed, this bit inhibits Verify User ROM.
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
10
Electrical Deviations from Commercial Specifications for Extended Temperature Range (87C51)
DC and AC parameters not included here are the same as in the commercial temperature range table.
DC ELECTRICAL CHARACTERISTICS
T
amb
= 40
C to +85
C, V
CC
= 5V
10%, V
SS
= 0V (Philips North America SC87C51);
For SC87C51 (33MHz only), T
amb
= 0
C to +70
C, V
CC
= 5V
5%
T
amb
= 40
C to +85
C, V
CC
= 5V
10%, V
SS
= 0V (PCB80C31/51 and PCF80C31/51 Philips Parts Only)
TEST
LIMITS
SYMBOL
PARAMETER
CONDITIONS
MIN
MAX
UNIT
V
IL
Input low voltage, except EA (Philips North America)
0.5
0.2V
CC
0.15
V
V
IL
Input low voltage, except EA (Philips)
0.5
0.2V
CC
0.25
V
V
IL1
Input low voltage to EA
0.5
0.2V
CC
0.45
V
V
IH
Input high voltage, except XTAL1, RST
0.2V
CC
+1
V
CC
+0.5
V
V
IH1
Input high voltage to XTAL1, RST
0.7V
CC
+0.1
V
CC
+0.5
V
I
IL
Logical 0 input current, ports 1, 2, 3
V
IN
= 0.45V
75
A
I
TL
Logical 1-to-0 transition current, ports 1, 2, 3
V
IN
= 2.0V
750
A
I
CC
Power supply current:
V
CC
= 4.55.5V
CC
Active mode
1
@ 16MHz (Philips PCB80C31/51, PCF80C31/51)
25
mA
Active mode @ 12MHz (Philips North America SC87C51)
20
mA
Idle mode
2
@ 16MHz (Philips PCB80C31/51, PCF80C31/51)
6.5
mA
Idle mode @ 12MHz (Philips North America SC87C51)
5
mA
Power-down mode
3
(Philips PCB80C31/51, PCF80C31/51)
75
A
Power-down mode (Philips North America SC87C51)
50
A
NOTES:
1. The operating supply current is measured with all output pins disconnected; XTAL1 driven with t
r
= t
f
= 10ns; V
IL
= V
SS
+ 0.5V;
V
IH
= V
CC
0.5V; XTAL2 not connected; EA = RST = Port 0 = V
CC
.
2. The idle mode supply current is measured with all output pins disconnected; XTAL1 driven with t
r
= t
f
= 10ns; V
IL
= V
SS
+ 0.5V;
V
IH
= V
CC
0.5V; XTAL2 not connected; EA = Port 0 = V
CC
; RST = V
SS.
3. The power-down current is measured with all output pins disconnected, XTAL2 not connected, EA = Port 0 = V
CC
; RST = V
SS.
ABSOLUTE MAXIMUM RATINGS
1, 2, 3
PARAMETER
RATING
UNIT
Operating temperature under bias
0 to +70 or 40 to +85
C
Storage temperature range
65 to +150
C
Voltage on EA/V
PP
pin to V
SS
0 to +13.0
V
Voltage on any other pin to V
SS
0.5 to +6.5
V
Maximum I
OL
per I/O pin
15
mA
Power dissipation (based on package heat transfer limitations, not device power consumption)
1.5
W
NOTES:
1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any conditions other than those described in the AC and DC Electrical Characteristics section
of this specification is not implied.
2. This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive static
charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maxima.
3. Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to V
SS
unless otherwise
noted.
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
11
DC ELECTRICAL CHARACTERISTICS
T
amb
= 0
C to +70
C or 40
C to +85
C, V
CC
= 5V
20%, V
SS
= 0V (PCB80C31/51 and PCF80C31/51) (12, 16, and 24MHz versions)
T
amb
= 0
C to +70
C or 40
C to +85
C, V
CC
= 5V
10%, V
SS
= 0V (87C51 12, 16, and 24MHz versions) (PCB80C31/51 33MHz version);
For SC87C51 (33MHz only) T
amb
= 0
C to +70
C, V
CC
= 5V
5%
TEST
LIMITS
SYMBOL
PARAMETER
CONDITIONS
MIN
TYPICAL
1
MAX
UNIT
V
IL
Input low voltage, except EA
7
0.5
0.2V
CC
0.1
V
V
IL1
Input low voltage to EA
7
0
0.2V
CC
0.3
V
V
IH
Input high voltage, except XTAL1, RST
7
0.2V
CC
+0.9
V
CC
+0.5
V
V
IH1
Input high voltage, XTAL1, RST
7
0.7V
CC
V
CC
+0.5
V
V
OL
Output low voltage, ports 1, 2, 3
11
I
OL
= 1.6mA
2
0.45
V
V
OL1
Output low voltage, port 0, ALE, PSEN
11
I
OL
= 3.2mA
2
0.45
V
V
OH
Output high voltage, ports 1, 2, 3, ALE, PSEN
3
I
OH
= 60
A,
I
OH
= 25
A
I
OH
= 10
A
2.4
0.75V
CC
0.9V
CC
V
V
V
V
OH1
Output high voltage (port 0 in external bus mode)
I
OH
= 800
A,
I
OH
= 300
A
I
OH
= 80
A
2.4
0.75V
CC
0.9V
CC
V
V
V
I
IL
Logical 0 input current, ports 1, 2, 3
7
V
IN
= 0.45V
50
A
I
TL
Logical 1-to-0 transition current, ports 1, 2, 3
7
See note 4
650
A
I
LI
Input leakage current, port 0
V
IN
= V
IL
or V
IH
10
A
I
CC
Power supply current:
7
Active mode @ 12MHz
8
(Philips)
Active mode @ 12MHz
5
(Philips North America)
Idle mode @ 12MHz
9
(Philips)
Idle mode @ 12MHz (Philips North America)
Power-down mode
10
(Philips and
Philips North America)
See note 6
11.5
1.3
3
18
19
4.4
4
50
mA
mA
mA
mA
A
R
RST
Internal reset pull-down resistor
(Philips North America)
50
300
k
(Philips)
50
150
k
C
IO
Pin capacitance
12
10
pF
NOTES:
