LD14901-1

1. Application
This specification applies to color TFT-LCD module, LQ104V1DG21

(This specification is only applied for the module which has letter "A" at the end of the lot number of the
module.)

These specification sheets are the proprietary product of SHARP CORPORATION("SHARP) and include

materials protected under copyright of SHARP. Do not reproduce or cause any third party to reproduce
them in any form or by any means, electronic or mechanical, for any purpose, in whole or in part, without
the express written permission of SHARP .

The device listed in these specification sheets was designed and manufactured for use in general electronic

equipment.

In case of using the device for applications such as control and safety equipment for transportation(aircraft,

trains, automobiles, etc. ), rescue and security equipment and various safety related equipment which
require higher reliability and safety, take into consideration that appropriate measures such as fail-safe
functions and redundant system design should be taken .

Do not use the device for equipment that requires an extreme level of reliability, such as aerospace

applications, telecommunication equipment(trunk lines), nuclear power control equipment and medical or
other equipment for life support .

SHARP assumes no responsibility for any damage resulting from the use of the device which does not

comply with the instructions and the precautions specified in these specification sheets .

Contact and consult with a SHARP sales representative for any questions about this device .

2. Overview
This module is a color active matrix LCD module incorporating amorphous silicon TFT
(Thin Film Transistor). It is composed of a color TFT-LCD panel, driver ICs, control
circuit and power supply circuit and a backlight unit. Graphics and texts can be
displayed on a 640×3×480 dots panel with 262,144 colors by supplying 18 bit data signal
(6bit/color), four timing signals,+3.3V/ +5V DC supply voltage for TFT-LCD panel driving and
supply voltage for backlight.
The TFT-LCD panel used for this module is a low-reflection and higher-color-saturation
type. Therefore, this module is also suitable for the multimedia use.
Optimum viewing direction is 6 o'clock.
Backlight-driving DC/AC inverter is not built in this module.

LD14901-3

4. Input Terminals

4-1. TFT-LCD panel driving
CN1 Used connector:DF9MA-31P-1V (Hirose Electric Co., Ltd.)

Corresponding connector : DF9-31S-1V ( )
DF9A-31S-1V( )
DF9B-31S-1V( )

DF9M-31S-1V( )

Pin No. Symbol

Function

Remark

GND

Clock signal for sampling each data signal

Hsync Horizontal synchronous signal

Note1

Vsync Vertical synchronous signal

Note1

5 GND

6 R0

data signal(LSB)

7 R1

data signal

8 R2

data signal

9 R3

data signal

10 R4

data signal

11 R5

data signal(MSB)

12 GND

13 G0

data signal(LSB)

14 G1

data signal

15 G2

data signal

16 G3

data signal

17 G4

data signal

18 G5

data signal(MSB)

19 GND

20 B0

data signal(LSB)

21 B1

data signal

22 B2

data signal

23 B3

data signal

24 B4

data signal

25 B5

data signal(MSB)

26 GND

ENAB Signal to settle the horizontal display position

Note2

28 Vcc

3.3/5.0V power supply

29 Vcc

3.3/5.0V power supply

R/L

Horizontal display mode select signal

Note3

U/D

Vertical display mode select signal

Note4

The shielding case is connected with GND.

Note1480 line, 400 line or 350 line mode

is selected by the polarity combination

of the both synchronous signals.

Note2The horizontal display start timing is settled in

accordance with a rising timing of ENAB signal. In case ENAB is fixed "Low", the horizontal start timing is
determined as described in 7-2. Don't keep ENAB "High" during operation.

CN1 pin arrangement from module surface

(Transparent view)

Mode

480 lines

400 lines

350 lines

Hsync Negative Negative Positive

Vsync Negative Positive Negative

LD14901-4

Note3Note4

4-2. Backlight driving

Used connector : BHR-03VS-1(JST)
CN2CN3 Corresponding connector :SM02(8.0)B-BHS(JST)

Pin no.

Symbol

Function

HIGH

Power supply for lamp

(High voltage side)

This is electrically opened.

