4-67
4
G
E
N
E
RA
L
P
URPO
SE
A
M
P
L
IF
IE
RS
Product Description
Ordering Information
Typical Applications
Features
Functional Block Diagram
RF Micro Devices, Inc.
7625 Thorndike Road
Greensboro, NC 27409, USA
Tel (336) 664 1233
Fax (336) 664 0454
http://www.rfmd.com
Optimum Technology Matching Applied
Si BJT
GaAs MESFET
GaAs HBT
Si Bi-CMOS
SiGe HBT
Si CMOS
1
2
3
4
8
7
6
5
RF IN
GND
GND
GND
RF OUT
GND
GND
GND
RF2307
GENERAL PURPOSE AMPLIFIER
Broadband, Low Noise Gain Blocks
IF or RF Buffer Amplifiers
Driver Stage for Power Amplifiers
Final PA for Low Power Applications
Portable Battery Powered Equipment
Broadband Test Equipment
The RF2307 is a general purpose, low cost RF amplifier
IC. The device is manufactured on an advanced Gallium
Arsenide Heterojunction Bipolar Transistor (HBT) pro-
cess, and has been designed for use as an easily-cas-
cadable 50
gain block. Applications include IF and RF
amplification in wireless voice and data communication
products operating in frequency bands up to 3000MHz.
The device is self-contained with 50
input and output
impedances and requires only two external DC biasing
elements to operate as specified.
DC to 3000MHz Operation
Internally matched Input and Output
15dB Small Signal Gain
4dB Noise Figure
25mW Linear Output Power
Single Positive Power Supply
RF2307
General Purpose Amplifier
RF2307 PCBA
Fully Assembled Evaluation Board
4
Rev B2 010228
.156
.152
.022
.018
5
.056
.052
.195
.191
.240
.232
.050
.008
.004
MIN
.017
1
Package Style: SOP-8
4-68
RF2307
Rev B2 010228
4
G
E
N
E
RA
L
P
URPO
SE
A
M
P
L
IF
IE
RS
Absolute Maximum Ratings
Parameter
Rating
Unit
Supply Current
65
mA
Input RF Power
+10
dBm
Operating Ambient Temperature
-40 to +85
C
Storage Temperature
-40 to +150
C
Parameter
Specification
Unit
Condition
Min.
Typ.
Max.
Overall
T=25 C, V
CC
= 5.0V, R
C
= 22
,
Freq= 1000MHz
Frequency Range
DC to 3000
MHz
Gain
14.2
15.2
16.2
dB
Freq= 1000MHz
14.7
15.7
16.7
dB
Freq= 100MHz
Noise Figure
4
dB
Input VSWR
<2:1
Output VSWR
< 2:1
Output IP
3
+24
dBm
Output P
1dB
+10
+14
dBm
Saturated Output Power
+15
dBm
Reverse Isolation
> 18
dB
Power Supply
Operating Voltage
3.7
V
At pin 8
Operating Current
40
50
60
mA
V
CC
= 5.0V, R
C
= 22
Operating Current Range
20 to 65
mA
Caution! ESD sensitive device.
RF Micro Devices believes the furnished information is correct and accurate
at the time of this printing. However, RF Micro Devices reserves the right to
make changes to its products without notice. RF Micro Devices does not
assume responsibility for the use of the described product(s).
4-69
RF2307
Rev B2 010228
4
G
E
N
E
RA
L
P
URPO
SE
A
M
P
L
IF
IE
RS
Application Schematic
Pin
Function
Description
Interface Schematic
1
RF IN
RF input pin. This pin is NOT internally DC blocked. A DC blocking
capacitor, suitable for the frequency of operation, should be used in
most applications. DC coupling of the input is not allowed, because this
will override the internal feedback loop and cause temperature instabil-
ity.
2
GND
Ground connection. Keep traces physically short and connect immedi-
ately to ground plane for best performance.
3
GND
Same as pin 2.
4
GND
Same as pin 2.
5
GND
Same as pin 2.
6
GND
Same as pin 2.
7
GND
Same as pin 2.
8
RF OUT
RF output and bias pin. Biasing is accomplished with an external series
resistor and choke inductor to V
CC
. The resistor is chosen to set the DC
current into this pin to a desired level. At room temperature, this pin will
bias itself to 3.7V as long as the current is held between 20mA and
65mA. Thus the resistor value is determined by the following equation:
Care should also be taken in the resistor selection to ensure that the
current into the part never exceeds 65 mA over the planned oper-
ating temperature. This means that a resistor between the supply and
this pin is always required, even if a supply near 3.7V is available.
Because DC is present on this pin, a DC blocking capacitor, suitable for
the frequency of operation, should be used in most applications. The
supply side of the bias network should also be well bypassed.
R
V
SUPPL Y
3.7
(
)
I
CC
----------------------------------------
=
RF OUT
RF IN
1
2
3
4
8
7
6
5
RF OUT
22 pF
22
10 nF
22 pF
47 nH
22 pF
RF IN
V
CC
= 5 V
4-70
RF2307
Rev B2 010228
4
G
E
N
E
RA
L
P
URPO
SE
A
M
P
L
IF
IE
RS
Evaluation Board Schematic
(Download Bill of Materials from www.rfmd.com.)
Evaluation Board Layout
Uses same board as RF2306
1.27" x 1.02"
1
2
3
4
8
7
6
5
C2
100 pF
R1
27
C3
100 pF
C4
10 nF
L1
47 nH
C1
100 pF
SMA
J2
P1-3
RF OUT
(50
)
SMA
J1
RF IN
(50
)
NC
P1-3
P1
VCC
GND
1
2
3
2307400 Rev B
50
strip
50
strip
PDF 
ZIP