LB1960M
No. 6191-1/4
Specification
Absolute Maximum Ratings
at Ta = 25
C
Parameter
Symbol
Conditions
Ratings
Unit
Maximum supply voltage
V
CC
max
18
V
Allowable power dissipation
Pd max
With specified substrate *
600
mW
Maximum output current
I
OUT
ave
500
mA
I
OUT
peak
t
1 ms
1000
mA
Maximum output voltage
V
OUT
max
Internal
V
Maximum HB output current
I
H
max
10
mA
Operating temperature
Topr
30 to +85
C
Storage temperature
Tstg
55 to +150
C
* Specified substrate (114.3
76.1
1.5 mm
3
, glass epoxy)
Monolithic Digital IC
LB1960M
Fan Motor 2-Phase Half-Wave Driver
Package Dimensions
unit: mm
3032B-MFP8
63099RM(KI)
Ordering number : EN6191
[LB1960M]
Features
Dual power supply voltage design (5/12V) and wide voltage
handling range
(3V also supported for rotation functions only)
Constant-voltage Hall bias power supply (1.3V across HB-
GND) assures stable Hall output over entire temperature and
power supply voltage range. External limiting resistor not
required.
Built-in Hall amplifier with hysteresis (supports core
without commutating pole)
Built-in lockup protection and automatic recovery circuits
(External capacitor for rotation detection need only be 0.1
F, allowing compact, cost-saving design)
Built-in output transistor with output withstand voltage
24Vmax/output current 500 mA (average), 1A (peak)
Built-in thermal protection circuit
Compact MFP-8 package. Low external parts count, easy
wiring, and small PCB area allow use also with miniature
fan motors.
1
8
4
5
0.645
1.27
0.35
5.1
0.15
1.8max
1.5
0.1
0.625
4.4
5.15
6.4
SANYO : MFP8
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft's
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
LB1960M
No. 6191-2/4
Allowable Operating Ranges
at Ta = 25
C
Parameter
Symbol
Conditions
Ratings
Unit
Recommended supply voltage
V
CC
1
3.6 to 17
V
Common mode input voltage range
V
CO
M
0.2 to HB
V
Electrical Characteristics
at Ta = 25
C, VCC = 12V
Parameter
Symbol
Conditions
Ratings
Unit
min
typ
max
Circuit current
I
CC
In drive mode (CT = L)
2.3
4
mA
In lockup protection mode (CT = H)
3
5
mA
CT capacitor charge current
I
CT
1
V
CT
= 0.2V
0.8
1.2
2.0
A
Capacitor discharge current
I
CT
2
V
CT
= 8V
0.16
0.24
0.4
A
Capacitor charge/discharge current
ratio
R
CT
R
CT
= ICT1/ICT2
4.0
5.0
7.0
CT charge voltage
V
CT
1
6.8
7.2
7.6
V
CT discharge voltage
V
CT
2
1.4
1.6
1.8
V
Output limiter withstand voltage
V
OLM
Io = 1 mA
22.5
23.5
24.5
V
Output saturation voltage
V
O
sat
Io = 500 mA
1.0
1.3
V
Hall input sensitivity
V
HN
Including offset and hysteresis
6
12
mV
HB output H voltage
V
HBH
R
H
= 350
1.1
1.3
1.5
V
Thermal protection trigger temperature
T
TSD
Assured design target*
150
180
210
C
* Assured design target: Target value, not measured individually
Truth Table
IN
IN+
CT
OUT1
OUT2 Mode
H
L
L
L
H Rotating
L
H
H
L
H
off
off Lock-up protection activated
200
0
400
600
800
1000
30
0
30
60
90
120
Allowable power dissipation, Pd max mW
Pd max Ta
Ambient temperature, Ta
C
312mW
Specified substrate
(glass epoxy, 114.3
76.1
1.5mm
3
)
LB1960M
No. 6191-3/4
Sample Application Circuit
5/12V power supply (3.8 to 18V)
Precautions
If CT pin is connected to GND, the lockup protection and restart functions are disabled.
In a circuit configuration as shown above, a power supply/GND reverse connection will cause a current to flow as
follows: GND -> OUT -> coil -> power supply. The value of this current is limited by the coil resistance. If it is less
than 500 mA, the IC will not be destroyed. If required, insert a diode between V
CC
and the coil.
GND
VCC
OUT1
OUT2
0.1
F
CT
IN
IN+
HB+
H
RH
On-board parts
Pin Assignment
LB1960M
Top view
1
8
2
7
3
6
4
5
GND
OUT1
IN
HB+
IN+
VCC
CT
OUT2
LB1960M
No. 6191-4/4
This catalog provides information as of June, 1999. Specifications and information herein are subject to change
without notice.
PS
Block Diagram and Sample Application Circuit
Specifications of any and all SANYO products described or contained herein stipulate the performance,
characteristics, and functions of the described products in the independent state, and are not guarantees
of the performance, characteristics, and functions of the described products as mounted in the customer's
products or equipment. To verify symptoms and states that cannot be evaluated in an independent device,
the customer should always evaluate and test devices mounted in the customer's products or equipment.
SANYO Electric Co., Ltd. strives to supply high-quality high-reliability products. However, any and all
semiconductor products fail with some probability. It is possible that these probabilistic failures could
give rise to accidents or events that could endanger human lives, that could give rise to smoke or fire,
or that could cause damage to other property. When designing equipment, adopt safety measures so
that these kinds of accidents or events cannot occur. Such measures include but are not limited to protective
circuits and error prevention circuits for safe design, redundant design, and structural design.
In the event that any or all SANYO products(including technical data,services) described or
contained herein are controlled under any of applicable local export control laws and regulations,
such products must not be exported without obtaining the export license from the authorities
concerned in accordance with the above law.
No part of this publication may be reproduced or transmitted in any form or by any means, electronic or
mechanical, including photocopying and recording, or any information storage or retrieval system,
or otherwise, without the prior written permission of SANYO Electric Co. , Ltd.
Any and all information described or contained herein are subject to change without notice due to
product/technology improvement, etc. When designing equipment, refer to the "Delivery Specification"
for the SANYO product that you intend to use.
Information (including circuit diagrams and circuit parameters) herein is for example only ; it is not
guaranteed for volume production. SANYO believes information herein is accurate and reliable, but
no guarantees are made or implied regarding its use or any infringements of intellectual property rights
or other rights of third parties.
Thermal
protection
circuit
H
Control block
Constant
current
source
0.1
1
F
VCC
L2
L1
OUT1
OUT2
GND
C1
CT
IN
HB+
IN+
to
Constant
voltage output
circuit
PDF 
ZIP