LOW

Power supply for lamp

(Low voltage side)

5. Absolute Maximum Ratings

Parameter Symbol Condition

Ratings

Unit

Remark

Input voltage

Ta=25 -0.3 Vcc0.3 Note1

+5V supply voltage

Vcc Ta=25 0 6

Storage temperature

Tstg

-30 70

Note2

Operating temperature (Ambient) Topa

-10 65

Note1CK,R0R5,G0G5,B0B5,Hsync,Vsync,ENAB, R/L, U/L

Note2Humidity95%RH Max. at Ta40.

Maximum wet-bulb temperature at 39 or less at Ta>40.

No condensation.

LD14901-5

6. Electrical Characteristics

6-1.TFT-LCDpaneldriving
Ta25

Parameter Symbol

Min.

Typ.

Max.

Unit

Remark

Supply voltage

Vcc

+3.0 +3.3 +5.0

+5.5

Note1

Icc

180 270

Vcc=3.3VNote2

Power
Supply Current dissipation

Icc

150 230

Vcc=5.0VNote2

Permissive input ripple voltage

100 mVp-p

Input voltage (Low)

0.3Vcc

Input voltage (High)

0.7Vcc

Note3

Input current (low)

OL1

1.0

=0V Note4

OL2

=0V Note5

OL3

800

=0V Note6

Input current (High)

OH1

1.0

=VccNote7

OH2

300

=VccNote8

OH3

800

=VccNote9

NOTE 1
Vcc-turn-on conditions

Vcc-dip conditions

Vcc-dip condition should also follow
The Vcc-turn-on conditions

Note2 Typical current situation : 16-gray-bar pattern.

480 line mode/Vcc=+3.3V/5.0V

Note3 CK,R0~R5,G0~G5,B0~B5,Hsync,Vsync,ENAB,

R/L,U/D

Note4 CK,R0~R5,G0~G5,B0~B5,Hsync,Vsync,

Note5 U/D,ENAB

Note6 R/L

Note7 CK,R0~R5,G0~G5,B0~B5,Hsync,Vsync,R/L

Note8 ENAB

Note9 U/D

0.3V

VCC

0.9VCC

0.3V

VCC

0.9VCC

Signal

2.7V

2.5V

VCC

R G B

G S 0

R G B

G S 4

R G B

G S 8

R G B

G S 5 6

R G B

G S 6 0

. . . .

LD14901-6

6-2. Backlight driving
The backlight system is an edge-lighting type with double CCFT (Cold Cathode

Fluorescent Tube). The characteristics of single lamp are shown in the following table.

Ta=25

Parameter

Symbol Min.

Typ.

Max. Unit

Remark

Lamp current

2.0 6.0 6.5

mArms Note1

Lamp power consumption

2.8

Note2

Lamp frequency

20 35 60

KHz Note3

Kick-off voltage

950 Vrms

Ta=25Note4

1250 Vrms

Ta =0Note4

1500 Vrms

Ta =-10Note4

Lamp life time

50000

hour Note5

Note1 Lamp current is measured with current meter for high frequency as shown below.

Note2 At the condition of I

=6.0mArms

Note3 Lamp frequency may produce interference with horizontal synchronous frequency,and
this may cause beat on the display. Therefore lamp frequency shall be detached as
much as possible from the horizontal synchronous frequency and from the harmonics
of horizontal synchronous to avoid interference.
Note4The open output voltage of the inverter shall be maintained for more than 1sec; otherwise
the lamp may not be turned on.
Note5Since lamp is consumables, the life time written above is referencial value and it is not
guaranteed in this specification sheet by SHARP.
Lamp life time is defined that it applied either or under this condition
(Continuous turning on at Ta=25, IL=6.0mArms)
Brightness becomes 50% of the original value under standard condition.
Kick-off voltage at Ta= -10 exceeds maximum value,1500Vrms.
In case of operating under lower temp environment, the lamp exhaustion is accelerated and the
brightness becomes lower.
(Continuous operating under for around 1 month under lower temp condition may reduce the
brightness to half of the original brightness.)
In case of such usage under lower temp environment, periodical lamp exchange is recommended.
Note6The performance of the backlight, for example life time or brightness, is much influenced
by the characteristics of the DC-AC inverter for the lamp. When you design or order the
inverter, please make sure that a poor lighting caused by the mismatch of the backlight and
the inverter (miss-lighting,flicker, etc.) never occur. when you confirm it, the module should
be operated in the same condition as it is installed in your instrument.
Note7 It is required to have the inverter designed so that to allow the impedance deviation

of the two CCFT lamps and the capacity deviation of barast capacitor.