1. Typical ratings are not guaranteed. The values listed are at room temperature, 5V.
2. Capacitive loading on ports 0 and 2 may cause spurious noise to be superimposed on the V
OL
s of ALE and ports 1 and 3. The noise is due
to external bus capacitance discharging into the port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operations. In the
worst cases (capacitive loading > 100pF), the noise pulse on the ALE pin may exceed 0.8V. In such cases, it may be desirable to qualify
ALE with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input. I
OL
can exceed these conditions provided that no
single output sinks more than 5mA and no more than two outputs exceed the test conditions.
3. Capacitive loading on ports 0 and 2 may cause the V
OH
on ALE and PSEN to momentarily fall below the 0.9V
CC
specification when the
address bits are stabilizing.
4. Pins of ports 1, 2 and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its
maximum value when V
IN
is approximately 2V.
5. I
CCMAX
at other frequencies (for Philips North America parts) is given by: Active mode: I
CCMAX
= 1.43 X FREQ + 1.90;
Idle mode: I
CCMAX
= 0.14 X FREQ +2.31, where FREQ is the external oscillator frequency in MHz. I
CCMAX
is given in mA. See Figure 8.
6. See Figures 9 through 12 for I
CC
test conditions.
7. For Philips North America parts when T
amb
= 40
C to +85
C or Philips parts when T
amb
= 40
C to +125
C, see DC Electrical
Characteristics table on previous page.
8. The operating supply current is measured with all output pins disconnected; XTAL1 driven with t
r
= t
f
= 10ns; V
IL
= V
SS
+ 0.5V;
V
IH
= V
CC
0.5V; XTAL2 not connected; EA = RST = Port 0 = V
CC
.
9. The idle mode supply current is measured with all output pins disconnected; XTAL1 driven with t
r
= t
f
= 10ns; V
IL
= V
SS
+ 0.5V;
V
IH
= V
CC
0.5V; XTAL2 not connected; EA = Port 0 = V
CC
; RST = V
SS.
10. The power-down current is measured with all output pins disconnected, XTAL2 not connected, EA = Port 0 = V
CC
; RST = V
SS.
11. Under steady state (non-transient) conditions, I
OL
must be externally limited as follows:
Maximum I
OL
per port pin:
15mA
Maximum I
OL
per 8-bit port:
26mA
Maximum I
OL
total for all outputs:
67mA
If I
OL
exceeds the test condition, V
OL
may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
test conditions.
12. Pin capacitance for the ceramic DIP package is 15pF maximum.
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
12
DC ELECTRICAL CHARACTERISTICS FOR PHILIPS NORTH AMERICA DEVICES (SC80C31 AND SC80C51)
T
amb
= 0
C to +70
C or 40
C to +85
C, V
CC
= 5V
10%; V
SS
= 0V
SYMBOL
PARAMETER
TEST
CONDITIONS
LIMITS
UNIT
SYMBOL
PARAMETER
TEST
CONDITIONS
MIN
TYP
1
MAX
UNIT
V
IL
Input low voltage
4.5V < V
CC
< 5.5V
0.5
0.2V
CC
0.1
V
V
IH
Input high voltage (ports 0, 1, 2, 3, EA)
0.2V
CC
+0.9
V
CC
+0.5
V
V
IH1
Input high voltage, XTAL1, RST
0.7V
CC
V
CC
+0.5
V
V
OL
Output low voltage, ports 1, 2, 3
8
V
CC
= 4.5V
I
OL
= 1.6mA
2
0.4
V
V
OL1
Output low voltage, port 0, ALE, PSEN
8, 7
V
CC
= 4.5V
I
OL
= 3.2mA
2
0.4
V
V
OH
Output high voltage, ports 1, 2, 3
3
V
CC
= 4.5V
I
OH
= 30
A
V
CC
0.7
V
V
OH1
Output high voltage (port 0 in external bus mode),
ALE
9
, PSEN
3
V
CC
= 4.5V
I
OH
= 3.2mA
V
CC
0.7
V
I
IL
Logical 0 input current, ports 1, 2, 3
V
IN
= 0.4V
1
50
A
I
TL
Logical 1-to-0 transition current, ports 1, 2, 3
6
V
IN
= 2.0V
See note 4
650
A
I
LI
Input leakage current, port 0
0.45 < V
IN
< V
CC
0.3
10
A
I
CC
Power supply current (see Figure 8):
Active mode @ 16MHz
5
Idle mode @ 16MHz
5
Power-down mode
See note 5
T
amb
= 0 to +70
C
T
amb
= 40 to +85
C
11.5
1.3
3
32
5
50
75
A
A
A
A
R
RST
Internal reset pull-down resistor
40
225
k
C
IO
Pin capacitance
10
(except EA)
15
pF
NOTES:
1. Typical ratings are not guaranteed. The values listed are at room temperature, 5V.
2. Capacitive loading on ports 0 and 2 may cause spurious noise to be superimposed on the V
OL
s of ALE and ports 1 and 3. The noise is due
to external bus capacitance discharging into the port 0 and port 2 pins when these pins make 1-to-0 transitions during bus operations. In the
worst cases (capacitive loading > 100pF), the noise pulse on the ALE pin may exceed 0.8V. In such cases, it may be desirable to qualify
ALE with a Schmitt Trigger, or use an address latch with a Schmitt Trigger STROBE input. I
OL
can exceed these conditions provided that no
single output sinks more than 5mA and no more than two outputs exceed the test conditions.
