Philips
Semiconductors
UCB1100
Advanced modem/audio analog front-end
Preliminary specification
Supersedes data of 1996 Apr 09
1998 May 08
INTEGRATED CIRCUITS
Version 1.2
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
Version 1.2
2
1998 May 08
GENERAL DESCRIPTION
The UCB1100 is a single chip, integrated mixed signal audio and
telecom codec. The single channel audio codec is designed for
direct connection of a microphone and speaker. The built-in telecom
codec can directly be connected to a DAA and supports high speed
modem protocols. The incorporated 10 bit analogue to digital
converter and the touch screen interface provides complete control
and readout of a connected 4 wire resistive touch screen. The 10
additional general purpose I/O pins provides programmable inputs
and/or outputs to the system.
The UCB1100 has a serial interface bus (SIB) intended to
communicate to the system controller. Both the codec input and
output data and the control register data is multiplexed on this SIB
interface.
APPLICATIONS
Personal Intelligent Communicators
Personal Digital Assistants (PDA)
Screen phones
Smart Phone and smart Fax
Intelligent Communicators
KEY FEATURES
48-pin LQFP (SOT313-2) small body SMD package and low
external component count result in minimal PCB space
requirement.
A 12-bit sigma delta audio codec with programmable sample rate,
input and output voltage levels, capable of connecting directly to
speaker and microphone, including digitally controlled mute,
loopback and clip detection functions
A 14-bit sigma delta telecom codec with programmable sample
rate, including digitally controlled input voltage level, mute,
loopback and clip detection functions. The telecom codec is
intended for direct connection to a DAA (digital access
arrangement) and includes a built-in sidetone suppression circuit.
A complete 4 wire resistive touch screen interface circuit
supporting position, pressure and plate resistance measurements.
A 10-bit successive approximation ADC with internal track and
hold circuit and analogue multiplier for touch screen readout and
monitoring of four external high voltage (7.5V) analogue voltages.
A high speed, 4 wire serial interface data bus (SIB) for
communication to system controller.
A 3.3V supply voltage and built in power saving modes make the
UCB1100 optimal for portable and battery powered applications.
TABLE OF CONTENTS
GENERAL DESCRIPTION
2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
APPLICATIONS
2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
KEY FEATURES
2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
TABLE OF CONTENTS
2
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
1.0
FUNCTIONAL BLOCK DIAGRAM
3
. . . . . . . . . . . . . . . . . . . . .
2.0
ORDERING INFORMATION
4
. . . . . . . . . . . . . . . . . . . . . . . . . .
3.0
ABSOLUTE MAXIMUM RATINGS
4
. . . . . . . . . . . . . . . . . . . . .
4.0
DC ELECTRICAL CHARACTERISTICS
5
. . . . . . . . . . . . . . . .
5.0
PINOUT
6
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
5.1
PINLIST
7
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.0
FUNCTIONAL DESCRIPTION
8
. . . . . . . . . . . . . . . . . . . . . . . .
6.1
AUDIO CODEC
8
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.1.1 AUDIO INPUT SPECIFICATIONS
10
. . . . . . . .
6.1.2 AUDIO OUTPUT SPECIFICATIONS
11
. . . . . . .
6.2
TELECOM CODEC
12
. . . . . . . . . . . . . . . . . . . . . . . . . . .
6.2.1 TELECOM INPUT SPECIFICATIONS
14
. . . . .
6.2.2 TELECOM OUTPUT SPECIFICATIONS
15
. . .
6.3
TOUCH SCREEN MEASUREMENT MODES
16
. . . .
6.3.1 POSITION MEASUREMENT
16
. . . . . . . . . . . . .
6.3.2 PRESSURE MEASUREMENT
16
. . . . . . . . . . .
6.3.3 PLATE RESISTANCE MEASUREMENT
16
. . .
6.4
TOUCH SCREEN INTERFACE
17
. . . . . . . . . . . . . . . . .
6.4.1 TOUCH SCREEN SPECIFICATIONS
18
. . . . .
6.5
10 BIT ADC.
19
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
6.5.1 SPECIFICATION OVERVIEW
21
. . . . . . . . . . . .
6.6
ON CHIP REFERENCE CIRCUIT
21
. . . . . . . . . . . . . .
6.6.1 SPECIFICATION OVERVIEW
21
. . . . . . . . . . . .
6.7
SERIAL INTERFACE BUS
22
. . . . . . . . . . . . . . . . . . . . .
6.7.1 SIB DATA FORMAT
23
. . . . . . . . . . . . . . . . . . . . .
6.7.2 CODEC DATA TRANSFER
24
. . . . . . . . . . . . . .
6.7.3 CONTROL REGISTER DATA TRANSFER
26
.
6.7.4 AC ELECTRICAL CHARACTERISTICS
27
. . .
6.8
GENERAL PURPOSE I/Os
27
. . . . . . . . . . . . . . . . . . . .
6.9
INTERRUPT GENERATION
27
. . . . . . . . . . . . . . . . . . .
6.10
RESET CIRCUITRY
28
. . . . . . . . . . . . . . . . . . . . . . . . . .
7.0
MISCELLANEOUS
29
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
7.1
POWER ROUTING STRATEGY
29
. . . . . . . . . . . . . . . .
8.0
CONTROL REGISTER OVERVIEW
30
. . . . . . . . . . . . . . . . . .
9.0
PACKAGE OUTLINES
34
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
9.1
PACKAGE OUTLINE LQFP48
34
. . . . . . . . . . . . . . . . . .
10.0
DEFINITIONS
36
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
3
1.0
FUNCTIONAL BLOCK DIAGRAM
vdda2
vssa2
tinp
tinn
tsmx
tspy
tsmy
vssa3
ad0
ad1
ad2
ad3
switched
voltage
dividers
touch screen
switch matrix
vrefbyp
toutp
toutn
mux
9 to 1
touch screen
bias voltage
mute
echo on
loopback
mux
attenuation
1 bit
ADC
ef
fect
4 bit DAC
ef
fect
4
64fs
digital
noise
shaper
telecom output enable
4
64fs
digital
decimation
filter
14
fs
14
fs
supply pin
analog pin
digital pin
sample
frequency
divider
divaud[0:6]
fsa
64fsa
sample
frequency
divider
divtel0:6]
fst
64fst
track & hold
reference
voltage
10 bit
ADC
TELECOM CODEC
10
to external register 1
1
side tone suppression
ADC start
stop logic
adcsync
adc_sync_ena
power
control
eanble data
for all
analog blocks
adc
start
sync
enable
io0
io1
io2
io3
io4
io5
io6
io7
io8
io9
Programmable IO pin block
IOmode[0:9]
IOwdat[0:9]
IOrdat[0:9]
interrupt data
from other blocks
rising_edge_ena[0:15]
clear_interrupt[0:15]
falling_edge_ena[0:15]
Interrupt
controller
irqout
reset
stretcher
internal
reset
nreset
serial bus
decoder
sibdin
serial bus
controller
sibclk
sibsync
serial bus
encoder
sibdout
external
reference
external
filter
control data registers
to all other analog and digital blocks
test
spkrp
spkrn
mute
4 bit DAC
64fsa
4
64fs
digital
volume
control
audio_output_enable
12
fs
telecom input enable
digital
noise
shaper
attn[4,5]
attn[0,3]
loopback
mux
gain[0,2]
1 bit
ADC
64fsa
1
64fs
digital
decimation
filter
12
fs
AUDIO CODEC
audio_input_enable
gain[3,4]
vssa1
micgnd
micp
2xVddd
2xVssd
Vdda1
Vssa1
SN00126
Figure 1.
Block Diagram of the UCB1100
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
4
2.0
ORDERING INFORMATION
DESCRIPTION
ORDERING
CODE
PACKAGE
DRAWING
Plastic low profile
quad flat package;
48 leads
UCB1100LP/X3
SOT313-2
3.0
ABSOLUTE MAXIMUM RATINGS
SYMBOL
PARAMETER
MIN
MAX
UNIT
V
DDMAX
Supply voltage
0.5
5.0
V
V
IMAX
DC input voltage, except AD03 inputs
0.5
V
DD
+0.5
V
V
ADMAX
DC input voltage AD03 inputs
0.5
8.5
V
V
OMAX
DC output voltage
0.5
V
DD
+0.5
V
I
IKMAX
DC diode input current, all inputs
10
mA
I
OKMAX
DC diode output current
10
mA
I
OLMAX
Continuous output current, digital outputs
4
mA
T
stg
Storage temperature
55
150
C
NOTES:
1. Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only and
functional operation of the device at these or any conditions other than those described in the Absolute Maximum Rating section of this
specification is not implied.
2. This product includes circuitry specially designed for the protection of its internal devices from damaging effects of excessive static charge.
Nonetheless, it is suggested that conventional precautions be taken to avoid submitting the UCB1100 to conditions exceeding the maximum
ratings.
3. Parameters are valid over the operating ambient temperature unless otherwise specified. All voltages are with respect to the V
SSD
pin,
unless otherwise noted.
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
5
4.0
DC ELECTRICAL CHARACTERISTICS
T
amb
= 0
C to 70
C, V
SSD
= V
SSA1
= V
SSA2
= V
SSA3
= 0V, sibclk = 10MHz, audio_divisor = 12, telecom_divisor = 40.
Voltage with respect to the V
SSD
pin, unless otherwise specified.