Module

Inverter

* 3pin is V

LOW

LD14901-7

7. Timing Characteristics of input signals
Timing diagrams of input signal are shown in Fig.2 - .

7-1. Timing characteristics

Parameter Symbol

Mode

Min.

Typ.

Max.

Unit

Remark

Clock

Frequency

1/Tc all

25.18 28.33 MHz

High

time

Tch

Low

time

Tcl

Data

Setup time

Tds

Hold

time

Tdh

Horizontal Cycle

30.00 31.78 -

sync. signal

750 800 900

clock

Pulse

width

THp

2 96 200

clock

Vertical

Cycle

480

515

525

560

line

sync.

signal

400 446 449 480 line

350 447 449 510 line

Pulsewidth

TVp

all

34 line

Horizontal display period

THd

640 640 640

clock

Hsync-Clock

THc

Tc-10

phase

difference

Hsync-Vsync

TVh

TH-THp clock

phase difference

Note) In case of lower frequency, the deterioration of display quality, flicker etc.,may be occurred.

7-2. Horizontal display position

The horizontal display position is determined by ENAB signal and the input data corresponding

to the rising edge of ENAB signal is displayed at the left end of the active area.

Parameter symbol

Min.

Typ.

Max.

Unit

Remark

Enable signal Setup time

Tes

Tc-10 ns

Pulse

width

Tep

640

clock

Hsync-Enable signal

phase difference

THe 44 -

TH-664 clock

Note) When ENAB is fixed "Low", the display starts from the data of C104(clock) as shown
in Fig.2-. Be careful that the module does not work when ENAB is fixed "High".

When the phase difference is below 104 clock, keep the "High level of ENAB is signal longer

Than 104-The. If it will not be keeped, the display starts from the data of C104(clock).

LD14901-8

7-3. Vertical display position

The vertical display position is automatically centered in the active area at each mode

of VGA ,480-,400-,and 350-line mode . Each mode is selected depending on the polarity of

the synchronous signals described in 4-1(Note1).

In each mode ,the data of TVn is displayed at the top line of the active area. And the

display position will be centered on the screen like the following figure when the period of

vertical synchronous signal,TV,is typical value.

In 400-,and 350-line mode,the data in the vertical data invalid period is also displayed,

So ,inputting all data "0" is recommended during vertical data invalid period.

ENAB signal has no relation to the vertical display position.

Mode V-data

start(TVs)

V-data

period(TVd)

V-display start(TVn) V-display period Unit

Remark

480 34

480

line

400 34

400

443-TV

480

line

350 61

350

445-TV

480

line

7-4. Input Data Signals and Display Position on the screen

data invalid period

lines

400 lines mode (TV=449)

350 lines mode (TV=449)

data period

data invalid period

data period

D 1 , DH 1

D 1 , DH 2

D 1 , DH 3

D 2 , DH 2

D 2 , DH 1

D 3 , DH 1

D 6 4 0, DH 1

D640,DH480

D 1 , DH 48 0

R G B

D is pl ay positi on of i np ut da ta (480 l in es mo de )

LD14901-9

THc

C1*

C2*

* Only when enable terminal is fixed "Low"

Tds

Tdh

Tch

Tcl

D639

D640

Horizontal invalid da ta period

THp

C104*

Number of clock

Number of H-data

THe

Tes

THd

Tep

DH1

DH2

DH3

DH479

DH480

Vertical invalid data period

TVh

TVp

TVs

TVd

Number of V-data line

Fig 2-1 Input signal waveforms (480 line mode)

Horizontal

sync. signal

(Hsync)

Clock signal

(CK)

Data signal

(R0~R5,G0~G5,

B0~B5)

Data enable signal

(ENAB)

Vertical

sync. signal

(Vsync)

Horizontal

sync.

signal

(Hsync)