3. Capacitive loading on ports 0 and 2 may cause the V
OH
on ALE and PSEN to momentarily fall below the (V
CC
0.7) specification when the
address bits are stabilizing.
4. Pins of ports 1, 2 and 3 source a transition current when they are being externally driven from 1 to 0. The transition current reaches its
maximum value when V
IN
is approximately 2V.
5. See Figures 9 through 12 for I
CC
test conditions.
Active Mode:
I
CC
= 1.5
FREQ + 8.0;
Idle Mode:
I
CC
= 0.14
FREQ +2.31; See Figure 8.
6. This value applies to T
amb
= 0
C to +70
C. For T
amb
= 40
C to +85
C, I
TL
= 750
A.
7. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF.
8. Under steady state (non-transient) conditions, I
OL
must be externally limited as follows:
Maximum I
OL
per port pin:
15mA (*NOTE: This is 85
C specification.)
Maximum I
OL
per 8-bit port:
26mA
Maximum total I
OL
for all outputs:
71mA
If I
OL
exceeds the test condition, V
OL
may exceed the related specification. Pins are not guaranteed to sink current greater than the listed
test conditions.
9. ALE is tested to V
OH1
, except when ALE is off then V
OH
is the voltage specification.
10. Pin capacitance is characterized but not tested. Pin capacitance is less than 25pF. Pin capacitance of ceramic package is less than 15pF
(except EA it is 25pF).
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
13
AC ELECTRICAL CHARACTERISTICS FOR SC87C51 1233MHz PHILIPS NORTH AMERICA DEVICES
T
amb
= 0
C to +70
C or 40
C to +85
C, V
CC
= 5V
10%, V
SS
= 0V (SC87C51 12, 16 and 24MHz versions);
For SC87C51 (33MHz only) T
amb
= = 0
C to +70
C, V
CC
= 5V
5%
VARIABLE CLOCK
3
SYMBOL
FIGURE
PARAMETER
MIN
MAX
UNIT
1/t
CLCL
Oscillator frequency: Speed Versions
SC87C51
C
G
P
Y
3.5
3.5
3.5
3.5
12
16
24
33
MHz
MHz
MHz
MHz
t
LHLL
1
ALE pulse width
2t
CLCL
40
ns
t
AVLL
1
Address valid to ALE low
t
CLCL
13
ns
t
LLAX
1
Address hold after ALE low
t
CLCL
20
ns
t
LLIV
1
ALE low to valid instruction in
4t
CLCL
65
ns
t
LLPL
1
ALE low to PSEN low
t
CLCL
13
ns
t
PLPH
1
PSEN pulse width
3t
CLCL
20
ns
t
PLIV
1
PSEN low to valid instruction in
3t
CLCL
45
ns
t
PXIX
1
Input instruction hold after PSEN
0
ns
t
PXIZ
1
Input instruction float after PSEN
t
CLCL
10
ns
t
AVIV
1
Address to valid instruction in
5t
CLCL
55
ns
t
PLAZ
1
PSEN low to address float
10
ns
Data Memory
t
RLRH
2, 3
RD pulse width
6t
CLCL
100
ns
t
WLWH
2, 3
WR pulse width
6t
CLCL
100
ns
t
RLDV
2, 3
RD low to valid data in
5t
CLCL
90
ns
t
RHDX
2, 3
Data hold after RD
0
ns
t
RHDZ
2, 3
Data float after RD
2t
CLCL
28
ns
t
LLDV
2, 3
ALE low to valid data in
8t
CLCL
150
ns
t
AVDV
2, 3
Address to valid data in
9t
CLCL
165
ns
t
LLWL
2, 3
ALE low to RD or WR low
3t
CLCL
50
3t
CLCL
+50
ns
t
AVWL
2, 3
Address valid to WR low or RD low
4t
CLCL
75
ns
t
QVWX
2, 3
Data valid to WR transition
t
CLCL
20
ns
t
WHQX
2, 3
Data hold after WR
t
CLCL
20
ns
t
RLAZ
2, 3
RD low to address float
0
ns
t
WHLH
2, 3
RD or WR high to ALE high
t
CLCL
20
t
CLCL
+25
ns
External Clock
t
CHCX
5
High time
12
ns
t
CLCX
5
Low time
12
ns
t
CLCH
5
Rise time
20
ns
t
CHCL
5
Fall time
20
ns
NOTES:
1. Parameters are valid over operating temperature range unless otherwise specified.
2. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF.
3. For all Philips North America speed versions only.
4. Interfacing the 87C51 to devices with float times up to 50ns is permitted. This limited bus contention will not cause damage to port 0 drivers.