SYMBOL
PARAMETER
NOTES
LIMITS
UNIT
SYMBOL
PARAMETER
NOTES
MIN
TYP
MAX
UNIT
V
DDD
digital supply voltage
3.0
3.3
3.6
V
V
DDA1
analogue supply voltage (excl.speaker driver)
3.0
3.3
3.6
V
V
DDA2
analogue supply voltage (speaker driver only)
3.0
3.3
3.6
V
V
SSA2
analogue ground voltage wrt. V
SSD
0.4
0
0.4
V
V
SSA3
analogue ground voltage wrt V
SSD
0.4
0
0.4
V
I
DDD
digital supply current,
Note 1
full functionality
19
mA
only audio codec activated
17
mA
only telecom codec activated
19
mA
only touch screen activated
15
mA
only adc activated
15
mA
no functions activated, sibclk stopped
10
A
I
DDA1
analogue supply current,
Note 1, Note 2
full functionality
3.8
mA
only audio codec activated
1.5
mA
only telecom codec activated
1.7
mA
only touch screen activated
0.4
mA
only adc activated
0.5
mA
no analogue functions activated
<10
A
I
DDA2
total speaker driver supply current
Note 1, Note 2
full functionality
0.2
mA
only audio codec activated
0.2
mA
only telecom codec activated
10
A
only touch screen activated
10
A
only adc activated
10
A
no analogue functions activated
10
A
V
TSCB
touch screen bias voltage
1.8
V
I
TSCB
maximum touch screen bias current
10
mA
V
ADFS
full scale voltage ad0ad3 inputs
7.5
V
V
TSFS
full scale input touch screen inputs
7.5
V
V
IL
input low voltage
0.5
0.3*V
DDD
V
V
IH
input high voltage
0.7*V
DDD
V
DDD
+0.5
V
V
OL
output low voltage
I
OL
=2mA
0.2*V
DDD
V
V
OH
output high voltage
I
OH
=2mA
0.8*V
DDD
V
f
SIBCLK
clock frequency
0
10
15
MHz
T
amb
Operating Ambient Temperature
0
70
C
NOTES:
1. Indicative value only. Value will be frozen following silicon measurements.
2. Excluding connected touch screen and speaker load currents.
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
6
5.0
PINOUT
io3
io2
io1
io0
vddd
not used
tspx
tsmy
tsmx
tspy
vssa3
ad0
vddd
io6
io5
io4
not used
irqout
sibdin
sibclk
sibdout
sibsync
nreset
vssd
io7
io8
io9
adcsync
vssd
not used
vssa2
spkrn
sprkp
vdda2
toutp
toutn
test
tinn
tinp
vrefbyp
vdda1
vssa1
not used
micgnd
micp
ad3
ad2
ad1
12
11
10
9
8
7
6
5
4
3
2
1
25
26
27
28
29
30
31
32
33
34
35
36
48
47
46
45
44
43
42
41
40
39
38
37
13
14
15
16
17
18
19
20
21
22
23
24
UCB1100
LQFP48
TOP VIEW
SN00127
Figure 2.
LQFP48 (SOT313-2)
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
7
5.1
Pinlist
SYMBOL
PINNING
PIN TYPE
RESET
DESCRIPTION
NOTE
SYMBOL
LQFP48
PIN TYPE
STATE
DESCRIPTION
NOTE
vddd
32, 48
supply
digital supply
vssd
5, 37
ground
digital ground
1
vdda1
17
supply
analogue supply
vssa1
18
ground
analogue ground
1
vdda2
10
supply
analogue speaker driver supply
vssa2
7
ground
analogue speaker driver ground
vssa3
26
ground
touch screen switch matrix ground
sibclk
41
CMOS input
SIB serial interface master clock
sibdin
42
CMOS input
SIB data input
sibdout
40
CMOS output
`0' / Hi-Z
SIB data output
2
sibsync
39
CMOS input
SIB synchronization
irqout
43
CMOS output
active-High
`0'
interrupt output
micp
21
analogue input
Hi-Z
microphone signal input
micgnd
20
analogue input
Hi-Z
microphone ground switch input
sprkp
9
analogue output
Hi-Z
positive speaker output
3
spkrn
8
analogue output
Hi-Z
negative speaker output
3
tinp
15
analogue input
Hi-Z
positive telecom codec input
3
tinn
14
analogue input
Hi-Z
negative telecom codec input
3
toutp
11
analogue output
Hi-Z
positive telecom codec output
3
toutn
12
analogue output
Hi-Z
negative telecom codec output
3
ad03
2522
analogue input
Hi-Z
analogue high voltage inputs
tspx
30
analogue IO
Hi-Z
positive X-plate touch screen
tsmx
28
analogue IO
Hi-Z
negative X-plate touch screen
tspy
27
analogue IO
Hi-Z
positive Y-plate touch screen
tsmy
29
analogue IO
Hi-Z
negative Y-plate touch screen
adcsync
4
digital input
adc synchronization pulse input
vrefbyp
16
analogue IO
Hi-Z
external reference voltage input, external filter connection
io09
3336,
4547,
13
CMOS IO
input
general purpose IO pins
nreset
38
CMOS input
active-Low
asynchronous reset input
test
13
CMOS input
`0'
test mode protection
4
not used
6, 19,
31, 44
not connected pins
NOTES:
1. The vssd and vssa1 pins are connected to each other within the UCB1100.
2. The first 64 bits of the sib frame will be `0', the remaining bits in the sib frame will be Hi-Z.
3. The spkrp/spkrn, tinp/tiln and toup/toutn are differential pairs.
4. The test pin contains a internal pull down. This pin should be connected to vssd in normal mode of the UCB1100.
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
8
6.0
FUNCTIONAL DESCRIPTION
The UCB1100 consists of several analogue and digital sub circuits
which can be programmed via the Serial Interface Bus (SIB). This
enables the user to set the UCB1100 functionality according actual
application requirements.
6.1
Audio codec
The audio codec contains an input channel, built up from a 64 times
oversampling sigma delta analogue to digital converter (ADC) with
digital decimation filters and a programmable gain microphone
preamp. The output path consists of a digital up sample filter, a 64
time oversampling 4 bit digital to analogue converter (DAC) circuit
followed by a speaker driver, capable of driving directly a low
impedance bridge tied (BTL) speaker. The output path features
digitally programmable attenuation and a mute function. The audio
codec also incorporates a loopback mode, in which codec output
path and the input path are connected in series.
The audio sample rate is derived from the SIB interface clock pin
(SIBclk) and is programmable through the SIB interface. The audio
sample rate is given by the following equation:
Fsa
+
(2 *
Fsibclk)
(64 *
audio_divisor)
(5
t
audio_divisor
t
128)
For example, a serial clock of 10 MHz, with a divisor of 14, results in
an audio sample rate of 22.321kHz. Both the rising and the falling
edges of the sibclk are used in case an odd audio_divisor is set.
Thus a 50% duty cycle of the sibclk signal is mandatory to obtain
time equidistant sampling with odd divisors.
The frequency response of the audio codec depends mainly on the
selected sample rate, since the bandwidth is limited in the down and
up sampling filters. These digital filters both contain several FIR and
IIR low pass filters and a DC removal filter (high pass filter). A 1st
order analogue anti aliasing filter is implemented at the input of the
microphone input to prevent aliasing in the adc path. A 3rd order
smoothing filter is implemented between dac and speaker driver
stage to reduce the spurious frequencies at the speaker outputs.
The audio codec input (=ADC) and output (= DAC) paths can be
enabled individually by setting the audio_adc and/or audio_dac bits
in the audio control register B. These enable bits operate both on
the associated analogue and digital functions, for optimal power
control of both the analogue and the digital parts.
vdda2
vssa2
spkrp
spkrn
mute
4 bit DAC
64fsa
4
64fs
digital
volume
control
audio_output_enable
attn[4,5]
attn[0,3]
loopback
mux
gain[0,2]
1 bit ADC
64fsa
1
64fs
audio_input_enable
gain[3,4]
vssa1
micgnd
micp
loop input
Sinc4
FIR
16
DC
removal
half band
WDF
2
half band
WDF
2
+3dB
round
up
12
fs
half band
FIR
2
round
up
half band
WDF
2
+3dB
2
DC
removal
12
fs
low pass
FIR
2
interpolator
loop input
noise
shaper
4
SN00128
Figure 3.
Detailed Block Diagram Audio codec
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
9
micp
micgnd
vssa1
vdda1
micp
micgnd
vssa1
vdda1
UCB1100
UCB1100
`Passive' Microphone
`Active' Microphone
SN00129
Figure 4.
Possible Microphone Connections
The UCB1100 audio codec input path accepts microphone signals
directly, only a DC blocking capacitor is needed, since the micp input
is biased around 1.4V. The `ground' side of the microphone is either
connected to the analogue ground (vssa1) or to the micgnd pin of
the UCB1100. The latter will decrease the current consumption of
active microphones, since the micgnd pin is made Hi-Z when the
audio codec input path is disabled.
The full scale input voltage of the audio input path is programmable
in 1.5dB steps by setting the appropriate data in the
audio-input-gain
bits in the audio control register A.