Data signal

(R0~R5,G0~G5,

B0~B5)

Horizontal invalid da ta period

Vertical invalid data period

0.3Vcc

0.7Vcc

0.3Vcc

0.7Vcc

0.3Vcc

0.7Vcc

0.3Vcc

0.7Vcc

0.3Vcc

0.7Vcc

Number of line

LD14901-10

THc

C1*

C2*

* Only when enable terminal (ENAB) is fixed "Low"

Tds

Tdh

Tch

Tcl

D639

D640

Horizontal data invalid

period

THp

C104*

Number of H-data

THe

Tes

THd

Tep

DH1

DH2

DH3

DH399

DH400

Vertical invalid data period

TVh

TVp

TVs

TVd

Number of line

Fig.2-2 Input signal waveforms (400 line mode)

Horizontal

sync.

signal

(Hsync)

Clock signal

(CK)

Data signal

(R0~R5,G0~G5,

B0~B5)

Data enable

signal

(ENAB)

Vertical

sync.

signal

(Vsync)

Horizontal

sync. signal

(Hsync)

Data signal

(R0~R5,G0~G5,

B0~B5)

Horizontal data invalid

period

Vertical invalid data period

0.3Vcc

0.7Vcc

0.3Vcc

0.7Vcc

0.3Vcc

0.7Vcc

0.3Vcc

0.7Vcc

Number of clock

Number of V-data line

LD14901-11

Horizontal

sync. signal

(Hsync)

Clock signal

(CK)

Data signal

(R0~R5,G0~G5,

B0~B5)

THc

C1*

C2*

Tds

Tdh

Tch

Tcl

D639

D640

Horizontal invalid data period

Data enable signal

(ENAB)

C104*

Number of H-data

THe

Tes

THd

Tep

THp

DH1

DH2

DH3

DH349

DH350

Vertical invalid data period

Vertical

sync. signal

(Vsync)

TVh

TVp

TVs

TVd

Number of V-data line

Number of

line

Fig.2-3 Input signal waveforms (350 line mode)

Horizontal

sync. signal

(Hsync)

Data signal

(R0~R5,G0~G5,

B0~B5)

* Only when enable terminal (ENAB) fixed to "Low"

Horizontal invalid data

period

Vertical invalid data period

0.7Vcc

0.3Vcc

0.7Vcc

0.3Vcc

0.7Vcc

0.3Vcc

0.7Vcc

0.3Vcc

0.7Vcc

0.3Vcc

Number of clock

LD14901-12

8. Input Signals, Basic Display Colors and Gray Scale of Each Color

Colors &

Data signal

Gray

scale

Gray

R0 R1 R2 R3 R4

R5 G0 G1 G2 G3 G4 G5 B0 B1 B2 B3

Scale

Black -

Blue -

Green -

Cyan -

Red -

Magenta -

Yellow -

White -

Black

GS0

GS1

Darker

GS2

Brighter

GS61

GS62

Red

GS63

Black

GS0

GS1

Darker

GS2

Brighter

GS61

GS62

Green

GS63

Black

GS0

GS1

Darker

GS2

Brighter

GS61

GS62

Blue

GS63

0 :Low level voltage, 1 : High level voltage

Each basic color can be displayed in 64 gray scales from 6 bit data signals. According to the combination of total 18 bit

data signals, the 262,144-color display can be achieved on the screen.

LD14901-13

9. Optical Characteristics

Ta=25, Vcc=+5V

Parameter Symbol

Condition

Min

Typ

Max

Unit

Remark

Viewing Horizontal

21,22

Deg.

Note1,4

Angle Vertical 11

Deg.

Range 12

Deg.

=°

150

Contrast ratio

Optimum

Viewing Angle

300

Note2,4

Response Rise r

=°

Note

3,4

Time Decay d

Chromaticity of

0.313

Note4

White

0.329

Luminance of white

280

350

cd/m

=6.0mArms

f=35kHz

White Unifomity

1.45

Note5

Horizontal

21,22

Deg.

Viewing

Angle range

as a

Brightness

Definition

Vertical

50% of

the

maximum

brightness

Deg.

Note1

The measurement shall be executed 30 minutes after

ghting at

rating.