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
14
AC ELECTRICAL CHARACTERISTICS FOR PHILIPS DEVICES
T
amb
= 0
C to +70
C, V
CC
= 5V
20%, V
SS
= 0V (PCB80C31/51, PCF80C31/51)
1, 2, 4, 5
VARIABLE CLOCK
3
SYMBOL
FIGURE
PARAMETER
MIN
MAX
UNIT
1/t
CLCL
Oscillator frequency: Speed Versions
PCB8031/51
2
PCA/PCB/PCF80C31/51
3
PCB/PCF80C31/51
4
PCB/FB80C31/51
5
0.5
1.2
1.2
1.2
12
16
24
33
MHz
MHz
MHz
MHz
t
LHLL
1
ALE pulse width
2t
CLCL
40
ns
t
AVLL
1
Address valid to ALE low
t
CLCL
25
ns
t
LLAX
1
Address hold after ALE low
t
CLCL
25
ns
t
LLIV
1
ALE low to valid instruction in
4t
CLCL
65
ns
t
LLPL
1
ALE low to PSEN low
t
CLCL
25
ns
t
PLPH
1
PSEN pulse width
3t
CLCL
45
ns
t
PLIV
1
PSEN low to valid instruction in
3t
CLCL
60
ns
t
PXIX
1
Input instruction hold after PSEN
0
ns
t
PXIZ
1
Input instruction float after PSEN
t
CLCL
25
ns
t
AVIV
1
Address to valid instruction in
5t
CLCL
80
ns
t
PLAZ
1
PSEN low to address float
10
ns
Data Memory
t
RLRH
2, 3
RD pulse width
6t
CLCL
100
ns
t
WLWH
2, 3
WR pulse width
6t
CLCL
100
ns
t
RLDV
2, 3
RD low to valid data in
5t
CLCL
90
ns
t
RHDX
2, 3
Data hold after RD
0
ns
t
RHDZ
2, 3
Data float after RD
2t
CLCL
28
ns
t
LLDV
2, 3
ALE low to valid data in
8t
CLCL
150
ns
t
AVDV
2, 3
Address to valid data in
9t
CLCL
165
ns
t
LLWL
2, 3
ALE low to RD or WR low
3t
CLCL
50
3t
CLCL
+50
ns
t
AVWL
2, 3
Address valid to WR low or RD low
4t
CLCL
75
ns
t
QVWX
2, 3
Data valid to WR transition
t
CLCL
30
ns
t
WHQX
2, 3
Data hold after WR
t
CLCL
25
ns
t
RLAZ
2, 3
RD low to address float
0
ns
t
WHLH
2, 3
RD or WR high to ALE high
t
CLCL
25
t
CLCL
+25
ns
External Clock
t
CHCX
5
High time
15
ns
t
CLCX
5
Low time
15
ns
t
CLCH
5
Rise time
20
ns
t
CHCL
5
Fall time
20
ns
NOTES:
1. Parameters are valid over operating temperature range unless otherwise specified.
2. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF.
3. For all Philips speed versions only.
4. Interfacing the 80C31/51 to devices with float times up to 30ns is permitted. This limited bus contention will not cause damage to port 0
drivers.
5. V
CC
= 5V
10% for 33MHz.
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
15
AC ELECTRICAL CHARACTERISTICS FOR PHILIPS NORTH AMERICA DEVICES (SC80C31 AND SC80C51)
T
amb
= 0
C to +70
C or 40
C to +85
C, V
CC
= 5V
10%, V
SS
= 0V
1, 2, 3
16MHz CLOCK
VARIABLE CLOCK
SYMBOL
FIGURE
PARAMETER
MIN
MAX
MIN
MAX
UNIT
1/t
CLCL
1
Oscillator frequency
Speed versions : C, G
3.5
16
MHz
t
LHLL
1
ALE pulse width
85
2t
CLCL
40
ns
t
AVLL
1
Address valid to ALE low
22
t
CLCL
40
ns
t
LLAX
1
Address hold after ALE low
32
t
CLCL
30
ns
t
LLIV
1
ALE low to valid instruction in
150
4t
CLCL
100
ns
t
LLPL
1
ALE low to PSEN low
32
t
CLCL
30
ns
t
PLPH
1
PSEN pulse width
142
3t
CLCL
45
ns
t
PLIV
1
PSEN low to valid instruction in
4
82
3t
CLCL
105
ns
t
PXIX
1
Input instruction hold after PSEN
0
0
ns
t
PXIZ
1
Input instruction float after PSEN
37
t
CLCL
25
ns
t
AVIV
1
Address to valid instruction in
4
207
5t
CLCL
105
ns
t
PLAZ
1
PSEN low to address float
10
10
ns
Data Memory
t
RLRH
2, 3
RD pulse width
275
6t
CLCL
100
ns
t
WLWH
2, 3
WR pulse width
275
6t
CLCL
100
ns
t
RLDV
2, 3
RD low to valid data in
147
5t
CLCL
165
ns
t
RHDX
2, 3
Data hold after RD
0
0
ns
t
RHDZ
2, 3
Data float after RD
65
2t
CLCL
60
ns
t
LLDV
2, 3
ALE low to valid data in
350
8t
CLCL
150
ns
t
AVDV
2, 3
Address to valid data in
397
9t
CLCL
165
ns
t
LLWL
2, 3
ALE low to RD or WR low
137
239
3t
CLCL
50
3t
CLCL
+50
ns
t
AVWL
2, 3
Address valid to WR low or RD low
122
4t
CLCL
130
ns
t
QVWX
2, 3
Data valid to WR transition
13
t
CLCL
50
ns
t
WHQX
2, 3
Data hold after WR
13
t
CLCL
50
ns
t
QVWH
3
Data valid to WR high
287
7t
CLCL
150
ns
t
RLAZ
2, 3
RD low to address float
0
0
ns
t
WHLH
2, 3
RD or WR high to ALE high
23
103
t
CLCL
40
t
CLCL
+40
ns
External Clock
t
CHCX
5
High time
20
20
t
CLCL
t
CLCX
ns
t
CLCX
5
Low time
20
20
t
CLCL
t
CHCX
ns
t
CLCH
5
Rise time
20
20
ns
t
CHCL
5
Fall time
20
20
ns
Shift Register
t
XLXL
4
Serial port clock cycle time
750
12t
CLCL
ns
t
QVXH
4
Output data setup to clock rising edge
492
10t
CLCL
133
ns
t
XHQX
4
Output data hold after clock rising edge
8
2t
CLCL
117
ns
t
XHDX
4
Input data hold after clock rising edge
0
0
ns
t
XHDV
4
Clock rising edge to input data valid
492
10t
CLCL
133
ns
NOTES:
1. Parameters are valid over operating temperature range unless otherwise specified.
2. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF.
3. Interfacing the 80C31/51 to devices with float times up to 45ns is permitted. This limited bus contention will not cause damage to Port 0
drivers.