A clip detection circuit will inform the user whenever the input
voltage exceeds the maximum input voltage. In that case the
clip
detect status bit in audio control register B is set. An interrupt is
generated on the irqout pin of the UCB1100 whenever the
enable
audio clip detect rising interrupt or the enable audio detect falling
edge interrupt bit is set in the rising edge interrupt enable or falling
edge interrupt control register B is set.
analog attenuation
digital attenuation
0dB
24dB
48dB
0dB
21dB
24dB
48dB
69dB
programmed attenuation
SN00130
Figure 5.
Analogue and Digital Attenuation Settings
Audio Output Path
The output level can be attenuated in 3dB steps down to -69dB. The
8 highest attenuation steps are implemented in the analogue
circuitry, while the two 24dB steps are implemented in the digital
domain. This preserves the `audio quality' of the output signal at
lowest attenuation settings. The speaker driver is muted when the
audio-mute bit in the audio control register B is set. The speaker
driver will remain activated in that case, however no signal is
produced by the speaker driver circuitry.
UCB1100
UCB1100
UCB1100
spkrp
spkrn
spkrp
spkrp
spkrn
spkrn
Bridge Tied
Speaker
Load
Single Ended Speaker Connections
SN00131
Figure 6.
Possible Speaker Connections
The speaker driver is designed to directly drive a bridge tied load
(BTL). This yields the highest output power and it does not require
external DC blocking capacitors. The speaker driver also accepts
single ended connection of a speaker, in which case the maximum
output power is reduced to a quarter of the BTL situation.
Consequently this way of connecting the speaker to the speaker
driver reduces the power consumption of the speaker driver in the
UCB1100 by a factor of 2. Figure 6 shows possible ways to connect
a speaker to the UCB1100.
The audio input and output path are activated independently; the
input path is enabled when the
audio-input-enable bit is set, the
output path is enabled when the
audio-output-enable bit is set in the
audio control register B. This provides the user the means to reduce
the current consumption of the UCB1100 if one part of the audio
codec is not used in the application.
The audio codec has a loopback mode for system test purposes,
which is activated when the
audio_loopback enable bit in the audio
control register B is set. This is an analogue loopback which
internally connects the output of the audio output path to the input of
the audio input path, (see Figure 3). In this mode the normal
microphone input is ignored, but the speaker driver can be operated
normally.
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
10
6.1.1
Audio Input Specifications
SYMBOL
PARAMETER
CONDITIONS
LIMITS
UNIT
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
F
SA
audio sample frequency
26
kHz
V
INAM
full scale input voltage
0 dB gain setting
0.28
V
pp
V
MICP
DC bias voltage micp input
audio input path enabled
1.4
V
R
INPAI
input impedance
audio input path enabled
25
k
R
HINE
impedance micgnd to vssa1
audio input path enabled
100
G
SA
gain step size
1.3
1.5
1.7
dB
N
AGS
number of gain steps
32
G
mA
maximum gain
46.5
dB
G
EAR
gain error (accuracy of gain setting)
0 dB gain setting,
full scale input voltage
1
0
1
dB
ROES
AI
resolution audio input
12
bit
DNA
AI
differential non linearity audio input ADC
0.9
LSB
THUD
AI
total harmonic distortion
0db input gain selected
0.28Vpp, 1kHz to micp
0.03
%
THD
MGAI
total harmonic distortion
46.5dB gain setting,
1mVpp, 1kHz to micp
0.1
%
SNR
AI
signal to noise ratio
audio input
0dB input gain selected
0.28Vpp, 1kHz to micp
65
dB
SNR
MGAI
signal to noise ratio
46.5dB gain selected
1mVpp, 1kHz to micp
50
dB
RIP
IA
pass band ripple
F
PLAI
<Fsig < F
PHAI
0.5
dB
SBR
IA
stop band rejection
audio input
F
SHAI
<Fsig.<20kHz
70
dB
E
IA
out of band rejection
audio input
F > 20kHz
t.b.f.
mVrms
NOTE: Coding scheme for ADC output data is 2's complement.
F
SHA
F
PHA
FREQUENCY (Hz)
F
PLA
RIP
IA
0dB
SBR
IA
SN00132
Figure 7.
Audio Input Path Frequency Response
F
PLA
= 0.00016 * F
SA
F
PHA
= 0.42 * F
SA
F
SHA
= 0.6 * F
SA
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
11
6.1.2
Audio Output Specifications
SYMBOL
PARAMETER
CONDITIONS
LIMITS
UNIT
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
V
OFFIA
offset error
No signal applied to micp
0
LSB
V
OOA
full scale output voltage
0dB attenuation,
16ohm speaker
differential SpkrpSpkrn
3.2
V
pp
V
OFFOA
offset error
16ohm speaker
50
mV
pp
V
SPK
DC bias voltage
spkrp and spkrn pin
Audio output path enabled
1.4
V
A
SOA
attenuation step size
2.8
3.0
3.2
dB
NSOA
number of attenuation steps
24
A
MOA
maximum attenuation
69
dB
ROES
OA
resolution
12
bit
DNA
OA
differential non linearity DAC
0.9
LSB
THUD
OAS
total harmonic distortion
16
speaker
0dB attenuation
20Hz to 20kHz
0.5
2
%
THUD
OAH
total harmonic distortion
1k
headphone
0dB attenuation
20Hz to 20kHz bandwidth
0.03
%
SNR
OAS
signal to noise ratio
16
speaker
0dB attenuation
20Hz to 20kHz bandwidth
40
80
dB
SNR
OAH
signal to noise ratio,
1kH
headphone
0dB attenuation
20Hz to 20kHz bandwidth
65
80
dB
RIP
OA
pass band ripple
F
PLAO
< Fsig < F
PHAO
0.5
dB
F
SUOA
cut off frequency upper stop band
0.6
F
SA
SBR
OA
stop band rejection
F
SHAO
<Fsig.<20kHz
70
dB
E
IOA
integrated out of band energy
F > 20kHz
30
mVrms
Z
SPKR
speaker impedance
8
16
NOTE: Coding scheme for DAC input data is 2's complement.
F
SHA
F
PHA
FREQUENCY (Hz)
F
PLA
RIP
OA
0dB
SBR
OA
SN00133
Figure 8.
Audio Output Filter Frequency Response
F
PLA
= 0.00016 * F
SA
F
PHA
= 0.42 * F
SA
F
SHA
= 0.6 * F
SA
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
12
6.2
Telecom codec
The telecom codec contains an input channel, built up from a 64
times oversampling sigma delta analogue to digital converter (ADC)
with digital decimation filters, programmable attenuation and build in
sidetone suppression circuit. The output path consist of a digital up
sample filter, a 64 time oversampling 4 bit digital to analogue
converter (DAC) circuit followed by a differential output driver,
capable of directly driving a 600ohm isolation transformer. The
output path includes a mute function. The telecom codec also
incorporates a loopback mode, in which codec output path and the
input path are connected in series.
The telecom sample rate is derived from the SIB interface clock pin
(sibclk) and is programmable through the SIB interface. The telecom
sample rate is given by the following formula:
Fst
+
(2 *
Fsibclk)
(64 *
telecom_divisor)
(5
t
telecom_divisor
t
128)
For example, a sibclk of 10 MHz, with a divisor of 40, results in a
telecom sample rate of 7.813kHz. Both the rising and the falling
edges of the sibclk are used in case an odd telecom_divisor is set.
In that case a 50% duty cycle of the sibclk signal is mandatory to
obtain time equidistant sampling.
The input path of the telecom codec has a programmable
attenuation. It also implements a voice band filter, which consists of
an digital low pass filter, which is a part of the decimation filter.
Therefore the pass band of the voice band filter is determined by the
selected telecom codec sample rate. This voice band filter is
activated by the
high pass enable bit in the telecom control register
B. The resulting telecom input filter curves are given in Figures 11
and 12.
The output section of the telecom codec is designed to interface with
a 600 ohm line through an isolation transformer. The built in mute
function is activated by the
mute bit in the telecom control register B.
The output driver remains active in the mute mode, however no
output signal is produced.
tinp
tinn
toutp
toutn
mute
echo on
loopback
mux
attenuation
1 bit ADC
effect
4 bit DAC
effect
4
64fs
telecom output enable
4
64fs
side tone suppression
telecom input enable
loop inputs
Sinc4
FIR
16
DC
removal
half band
WDF
2
half band
WDF
2
+3dB
high pass
FIR
round
up
14
fs
low pass
FIR
2
half band
FIR
2
round
up
loop inputs
half band
FIR
2
+3dB
half band
FIR
2
DC
removal
14
fs
noise
shaper
interpolator
4
SN00134
Figure 9.
Detailed Block Diagram Telecom codec
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
13
Rg
Rg
Rs
Rs
Ri
Ri
toutn
tinn
tinp
toutp
Rt
Rt
Rt
Rt
Ro
Ro
1:1 transformer
A
B
SN00135
Figure 10.
Telecom codec Sidetone Suppression Circuitry
Shown with the Typical Connection between UCB1100 and
Telephone Line (No Protections Circuits Shown)
An important built in feature of the telecom codec is the sidetone
suppression circuit. The sidetone suppression circuit is activated
when the
sidetone suppression enable bit in the telecom control
register B is set. The telecom input signal contains a large part of
the telecom output signal Tout, when the sidetone suppression
circuit is disabled. The available dynamic range of the telecom input
is occupied largely by the telecom output voltage.
The sidetone suppression circuit subtracts a part of the telecom
output signal from the telecom input signal when activated. The
available dynamic range is in that case used more effectively than
without sidetone suppression.