(condition:I

6.0mArms)

The optical characteristics shall be measured in a dark room or equivalent state

with the method shown in Fig.3 below.

Photodetector (BM-5A:TOPCON)

Fig.3 Optical characteristics measurement method

Center of the screen

- module

panel

LD14901-14

Note1Definitions of viewing angle range:

N orm al lin e

2 2

1 2

2 1

6 o 'clo ck d irectio n

Note2Definition of contrast ratio:

The contrast ratio is defined as the following.

Contrast Ratio (CR)

Note3Definition of response time:

The response time is defined as the following figure and shall be measured by

switching the input signal for "black" and "white" .

90%

100%

white

black

10%

time

hotodetect

o
r
ou

t
p
u
t

(
r
e
l
a
ti
ve

a
lu

Note4This shall be measured at center of the screen.

Note5Definition of white uniformity:

White uniformity is defined as the

following with five measurements
(AE).

Luminance (brightness) with all pixels white
Luminance (brightness) with all pixels black

1 60

3 20

4 80

1 20

2 40

3 60

p ixel

Maximum Luminance of five points (brightness)

Minimum Luminance of five points (brightness)

LD14901-15

10. Display Quality

The display quality of the color TFT-LCD module shall be in compliance with the

Incoming Inspection Standard.

11Handling Precautions

a) Be sure to turn off the power supply when inserting or disconnecting the cable.

b) Be sure to design the cabinet so that the module can be installed without any extra stress such as

warp or twist.

c) Since the front polarizer is easily damaged, pay attention not to scratch it.

d) Wipe off water drop immediately. Long contact with water may cause discoloration or spots.

e) When the panel surface is soiled, wipe it with absorbent cotton or other soft cloth.

f) Since the panel is made of glass, it may break or crack if dropped or bumped on hard surface.

Handle with care.

g) Since CMOS LSI is used in this module, take care of static electricity and injure the human earth

when handling.

h) Protection film is attached to the module surface to prevent it from being scratched .

Peel the film off slowly , just before the use, with strict attention to electrostatic charges.

Blow off 'dust' on the polarizer by using an ionized nitrogen.

. i) The polarizer surface on the panel is treated with Anti-Glare for low reflection. In case of attaching

protective board over the LCD,be careful about the optical interface fringe etc. whiich degrades

display quality.

j)Do not expose the LCD panel to direct sunlight. Lightproof shade etc. should be attached when LCD panel is

used under such environment.

k) Connect GND to 4 place of mounting holes to stabilize against EMI and external noise.

l) There are high voltage portions on the backlight and very dangerous. Careless touch may lead to

electrical shock. When exchange lamps or service,turn off the power without tail.

m) When handling LCD modules and assembling them into cabinets, please be noted that long-term

storage in the environment of oxidization or deoxidization gas and the use of such materials as reagent,

solvent, adhesive, resin, etc. which generate these gasses, may cause corrosion and discoloration of the

LCD modules.

n)Cold cathode fluorescent lamp in LCD panel contains a small amount of mercury, please follow local

ordinances or regulations for disposal.

12.Packing form

Product Country

JAPAN

TAIWAN

Piling number of cartons

Max

Packing quantity in one carton

Carton size [mm]

525 (W)×309(D)×377(H)

Total mass of one carton filled

with full modules

17.5kg

Packing form is shown

Fig.4

LD14901-16

13Reliability test items
No. Test item

Conditions

1 High temperature storage test

Ta=70 240h

2 Low temperature storage test

Ta= -30 240h

3 High temperature

& high humidity operation test

Ta=40 ; 95%RH 240h
(No condensation)

4 High temperature operation test

Ta=65 240h

5 Low temperature operation test

Ta= -10 240h

6 Vibration test

(non- operating)

Frequency: 1057Hz/Vibration width (one side):0.075mm
: 58500Hz/Gravity:9.8m/s

Sweep time : 11 minutes
Test period : 3 hours
(1 hour for each direction of X,Y,Z)

7 Shock test

(non- operating)

Max. gravity : 490m/s

Pulse width : 11ms, half sine wave
Direction : ±X,±Y,±Z
once for each direction.