4. See application note AN457 for external memory interfacing.
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
16
AC ELECTRICAL CHARACTERISTICS FOR PHILIPS NORTH AMERICA DEVICES (SC80C31 AND SC80C51)
T
amb
= 0
C to +70
C or 40
C to +85
C, V
CC
= 5V
10%, V
SS
= 0V
1, 2, 3
24MHz CLOCK
VARIABLE CLOCK
4
33MHz CLOCK
SYMBOL
FIGURE
PARAMETER
MIN
MAX
MIN
MAX
MIN
MAX
UNIT
1/t
CLCL
1
Oscillator frequency
Speed versions : P (24MHz)
: Y (33MHz)
3.5
24
3.5
33
3.5
33
MHz
t
LHLL
1
ALE pulse width
43
2t
CLCL
40
21
ns
t
AVLL
1
Address valid to ALE low
17
t
CLCL
25
5
ns
t
LLAX
1
Address hold after ALE low
17
t
CLCL
25
ns
t
LLIV
1
ALE low to valid instruction in
102
4t
CLCL
65
55
ns
t
LLPL
1
ALE low to PSEN low
17
t
CLCL
25
5
ns
t
PLPH
1
PSEN pulse width
80
3t
CLCL
45
45
ns
t
PLIV
1
PSEN low to valid instruction in
65
3t
CLCL
60
30
ns
t
PXIX
1
Input instruction hold after PSEN
0
0
0
ns
t
PXIZ
1
Input instruction float after PSEN
17
t
CLCL
25
5
ns
t
AVIV
1
Address to valid instruction in
128
5t
CLCL
80
70
ns
t
PLAZ
1
PSEN low to address float
10
10
10
ns
Data Memory
t
RLRH
2, 3
RD pulse width
150
6t
CLCL
100
82
ns
t
WLWH
2, 3
WR pulse width
150
6t
CLCL
100
82
ns
t
RLDV
2, 3
RD low to valid data in
118
5t
CLCL
90
60
ns
t
RHDX
2, 3
Data hold after RD
0
0
0
ns
t
RHDZ
2, 3
Data float after RD
55
2t
CLCL
28
32
ns
t
LLDV
2, 3
ALE low to valid data in
183
8t
CLCL
150
90
ns
t
AVDV
2, 3
Address to valid data in
210
9t
CLCL
165
105
ns
t
LLWL
2, 3
ALE low to RD or WR low
75
175
3t
CLCL
50
3t
CLCL
+50
40
140
ns
t
AVWL
2, 3
Address valid to WR low or RD low
92
4t
CLCL
75
45
ns
t
QVWX
2, 3
Data valid to WR transition
12
t
CLCL
30
0
ns
t
WHQX
2, 3
Data hold after WR
17
t
CLCL
25
5
ns
t
QVWH
3
Data valid to WR high
162
7t
CLCL
130
80
ns
t
RLAZ
2, 3
RD low to address float
0
0
0
ns
t
WHLH
2, 3
RD or WR high to ALE high
17
67
t
CLCL
25
t
CLCL
+25
5
55
ns
External Clock
t
CHCX
5
High time
17
17
t
CLCL
t
CLCX
ns
t
CLCX
5
Low time
17
17
t
CLCL
t
CHCX
ns
t
CLCH
5
Rise time
5
5
ns
t
CHCL
5
Fall time
5
5
ns
Shift Register
t
XLXL
4
Serial port clock cycle time
505
12t
CLCL
360
ns
t
QVXH
4
Output data setup to clock rising edge
283
10t
CLCL
133
167
ns
t
XHQX
4
Output data hold after clock rising edge
3
2t
CLCL
80
ns
t
XHDX
4
Input data hold after clock rising edge
0
0
0
ns
t
XHDV
4
Clock rising edge to input data valid
283
10t
CLCL
133
167
ns
NOTES:
1. Parameters are valid over operating temperature range unless otherwise specified.
2. Load capacitance for port 0, ALE, and PSEN = 100pF, load capacitance for all other outputs = 80pF.
3. Interfacing the SC80C31/51 to devices with float times up to 45ns is permitted. This limited bus contention will not cause damage to Port 0
drivers.
4. Variable clock is specified for oscillator frequencies greater than 16MHz to 33MHz. For frequencies equal or less than 16MHz, see 16MHz
"AC Electrial Characteristics", page 15.
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
17
EXPLANATION OF THE AC SYMBOLS
Each timing symbol has five characters. The first character is always
`t' (= time). The other characters, depending on their positions,
indicate the name of a signal or the logical status of that signal. The
designations are:
A Address
C Clock
D Input data
H Logic level high
I Instruction (program memory contents)
L Logic level low, or ALE
P PSEN
Q Output data
R RD signal
t Time
V Valid
W WR signal
X No longer a valid logic level
Z Float
Examples: t
AVLL
= Time for address valid to ALE low.
t
LLPL
= Time for ALE low to PSEN low.