The built in side tone suppression circuit, shown in Figure 9, has a
fixed subtraction ratio, set be the resistors Rs and Ri, which equals
600 / 456. This ratio is calculated from the following relations:
The impedance seen by the telephone line equals:
Rline
+
2 *
Rt
)
Rt
)
Ro * Ri
Ro
)
Ri
In which Rt represents winding resistance of the transformer, divided
by 2. Assuming Ri >> Ro then
Rline
+
Rt
)
Rt
)
Ro
+
600
2
+
300
A typical transformer has 156 ohm winding impedance, thus Re
should be 144 ohm. The ratio of the telecom input and output
voltage is therefore
Tin
+
Tout *
156
)
300
156
)
300
)
144
+
Tout *
456
600
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
14
6.2.1
Telecom Input Specifications
SYMBOL
PARAMETER
CONDITIONS
LIMITS
UNIT
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
F
ST
sample frequency
10
kHz
V
INTM
full scale input voltage
0 dB attenuation setting
0.519
V
p
V
TIN
DC bias voltage Tinp / Tinn pins
telecom input path enabled
1.4
V
A
SIT
attenuation step size
6
dB
N
STI
number of attenuation steps
2
A
MTI
maximum attenuation
6
dB
A
ERTI
attenuation error
(accuracy of attenuation setting)
0 dB attenuation setting,
full scale input voltage
0.5
0
0.5
dB
R
TI
input impedance
25
k
SINAD
TI
total harmonic distortion
+ noise to signal ratio
full scale input signal
70
dB
SINAD
TIS
total harmonic distortion
+ noise to signal ratio
43dBm input voltage
32
dB
DNL
TI
differential non linearity ADC
2
LSB
RES
TI
resolution
14
bit
RIP
TI
pass band ripple, no voice filter
F
PLTI
< Fsig < F
PHTI
0.6
dB
RIP
VTI
pass band ripple, voice filter activated
F
VHTI
< Fsig < F
PHTI
0.6
dB
SBR
VTI
stop band rejection,
voice filter activated
Fsig < F
VLTI
30
dB
SBR
HTI
stop band rejection
F
SHTI
<Fsig.<F
ST
55
dB
S
SUP
sidetone suppression effectiveness
600
line,
1:1 line transformer with
156
winding resistance
20
dB
NOTE: Coding scheme for ADC output data is 2's complement.
F
SHT
F
PHT
FREQUENCY (Hz)
F
PLT
RIP
TI
0dB
SBR
HTI
SN00136
Figure 11.
Telecom Input Frequency Response,
No Voice Filter
F
SHT
F
PHT
FREQUENCY (Hz)
F
VLT
RIP
TI
0dB
SIB
HTI
F
VHT
SIB
VTI
SN00137
Figure 12.
Telecom Input Frequency Response,
Voice Filter Enabled
F
PLT
= 0.00016 * F
ST
F
PHT
= 0.42 * F
ST
F
SHT
= 0.6 * F
ST
F
VLT
= 0.018 * F
ST
F
VHT
= 0.05 * F
ST
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
15
6.2.2
Telecom Output Specifications
SYMBOL
PARAMETER
CONDITIONS
LIMITS
UNIT
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
F
ST
sample frequency
10
kHz
V
OOT
full scale output voltage
differential Toutp/Toutn
4.0
4.4
V
pp
V
TOUT
DC bias voltage
Toutp / Toutn pins
telecom output path
enabled
1.4
V
ROES
TO
resolution
14
bit
SINAD
TO
signal to noise + distortion
75
dB
RIP
TO
pass band ripple
0.6
dB
RIP
VTO
pass band ripple,
voice band filter activated
0.6
dB
SBR
VTO
stop band rejection,
voice filter activated
Fsig < F
VLT
SBR
TO
stop band rejection
F
SHT
< Fsig
70
dB
E
ITO
integrated out of band energy
Frequencies > F
ST
25
mVrms
Z
TELTO
minimal load impedance
600
V
OFFTO
offset error
(deviation of the analogue output from
zero with 0 code input to telecom out-
put path)
1200
load
50
mV
NOTE: Coding scheme for the DAC input data is 2's complement.
F
SHT
F
PHT
FREQUENCY (Hz)
F
PLT
RIP
TO
0dB
SBR
HTO
SN00138
Figure 13.
Telecom Output Frequency Response,
No Voice Filter
F
PLT
= 0.00016 * F
ST
F
PHT
= 0.42 * F
ST
F
SHT
= 0.6 * F
ST
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
16
6.3
Touch Screen Measurement Modes
The UCB1100 contains an on chip interface for a 4 wire resistive
touch screen. This interface supports three modes of touch screen
measurements, position, pressure and plate resistance.
6.3.1
Position Measurement
Two position measurements are needed to determine the location of
the pressed spot. First an X measurement, secondly a Y
measurement. The X plate is biased during the X position
measurement the X plate and the voltage on one or both Y terminals
(tspy, tsmy) measured. The circuit can been represented by a
potentiometer, with the tspy and/or tsmy electrode being the `wiper'.
The measured voltage on the tspy/tsmy terminal is proportional to
the X position of the pressed spot of the touch screen.
In the Y position mode the X plate and Y plate terminals are
interchanged, thus the Y plate is biased on the voltage on the tspx
and/or tsmx terminal is measured.
Vtscbias
Vposition
Xplate
tsmy
tspx
tspy
tsmx
SN00139
Figure 14.
Touch Screen Setup for Position Measurement
6.3.2
Pressure Measurement
The pressure used to press the touch screen can be determined. In
fact the contact resistance between the X and Y plate is measured,
which is a good indication of the size of the pressed spot and the
applied pressure. A soft stylus, e.g. a finger, leads to a rather large
contact area between the two plates when a large pressure is
applied. A hard stylus, e.g. a pen, leads to less variation in
measured contact resistance since the contact area is rather small.
One plate is biased at one or both terminals during this pressure
measurement, whereas the other plate is grounded, again on one or
both terminals. The current flowing through the touch screen is a
direct indication for the resistance between both plates. A
compensation for the series resistance, formed by the touch screen
plates itself will improve the accuracy of this measurement.
Xplate
tsmy
tspx
tspy
Vtscbias ipresure
tsmx
SN00140
Figure 15.
Touch Screen Setup for Pressure Measurement
6.3.3
Plate Resistance Measurement
The plate resistance of a touch screen varies typically a lot due to
processing spreads. Knowing the actual plate resistance makes it
possible to compensate for the plate resistance effects in the
pressure resistance measurements. Secondly the plate resistance
decreases when two or more spots on the touch screen are
pressed. In that case a part of one plate, e.g. the X plate is shorted
by the other plate, which decreases the actual plate resistance.
The plate resistance measurement is executed in the same way as
the pressure resistance measurement. In this case only one of the
two plates is biased and the other plate is kept floating. The current
through the connected plate is again a direct indication of the
connected resistance.
Xplate
tsmy
tspx
tspy
Vtscbias
iplate
tsmx
SN00141
Figure 16.
Touch Screen Setup for Plate Resistance
Measurement
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
17
6.4
Touch Screen Interface
The UCB1100 contains a universal resistive touch screen interface
for 4 wire resistive touch screen, capable of performing both
position, pressure and plate resistance measurements. In addition
the touch screen can be programmed to generate interrupts when
the touch screen is pressed. The last mode is also active when the
UCB1100 is set in the standby mode.
ts.. power
ts.. ground
analog mux
adc_input_sel
vssa3
vssa1
vdda1
tsc_mod_sel
tsc_mod_sel
to adc input
touch screen
bias voltage
touch screen
current monitor
mux
tspx
tspy
tsmx
tsmy
tsc_bias_ena
SN00142
Figure 17.
Block Diagram of the Touch Screen Interface
The touch screen interface connects to the touch screen by four
wires: tspx, tsmx, tspy and tsmy. Each of these pins can be
programmed to tbe floating, powered or grounded in the touch
screen switch matrix. The setting of each touch screen pin is
programmable by the
power ts.. and ground ts.. bits in the touch
screen control register. Possible conflicting settings (grounding and
powering of a touch screen pin at the same time) are detected by
the UCB1100. In that case the UCB1100 will ground the touch
screen pin.
The UCB1100's internal voltage reference (Vref) is as reference
voltage for the touch screen bias circuitry. This makes the touch
screen biasing independent of supply voltage and temperature
variations. Four low pass filters, one on each touch screen terminal,
are built in to minimize the noise coupled from the LCD into the
touch screen signals. An LCD typically generates large noise
glitches on the touch screen, since they are closely coupled.
Xplate
tsmy
tspx
tspy
Vdda
Rint
comparator
comparator
tsmx
SN00143
Figure 18.
Touch Screen Setup for Interrupt Detection
In addition to the measurements made above, the touch screen can
also act as an interrupt source. In this mode the X plate of the touch
screen has to be powered and the Y plate has to be grounded. In
this case the touch screen is not biased by the active touch screen
bias circuit, but by a resistor to vdda1. This configuration simply
biases the touch screen and the UCB1100 does not consume power
unless the touch screen is touched. The voltage on the X plate
terminals drops if the screen is pressed. This voltage drop is
detected by Schmitt trigger circuits, of which the outputs are
connected to the interrupt control block. An touch screen interrupt is
generated either when the touch screen is pressed (falling edge
enabled) or when the touch screen is released (rising edge
enabled). which can by used to activate the system around the
UCB1100 to start a touch screen readout sequence. The internal
Schmitt trigger circuits are connected to the tspx and tsmx signals
after the built in low pass filters. This reduces the number of
spurious interrupts, due to the coupling between the LCD screen
and the touch screen sensors.