Result Evaluation Criteria
Under the display quality test conditions with normal operation state, these shall be no change
which may affect practical display function.

14Others

1) Label: Module

Case 1) Japan product only

Case 2) Taiwan product only

Packing Model.No Shipment Date Quntity

2) Adjusting volume have been set optimally before shipment, so do not change any adjusted value.

If adjusted value is changed, the specification may not be satisfied.

3) Disassembling the module can cause permanent damage and should be strictly avoided.

4) Please be careful since image retention may occur when a fixed pattern is displayed for a long time.

5) If any problem occurs in relation to the description of this specification , it shall be resolved

through discussion with spirit of cooperation.

LQ104V1DG21

LQ104V1DG21A

Model No.

Lot No.(DATE)

Quantity

User Model No.

Sharp internal Model No. for LCD modules
in the carton will be shown here.

LQ104V1DG21

LQ104V1DG21G

SHARP

MADE IN TAIWAN

LQ104V1DG21

35 Z00001 G A

SHARP

MADE IN JAPAN

Model No.
Lot No.

LQ104V1DG21

35 T00001 _ A

LD14901-17

15. Procedure to backlight replacement

Lamp which is used in the LCD module is consumable goods. When the lamp replacement is needed due to the expiry of
lamp-operating life, make sure that the power supply is turned off before the lamp replacement. Since there is high-
voltage current in the backlight area, an electric shock is likely to happen if the lamp is replaced without turning off the
power supply. The lamp replacement can be conducted by either horizontal slide method or backside exchange.

(1) By horizontal slide (See figure #5 & figure #6)

1) Pull-out the lamp unit to the direction which arrow "F" indicates by pressing the white latch of the plastic lamp unit by

using small flat-blade screwdriver to the either direction of "A" or "B" as shown in the figure #5.

2) Out of the 2 pcs of lamp units (2pcs/set), insert the replacement lamp which has triangle mark on the side of the lamp

unit into the slot of the metal area of LCD module which also has triangle mark. And then, insert the remaining lamp
unit which does not have triangle mark into the slot of the metal area of LCD module which also does not have triangle
mark. During the insertion, lamp unit can be inserted smoothly by pressing the transparent resin (light guide sheet)
inside the LCD module by using the end of the lamp unit to the direction which arrow "C" or arrow "D" indicate shown
in the figure #6, then insert the lamp unit to the direction which arrow "E" indicates in the figure #6.

3) Insert the lamp unit slowly and in a straight line during the lamp replacement in order not to break the lamp. Be

careful for any dust goes in. And make sure that lamp unit is completely inserted into the LCD module. You can hear
clicking noise when the lamp unit is completely inserted .

4) Replace the both of the lamp units in same time.

Detail view "G"

Edge of flat-blade screwdriver

White latch

Lamp unit

(Triangle mark on the side.)

White latch

Detail view "H"

Edge of flat-blade screwdriver

No triangle mark on the side of the
metal part of the LCD module.

Triangle mark on the side of the
metal part of the LCD module.

Lamp unit

(No triangle mark
on the side.)

Fig.5

LD14901-18

(2) How to replace from backside (See figure #7 & #8)

1) Remove 4 screws which hold the holder cover (sheet metal). (Please refer figure #7)
2) Slide the holder cover (sheet metal) to the direction which arrow "J" indicates. After checking that the nail is removed

from the hub "L", remove 2pcs holder cover (sheet metal).

3) Remove the lamp units.
4) Out of the 2 pcs of lamp units (2pcs/set), set the replacement lamp which has triangle mark on the side of the lamp

unit into the area of the LCD module which also has triangle mark on the rear side of the metal area. And then, set the
remaining lamp unit which does not have triangle mark into the area of the LCD module which does not have triangle
mark on the side of the metal area (Please refer figure #8).

5) Insert the nail of holder cover (sheet metal) into the hub "L"of the LCD module by sliding the 2 pcs of holder cover

(sheet metal) slightly to the direction which arrow "K" indicates in the figure #7.

6) Tighten 4 screws which hold 2 pcs holder cover (sheet metal) along the thread groove of the prepared hole. Tightening

torque is 1.6kgf.cm. If more torque is applied, the thread may damaged.