t
PXIZ
ALE
PSEN
PORT 0
PORT 2
A0A15
A8A15
A0A7
A0A7
t
AVLL
t
PXIX
t
LLAX
INSTR IN
t
LHLL
t
PLPH
t
LLIV
t
PLAZ
t
LLPL
t
AVIV
SU00006
t
PLIV
Figure 1. External Program Memory Read Cycle
t
LLAX
ALE
PSEN
PORT 0
PORT 2
RD
A0A7
FROM RI OR DPL
DATA IN
A0A7 FROM PCL
INSTR IN
P2.0P2.7 OR A8A15 FROM DPH
A0A15 FROM PCH
t
WHLH
t
LLDV
t
LLWL
t
RLRH
t
RLAZ
t
AVLL
t
RHDX
t
RHDZ
t
AVWL
t
AVDV
t
RLDV
SU00007
Figure 2. External Data Memory Read Cycle
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
18
t
LLAX
ALE
PSEN
PORT 0
PORT 2
WR
A0A7
FROM RI OR DPL
DATA OUT
A0A7 FROM PCL
INSTR IN
P2.0P2.7 OR A8A15 FROM DPH
A0A15 FROM PCH
t
WHLH
t
LLWL
t
WLWH
t
AVLL
t
AVWL
t
QVWX
t
WHQX
SU00008
Figure 3. External Data Memory Write Cycle
0
1
2
3
4
5
6
7
8
INSTRUCTION
ALE
CLOCK
OUTPUT DATA
WRITE TO SBUF
INPUT DATA
CLEAR RI
VALID
VALID
VALID
VALID
VALID
VALID
VALID
VALID
SET TI
SET RI
t
XLXL
t
QVXH
t
XHQX
t
XHDX
t
XHDV
SU00027
1
2
3
0
4
5
6
7
Figure 4. Shift Register Mode Timing
VCC0.5
0.45V
0.7VCC
0.2VCC0.1
t
CHCL
t
CLCL
t
CLCH
t
CLCX
t
CHCX
SU00009
Figure 5. External Clock Drive
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
19
VCC0.5
0.45V
0.2VCC+0.9
0.2VCC0.1
NOTE:
AC inputs during testing are driven at V
CC
0.5 for a logic `1' and 0.45V for a logic `0'.
Timing measurements are made at V
IH
min for a logic `1' and V
IL
max for a logic `0'.
SU00010
Figure 6. AC Testing Input/Output
VLOAD
VLOAD+0.1V
VLOAD0.1V
VOH0.1V
VOL+0.1V
NOTE:
TIMING
REFERENCE
POINTS
For timing purposes, a port is no longer floating when a 100mV change from load voltage occurs,
and begins to float when a 100mV change from the loaded V
OH
/V
OL
level occurs. I
OH
/I
OL
20mA.
SU00011
Figure 7. Float Waveform
40
35
30
25
20
15
10
5
4MHz
8MHz
12MHz
16MHz
FREQ AT XTAL1
MAX ACTIVE MODE
(ICCMAX = 1.43 freq + 1.9)
TYP ACTIVE MODE
MAX IDLE MODE
TYP IDLE MODE
ICC mA
20MHz
24MHz
45
30MHz
33MHz
SU00012
Figure 8. I
CC
vs. FREQ
Valid only within frequency specifications of the device under test
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
20
V
CC
P0
EA
RST
XTAL1
XTAL2
V
SS
V
CC
V
CC
V
CC
I
CC
(NC)
CLOCK SIGNAL
SU00719
Figure 9. I
CC
Test Condition, Active Mode
All other pins are disconnected
V
CC
P0
EA
RST
XTAL1
XTAL2
V
SS
V
CC
V
CC
I
CC
(NC)
CLOCK SIGNAL
SU00720
Figure 10. I
CC
Test Condition, Idle Mode
All other pins are disconnected
VCC0.5
0.45V
0.7VCC
0.2VCC0.1
t
CHCL
t
CLCL
t
CLCH
t
CLCX
t
CHCX
SU00015
Figure 11. Clock Signal Waveform for I
CC
Tests in Active and Idle Modes
t
CLCH
= t
CHCL
= 5ns
V
CC
P0
EA
RST
XTAL1
XTAL2
VSS
V
CC
V
CC
I
CC
(NC)
SU00016
Figure 12. I
CC
Test Condition, Power Down Mode
All other pins are disconnected. V
CC
= 2V to 5.5V
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
21
EPROM CHARACTERISTICS
The 87C51 is programmed by using a modified Quick-Pulse
Programming
TM
algorithm. It differs from older methods in the value
used for V
PP
(programming supply voltage) and in the width and
number of the ALE/PROG pulses.
The 87C51 contains two signature bytes that can be read and used
by an EPROM programming system to identify the device. The
signature bytes identify the device as an 87C51 manufactured by
Philips Corporation.
Table 3 shows the logic levels for reading the signature bytes, and
for programming the program memory, the encryption table, and the
security bits. The circuit configuration and waveforms for quick-pulse
programming are shown in Figures 13 and 14. Figure 15 shows the
circuit configuration for normal program memory verification.
Quick-Pulse Programming
The setup for microcontroller quick-pulse programming is shown in
Figure 13. Note that the 87C51 is running with a 4 to 6MHz
oscillator. The reason the oscillator needs to be running is that the
device is executing internal address and program data transfers.
The address of the EPROM location to be programmed is applied to
ports 1 and 2, as shown in Figure 13. The code byte to be
programmed into that location is applied to port 0. RST, PSEN and
pins of ports 2 and 3 specified in Table 3 are held at the `Program
Code Data' levels indicated in Table 3. The ALE/PROG is pulsed
low 25 times as shown in Figure 14.
To program the encryption table, repeat the 25 pulse programming
sequence for addresses 0 through 1FH, using the `Pgm Encryption
Table' levels. Do not forget that after the encryption table is
programmed, verification cycles will produce only encrypted data.
To program the security bits, repeat the 25 pulse programming
sequence using the `Pgm Security Bit' levels. After one security bit is
programmed, further programming of the code memory and
encryption table is disabled. However, the other security bit can still
be programmed.
Note that the EA/V
PP
pin must not be allowed to go above the
maximum specified V
PP
level for any amount of time. Even a narrow
glitch above that voltage can cause permanent damage to the
device. The V
PP
source should be well regulated and free of glitches
and overshoot.
Program Verification
If security bit 2 has not been programmed, the on-chip program
memory can be read out for program verification. The address of the
program memory locations to be read is applied to ports 1 and 2 as
shown in Figure 15. The other pins are held at the `Verify Code Data'
levels indicated in Table 3. The contents of the address location will
be emitted on port 0. External pull-ups are required on port 0 for this
operation.