Each of the four touch screen signals can be selected as input for
the built in 10 bit ADC, which is used to determine the voltage on the
selected touch screen pin. The flexible switch matrix and the multi
functional touch screen bias circuit enables the user of the UCB1100
to set each desired touch screen configuration.
The setting of the touch screen bias circuitry and the adc_input
multiplexer is determined by the setting of the
tsc_mod_sel bits in
the touch screen control register according the following table.
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
18
TOUCH SCREEN MODE SELECTION
tsc_mod_sel bits
selected mode
touch screen bias source
`selected' adc input
00
interrupt
resistor to vdda1
defined by adc_input_sel bits
01
pressure
touch screen bias circuit
touch screen current monitor
10
position
touch screen bias circuit
defined by adc_inp_sel bits
11
position
touch screen bias circuit
defined by adc_input_sel bits
SUMMARY OF TOUCH SCREEN MODES
Touch screen mea-
surement
tspx
tsmx
tspy
tsmy
touch screen
mode
touch screen
bias
X position
powered
1
grounded
1
adc input
2
adc input
2
position
enabled
Y position
adc input
2
adc input
2
powered
1
grounded
1
position
enabled
pressure 1
powered
1
powered
1
grounded
1
grounded
1
pressure
enabled
pressure 2
powered
floating
grounded
floating
pressure
enabled
pressure 3
floating
grounded
powered
floating
pressure
enabled
pressure 4
floating
powered
floating
grounded
pressure
enabled
pressure 5
grounded
floating
floating
powered
pressure
enabled
X plate resistance
powered
1
grounded
1
floating
floating
pressure
enabled
Y plate resistance
floating
floating
powered
1
grounded
1
pressure
enabled
interrupt
powered
powered
grounded
grounded
interrupt
disabled
3
NOTES:
1. The powered and grounded touch screen pins may be interchanged.
2. One of the two indicated touch screen pins have to be selected.
3. The touch screen bias has to be disabled in this mode by the user, to prevent false interrupts.
6.4.1
Touch Screen Specifications
SYMBOL
PARAMETER
CONDITIONS
LIMITS
UNIT
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
V
TSCBIAS
touch screen bias voltage
touch screen position mode
selected
1.8
V
I
TSCMAX
maximum touch screen current
touch screen position mode
selected
10
mA
R
TSCINT
maximum touch screen resistance to
generate an interrupt
touch screen interrupt mode
selected
2500
R
SWGND
on resistance ground switch
touch screen pin
programmed grounded
50
t
TSCSTR
start up time touch screen bias voltage
generator
25
s
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
19
6.5
10 bit ADC
The UCB1100 includes a 10 bit successive approximation analogue
to digital converter (ADC) with build in track and hold circuitry, an
analogue multiplexer to select 4 analogue inputs or the 5 touch
screen voltages and 4 switched resistive voltage dividers on the
analogue ad03 high voltage inputs. The ADC is used to readout the
touch screen inputs and it measures the voltage on the four
analogue high voltage inputs ad03.
The ADC is controlled through the SIB interface. It is enabled by the
adc_enable bit in register 10; the ADC circuitry, including the track
and hold circuitry does not consume any power when it is not
enabled.
A complete analogue to digital conversion consists of several
phases. First the ADC input selector must be set to the proper input.
Secondly the track and hold must track the signal; this requires a
certain settling time if the adc input was changed. After this time the
sample is taken. A calibration of the ADC circuitry is performed
before the actual conversion starts. The result of the conversion is
stored in the register 11 of the SIB interface, after the completion of
the conversion. An interrupt may be generated whenever a
conversion is completed, depending of the setting of the
adc_interrupt_ena bits in the sib register 2 and 3. The
adc_data_valid bit in the SIB register 11 indicates the status of the
ADC; it equals `0' when a ADC sequence is started and it equals `1'
when the ADC result is stored in the SIB register 11.
The ADC sequence is started in two ways. First it starts whenever
the
adc_start bit in register 10 is changed from `0' to `1'; this is the
case when the
adc_sync_ena bit in registers 10 equals `0'
(=default). Internal logic determines whether the adc input
multiplexer setting was changed in the sib frame, carrying the
adc_start bit transition. If this is the case, an additional tracking time
is added automatically.
The second mode of operation is activated when the adc_sync_ena
bit is set to `1'. In this mode the ADC conversion is not started by an
`0' to `1' transition of the
adc_start bis, but is `armed'. During the
arming situation the track and hold circuit tracks the selected input
signal. A sample is taken and the actual ADC conversion is started
when a rising edge is detected on the adcsync input pin.
mux
9 to 1
track & hold
10 bit ADC
10
to external register 11
ADC start
stop logic
adc_sync_ena
adc
start
sync
enable
internal reference
adcsync
SN00144
Figure 19.
Block Diagram of the 10 bit ADC Circuit
tadcena
tadctrk
tadccal
tconv
track
cal
conversion
track
adc_ena
adc_input_selection
adc_start
'adc state'
adc_dat_valid
adc_data
SN00145
Figure 20.
Timing Diagram of an ADC Conversion Sequence (adc_sync_ena=`0')
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
20
The ADC sequence is started in two ways. First it starts whenever
the
adc_start bit in register 10 is changed from `0' to `1'; this is the
case when the
adc_sync_ena bit in registers 10 equals `0'
(=default). Internal logic determines whether the adc input
multiplexer setting was changed in the sib frame, carrying the
adc_start bit transition. If this is the case, an additional tracking time
is added automatically.
The second mode of operation is activated when the adc_sync_ena
bit is set to `1'. In this mode the ADC conversion is not started by an
`0' to `1' transition of the
adc_start bis, but is `armed'. During the
arming situation the track and hold circuit tracks the selected input
signal. A sample is taken and the actual ADC conversion is started
when a rising edge is detected on the adcsync input pin.
The internal ADC start logic adds a fixed tracking time, when the
ADC input multiplexer was changed in the SIB frame with the `0' to
`1' transition of the adc_start bit. A rising edge on the adcsync pin
will not have any effect during this tracking time; the ADC sequence
will start on the first detected rising edge on the adcsyn pin after this
tracking time.
This mode is particulary useful when the internal ADC has to be
synchronized with the external systems. Typically it is used to
synchronize the readout of the touch screen with the driving of the
LCD screen, which is normally placed in the direct neighborhood of
the touch screen. Many spikes and a lot of `noise' are superposed
on the touch screen signals, due to the close coupling of the touch
screen and the LCD.
The UCB1100 contains four high voltage analogue inputs ad03
which can be selected by the ADC input multiplexer, besides the
already discussed touch screen interface signals. These high
voltage inputs optimized to handle voltages larger than the applied
supply voltage. The built in resistive voltage divider are only
activated if the corresponding analogue input is selected. The not
selected ad03 inputs are high ohmic resulting in minimal leakage
input leakage of these pins.
tadcena
tadctrk
tadcdead
tadcstrs
tadccal
tconv
track
cal
conversion
adc_ena
adc_input_selection
adc_start
adcsync
'adc state'
adc_dat_valid
adc_data
SN00146
Figure 21.
Timing Diagram of an ADC Conversion Sequence (adc_sync_ena=`1')
adc_inp_sel[2:0]
ad0 or ad1 or ad2 or ad3
adc
input
switch
SN00147
Figure 22.
ad0ad3 Resistive dividers
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
21
6.5.1
Specification Overview
SYMBOL
PARAMETER
CONDITIONS
LIMITS
UNIT
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
RES
ADC
resolution of ADC
10
bit
V
FSad
full scale ad03 inputs
7.17
7.5
7.9
V
R
INad
input impedance selected ad03 pin
50
75
100
I
Lad
input leakage current,
non selected ad03 pins
<1
10
A
DNL
ADC
differential non-linearity
0.1
0.5
lsb
INL
ADC
integral non linearity
0.5
2
lsb
t
conv
conversion time
110
t
sibclk
t
adccal
settling time
10
t
sibclk
tracking time
adc_sync_ena=`0'
t
adctrk
no adc input change
1
t
sibclk
adc input change
50
t
sibclk
tracking time
adc_sync_ena=`1'
t
adctrks
no adc input change
25
ns
adc input change
50
t
sibclk
t
hadcsync
10
ns
t
padcsync
6.6
On Chip Reference Circuit
The UCB1100 contains an on chip reference voltage source, which
generates the reference voltages for the 10 bit ADC and the
necessary internal reference voltages. Alternatively, the UCB1100
can be driven from an external reference voltage source.
The internal reference voltage can be monitored and filtered
additionally on the vrefbyp pin. Two bits in the ADC control register
determine the mode of operation of this reference voltage circuit.
The
vrefbyp_con bit connects the internal reference voltage to the
vrefbyp pin, while the
ext_vref_ena bit disables the internal
reference voltage and switches the UCB1100 into the external
voltage reference mode.
The internal reference circuit is activated only when one or more
analogue functions inside the UCB1100 is activated. This reduces
the current consumption of the analogue part in standby mode. The
external reference voltage source is also disconnected when all
analogue functions are disabled.