7) Insert the lamp unit slowly and in a straight line during the lamp replacement in order not to break the lamp. Be

careful that dirt or dust does not break into the module. And make sure that lamp unit is completely inserted.

8) Replace the both of the lamp units in same time.

Fig.6

Edge of lamp unit

Lamp unit

(Triangle mark
on the side.)

Edge of lamp unit

Lamp unit

(No triangle mark
on the side.)

SPECIFICATIONS ARE SUBJECT TO CHANGE WITHOUT NOTICE.

Suggested applications (if any) are for standard use; See Important Restrictions for limitations on special applications. See Limited
Warranty for SHARP's product warranty. The Limited Warranty is in lieu, and exclusive of, all other warranties, express or implied.
ALL EXPRESS AND IMPLIED WARRANTIES, INCLUDING THE WARRANTIES OF MERCHANTABILITY, FITNESS FOR USE AND
FITNESS FOR A PARTICULAR PURPOSE, ARE SPECIFICALLY EXCLUDED. In no event will SHARP be liable, or in any way responsible,
for any incidental or consequential economic or property damage.

NORTH AMERICA

EUROPE

JAPAN

SHARP Microelectronics of the Americas
5700 NW Pacific Rim Blvd.
Camas, WA 98607, U.S.A.
Phone: (1) 360-834-2500
Fax: (1) 360-834-8903
Fast Info: (1) 800-833-9437
www.sharpsma.com

SHARP Microelectronics Europe
Division of Sharp Electronics (Europe) GmbH
Sonninstrasse 3
20097 Hamburg, Germany
Phone: (49) 40-2376-2286
Fax: (49) 40-2376-2232
www.sharpsme.com

SHARP Corporation
Electronic Components & Devices
22-22 Nagaike-cho, Abeno-Ku
Osaka 545-8522, Japan
Phone: (81) 6-6621-1221
Fax: (81) 6117-725300/6117-725301
www.sharp-world.com

TAIWAN

SINGAPORE

KOREA

SHARP Electronic Components
(Taiwan) Corporation
8F-A, No. 16, Sec. 4, Nanking E. Rd.
Taipei, Taiwan, Republic of China
Phone: (886) 2-2577-7341
Fax: (886) 2-2577-7326/2-2577-7328

SHARP Electronics (Singapore) PTE., Ltd.
438A, Alexandra Road, #05-01/02
Alexandra Technopark,
Singapore 119967
Phone: (65) 271-3566
Fax: (65) 271-3855

SHARP Electronic Components
(Korea) Corporation
RM 501 Geosung B/D, 541
Dohwa-dong, Mapo-ku
Seoul 121-701, Korea
Phone: (82) 2-711-5813 ~ 8
Fax: (82) 2-711-5819

CHINA

HONG KONG

SHARP Microelectronics of China
(Shanghai) Co., Ltd.
28 Xin Jin Qiao Road King Tower 16F
Pudong Shanghai, 201206 P.R. China
Phone: (86) 21-5854-7710/21-5834-6056
Fax: (86) 21-5854-4340/21-5834-6057
Head Office:
No. 360, Bashen Road,
Xin Development Bldg. 22
Waigaoqiao Free Trade Zone Shanghai
200131 P.R. China
Email: smc@china.global.sharp.co.jp

SHARP-ROXY (Hong Kong) Ltd.
3rd Business Division,
17/F, Admiralty Centre, Tower 1
18 Harcourt Road, Hong Kong
Phone: (852) 28229311
Fax: (852) 28660779
www.sharp.com.hk
Shenzhen Representative Office:
Room 13B1, Tower C,
Electronics Science & Technology Building
Shen Nan Zhong Road
Shenzhen, P.R. China
Phone: (86) 755-3273731
Fax: (86) 755-3273735

Ð­Ð»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: LQ104V1DG21A

ÐÐ»ÐµÐºÑ‚Ñ€Ð¾Ð½Ð½Ñ‹Ð¹ ÐºÐ¾Ð¼Ð¿Ð¾Ð½ÐµÐ½Ñ‚: LQ104V1DG21A