If the encryption table has been programmed, the data presented at
port 0 will be the exclusive NOR of the program byte with one of the
encryption bytes. The user will have to know the encryption table
contents in order to correctly decode the verification data. The
encryption table itself cannot be read out.
Reading the Signature Bytes
The signature bytes are read by the same procedure as a normal
verification of locations 030H and 031H, except that P3.6 and P3.7
need to be pulled to a logic low. The values are:
(030H) = 15H indicates manufactured by Philips
(031H) = 92H indicates 87C51
Program/Verify Algorithms
Any algorithm in agreement with the conditions listed in Table 3, and
which satisfies the timing specifications, is suitable.
Erasure Characteristics
Erasure of the EPROM begins to occur when the chip is exposed to
light with wavelengths shorter than approximately 4,000 angstroms.
Since sunlight and fluorescent lighting have wavelengths in this
range, exposure to these light sources over an extended time (about
1 week in sunlight, or 3 years in room level fluorescent lighting)
could cause inadvertent erasure. For this and secondary effects,
it is recommended that an opaque label be placed over the
window.
For elevated temperature or environments where solvents
are being used, apply Kapton tape Fluorglas part number 23455, or
equivalent.
The recommended erasure procedure is exposure to ultraviolet light
(at 2537 angstroms) to an integrated dose of at least 15W-sec/cm
2
.
Exposing the EPROM to an ultraviolet lamp of 12,000
W/cm
2
rating
for 20 to 39 minutes, at a distance of about 1 inch, should be
sufficient.
Erasure leaves the array in an all 1s state.
Table 3. EPROM Programming Modes
MODE
RST
PSEN
ALE/PROG
EA/V
PP
P2.7
P2.6
P3.7
P3.6
Read signature
1
0
1
1
0
0
0
0
Program code data
1
0
0*
V
PP
1
0
1
1
Verify code data
1
0
1
1
0
0
1
1
Pgm encryption table
1
0
0*
V
PP
1
0
1
0
Pgm security bit 1
1
0
0*
V
PP
1
1
1
1
Pgm security bit 2
1
0
0*
V
PP
1
1
0
0
NOTES:
1. `0' = Valid low for that pin, `1' = valid high for that pin.
2. V
PP
= 12.75V +0.25V.
3. V
CC
= 5V
10% during programming and verification.
4. *ALE/PROG receives 25 programming pulses while V
PP
is held at 12.75V. Each programming pulse is low for 100
s (
10
s) and high for a
minimum of 10
s.
TM
Trademark phrase of Intel Corporation.
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
22
A0A7
1
1
1
46MHz
+5V
PGM DATA
+12.75V
25 100
s PULSES TO GROUND
0
1
0
A8A11
P1
RST
P3.6
P3.7
XTAL2
XTAL1
VSS
VCC
P0
EA/VPP
ALE/PROG
PSEN
P2.7
P2.6
P2.0P2.3
87C51
SU00017
Figure 13. Programming Configuration
ALE/PROG:
ALE/PROG:
1
0
1
0
25 PULSES
100
s+10
10
s MIN
SU00018
Figure 14. PROG Waveform
A0A7
1
1
1
46MHz
+5V
PGM DATA
1
1
0
0 ENABLE
0
A8A11
P1
RST
P3.6
P3.7
XTAL2
XTAL1
VSS
VCC
P0
EA/VPP
ALE/PROG
PSEN
P2.7
P2.6
P2.0P2.3
87C51
SU00019
Figure 15. Program Verification
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
23
EPROM PROGRAMMING AND VERIFICATION CHARACTERISTICS
T
amb
= 21
C to +27
C, V
CC
= 5V
10%, V
SS
= 0V (See Figure 16)
SYMBOL
PARAMETER
MIN
MAX
UNIT
V
PP
Programming supply voltage
12.5
13.0
V
I
PP
Programming supply current
50
mA
1/t
CLCL
Oscillator frequency
4
6
MHz
t
AVGL
Address setup to PROG low
48t
CLCL
t
GHAX
Address hold after PROG
48t
CLCL
t
DVGL
Data setup to PROG low
48t
CLCL
t
GHDX
Data hold after PROG
48t
CLCL
t
EHSH
P2.7 (ENABLE) high to V
PP
48t
CLCL
t
SHGL
V
PP
setup to PROG low
10
s
t
GHSL
V
PP
hold after PROG
10
s
t
GLGH
PROG width
90
110
s
t
AVQV
Address to data valid
48t
CLCL
t
ELQZ
ENABLE low to data valid
48t
CLCL
t
EHQZ
Data float after ENABLE
0
48t
CLCL
t
GHGL
PROG high to PROG low
10
s
PROGRAMMING
*
VERIFICATION
*
ADDRESS
ADDRESS
DATA IN
DATA OUT
LOGIC 1
LOGIC 1
LOGIC 0
t
AVQV
t
EHQZ
t
ELQV
t
SHGL
t
GHSL
t
GLGH
t
GHGL
t
AVGL
t
GHAX
t
DVGL
t
GHDX
P1.0P1.7
P2.0P2.4
PORT 0
ALE/PROG
EA/V
PP
P2.7
ENABLE
SU00020
t
EHSH
NOTE:
*
FOR PROGRAMMING VERIFICATION SEE FIGURE 13.
FOR VERIFICATION CONDITIONS SEE FIGURE 15.
Figure 16. EPROM Programming and Verification
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
24
0590B
40-PIN (600 mils wide) CERAMIC DUAL IN-LINE (F) PACKAGE (WITH WINDOW (FA) PACKAGE)
NOTES:
1.
Controlling dimension: Inches. Millimeters are
2.