Internal
reference
circuitry
ext_vref_ena
vrefbyp_con
vrefbyp
internal
reference
voltage
aud_in_ena
aud_out_ena
tel_in_ena
tel_out_ena
tsc_bias_ena
adc_ena
&
&
SN00148
Figure 23.
Block Diagram of the Reference Circuit
6.6.1
Specification Overview
SYMBOL
PARAMETER
CONDITIONS
LIMITS
UNIT
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
V
REF
reference voltage
1.1
1.2
1.3
V
t
refstrt
start up time of internal reference voltage
circuit
50
t
sibclk
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
22
6.7
Serial Interface Bus
The UCB1100 serial interface bus (SIB) is compatible with industry
standard serial ports and devices, and is designed to connect
directly to a system controller. The sib protocol allows one or more
slave devices to be connected to the system controller. The data
transfer is always synchronous and it is frame based. The SIB
interface consists of four signals: sibddn, sibdout, sibclk and
sibsync.
Each SIB frame consists of at least 64 clock cycles. Typically 128
bits are used, divided into 2 sub frames of 64 bits each. The first
word (the bits 0 to 63) is read and/or written by the UCB1100, the
remaining bits may be used for communication between the system
controller and another slave device. The sibdout pin of the UCB1100
is default-stated for the bit 64 and higher in the SIB frame to prevent
bus conflicts with other slave devices. However when the
sib_zero_ena bit (control register 1) is set, the sibdout pin is forced
to zero for bit 64 and higher to prevent floating of the sibdout line
during this part of the sib frame in case when the UCB1100 is the
only slave device connected to the bus.
The UCB1100 always samples incoming data on the sibdin pin on
the falling edge of sibclk and it outputs data on the sibdout pin on
the rising edge of the sibclk. The start of a new sib frame is indicated
by a pulse on the sibsync line just before the start of this new sib
frame.
The applied clock signal to the sibclk pin is used as clock signal
inside the UCB1100; all internal clock signals are derived from that.
It is required that the sibclk signal is applied if one or more analogue
or digital functions is activated in the UCB1100; only the interrupt
controller is implemented synchronously. The sibclk may be stopped
when all digital and analogue functions are disabled; in that case the
lowest possible power consumption is meet. The sibclk should not
be stopped during a sib frame, but only at the end of the sib-frame,
to ensure that all analogue and digital functions are stopped
properly.
NOTE:
The interrupt controller is still active, due to its
asynchronous implementation. The UCB1100 can
therefore still generate interrupts to the system controller,
when the sibclk is stopped.
The generation of the audio and telecom sample clocks require that
the sibclk signal is symmetrical: a non symmetrical sibclk will lead to
non equidistant sample moments, when an odd frequency divisor is
set in either of the audio or telecom control registers.
sibclk
sibdin
sibdout
sibsync
sibclk
sibsync
sibdin
sibdout
sibclk
sibsync
sibdin
sibdout
SIB MASTER
UCB11001
SIB SLAVE 2
TO OTHER SIB SLAVES
SN00149
Figure 24.
Typical Connection Between the UCB1100 and the
System Controller
bit 0
bit 1
bit 2
bit 3
bit 63
bit 62
bit 64
bit 65
bit 126
bit 0
bit 127
sibclk
sibsync
sibdin
sibdout #1
sibdout #2
SN00150
Figure 25.
Serial Data Transmission of the UCB1100,
sibdout #1 in case sib_zero bit = `0', sibdout #2 in case sib_zero bit = `1'
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
23
6.7.1
SIB Data Format
The first 64 bits in the sib-frame are read and written by the
UCB1100 and they contain both audio and telecom codec data
fields, several control bits and a control register data field as is
defined in table below.
Sib frame bit
SIBDin
field definition
SIBDout
field definition
150
audio input path data [15:0];
bit 0 = MSB,
the 12 MSB bits are read.
audio output path data [15:0];
bit 0 = MSB,
the bits [15:12] are `0'
16
not read but reserved
fixed `0'
2017
control register address [3:0];
bit 0 = MSB
control register address [3:0];
bit 0 = MSB;
= copy of the register address as present in
the sibdin field in the same sib frame
21
write bit (write = 1)
fixed zero
2922
not read but reserved
fixed zeros
30
audio valid sample flag
audio valid flag
31
telecom valid sample flag
telecom valid flag
4732
telecom input path data [15:0];
bit 0 = MSB,
the 14 MSB bits are read.
telecom output path data [15:0],
bit 0 = MSB,
the bits [15:14] are `0''
6348
control register `write data [15:0];
bit 0 = MSB
control register read data [15:0];
bit 0 = MSB
NOTE:
Since the data transfer is completely synchronous, a given control register may be written many times, before the device feeding the data has a
chance to change the control bits. The UCB1100 does detect whether the data is changed or not.
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
24
6.7.2
Codec Data Transfer
The audio and telecom codecs both operate at a programmable sample rate slower than the data transfer rate of the serial bus. The codecs
sample the contents of the appropriate field each time their internal counters indicate that a new sample is necessary. They update the data
read by the serial interface in the same manner. The counters for the audio and telecom subsystems are reset each time the respective
subsection is turned on (whenever the audio/telecom input or output path enable bits are set) and counting begins at the next SIBSync input
pulse (see Figure 26). The controlling devices must be both frequency and phase synchronized to the sample rate counters within the UCB1100
in order to ensure correct operation.
tcodstr
#1
0
1
2
3
4
5
6
0
1
2
3
4
5
6
0
1
2
3
4
5
6
0
1
2
3
4
5
6
0
1
2
3
sibclk/128
sibdin
codec enable
sample counter
sample pulse
SN00151
Figure 26.
Start of the codec sample counters (divisor set to 7). Sibdin sub frame #1 contains the codec input and/or output path
enable bit, the codec enable signal is the `OR' function of the associated code input and output enable bit.
The codec data is loaded in the codec input register after the sub frame has been sent completely, when the appropriate data valid flag was set
in the sib frame. The codec input data is not refreshed, whenever the audio and/or telecom data valid flag equals `0' in the sub frame or when no
sibdin data is transmitted.
#1
#1
#1
#2
#2
#1
#1
#3
#3
#1
N
N+1
N+2
N+3
N+4
N+5
sibclk/128
sibdin stream
codec input data
SN00152
Figure 27.
Codec input data handshake protocol, sibdin frame #1 contains codec data and the data valid flag equals `1',
sib frame #2 contains codec data, but the data valid flag equals `0', sib frame #3 contains no data.
Codec data must be received by the UCB1100 in one of the SIB frames preceding the sample moment of the codec, it uses the last sample
received before the sample moment. In case no refreshed codec data has been sent, the UCB1100 re-uses the available `old' codec data
sample. This will lead to high distortion in the codec circuits.
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
25
6
0
1
2
3
4
5
6
0
1
2
3
4
5
6
0
1
2
3
4
5
6
0
1
2
3
4
5
6
0
1
2
3
4
5
sample D
6
0
1
2
3
sample E
A,#1
B,#1 B,#2
C,#1
D,#1
sample B
sample C
D,#1
D,#1
D,#1
sample D
E,#1
E,#2
sibclk/128
sample
sample pulse
sibdin
codec data
counter
SN00153
Figure 28.
Codec input data transfer, sib frame x,#1 contains sample x data with the associate data valid flag set to `1',
the sib frame indicated with x,#2 contain the codec sample x, with the associated data valid flag set to `0'.
The codec output data is transmitted in the first SIB frame following the sample moment of the codec. The sibdout data stream contains a data
valid bit for each codec (bit 30 and bit 31) to simplify the data transfer from the UCB1100 to the system controller. The audio and telecom data
valid bits are set to `1' in the sibdout data stream when the codec generate reliable data. This is the case when the codec circuitry is stabilized
after it was enabled. This mode of operation is chosen when the
dyn_vflag_ena bit (register 13) equals `0'. A second mode is available to
simplify the transfer of data, which is set when the
dyn_vflag_ena bit is set to `1'. In that case the audio and the telecom data valid flag bits will
be `1' in the sib frame following the codec sample moment, which contains at all times the most recent codec result.
6
0
1
2
3
4
5
6
0
1
2
3
4
5
6
0
1
2
3
4
5
6
0
1
2
3
4
N
N+1
N+2
N+2
N+3
N+3
N+4
5
6
0
1
2
3
4
5
N+4
N+5
N
N
N+1
N+2
N+2
N+3
N+3
N+4
N+4
6
0
1
2
3
N+6
N+5
sibclk/128
sample counter
sample pulse
audio data
telecom data
data valid flag
SN00154
Figure 29.
Sample counter synchronization (divisor set to 7), audio and telecom data placement shown in sibdout data stream,
including the associated audio/telecom data valid flags (dynamic data valid flag mode).
The audio and telecom codec data each are positioned as if they had 16 bits of resolution. For the 12-bit audio codec the low 4 bits are ignored
on input and forced to 0 on output. For the 14-bit telecom codec, the low 2 bits are treated similarly.
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
26
6.7.3
Control Register Data Transfer
The last 16 bits of the UCB1100 word is made up of control register
data. The selection of the control register and whether it is read or
written is defined by the control register address field [bit 17:20] and
the "write" bit [bit 21]. For a read action on the a control register, the
control register address field has to set to the desired control
register address and the "write" bit has to be set to zero in the
SIBDin stream, The read data is sent by the UCB1100 within the
control register data field of SIBDout during the same frame as the
read request occurred. In addition, during a read cycle, the control
register data field of SIBDin is ignored by the UCB1100 which
implies that no modifications of the UCB1100 settings can be
performed when the "write" bit equals zero in the SIBDin
data-stream.
