Ordering number : ENN7027
O1901RM (OT) No. 7027-1/28
Overview
The LC75410E and 75410W are electronic volume
controllers that enable control of volume, balance, fader,
bass/treble/mid, loudness, input switching, and input gain
using only a small number of external components.
Functions
Volume: 0 dB to 79.5 dB in 0.5-dB steps, and
(161
positions) Balance function with separate L/R
control
Fader: rear output or front output can be attenuated
across 16 positions (in 1-dB steps from 0 dB to
2 dB, 2-dB steps from 2 dB to 20 dB, 10-dB
steps from 20 dB to 30 dB, and 45 dB,
60 dB,
)
Bass/treble/mid: Each band can be controlled in 1-dB
steps from 0 dB to 6 dB, and in 2-dB
steps from 8 dB to 12 dB.
Input gain: 0 dB to +18.75 dB (1.25-dB steps)
amplification is possible for the input signal.
Input switching: five input signals can be selected for
Left and for Right (Four are single-
ended inputs and one is a differential
input.)
Loudness: A tap is output from the 32 dB position of a
2 dB step volume control resistor ladder.
A loudness function can be implemented by
connecting an external RC circuit.
Features
On-chip buffer amplifier cuts down number of external
components
Low switching noise generated by on-chip switch
through use of silicon gate CMOS process, for low
switching noise when there is no signal
Low switching noise when there is a signal due to use
of on-chip zero-cross switching circuit
On-chip 1/2 VDD reference voltage circuit
Controls performed with serial input (CCB)
LC75410E, 75410W
SANYO Electric Co.,Ltd. Semiconductor Company
TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110-8534 JAPAN
Electronic Volume Controller
for Car Audio Systems
CMOS IC
Any and all SANYO products described or contained herein do not have specifications that can handle
applications that require extremely high levels of reliability, such as life-support systems, aircraft's
control systems, or other applications whose failure can be reasonably expected to result in serious
physical and/or material damage. Consult with your SANYO representative nearest you before using
any SANYO products described or contained herein in such applications.
SANYO assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or other
parameters) listed in products specifications of any and all SANYO products described or contained
herein.
CCB is a trademark of SANYO ELECTRIC CO., LTD.
CCB is SANYO's original bus format and all the bus
addresses are controlled by SANYO.
No. 7027-5/28
LC75410E, 75410W
Parameter
Symbol
Pin Name
Conditions
Ratings
Unit
min
typ
max
[Fader Block]
Input resistance
Rfed
LFIN, RFIN
25
50
100
k
0dB to 2dB
0.5
dB
Step setting error
ATerr
2dB to 20dB
1
dB
20dB to 30dB
2
dB
30dB to 60dB
3
dB
L/R balance
BAL
0.5
dB
[General]
Total harmonic distortion
THD (1)
V
IN
= 0dBV, f = 1 kHz
0.004
0.01
%
THD (2)
V
IN
= 10dBV, f = 10 kHz
0.006
0.01
%
Input crosstalk
CT
V
IN
= 1Vrms, f = 1 kHz
80
88
dB
L/R crosstalk
CT
V
IN
= 1Vrms, f = 1 kHz
80
88
dB
Maximum attenuated output
Vomin (1) V
IN
= 1Vrms, f = 1 kHz
80
88
dB
Vomin (2)
V
IN
= 1Vrms, f = 1 kHz
90
95
dB
INMUTE, fader
Output noise voltage
V
N
(1)
Flat overall, IHF-A filter
5
10
V
V
N
(2)
Flat overall, 20 to 20 kHzBPF
7
15
V
Current drain
I
DD
40
45
mA
Input high-level current
I
IH
CL, DI, CE, V
IN
= 9 V
10
A
Input low-level current
I
IL
CL, DI, CE, V
IN
= 0 V
10
A
Maximum input voltage
V
CL
THD = 1%, R
L
= 10 k
2.3
2.8
Vrms
flat overall, f
IN
= 1 kHz
Common-mode rejection ratio
CMRR
V
IN
= 0 dB, f = 1 kHz
45
70
dB
Continued from preceding page.
Control Timing and Data Format
To control the LC75410E and LC75410W input specified serial data to the CE, CL, and DI pins.
The data configuration consists of a total of 52 bits broken down into 8 address bits and 44 data bits.
CE
DI
D43
D42
D41
D40
D39
D38
D5
D4
D3
D2
D0 D1
A3
A2
A1
A0
B3
B2
B1
B0
CL
1
s
min
1
s
min
1
s min
T
DEST
1
s
min
1
s
min
1
s
min
CE
DI
CL
PDF 
ZIP