Dimension and tolerancing per
ANSI
Y14. 5M-1982.
3.
"T", "D", and "E" are reference datums on the body
4.
These dimensions measured with the leads
5.
Pin numbers start with Pin #1 and continue
6.
Denotes window location for EPROM products.
and include allowance for glass overrun and meniscus
on the seal line, and lid to base mismatch.
constrained to be perpendicular to plane
T
.
counterclockwise to Pin #40 when viewed
shown in parentheses.
from the top.
D
PIN # 1
E
0.225 (5.72) MAX.
0.010 (0.254)
T
E
D
0.023 (0.58)
0.015 (0.38)
0.165 (4.19)
0.125 (3.18)
0.070 (1.78)
0.050 (1.27)
T
SEA
TING
PLANE
0.620 (15.75)
0.590 (14.99)
(NOTE 4)
0.598 (15.19)
0.571 (14.50)
BSC
0.600 (15.24)
0.695 (17.65)
0.600 (15.24)
(NOTE 4)
0.015 (0.38)
0.010 (0.25)
0.175 (4.45)
0.145 (3.68)
0.055 (1.40)
0.020 (0.51)
0.100 (2.54) BSC
2.087 (53.01)
2.038 (51.77)
0.098 (2.49)
0.040 (1.02)
0.098 (2.49)
0.040 (1.02)
SEE NOTE 6
8530590B 06688
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
25
1472A
44-PIN CERQUAD J-BEND (K) PACKAGE
NOTES:
1.
All dimensions and tolerances to conform
2.
UV window is optional.
3.
Dimensions do not include glass protrusion.
Glass protrusion to be 0.005 inches maximum
4.
Controlling dimension millimeters.
5.
All dimensions and tolerances include
lead trim of
fset and lead plating finish.
6.
Backside solder relief is optional and
dimensions are for reference only
.
1.02 (0.040) X 45
16.89 (0.665)
16.00 (0.630)
17.65 (0.695)
17.40 (0.685)
CHAMFER
45
16.89 (0.665)
16.00 (0.630)
17.65 (0.695)
17.40 (0.685)
on each side.
to
ANSI
Y14.51982.
2
3
3 X 0.63 (0.025) R MIN.
3.05 (0.120)
2.29 (0.090)
4.83 (0.190)
3.94 (0.155)
SEA
TING
PLANE
0.38 (0.015)
0.51 (0.02) X 45
6
6
17.65 (0.656)
17.40 (0.685)
1.27 (0.050)
12.7 (0.500)
8.13 (0.320)
7.37 (0.290)
40X
4.83 (0.190)
3.94 (0.155)
SEA
TING
PLANE
0.15 (0.006) MIN.
0.25 (0.010) R MIN.
0.508 (0.020) R MIN.
0.25 (0.010)
0.15 (0.006)
90
+ 5
10
0.076 (0.003) MIN.
DET
AIL
B
mm/(inch)
SEE DET
AIL
B
SEE DET
AIL

A
DET
AIL

A
TYP
.
ALL
SIDES
mm/(inch)
1.52 (0.060) REF
.
0.482 (0.019 + 0.002)
SEA
TING
PLANE
1.02 + 0.25 (0.040 + 0.010)
BASE PLANE
45
TYP
.
4 PLACES
0.73 + 0.08 (0.029 + 0.003)
1.27 (0.050)
TYP
.
NOMINAL
8.13 (0.320)
7.37 (0.290)
3
853-1472A 05854
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
26
DIP40:
plastic dual in-line package; 40 leads (600 mil)
SOT129-1
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
27
PLCC44:
plastic leaded chip carrier; 44 leads
SOT187-2
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
28
QFP44:
plastic quad flat package; 44 leads (lead length 1.3 mm); body 10 x 10 x 1.75 mm
SOT307-2
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
1996 Aug 16
29
NOTES
Philips Semiconductors
Product specification
80C31/80C51/87C51
CMOS single-chip 8-bit microcontrollers
Philips Semiconductors and Philips Electronics North America Corporation reserve the right to make changes, without notice, in the products,
including circuits, standard cells, and/or software, described or contained herein in order to improve design and/or performance. Philips
Semiconductors assumes no responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright,
or mask work right to these products, and makes no representations or warranties that these products are free from patent, copyright, or mask work
right infringement, unless otherwise specified. Applications that are described herein for any of these products are for illustrative purposes only.
Philips Semiconductors makes no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
LIFE SUPPORT APPLICATIONS
Philips Semiconductors and Philips Electronics North America Corporation Products are not designed for use in life support appliances, devices,
or systems where malfunction of a Philips Semiconductors and Philips Electronics North America Corporation Product can reasonably be expected
to result in a personal injury. Philips Semiconductors and Philips Electronics North America Corporation customers using or selling Philips
Semiconductors and Philips Electronics North America Corporation Products for use in such applications do so at their own risk and agree to fully
indemnify Philips Semiconductors and Philips Electronics North America Corporation for any damages resulting from such improper use or sale.
This data sheet contains preliminary data, and supplementary data will be published at a later date. Philips
Semiconductors reserves the right to make changes at any time without notice in order to improve design
and supply the best possible product.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 940883409
Telephone 800-234-7381
DEFINITIONS
Data Sheet Identification
Product Status
Definition
Objective Specification
Preliminary Specification
Product Specification
Formative or in Design
Preproduction Product
Full Production
This data sheet contains the design target or goal specifications for product development. Specifications
may change in any manner without notice.
This data sheet contains Final Specifications. Philips Semiconductors reserves the right to make changes
at any time without notice, in order to improve design and supply the best possible product.
Philips Semiconductors and Philips Electronics North America Corporation register
eligible circuits under the Semiconductor Chip Protection Act.
Copyright Philips Electronics North America Corporation 1996
All rights reserved. Printed in U.S.A.