For a write cycle ("write" bit = 1), the control register data contents of
SIBDin are written to the UCB1100 register selected by the register
address field after receipt of the complete first word (the update is
performed during the 64th bit in the SIB frame). This implies that the
control register data contents of SIBDout data-stream in a SIB frame
represents the previous contents of the selected control register.
The control register address in the sibdout data-stream is a copy of
the selected control register in the sibdin data-stream. These bits
show an additional delay since they pass additional circuitry in the
UCB1100.
The control register data is actually written in the control registers
after the transfer of the first sib word is completed. This implies that
the control register data is updated during bit 64 of the sib frame.
The control data is only updated when the write bit is `1' in the sib
frame. The control data will not be updated when the write bit equals
`0'. This simplifies the read out of control register data, since it is not
required to send `valid' data in the control register data field when a
control register is read, if the write bit is kept at `0'.
The control register data in the sibdout stream is sampled just
before the sib frame is started. This implies that the returned control
register data represents the `old' control data, in case new data was
provided in the sibdin data stream.
bit 64
tpcdu
bit 65
bit 66
bit 63
sibclk
sibsync
sibdin
control data
SN00155
Figure 30.
Control Register Update Timing
tsclsy
thclsy
tscldi
thcldi
tpcldo
tsibclk
tpdido
sibclk
sibsync
sibdin
sibdout
SN00156
Figure 31.
Timing Definitions SIB Interface
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
27
6.7.4
AC Electrical Characteristics
T
amb
= 0
C to 70
C, V
SSD
= V
SSA1
= V
SSA2
= V
SSA3
= 0V
V
DDD
= 3.3V
10%, V
DDA1
= 3.3V
10%, V
DDA2
= 3.3V
10%
SYMBOL
PARAMETER
NOTES
LIMITS
UNIT
SYMBOL
PARAMETER
NOTES
MIN
TYP
MAX
UNIT
1/t
sibclk
sibclk input frequency
0
15
MHz
t
hsibclk
/t
sibclk
duty cycle sibclk
Note 1
50
%
t
sclsy
sibsync valid to falling edge sibclk
ns
t
hclsy
sibsync hold after falling edge sibclk
ns
t
scldi
sibdin valid to falling edge sibclk
ns
t
hcldi
sibdin hold after falling edge sibclk
ns
t
pcldo
rising edge sibclk to valid sibdout
Note 2
20
ns
t
hcldo
sibdout hold after rising sibclk edge
Note 3
ns
t
pdido
valid sibdin to valid sibdout
25
ns
t
pcdu
NOTES:
1. This is a requirement when an odd divisor is set either in the audio or in the telecom codec.
2. This is valid for all sib frame bits 0 to 63, except bits 1720.
3. This is valid for the sib frame bits 1720.
6.8
General Purpose IOs
The UCB1100 has 10 programmable digital input/output (IO) pins.
These pins can be independently programmed as input or output
using the IO_mode[0:9] bits in the control register 1. The output data
is determined by the content of the io_data bits in the control register
0, while the actual status of these pins can be read from the
io_data[0:9] bits in the control register 0.
The data on the io[0:9] pins are feed into the interrupt control block,
where they can generate an interrupt on the rising and/or falling
edge of these signals.
io_dat_in[x]
io_dat_out[x]
io_dir[x]
to interrupt module
io[x]
SN00157
Figure 32.
Block Diagram of I/O Pin Circuitry
6.9
Interrupt Generation
The UCB1100 contains a programmable interrupt control block,
which can generate an interrupt for a `0' to `1' and/or a `1' to `0'
transition on one or more of the IO[0:9] pins, the audio and telecom
clip detect, the adc_ready signal and the tspx_low and tsmx_low
signals.
The interrupt generation mode is set by the
int_ris_ena bits in
register 2 and the
int_fal_ena bits in the control register 3. The
actual interrupt status of each signal can be read from the control
register 4. The interrupt status is clear whenever a `1' to `0' transition
is written in control register 4 for the corresponding bit. The irqout
pin presents the `OR' function of all interrupt status bits and can be
used to give an interrupt to the system controller.
The interrupt controller is implemented asynchronously. This provide
the possibly to generate interrupts when the sibclk is stopped,
e.g., an interrupt can be generated in power down mode, when the
touch screen is pressed or when the state of one of the io pins
changes.
D
R
irqout
int_stat[x]
register 4 (read)
fal_int_ena[x]
&
&
D
R
ris_int_ena[x]
`1'
int_clear[x]
reset
int.
source
`OR' tree
SN00158
Figure 33.
Block Diagram of the Interrupt Controller
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
28
6.10
Reset Circuitry
The nreset signal is captured in the UCB1100 using a asynchronous
pulse stretching circuit. The nreset signal may be pulled down when
the sibclk is still stopped. The internal circuitry remembers this reset
signal and generates an internal reset signal from at least 5 sibclk
periods.
D
R
D
D
'1'
NRESET
internal
reset
sibclk
Q
Q
Q
COUNT
3
&
arstn
SN00159
Figure 34.
Block Diagram of the Reset Circuitry
trsti
tlnrst
0
1
2
3
sibclk
nreset
arstn
count
internal reset
SN00160
Figure 35.
Timing Diagram of the Reset Circuitry
SYMBOL
PARAMETER
CONDITIONS
LIMITS
UNIT
SYMBOL
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNIT
t
lnrst
nreset pulse width
5
ns
t
rsti
width of internal reset signal
5 * t
sibclk
ns
t
pclrsti
delay between rising edge sibclk and internal reset
25
ns
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
29
7.0
MISCELLANEOUS
7.1
Power Routing Strategy
The UCB1100 has nine power supply pins, since the UCB1100
contains five power supply regions within the circuit. The analogue
and digital parts have their separate power supplies to reduce the
interference between these parts. The speaker driver circuit is
powered separately (vdda2/vssa2) from the other analogue circuit
parts and the touch screen switch matrix has its own ground pin
(vssa3). This separation in the analogue part reduces the
interference between the speaker driver and the touch screen switch
matrix, which has relatively large and fluctuating current
consumption and the remaining parts of the analog.
The vssd pins and the vssa1 pin are connected within the UCB1100
circuit. It is recommended to connect the vssd pins and the vssa1
directly to a ground plane on the PCB. The split in power supply
connections should be maintained on the PCB to get optimal
separation. Figure 36 shows the recommended PCB power supply
strategy.
UCB1100
vddd
vddd
vdda1
vdda2
vssa2
vssa3
vssa1
vssd
vssd
3.3V supply
SN00161
Figure 36.
Recommended Power Supply Connection Strategy
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
30
8.0
CONTROL REGISTER OVERVIEW
Address 0:
IO port data register
BIT
MODE
SYMBOL
REMARK
RESET
9:0
R/W
io_data[9:0]
The bits in the write register provide the data of the io pin when programmed as output.
The bits in the read register return the actual state of the associated io pin.
0
Address 1:
IO port direction register
BIT
MODE
SYMBOL
REMARK
RESET
9:0
R/W
io_dir[9:0]
If `1', the associated io pin is defined as output.
If `0', the associated io pin is defined as input
0
15
R/W
sib_zero
If `1', the sibdout pin is forced `0' during the second sib word.
If `0', the sibdout pin tristated during the second sib word
0
Address 2:
Rising edge interrupt enable register
BIT
MODE
SYMBOL
REMARK
RESET
9:0
R/W
io_ris_int[9:0]
If `1', the rising edge interrupt of the associated io pin is enabled
0
11
R/W
adc_ris_int
If `1', the rising edge interrupt of the adc_ready signal is enabled
0
12
R/W
tspx_ris_int
If `1', the rising edge interrupt of the tspx signal is enabled
0
13
R/W
tsmx_ris_int
If `1', the rising edge interrupt of the tsmx signal is enabled
0
14
R/W
tclip_ris_int
If `1', the rising edge interrupt of the telecom clip is enabled
0
15
R/W
aclip_ris_int
If `1', the rising edge interrupt of the audio clip is enabled
0
Address 3:
Falling edge interrupt enable register
BIT
MODE
SYMBOL
REMARK
RESET
9:0
R/W
io_fal_int[9:0]
If `1', the falling edge interrupt of the associated io pin is enabled
0
11
R/W
adc_fal_int
If `1', the falling edge interrupt of the adc_ready signal is enabled
0
12
R/W
tspx_fal_int
If `1', the falling edge interrupt of the tspx signal is enabled
0
13
R/W
tsmx_fal_int
If `1', the falling edge interrupt of the tsmx signal is enabled
0
14
R/W
tclip_fal_int
If `1', the falling edge interrupt of the telecom clip is enabled
0
15
R/W
aclip_fal_int
If `1', the falling edge interrupt of the audio clip is enabled
0
Address 4:
Interrupt clear/status register
BIT
MODE
SYMBOL
REMARK
RESET
9:0
W
io_int_clr[0:9]
A `0' to `1' transition clears the interrupt of the associate io pin
0
R
io_int_stat[9:0]
Returns the actual interrupt status of the associated io pin
11
W
adc_int_clr
A `0' to `1' transition clears the interrupt adc_ready signal
0
R
adc_int_stat
Returns the actual interrupt status of the adc_ready signal
12
W
tspx_int_clr
A `0' to `1' transition clears the interrupt of the tspx signal
0
R
tspx_int_stat
Returns the actual interrupt status of the tspx signal
13
W
tsmx_int_clr
A `0' to `1' transition clears the interrupt of the tsmx signal
0
R
tsmx_int_stat
Returns the actual interrupt status of the tsmx signal
14
W
tclip_int_clr
A `0' to `1' transition clears the interrupt of the telecom clip
0
R
tclip_int_stat
Returns the actual interrupt status of the telecom clip
15
W
aclip_int_clr
A `0' to `1' transition clears the interrupt of the audio clip
0
R
aclip_int_stat
Returns the actual interrupt status of the audio clip
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
31
Address 5:
Telecom control register A
BIT
MODE
SYMBOL
REMARK
RESET
6:0
R/W
tel_div[6:0]
Telecom codec sample rate divisor.
Valid values are between [0010000] (=16) and [1111111] (=127)
16
7
R/W
tel_loop_ena
If `1', the loopback mode of within the telecom codec is enabled.
0
Address 6:
Telecom control register B
BIT
MODE
SYMBOL
REMARK
RESET
3
R/W
high_pass_ena]
If `1', the voice band filter in the telecom input path is enabled
0
4
R
tel_clip
The bit returns the actual telecom clip detection status.
W
tel_clip
A `0' to `1' transition bit clears the telecom clip detection status
0
6
R/W
tel_att
If `1', the telecom input attenuation (6dB) is enabled.
0
11
R/W
side_sup_ena
If `1', the sidetone suppression circuit is activated
0
13
R/W
tel_mute
If `1', the telecom output is muted
0
14
R/W
tel_in_ena
If `1', the telecom input path is activated
0
15
R/W
tel_out_ena
If `1', the telecom output path is activated
0
Address 7:
Audio control register A
BIT
MODE
SYMBOL
REMARK
RESET
6:0
R/W
aud_div[6:0]
Audio codec sample rate divisor.
Valid values lie between [00000110] (=6) and [1111111] (=127).
6
11:7
R/W
aud_gain[4:0]
Audio input gain setting.
Values range from [00000] (no gain) to [11111] (46.5dB gain)
0
Address 8:
Audio control register B
BIT
MODE
SYMBOL
REMARK
RESET
4:0
R/W
aud_att[4:0]
Audio output attenuation setting.
Values range from [00000] (no attenuation) to [11111] (69dB attenuation).
0
6
R/W
aud_clip_ena
If `1', the audio clip detection circuitry is activated
0
8
R/W
aud_loop
If `1', the loopback mode in the audio codec is activated.
0
13
R/W
aud_mute
If `1', the audio output is muted
0
14
R/W
aud_in_ena
If `1', the audio codec input path is activated.
0
15
R/W
aud_out_ena
If `1', the audio codec output path is activated.
0
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
32
Address 9:
Touch screen control register
BIT
MODE
SYMBOL
REMARK
RESET
0
R/W
tspx_pow
If `1', the tspx pin is powered
0
1
R/W
tsmx_pow
If `1', the tsmx pin is powered
0
2
R/W
tspy_pow
If `1', the tspy pin is powered
0
3
R/W
tsmy_pow
If `1', the tspy pin is powered
0
4
R/W
tspx_gnd
If `1', the tspx pin is grounded
0
5
R/W
tsmx_gnd
If `1', the tsmx pin is grounded
0
6
R/W
tspy_gnd
If `1', the tspy pin is grounded
0
7
R/W
tsmy_gnd
If `1', the tspy pin is grounded
0
[9:8]
R/W
tsc_mode[1:0]
Touch screen operation mode
00 : interrupt mode
01 : pressure measurement mode
1x : position measurement mode
0
11
R/W
tsc_bias_ena
If `1', the touch screen bias circuitry is activated.
0
12
R/W
tspx_state
This bit returns the inverted state of the tspx pin,
`0' is high voltage (pen up), `1' is low voltage (pen down)
13
R/W
tsmx_state
This bit returns the inverted state of the tsmx pin,
`0' is high voltage (pen up), `1' is low voltage (pen down)
Address 10:
ADC control register
BIT
MODE
SYMBOL
REMARK
RESET
0
R/W
adc_sync_ena
If `1', the adc sync mode is activated
0
1
R/W
vrefbyp_con
If `1', the internal reference voltage is connected to the vrefbyp pin.
0
4:2
R/W
adc_input[2:0]
ADC input selection bits:
000: tspx
001: tsmx
010: tspy
011: tsmy
100 ad0
101: ad1
110: ad2
111: ad3
0
5
R/W
ext_ref_ena
If `1', an external reference voltage has to be applied to the vrefbyp pin
0
7
R/W
adc_start
A `0' to `1' transition starts the adc conversion sequence.
0
15
R/W
adc_ena
If `1', the adc circuit is activated
0
Address 11:
ADC data register
BIT
MODE
SYMBOL
REMARK
RESET
14:5
R
adc_data[9:0]
Returns the ADC result
0
15
R
adc_dat_val
Returns `0' if an adc conversion is in progress.
Returns `1' if the 0 adc conversion is completed and the adc data is stored in the
adc_data[9:0] register.
0
Address 12:
ID register
BIT
MODE
SYMBOL
REMARK
RESET
5:0
R
version[5:0]
Returns 000011 for all the UCB1100 circuits meeting this specification.
11:6
R
device[5:0]
Returns 000000 for all the UCB1100 circuits meeting this specification.
15:12
R
supplier[3:0]
Returns 0001 for all the UCB1100 circuits meeting this specification.
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
33
Address 13:
Mode register
BIT
MODE
SYMBOL
REMARK
RESET
0
R/W
aud_test
If `1', the analogue audio test mode is activated
(Note 1)
0
1
R/W
tel_test
If `1', the analogue telecom test mode is activated
(Note 1)
0
52
R/W
prod_test_mode
These bits select the build in production test modes
(Note 1)
0
12
R/W
dyn_vflag_ena
If `1', the dynamic data valid flag mode is activated for both the audio and the telecom
data valid flag.
0
13
R/W
aud_off_can
If `1', the offset cancelling circuit in the audio input path is disabled.
0
14
R/W
Reserved bit for special function
15
R/W
Reserved bit for special function
NOTES:
1. These bits can only be written if the test pin is `1'.
2. The functionality of the UCB1100 is changed when one or more test modes are activated.
Address 14:
Reserved
BIT
MODE
SYMBOL
REMARK
RESET
This register is reserved for future use.
Address 15:
Null register
BIT
MODE
SYMBOL
REMARK
RESET
15:0
R
Returns [1111111111111111] at all times
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
34
9.0
PACKAGE OUTLINES
9.1
LQFP48
LQFP48:
plastic low profile quad flat package; 48 leads; body 7 x 7 x 1.4 mm
SOT313-2
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
35
NOTES
Philips Semiconductors
Preliminary specification
UCB1100
Advanced modem/audio analog front-end
1998 May 08
36
10.0
DEFINITIONS
Definitions
Short-form specification -- The data in a short-form specification is extracted from a full data sheet with the same type number and title. For
detailed information see the relevant data sheet or data handbook.
Limiting values definition -- Limiting values given are in accordance with the Absolute Maximum Rating System (IEC 134). Stress above one
or more of the limiting values may cause permanent damage to the device. These are stress ratings only and operation of the device at these or
at any other conditions above those given in the Characteristics sections of the specification is not implied. Exposure to limiting values for extended
periods may affect device reliability.
Application information -- Applications that are described herein for any of these products are for illustrative purposes only. Philips
Semiconductors make no representation or warranty that such applications will be suitable for the specified use without further testing or
modification.
Disclaimers
Life support -- These products are not designed for use in life support appliances, devices or systems where malfunction of these products can
reasonably be expected to result in personal injury. Philips Semiconductors customers using or selling these products for use in such applications
do so at their own risk and agree to fully indemnify Philips Semiconductors for any damages resulting from such application.
Right to make changes -- Philips Semiconductors reserves the right to make changes, without notice, in the products, including circuits, standard
cells, and/or software, described or contained herein in order to improve design and/or performance. Philips Semiconductors assumes no
responsibility or liability for the use of any of these products, conveys no license or title under any patent, copyright, or mask work right to these
products, and makes no representations or warranties that these products are free from patent, copyright, or mask work right infringement, unless
otherwise specified.
Philips Semiconductors
811 East Arques Avenue
P.O. Box 3409
Sunnyvale, California 940883409
Telephone 800-234-7381
Copyright Philips Electronics North America Corporation 1998
All rights reserved. Printed in U.S.A.
Date of release: 05-98
Document order number:
9397 750 03868
Philips
Semiconductors
Data sheet
status
Objective
specification
Preliminary
specification
Product
specification
Product
status
Development
Qualification
Production
Definition
[1]
This data sheet contains the design target or goal specifications for product development.
Specification may change in any manner without notice.
This data sheet contains preliminary data, and supplementary data will be published at a later date.
Philips Semiconductors reserves the right to make chages at any time without notice in order to
improve design and supply the best possible product.
This data sheet contains final specifications. Philips Semiconductors reserves the right to make
changes at any time without notice in order to improve design and supply the best possible product.
Data sheet status
[1]
Please consult the most recently issued datasheet before initiating or completing a design.
PDF 
ZIP